Abstract: In this paper we have developed a FDTD simulation
code which can treat wave propagation of a monopole antenna in a
metallic case which covers with PML, and performed a series of three
dimensional FDTD simulations of electromagnetic wave propagation
in this space .We also provide a measurement set up in antenna lab
and fortunately the simulations and measurements show good
agreement. According to simulation and measurement results, we
confirmed that the computer program which had been written in
FORTRAN, works correctly.
Abstract: The amplitude response of infrared (IR) sensors
depends on the reflectance properties of the target. Therefore, in
order to use IR sensor for measuring distances accurately, prior
knowledge of the surface must be known. This paper describes the
Phong Illumination Model for determining the properties of a surface
and subsequently calculating the distance to the surface. The angular
position of the IR sensor is computed as normal to the surface for
simplifying the calculation. Ultrasonic (US) sensor can provide the
initial information on distance to obtain the parameters for this
method. In addition, the experimental results obtained by using
LabView are discussed. More care should be taken when placing the
objects from the sensors during acquiring data since the small change
in angle could show very different distance than the actual one.
Since stereo camera vision systems do not perform well under some
environmental conditions such as plain wall, glass surfaces, or poor
lighting conditions, the IR and US sensors can be used additionally to
improve the overall vision systems of mobile robots.
Abstract: In this paper, RSA encryption algorithm and its hardware
implementation in Xilinx-s Virtex Field Programmable Gate
Arrays (FPGA) is analyzed. The issues of scalability, flexible performance,
and silicon efficiency for the hardware acceleration of
public key crypto systems are being explored in the present work.
Using techniques based on the interleaved math for exponentiation,
the proposed RSA calculation architecture is compared to existing
FPGA-based solutions for speed, FPGA utilization, and scalability.
The paper covers the RSA encryption algorithm, interleaved multiplication,
Miller Rabin algorithm for primality test, extended Euclidean
math, basic FPGA technology, and the implementation details of
the proposed RSA calculation architecture. Performance of several
alternative hardware architectures is discussed and compared. Finally,
conclusion is drawn, highlighting the advantages of a fully flexible
& parameterized design.
Abstract: Abrasive Jet Machining is an Unconventional
machining process in which the metal is removed from brittle and
hard material in the form of micro-chips. With increase in need of
materials like ceramics, composites, in manufacturing of various
Mechanical & Electronic components, AJM has become a useful
technique for micro machining. The present study highlights the
influence of different parameters like Pressure, SOD, Time, Abrasive
grain size, nozzle diameter on the Metal removal of FRP (Fiber
Reinforced Polymer) composite by Abrasive jet machining. The
results of the Experiments conducted were analyzed and optimized
with TAGUCHI method of Optimization and ANOVA for Optimal
Value.
Abstract: Image mosaicing is a technique that permits to enlarge the field of view of a camera. For instance, it is employed to achieve panoramas with common cameras or even in scientific applications, to achieve the image of a whole culture in microscopical imaging. Usually, a mosaic of cell cultures is achieved through using automated microscopes. However, this is often performed in batch, through CPU intensive minimization algorithms. In addition, live stem cells are studied in phase contrast, showing a low contrast that cannot be improved further. We present a method to study the flat field from live stem cells images even in case of 100% confluence, this permitting to build accurate mosaics on-line using high performance algorithms.
Abstract: This paper presents a ray tracing simulation technique for characterize the radiowave propagation inside building. The implementation of an algorithm capable of enumerating a large number of propagation paths in interactive time for the special case of 2.5D. The effective dielectric constants of the building structure in the simulations are indicated. The study describes an efficient 2.5D model of ray tracing algorithm were compared with 3D model. The result of the first investigations is that the environment of the indoor wave significantly changes as we change the electric parameters of material constructions. A detailed analysis of the dependence of the indoor wave on the wideband characteristics of the channel: root mean square (RMS) delay spread characteristics and Mean excess delay, is also investigated.
Abstract: In this paper, a numerical study has been made to
analyze the transient 2-D flows of a viscous incompressible fluid
through channels with forward or backward constriction. Problems
addressed include flow through sudden contraction and sudden
expansion channel geometries with rounded and increasingly sharp
reentrant corner. In both the cases, numerical results are presented for
the separation and reattachment points, streamlines, vorticity and
flow patterns. A fourth order accurate compact scheme has been
employed to efficiently capture steady state solutions of the
governing equations. It appears from our study that sharpness of the
throat in the channel is one of the important parameters to control the
strength and size of the separation zone without modifying the
general flow patterns. The comparison between the two cases shows
that the upstream geometry plays a significant role on vortex growth
dynamics.
Abstract: Currently, there is no database or local norms for the
physical performance of Malaysian rugby players. This database or
norms are vital for Malaysian-s sports development as programs can
be setup to improve the current status. This pilot study was
conducted to evaluate the status of our semi professional rugby
players. The rugby players were randomly selected from the
Malaysian National team and several clubs in the Klang valley, Kuala
Lumpur Malaysia. 54 male rugby players (Age: 24.41 ± 4.06 years)
were selected for this pilot study. Height, bodyweight, percentage
body fat and body mass index (BMI) and several other physical tests
were performed. Results from the BLEEP test revealed an average of
level 9, shuttle 2 for the players. Interestingly, forwards were taller,
heavier, and had lower maximal aerobic power than backs in the
same team. In conclusion, the physical characteristics of the rugby
players were much lower when compared to international players
from other countries. From this pilot study, the physical performance
of the Malaysian team must be improved in order to further develop
the sports.
Abstract: Buckling-Restrained Braced Frame system(BRBFs)
are a new type of steel seismic-load-resisting system that has found
use in several countries because of its efficiency and its promise of
seismic performance far superior to that of conventional braced
frames. The system is addressed in the 2005 edition of the AISC
Seismic Provisions for Structural Steel Buildings, also a set of design
provisions has been developed by NEHRP. This report illustrates the
seismic design of buckling restrained braced frames and compares
the result of design in the application of earthquake load for ordinary
bracing systems and buckling restrained bracing systems to see the
advantage and disadvantages of this new type of seismic resisting
system in comparison with the old Ordinary Concentric Braced
Frame systems (OCBFs); they are defined by the provisions
governing their design.
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: The theoretical prediction of the acoustical
polarization effects in the heterogeneous composites, made of thick
elastic solids with thin nematic films, is presented. The numericalanalytical
solution to the problem of the different wave propagation
exhibits some new physical effects in the low frequency domain: the
appearance of the critical frequency and the existence of the narrow
transition zone where the wave rapidly changes its speed. The
associated wave attenuation is highly perturbed in this zone. We also
show the possible appearance of the critical frequencies where the
attenuation changes the sign. The numerical results of parametrical
analysis are presented and discussed.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: the current study presents a modeling framework to determine the torsion strength of an induction hardened splined shaft by considering geometry and material aspects with the aim to optimize the static torsion strength by selection of spline geometry and hardness depth. Six different spline geometries and seven different hardness profiles including non-hardened and throughhardened shafts have been considered. The results reveal that the torque that causes initial yielding of the induction hardened splined shaft is strongly dependent on the hardness depth and the geometry of the spline teeth. Guidelines for selection of the appropriate hardness depth and spline geometry are given such that an optimum static torsion strength of the component can be achieved.
Abstract: The seismic vulnerability of an urban area is of a great
deal for local authorities especially those facing earthquakes. So, it is
important to have an efficient tool to assess the vulnerability of
existing buildings. The use of the VIP (Vulnerability Index Program)
and the GIS (Geographic Information System) let us to identify the
most vulnerable districts of an urban area.
The use of the vulnerability index method lets us to assess the
vulnerability of the center town of Blida (Algeria) which is a
historical town and which has grown enormously during the last
decades. In this method, three levels of vulnerability are defined. The
GIS has been used to build a data base in order to perform different
thematic analyses. These analyses show the seismic vulnerability of
Blida.
Abstract: For positive integer s and t, the Ramsey number R(s, t)
is the least positive integer n such that for every graph G of order n, either G contains Ks as a subgraph or G contains Kt as a subgraph.
We construct the circulant graphs and use them to obtain lower bounds of some small Ramsey numbers.
Abstract: The fluorescent pseudomonad strain R81 is a root
colonizing rhizobacteria which promotes the growth of many plants
by various mechanisms. Its broth containing siderophore (ironchelating
compound) and 2,4- diacetyl phloroglucinol (DAPG) is
used for preparing bioinoculant formulations for agronomical
applications. Glycerol was found to be the best carbon source for
improved biomass production. Splitting of nitrogen source to NH4Cl
and urea had a stabilizing effect on pH during batch cultivation. Ltryptophan
at 0.5 % in the medium increased the siderophore
production to 850 mg/l. During batch cultivation of the strain in a
bioreactor, a maximum of 4 g/l of dry cell mass, 1.8 g/l of
siderophore and 20 mg/l of DAPG was achieved when glycerol was
15 g/l and C/N ratio was maintained at 12.5. In case of intermittent
feeding of fresh medium during fed-batch cultivation, the dry cell
mass was increased to 25 g/l with improved production of DAPG to
70 mg/l.
Abstract: Technical laboratories are typically considered as
highly hazardous places in the polytechnic institution when
addressing the problems of high incidences and fatality rates. In
conjunction with several topics covered in the technical curricular,
safety and health precaution should be highlighted in order to
connect to few key ideas of being safe. Therefore the assessment of
safety awareness in terms of safety and health about hazardous and
risks at laboratories is needed and has to be incorporated with
technical education and other training programmes. The purpose of
this study was to determine the efficacy of technical laboratory safety
in one of the polytechnics in northern region. The study examined
three related issues that were; the availability of safety material and
equipment, safety practice adopted by technical teachers and
administrator-s safety attitudes in enforcing safety to the students. A
model of efficacy technical laboratory was developed to test the
linear relationship between existing safety material and equipment,
teachers- safety practice and administrators- attitude in enforcing
safety and to identify which of technical laboratory safety issues was
the most pertinent factor to realize safety in technical laboratory.
This was done by analyzing survey-based data sets particularly those
obtained from samples of 210 students in the polytechnic. The
Pearson Correlation was used to measure the association between the
variables and to test the research hypotheses. The result of the study
has found that there was a significant correlation between existing
safety material and equipment, safety practice adopted by teacher
and administrator-s attitude. There was also a significant relationship
between technical laboratory safety and safety practice adopted by
teacher and between technical laboratory safety and administrator
attitude. Hence, safety practice adopted by teacher and administrator
attitude is vital in realizing technical laboratory safety.
Abstract: Space Vector Modulation (SVM) is an optimum Pulse Width Modulation (PWM) technique for an inverter used in a variable frequency drive applications. It is computationally rigorous and hence limits the inverter switching frequency. Increase in switching frequency can be achieved using Neural Network (NN) based SVM, implemented on application specific chips. This paper proposes a neural network based SVM technique for a Voltage Source Inverter (VSI). The network proposed is independent of switching frequency. Different architectures are investigated keeping the total number of neurons constant. The performance of the inverter is compared for various switching frequencies for different architectures of NN based SVM. From the results obtained, the network with minimum resource and appropriate word length is identified. The bit precision required for this application is identified. The network with 8-bit precision is implemented in the IC XCV 400 and the results are presented. The performance of NN based general purpose SVM with higher bit precision is discussed.
Abstract: In this paper, many techniques for blind identification of moving average (MA) process are presented. These methods utilize third- and fourth-order cumulants of the noisy observations of the system output. The system is driven by an independent and identically distributed (i.i.d) non-Gaussian sequence that is not observed. Two nonlinear optimization algorithms, namely the Gradient Descent and the Gauss-Newton algorithms are exposed. An algorithm based on the joint-diagonalization of the fourth-order cumulant matrices (FOSI) is also considered, as well as an improved version of the classical C(q, 0, k) algorithm based on the choice of the Best 1-D Slice of fourth-order cumulants. To illustrate the effectiveness of our methods, various simulation examples are presented.
Abstract: This paper reviews the optimization available
transmission capability (ATC) of power systems using a device of
FACTS named SSSC equipped with energy storage devices. So that,
emplacement and improvement of parameters of SSSC will be
illustrated. Thus, voltage magnitude constraints of network buses,
line transient stability constraints and voltage breakdown constraints
are considered. To help the calculations, a comprehensive program in
DELPHI is provided, which is able to simulate and trace the
parameters of SSSC has been installed on a specific line.
Furthermore, the provided program is able to compute ATC, TTC
and maximum value of their enhancement after using SSSC.