Abstract: Construction cost estimation is one of the most
important aspects of construction project design. For generations, the
process of cost estimating has been manual, time-consuming and
error-prone. This has partly led to most cost estimates to be unclear
and riddled with inaccuracies that at times lead to over- or underestimation
of construction cost. The development of standard set of
measurement rules that are understandable by all those involved in a
construction project, have not totally solved the challenges. Emerging
Building Information Modelling (BIM) technologies can exploit
standard measurement methods to automate cost estimation process
and improve accuracies. This requires standard measurement
methods to be structured in ontological and machine readable format;
so that BIM software packages can easily read them. Most standard
measurement methods are still text-based in textbooks and require
manual editing into tables or Spreadsheet during cost estimation. The
aim of this study is to explore the development of an ontology based
on New Rules of Measurement (NRM) commonly used in the UK for
cost estimation. The methodology adopted is Methontology, one of
the most widely used ontology engineering methodologies. The
challenges in this exploratory study are also reported and
recommendations for future studies proposed.
Abstract: The present work aims to throw light on the effects of
arcing in air on the surface state of contact pastilles made of silvernickel
Ag-Ni (60/40). Also, the photoelectric emission from these
electrical contacts has been investigated in the spectral range of 196-
256 nm. In order to study the effects of arcing on the EWF, the
metallic samples were subjected to electrical arcs in air, at
atmospheric pressure and room temperature, after that, they have
been introduced into the vacuum chamber of an experimental UHV
set-up for EWF measurements. Both Fowler method of isothermal
curves and linearized Fowler plots were used for the measurement of
the EWF by the photoelectric effect.
It has been found that the EWF varies with the number of applied
arcs. Thus, after 500 arcs in air, the observed EWF increasing is
probably due to progressive inclusion of oxide on alloy surface.
Microscopic examination is necessary to get better understandings on
EWF of silver alloys, for both virgin and arced electrical contacts.
Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.
Abstract: A new method for determining the distribution of
birefringence and linear dichroism in optical polymer materials is
presented. The method is based on the use of polarizationholographic
diffraction grating that forms an orthogonal circular basis
in the process of diffraction of probing laser beam on the grating. The
intensities ratio of the orders of diffraction on this grating enables the
value of birefringence and linear dichroism in the sample to be
determined. The distribution of birefringence in the sample is
determined by scanning with a circularly polarized beam with a
wavelength far from the absorption band of the material. If the
scanning is carried out by probing beam with the wavelength near to
a maximum of the absorption band of the chromophore then the
distribution of linear dichroism can be determined. An appropriate
theoretical model of this method is presented. A laboratory setup was
created for the proposed method. An optical scheme of the laboratory
setup is presented. The results of measurement in polymer films with
two-dimensional gradient distribution of birefringence and linear
dichroism are discussed.
Abstract: In this paper, Bayesian online inference in models of
data series are constructed by change-points algorithm, which
separated the observed time series into independent series and study
the change and variation of the regime of the data with related
statistical characteristics. variation of statistical characteristics of time
series data often represent separated phenomena in the some
dynamical system, like a change in state of brain dynamical reflected
in EEG signal data measurement or a change in important regime of
data in many dynamical system. In this paper, prediction algorithm
for studying change point location in some time series data is
simulated. It is verified that pattern of proposed distribution of data
has important factor on simpler and smother fluctuation of hazard
rate parameter and also for better identification of change point
locations. Finally, the conditions of how the time series distribution
effect on factors in this approach are explained and validated with
different time series databases for some dynamical system.
Abstract: In this paper, we considered and applied parametric
modeling for some experimental data of dynamical system. In this
study, we investigated the different distribution of output
measurement from some dynamical systems. Also, with variance
processing in experimental data we obtained the region of
nonlinearity in experimental data and then identification of output
section is applied in different situation and data distribution. Finally,
the effect of the spanning the measurement such as variance to
identification and limitation of this approach is explained.
Abstract: Motion Tracking and Stereo Vision are complicated,
albeit well-understood problems in computer vision. Existing
softwares that combine the two approaches to perform stereo motion
tracking typically employ complicated and computationally expensive
procedures. The purpose of this study is to create a simple and
effective solution capable of combining the two approaches. The
study aims to explore a strategy to combine the two techniques
of two-dimensional motion tracking using Kalman Filter; and depth
detection of object using Stereo Vision. In conventional approaches
objects in the scene of interest are observed using a single camera.
However for Stereo Motion Tracking; the scene of interest is
observed using video feeds from two calibrated cameras. Using two
simultaneous measurements from the two cameras a calculation for
the depth of the object from the plane containing the cameras is made.
The approach attempts to capture the entire three-dimensional spatial
information of each object at the scene and represent it through a
software estimator object. In discrete intervals, the estimator tracks
object motion in the plane parallel to plane containing cameras and
updates the perpendicular distance value of the object from the plane
containing the cameras as depth. The ability to efficiently track
the motion of objects in three-dimensional space using a simplified
approach could prove to be an indispensable tool in a variety of
surveillance scenarios. The approach may find application from high
security surveillance scenes such as premises of bank vaults, prisons
or other detention facilities; to low cost applications in supermarkets
and car parking lots.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: An existing RC building in Madinah is seismically
evaluated with and without infill wall. Four model systems have been
considered i.e. model I (no infill), model IIA (strut infill-update from
field test), model IIB (strut infill- ASCE/SEI 41) and model IIC (strut
infill-Soft storey- ASCE/SEI 41). Three dimensional pushover
analyses have been carried out using SAP2000 software
incorporating inelastic material behavior for concrete, steel and infill
walls. Infill wall has been modeled as equivalent strut according to
suggested equation matching field test measurements and to the
ASCE/SEI 41 equation. The effect of building modeling on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madinah area has been investigated. The
response modification factor (R) for the 5 story RC building is
evaluated from capacity and demand spectra (ATC-40) for the
studied models. The results are summarized and discussed.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: For cycling, the analysis of the pedal force is one of the
important factors in the study of exercise ability assessment and
overuse injuries. In past studies, a two-axis measurement sensor was
used at the sagittal plane to measure the force only in the anterior,
posterior, and vertical directions and to analyze the loss of force and
the injury on the frontal plane due to the forces in the right and left
directions. In this study, which is a basic study on diverse analyses of
the pedal force that consider the forces on the sagittal plane and the
frontal plane, a three-axis pedal force measurement sensor was
developed to measure the anterior-posterior (Fx), medio-lateral (Fz),
and vertical (Fy) forces. The sensor was fabricated with a size and
shape similar to those of the general flat pedal, and had a 550g weight
that allowed smooth pedaling. Its measurement range was ±1000 N for
Fx and Fz and ±2000 N for Fy, and its non-linearity, hysteresis, and
repeatability were approximately 0.5%. The data were sampled at
1000 Hz using a signal collector. To use the developed sensor, the
pedaling efficiency (index of efficiency, IE) and the range of left and
right (medio-lateral, ML) forces were measured with two seat heights
(low and high). The results of the measurement showed that the IE was
higher and the force range in the ML direction was lower with the high
position than with the low position. The developed measurement
sensor and its application results will be useful in understanding and
explaining the complicated pedaling technique, and will enable
diverse kinematic analyses of the pedal force on the sagittal plane and
the frontal plane.
Abstract: To date, one of the few comprehensive indicators for
the measurement of food security is the Global Food Security Index
(GFSI). This index is a dynamic quantitative and qualitative
benchmarking model, constructed from 28 unique indicators, that
measures drivers of food security across both developing and
developed countries. Whereas the GFSI has been calculated across a
set of 109 countries, in this paper we aim to present and compare, for
the Middle East and North Africa (MENA), 1) the Food Security
Index scores achieved and 2) the data available on affordability,
availability, and quality of food. The data for this work was taken
from the latest available report published by the creators of the GFSI,
which in turn used information from national and international
statistical sources. MENA countries rank from place 17/109 (Israel,
although with resent political turmoil this is likely to have changed)
to place 91/109 (Yemen) with household expenditure spent in food
ranging from 15.5% (Israel) to 60% (Egypt). Lower spending on food
as a share of household consumption in most countries and better
food safety net programs in the MENA have contributed to a notable
increase in food affordability. The region has also, however,
experienced a decline in food availability, owing to more limited
food supplies and higher volatility of agricultural production. In
terms of food quality and safety the MENA has the top ranking
country (Israel). The most frequent challenges faced by the countries
of the MENA include public expenditure on agricultural research and
development as well as volatility of agricultural production. Food
security is a complex phenomenon that interacts with many other
indicators of a country’s wellbeing; in the MENA it is slowly but
markedly improving.
Abstract: In this paper, we propose a method for three-dimensional
(3-D)-model indexing based on defining a new
descriptor, which we call new descriptor using spherical harmonics.
The purpose of the method is to minimize, the processing time on the
database of objects models and the searching time of similar objects
to request object.
Firstly we start by defining the new descriptor using a new
division of 3-D object in a sphere. Then we define a new distance
which will be used in the search for similar objects in the database.
Abstract: In this study, the performance analyses of the twenty
five Coal-Fired Power Plants (CFPPs) used for electricity generation
are carried out through various Data Envelopment Analysis (DEA)
models. Three efficiency indices are defined and pursued. During the
calculation of the operational performance, energy and non-energy
variables are used as input, and net electricity produced is used as
desired output (Model-1). CO2 emitted to the environment is used as
the undesired output (Model-2) in the computation of the pure
environmental performance while in Model-3 CO2 emissions is
considered as detrimental input in the calculation of operational and
environmental performance. Empirical results show that most of the
plants are operating in increasing returns to scale region and Mettur
plant is efficient one with regards to energy use and environment.
The result also indicates that the undesirable output effect is
insignificant in the research sample. The present study will provide
clues to plant operators towards raising the operational and
environmental performance of CFPPs.
Abstract: One of the major difficulties introduced with wind
power penetration is the inherent uncertainty in production originating
from uncertain wind conditions. This uncertainty impacts many
different aspects of power system operation, especially the balancing
power requirements. For this reason, in power system development
planing, it is necessary to evaluate the potential uncertainty in future
wind power generation. For this purpose, simulation models are
required, reproducing the performance of wind power forecasts.
This paper presents a wind power forecast error simulation models
which are based on the stochastic process simulation. Proposed
models capture the most important statistical parameters recognized
in wind power forecast error time series. Furthermore, two distinct
models are presented based on data availability. First model uses
wind speed measurements on potential or existing wind power plant
locations, while the seconds model uses statistical distribution of wind
speeds.
Abstract: Measurements and quantitative analysis of kinematic
parameters of human hand movements have an important role in
different areas such as hand function rehabilitation, modeling of
multi-digits robotic hands, and the development of machine-man
interfaces. In this paper the assessment and evaluation of the reachto-
grasp movement by using computerized and robot-assisted method
is described. Experiment involved the measurements of hand
positions of seven healthy subjects during grasping three objects of
different shapes and sizes. Results showed that three dominant phases
of reach-to-grasp movements could be clearly identified.
Abstract: In this paper, extract of papaya leaves are used as a
natural dye and combined by variations of solvent concentration
applied on DSSC (Dye-Sensitized Solar Cell). Indonesian geographic
located on the equator line occasions the magnitude of the potential
to develop organic solar cells made from extracts of chlorophyll as a
substitute for inorganic materials or synthetic dye on DSSC material.
Dye serves as absorbing photons which are then converted into
electrical energy. A conductive coated glass layer called TCO
(Transparent Conductive Oxide) is used as a substrate of electrode.
TiO2 nanoparticles as binding dye molecules, redox couple iodide/
tri-iodide as the electrolyte and carbon as the counter electrode in the
DSSC are used. TiO2 nanoparticles, organic dyes, electrolytes, and
counter electrode are arranged and combined with the layered
structure of the photo-catalyst absorption layer. Dye absorption
measurements using a spectrophotometer at 400-800 nm light
spectrum produces a total amount of chlorophyll 80.076 mg/l. The
test cell at 7 watt LED light with 5000 lux luminescence was
obtained Voc and Isc of 235.5 mV and 14 μA, respectively.
Abstract: This paper describes a novel application of Fiber
Braggs Grating (FBG) sensors in the assessment of human postural
stability and balance on an unstable platform. In this work, FBG
sensor Stability Analyzing Device (FBGSAD) is developed for
measurement of plantar strain to assess the postural stability of
subjects on unstable platforms during different stances in eyes open
and eyes closed conditions on a rocker board. The studies are
validated by comparing the Centre of Gravity (CG) variations
measured on the lumbar vertebra of subjects using a commercial
accelerometer. The results obtained from the developed FBGSAD
depict qualitative similarities with the data recorded by commercial
accelerometer. The advantage of the FBGSAD is that it measures
simultaneously plantar strain distribution and postural stability of the
subject along with its inherent benefits like non-requirement of
energizing voltage to the sensor, electromagnetic immunity and
simple design which suits its applicability in biomechanical
applications. The developed FBGSAD can serve as a tool/yardstick to
mitigate space motion sickness, identify individuals who are
susceptible to falls and to qualify subjects for balance and stability,
which are important factors in the selection of certain unique
professionals such as aircraft pilots, astronauts, cosmonauts etc.
Abstract: Nowadays, the successful implementation of ICTs is
vital for almost any kind of organization. Good governance and ICT
management are essential for delivering value, managing
technological risks, managing resources and performance
measurement. In addition, outsourcing is a strategic IT service
solution which complements IT services provided internally in
organizations. This paper proposes the measurement tools of a new
holistic maturity model based on standards ISO/IEC 20000 and
ISO/IEC 38500, and the frameworks and best practices of ITIL and
COBIT, with a specific focus on IT outsourcing. These measurement
tools allow independent validation and practical application in the
field of higher education, using a questionnaire, metrics tables, and
continuous improvement plan tables as part of the measurement
process. Guidelines and standards are proposed in the model for
facilitating adaptation to universities and achieving excellence in the
outsourcing of IT services.