Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.
Abstract: Negative pressure phenomenon appears in many
thermodynamic, geophysical and biophysical processes in the Nature
and technological systems. For more than 100 years of the laboratory
researches beginning from F. M. Donny’s tests, the great values of
negative pressure have been achieved. But this phenomenon has not
been practically applied, being only a nice lab toy due to the special
demands for the purity and homogeneity of the liquids for its
appearance. The possibility of creation of direct wave of negative
pressure in real heterogeneous liquid systems was confirmed
experimentally under the certain kinetic and hydraulic conditions.
The negative pressure can be considered as the factor of both useful
and destroying energies. The new approach to generation of the
negative pressure waves in impure, unclean fluids has allowed the
creation of principally new energy saving technologies and
installations to increase the effectiveness and efficiency of different
production processes. It was proved that the negative pressure is one
of the main factors causing hard troubles in some technological and
natural processes. Received results emphasize the necessity to take
into account the role of the negative pressure as an energy factor in
evaluation of many transient thermohydrodynamic processes in the
Nature and production systems.
Abstract: In and around Erode District, it is estimated that more
than 1250 chemical and allied textile processing fabric industries are
affected, partially closed and shut off for various reasons such as poor
management, poor supplier performance, lack of planning for
productivity, fluctuation of output, poor investment, waste analysis,
labor problems, capital/labor ratio, accumulation of stocks, poor
maintenance of resources, deficiencies in the quality of fabric, low
capacity utilization, age of plant and equipment, high investment and
input but low throughput, poor research and development, lack of
energy, workers’ fear of loss of jobs, work force mix and work ethic.
The main objective of this work is to analyze the existing conditions
in textile fabric sector, validate the break even of Total Productivity
(TP), analyze, design and implement fuzzy sets and mathematical
programming for improvement of productivity and quality
dimensions in the fabric processing industry. It needs to be
compatible with the reality of textile and fabric processing industries.
The highly risk events from productivity and quality dimension were
found by fuzzy systems and results are wrapped up among the textile
fabric processing industry.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.
Abstract: Code- mixing in spontaneous speech has been widely
discussed, but not in virtual situations; especially in context of the
third language learning students. Thus, this study is an attempt to
explore the linguistic characteristics of the mixing of Japanese,
English and Thai in a mobile Line chat room by students with their
background of English as L2, Japanese as L3 and Thai as mother
tongue. The result found that insertion of Thai content words is a very
common linguistic phenomenon embedded with the other two
languages in the sentences. As chatting is to be ‘relational’ or
‘interactional’, it affected the style of lexical choices to be speech-like,
more personal and emotionally-related. A personal pronoun in
Japanese is often mixed into the sentences. The Japanese
sentence-final question particle か “ka” was added to the end of the
sentence based on Thai grammar rules. Some unique characteristics
were created while chatting.
Abstract: Prior to quantifying the variables of the information
model for using school terminology in Croatia's region of Dalmatia
from 1884 to 2014, the most relevant model variables had to be
determined: historical circumstances, standard of living, education
system, linguistic situation, and media. The research findings show
that there was no significant transfer of the 1884 school terms into
1949 usage; likewise, the 1949 school terms were not widely used in
2014. On the other hand, the research revealed that the meaning of
school terms changed over the decades. The quantification of the
variables will serve as the groundwork for creating an information
model for using school terminology in Dalmatia from 1884 to 2014
and for defining direct growth rates in further research.
Abstract: Motion Tracking and Stereo Vision are complicated,
albeit well-understood problems in computer vision. Existing
softwares that combine the two approaches to perform stereo motion
tracking typically employ complicated and computationally expensive
procedures. The purpose of this study is to create a simple and
effective solution capable of combining the two approaches. The
study aims to explore a strategy to combine the two techniques
of two-dimensional motion tracking using Kalman Filter; and depth
detection of object using Stereo Vision. In conventional approaches
objects in the scene of interest are observed using a single camera.
However for Stereo Motion Tracking; the scene of interest is
observed using video feeds from two calibrated cameras. Using two
simultaneous measurements from the two cameras a calculation for
the depth of the object from the plane containing the cameras is made.
The approach attempts to capture the entire three-dimensional spatial
information of each object at the scene and represent it through a
software estimator object. In discrete intervals, the estimator tracks
object motion in the plane parallel to plane containing cameras and
updates the perpendicular distance value of the object from the plane
containing the cameras as depth. The ability to efficiently track
the motion of objects in three-dimensional space using a simplified
approach could prove to be an indispensable tool in a variety of
surveillance scenarios. The approach may find application from high
security surveillance scenes such as premises of bank vaults, prisons
or other detention facilities; to low cost applications in supermarkets
and car parking lots.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: Compositions of different molar ratios of
polymethylmethacrylate-co-methacrylic acid (PMMA-co-MAA)
were synthesized via free-radical polymerization. Polymer coated
surfaces have been produced on silicon wafers. Coated samples were
analyzed by atomic force microscopy (AFM). The results have shown
that the roughness of the surfaces have increased by increasing the
molar ratio of monomer methacrylic acid (MAA). This study reveals
that the gradual increase in surface roughness is due to the fact that
carboxylic functional groups have been generated by MAA segments.
Such surfaces can be desirable platforms for fabrication of the
biosensors for detection of the viruses and diseases.
Abstract: Shortfall of electrical energy in Pakistan is a challenge
adversely affecting its industrial output and social growth. As
elsewhere, Pakistan derives its electrical energy from a number of
conventional sources. The exhaustion of petroleum and conventional
resources, the rising costs coupled with extremely adverse climatic
effects are taking its toll especially on the under-developed countries
like Pakistan. As alternate, renewable energy sources like hydropower,
solar, wind, even bio-energy and a mix of some or all of them
could provide a credible alternative to the conventional energy
resources that would not only be cleaner but sustainable as well. As a
model, solar energy-based power grid for the near future has been
attempted to offset the energy shortfalls as a mix with our existing
sustainable natural energy resources. An assessment of solar energy
potential for electricity generation is being presented for fulfilling the
energy demands with higher level of reliability and sustainability.
This model is based on the premise that solar energy potential of
Pakistan is not only reliable but also sustainable. This research
estimates the present & future approaching renewable energy
resource specially the impact of solar energy based power grid for
mitigating energy shortage in Pakistan.
Abstract: Mahasweta Devi and Toni Morrison are the two
stalwarts of the Indian English and the Afro-American literature
respectively. The writings of these two novelists are authentic and
powerful records of the lives of the people because much of their
personal experiences have gone into the making of their works. Devi,
a representative force of the Indian English literature, is also a social
activist working with the tribals of Bihar, Jharkhand, Orissa and West
Bengal. Most of her works echo the lives and struggles of the
subalterns as is evident in her “best beloved book” Chotti Munda and
His Arrow. The novelist focuses on the struggle of the tribals against
the colonial and the feudal powers to create their own identity,
thereby, embarking on the ideological project of ‘setting the record
straight’. The Nobel Laureate Toni Morrison, on the other hand,
brings to the fore the crucial issues of gender, race and class in many
of her significant works. In one of her representative works Sula, the
protagonist emerges as a non- conformist and directly confronts the
notion of a ‘good woman’ nurtured by the community of the Blacks.
In addition to this, the struggle of the Blacks against the White
domination, also become an important theme of the text. The thrust
of the paper lies in making a critical analysis of the portrayal of the
heroic attempts of the subaltern protagonist and the artistic endeavor
of the novelists in challenging the stereotypes.
Abstract: The thyroid gland is the largest classic endocrine
organ that effects many organs of the body and plays a significant
role in the process of Metabolism in animals. The aim of this study
was to investigate the prevalence of thyroid disorders diagnosed by
ultrasound and microscopic Lesions of the thyroid during the
slaughter of apparently healthy One Humped Camels (Camelus
dromedarius) in Iran. Randomly, 520 male camels (With an age
range of 4 to 8 years), were studied in 2012 to 2013. The Camels’
thyroid glands were evaluated by sonographic examination. In both
longitudinal and transverse view and then tissue sections were
provide and stained with H & E and finally examined by light
microscopy. The results obtained indicated the following:
hyperplastic goiter (21%), degenerative changes (12%), follicular
cysts (8%), follicular atrophy (4%), nodular hyperplasia (3%),
adenoma (1%), carcinoma (1%) and simple goiter colloid (1%).
Ultrasound evaluation of thyroid gland in adenoma and carcinoma
showed enlargement and irregular of the gland, decreased
echogenicity, and the heterogeneous thyroid parenchyma. Also, in
follicular cysts were observed in the enlarged gland with no echo
structures of different sizes and decreased echogenicity as a local or
general. In nodular hyperplasia, increase echogenicity and
heterogeneous parenchymal were seen. These findings suggest the
use of sonography and pathology as a screening test in the diagnosis
of complications of thyroid disorders.
Abstract: As the current status and growth of Indian automobile
industry is remarkable, transportation sectors are the main concern in
terms of energy security and climate change. Due to rising demand of
fuel and its dependency on foreign countries that affects the GDP of
nation, suggests that penetration of electrical vehicle will increase in
near future. So in this context analysis is done if the 10 percent of
conventional vehicles including cars, three wheelers and two
wheelers becomes electrical vehicles in near future which is also a
part of Nations Electric Mobility Mission Plan then the saving which
improves the nation’s economy is analyzed in detail. Whether the
Indian electricity grid is capable of taking this load with current
generation and demand all over the country is also analyzed in detail.
Current situation of Indian grid is analyzed and how the gap between
generation and demand can be reduced is discussed in terms of
increasing generation capacity and energy conservation measures.
Electrical energy conservation measures in Industry and especially in
rural areas have been analyzed to improve performance of Indian
electricity grid in context of electrical vehicle penetration in near
future. Author was a part of Vishvakarma yojna in which energy
losses were measured in 255 villages of Gujarat and solutions were
suggested to mitigate them and corresponding reports was submitted
to the authorities of Gujarat government.
Abstract: Burnishing is increasingly used as a finishing operation to improve surface roughness and surface hardness. This can be achieved by applying a hard ball or roller onto metallic surfaces under pressure, in order to achieve many advantages in the metallic surface. In the present work, the feed rate, speed and force have been considered as the basic burnishing parameters to study the surface roughness and surface hardness of metallic matrix composites. The considered metal matrix composites were made from Aluminum-Magnesium-Graphite with five different weight percentage of graphite. Both effects of burnishing parameters mentioned above and the graphite percentage on the surface hardness and surface roughness of the metallic matrix composites were studied. The results of this investigation showed that the surface hardness of the metallic composites increases with the increase of the burnishing force and decreases with the increase in the burnishing feed rate and burnishing speed. The surface roughness of the metallic composites decreases with the increasing of the burnishing force, feed rate, and speed to certain values, then it starts to increase. On the other hand, the increase in the weight percentage of the graphite in the considered composites causes a decrease in the surface hardness and an increase in the surface roughness.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: Laser beam welding of dissimilar sheet metal
combinations such as Ti/Al, SS/Al and Cu/Al are increasingly
demanded due to high energy densities with less fusion and heat
affected zones. A good weld joint strength involves combinations of
dissimilar metals and the formation of solid solution in the weld pool.
Many metal pairs suffer from significant intermetallic phase
formation during welding which greatly reduces their strength. The
three different sheet metal mentioned above is critically reviewed and
phase diagram for the combinations are given. The aim of this study
is to develop an efficient metal combinations and the influence on
their interfacial characteristics. For that the following parameters
such as weld geometry, residual distortion, micro hardness,
microstructure and mechanical properties are analyzed
systematically.
Abstract: An existing RC building in Madinah is seismically
evaluated with and without infill wall. Four model systems have been
considered i.e. model I (no infill), model IIA (strut infill-update from
field test), model IIB (strut infill- ASCE/SEI 41) and model IIC (strut
infill-Soft storey- ASCE/SEI 41). Three dimensional pushover
analyses have been carried out using SAP2000 software
incorporating inelastic material behavior for concrete, steel and infill
walls. Infill wall has been modeled as equivalent strut according to
suggested equation matching field test measurements and to the
ASCE/SEI 41 equation. The effect of building modeling on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madinah area has been investigated. The
response modification factor (R) for the 5 story RC building is
evaluated from capacity and demand spectra (ATC-40) for the
studied models. The results are summarized and discussed.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: Contracting authorities in the public sector are
obligated to apply the principles provided for in the Polish law for the
evaluation and selection of contractors. In order to analyse the
methods of contractors selecting applied in practice by public clients,
the notices of contract award results for construction works were
analysed. The analysis shows that the procedure selected more and
more often is open competitive bidding, where the assessment of the
competence of contractors is not very precise, as well as noncompetitive
bidding, i.e. single source procurement. The share of
procurement procedures, where the only criterion is price, is
increasing. The solution to the problems existing here might be the
introduction of one of the forms of pre-selection of contractors. The
article also briefly discusses verification systems for companies
applying for public contracts used in EU countries.