Abstract: By using an adequate thermal barrier coating in
buildings the energy saving will be happened. In this study, a range
of wall paints with different absorption coefficient in different
climates has been investigated. In order to study these effects, heating
and cooling loads of a common building with different ordinary
paints and paint with mineral coating have been calculated. The
effect of building paint in different climatic condition was studied
and comparison was done between ordinary paints and paint with
mineral insulators in temperate climate to obtain optimized energy
consumption. The results have been shown that coatings with
inorganic micro particles as insulation reduce the energy
consumption of buildings around 14%.
Abstract: The tribological test with Pin-On-Disc configuration
measures friction and wear properties in dry or lubricated sliding
surfaces of a variety of materials and coatings. Polymeric matrix
composites loaded with mineral filler were used, 1%, 3%, 10%, 30%,
and 50% mass percentage of filler, to reduce the material cost by
using mineral tailings. Using a pin-on-disc tribometer to quantify
coefficient of friction and wear resistance of the specimens. The
parameters known to performing the test were 300 rpm rotation,
normal load of 16N and duration of 33.5 minutes. The composite
with 10% mineral filler performed better, considering that the wear
resistance was good when compared to the other compositions and an
average low coefficient of friction, in the order of μ ≤ 0.15.
Abstract: The Flexible AC Transmission System (FACTS)
technology is a new advanced solution that increases the reliability
and provides more flexibility, controllability, and stability of a power
system. The Unified Power Flow Controller (UPFC), as the most
versatile FACTS device for regulating power flow, is able to control
respectively transmission line real power, reactive power, and node
voltage. The main purpose of this paper is to analyze the effect of the
UPFC on the load flow, the power losses, and the voltage stability
using NEPLAN software modules, Newton-Raphson load flow is
used for the power flow analysis and the modal analysis is used for
the study of the voltage stability. The simulation was carried out on
the IEEE 14-bus test system.
Abstract: Reinforced earth structures are generally subjected to cyclic loading generated from earthquakes. This paper presents a summary of the results and analyses of a testing program carried out in a large-scale multi-function geosynthetic testing apparatus that accommodates soil samples up to 1.0 m3. This apparatus performs different shear and pullout tests under both static and cyclic loading. The testing program was carried out to investigate the controlling factors affecting soil/geogrid interaction under cyclic loading. The extensibility of the geogrids, the applied normal stresses, the characteristics of the cyclic loading (frequency, and amplitude), and initial static load within the geogrid sheet were considered in the testing program. Based on the findings of the testing program, the effect of these parameters on the pullout resistance of geogrids, as well as the displacement mobility under cyclic loading were evaluated. Conclusions and recommendations for the design of reinforced earth walls under cyclic loading are presented.
Abstract: The power buck converter is the most widely used
DC/DC converter topology. They have a very large application area
such as DC motor drives, photovoltaic power system which require
fast transient responses and high efficiency over a wide range of load
current. This work proposes, the modelling of DC/DC power buck
converter using state-space averaging method and the current-mode
control using a proportional-integral controller. The efficiency of the
proposed model and control loop are evaluated with operating point
changes. The simulation results proved the effectiveness of the linear
model of DC/DC power buck converter.
Abstract: Cloud computing is a business model which provides
an easier management of computing resources. Cloud users can
request virtual machine and install additional softwares and configure
them if needed. However, user can also request virtual appliance
which provides a better solution to deploy application in much faster
time, as it is ready-built image of operating system with necessary
softwares installed and configured. Large numbers of virtual
appliances are available in different image format. User can
download available appliances from public marketplace and start
using it. However, information published about the virtual appliance
differs from each providers leading to the difficulty in choosing
required virtual appliance as it is composed of specific OS with
standard software version. However, even if user choses the
appliance from respective providers, user doesn’t have any flexibility
to choose their own set of softwares with required OS and
application. In this paper, we propose a referenced architecture for
dynamically customizing virtual appliance and provision them in an
easier manner. We also add our experience in integrating our
proposed architecture with public marketplace and Mi-Cloud, a cloud
management software.
Abstract: In this study, thermal fatigue properties of 400 series
ferritic stainless steels have been evaluated in the temperature ranges
of 200-800oC and 200-900oC. Systematic methods for control of
temperatures within the predetermined range and measurement of load
applied to specimens as a function of temperature during thermal
cycles have been established. Thermal fatigue tests were conducted
under fully constrained condition, where both ends of specimens were
completely fixed. It has been revealed that load relaxation behavior at
the temperatures of thermal cycle was closely related with the thermal
fatigue property. Thermal fatigue resistance of 430J1L stainless steel
is found to be superior to the other steels.
Abstract: Asphalt pavement itself is a mixture made up of mainly aggregates, binders, and fillers that acts as a composition used for pavement construction. An experimental program was setup to determine the fatigue performance test of Asphalt with three different grades of conventional binders. Asphalt specimen has achieved the maximum optimum bulk density and air voids with a consistent bulk density of 2.3 t/m3, with an air void of 5% ± 0.5, before loading into the Asphalt Mixture Performance Tested (AMPT) for fatigue test. The number of cycles is defined as the point where phase angle drops, which is caused by the formation of cracks due to the increasing micro cracks when asphalt is undergoing repeated cycles of loading. Thus, the data collected are analyzed using the drop of phase angle as failure criteria. Based in the data analyzed, it is evident that the fatigue life of asphalt lies on the grade of binder. The result obtained shows that all specimens do experience a drop in phase angle due to macro cracks in the asphalt specimen.
Abstract: The objective of this research is to develop a general technique so that one may predict the dynamic behaviour of a three-dimensional scale crane model subjected to time-dependent moving point forces by means of conventional finite element computer packages. To this end, the whole scale crane model is divided into two parts: the stationary framework and the moving substructure. In such a case, the dynamic responses of a scale crane model can be predicted from the forced vibration responses of the stationary framework due to actions of the four time-dependent moving point forces induced by the moving substructure. Since the magnitudes and positions of the moving point forces are dependent on the relative positions between the trolley, moving substructure and the stationary framework, it can be found from the numerical results that the time histories for the moving speeds of the moving substructure and the trolley are the key factors affecting the dynamic responses of the scale crane model.
Abstract: In this paper, it is aimed to improve autonomous flight
performance of a load-carrying (payload: 3 kg and total: 6kg)
unmanned aerial vehicle (UAV) through active wing and horizontal
tail active morphing and also integrated autopilot system parameters
(i.e. P, I, D gains) and UAV parameters (i.e. extension ratios of wing
and horizontal tail during flight) design. For this purpose, a loadcarrying
UAV (i.e. ZANKA-II) is manufactured in Erciyes
University, College of Aviation, Model Aircraft Laboratory is
benefited. Optimum values of UAV parameters and autopilot
parameters are obtained using a stochastic optimization method.
Using this approach autonomous flight performance of UAV is
substantially improved and also in some adverse weather conditions
an opportunity for safe flight is satisfied. Active morphing and
integrated design approach gives confidence, high performance and
easy-utility request of UAV users.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: Voltage level must be raised in order to deliver the
produced energy to the consumption zones with less loss and less
cost. Power transformers used to raise or lower voltage are important
parts of the energy transmission system. Power transformers used in
switchgear and power generation plants stay in human's intensive
habitat zones as a result of expanding cities. Accordingly, noise
levels produced by power transformers have begun more and more
important and they have established itself as one of the research field.
In this research, the noise cause on transformers has been
investigated, it's causes has been examined and noise measurement
techniques have been introduced. Examples of transformer noise test
results are submitted and precautions to be taken were discussed for
the purpose of decreasing of the noise which will occurred by
transformers.
Abstract: Growth and remodeling of biological structures have
gained lots of attention over the past decades. Determining the
response of living tissues to mechanical loads is necessary for a wide
range of developing fields such as prosthetics design or computerassisted
surgical interventions. It is a well-known fact that biological
structures are never stress-free, even when externally unloaded. The
exact origin of these residual stresses is not clear, but theoretically,
growth is one of the main sources. Extracting body organ’s shapes
from medical imaging does not produce any information regarding
the existing residual stresses in that organ. The simplest cause of such
stresses is gravity since an organ grows under its influence from
birth. Ignoring such residual stresses might cause erroneous results in
numerical simulations. Accounting for residual stresses due to tissue
growth can improve the accuracy of mechanical analysis results. This
paper presents an original computational framework based on gradual
growth to determine the residual stresses due to growth. To illustrate
the method, we apply it to a finite element model of a healthy human
face reconstructed from medical images. The distribution of residual
stress in facial tissues is computed, which can overcome the effect of
gravity and maintain tissues firmness. Our assumption is that tissue
wrinkles caused by aging could be a consequence of decreasing
residual stress and thus not counteracting gravity. Taking into
account these stresses seems therefore extremely important in
maxillofacial surgery. It would indeed help surgeons to estimate
tissues changes after surgery.
Abstract: This paper investigates the thermo-electric effects
around the crack and notch tips under the electric current load. The
research methods include the finite element analysis and thermal
imaging experiment. The finite element solutions show that the electric
current density field concentrates at the crack tip. Due to the Joule
heating, this electric concentration causes the hot spot at the tip zone.
From numerical and experimental results, this hot spot is identified.
The temperature of the hot spot is affected by the electric load,
operation time and geometry of the sample.
Abstract: Many embankment dams have suffered failures during
earthquakes due to the increase of pore water pressure under seismic
loading. After analyzing of the behavior of embankment dams under
severe earthquakes, major advances have been attained in the
understanding of the seismic action on dams. The present study concerns numerical analysis of the seismic
response of earth dams. The procedure uses a nonlinear stress-strain
relation incorporated into the code FLAC2D based on the finite
difference method. This analysis provides the variation of the pore
water pressure and horizontal displacement.
Abstract: While the feature sizes of recent Complementary Metal
Oxid Semiconductor (CMOS) devices decrease the influence of static
power prevails their energy consumption. Thus, power savings that
benefit from Dynamic Frequency and Voltage Scaling (DVFS) are
diminishing and temporal shutdown of cores or other microchip
components become more worthwhile. A consequence of powering off unused parts of a chip is that the
relative difference between idle and fully loaded power consumption
is increased. That means, future chips and whole server systems gain
more power saving potential through power-aware load balancing,
whereas in former times this power saving approach had only
limited effect, and thus, was not widely adopted. While powering
off complete servers was used to save energy, it will be superfluous
in many cases when cores can be powered down. An important
advantage that comes with that is a largely reduced time to respond
to increased computational demand. We include the above developments in a server power model
and quantify the advantage. Our conclusion is that strategies from
datacenters when to power off server systems might be used in the
future on core level, while load balancing mechanisms previously
used at core level might be used in the future at server level.
Abstract: Landfill leachates contain a number of persistent pollutants, including heavy metals. They have the ability to spread in ecosystems and accumulate in fish which most of them are classified as top-consumers of trophic chains. Fish are freely swimming organisms; but perhaps, due to their species-specific ecological and behavioral properties, they often prefer the most suitable biotopes and therefore, did not avoid harmful substances or environments. That is why it is necessary to evaluate the persistent pollutant dispersion in hydroecosystem using fish tissue metal concentration. In hydroecosystems of hybrid type (e.g. river-pond-river) the distance from the pollution source could be a perfect indicator of such a kind of metal distribution. The studies were carried out in the Kairiai landfill neighboring hybrid-type ecosystem which is located 5 km east of the Šiauliai City. Fish tissue (gills, liver, and muscle) metal concentration measurements were performed on two types of ecologically-different fishes according to their feeding characteristics: benthophagous (Gibel carp, roach) and predatory (Northern pike, perch). A number of mathematical models (linear, non-linear, using log and other transformations) have been applied in order to identify the most satisfactorily description of the interdependence between fish tissue metal concentration and the distance from the pollution source. However, the only one log-multiple regression model revealed the pattern that the distance from the pollution source is closely and positively correlated with metal concentration in all predatory fish tissues studied (gills, liver, and muscle).
Abstract: This paper describes a simple way to control the speed
of PMBLDC motor using Fuzzy logic control method. In the
conventional PI controller the performance of the motor system is
simulated and the speed is regulated by using PI controller. These
methods used to improve the performance of PMSM drives, but in
some cases at different operating conditions when the dynamics of
the system also vary over time and it can change the reference speed,
parameter variations and the load disturbance. The simulation is
powered with the MATLAB program to get a reliable and flexible
simulation. In order to highlight the effectiveness of the speed control
method the FLC method is used. The proposed method targeted in
achieving the improved dynamic performance and avoids the
variations of the motor drive. This drive has high accuracy, robust
operation from near zero to high speed. The effectiveness and
flexibility of the individual techniques of the speed control method
will be thoroughly discussed for merits and demerits and finally
verified through simulation and experimental results for comparative
analysis.
Abstract: For several hundred years, the design of railway tracks
has practically remained unchanged. Traditionally, rail tracks are
placed on a ballast layer due to several reasons, including economy,
rapid drainage, and high load bearing capacity. The primary function
of ballast is to distributing dynamic track loads to sub-ballast and
subgrade layers, while also providing lateral resistance and allowing
for rapid drainage. Upon repeated trainloads, the ballast becomes
fouled due to ballast degradation and the intrusion of fines which
adversely affects the strength and deformation behaviour of ballast.
This paper presents the use of three-dimensional discrete element
method (DEM) in studying the shear behaviour of the fouled ballast
subjected to direct shear loading. Irregularly shaped particles of
ballast were modelled by grouping many spherical balls together in
appropriate sizes to simulate representative ballast aggregates. Fouled
ballast was modelled by injecting a specified number of miniature
spherical particles into the void spaces. The DEM simulation
highlights that the peak shear stress of the ballast assembly decreases
and the dilation of fouled ballast increases with an increase level of
fouling. Additionally, the distributions of contact force chain and
particle displacement vectors were captured during shearing progress,
explaining the formation of shear band and the evolutions of
volumetric change of fouled ballast.