Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: The aim of the performed work is to establish the 2D
and 3D model of direct unsteady task of sample heat treatment by
moving source employing computer model on the basis of finite
element method. Complex boundary condition on heat loaded sample
surface is the essential feature of the task. Computer model describes
heat treatment of the sample during heat source movement over the
sample surface. It is started from 2D task of sample cross section as a
basic model. Possibilities of extension from 2D to 3D task are
discussed. The effect of the addition of third model dimension on
temperature distribution in the sample is showed. Comparison of
various model parameters on the sample temperatures is observed.
Influence of heat source motion on the depth of material heat
treatment is shown for several velocities of the movement. Presented
computer model is prepared for the utilization in laser treatment of
machine parts.
Abstract: This study aims at improving the urban hydrological
cycle of the Orléans agglomeration (France) and understanding the
relationship between physical and chemical parameters of urban
surface runoff and the hydrological conditions. In particular water
quality parameters such as pH, conductivity, total dissolved solids,
major dissolved cations and anions, and chemical and biological
oxygen demands were monitored for three types of urban water
discharges (wastewater treatment plant output (WWTP), storm
overflow and stormwater outfall) under two hydrologic scenarios (dry
and wet weather). The first results were obtained over a period of five
months. Each investigated (Ormes, l’Egoutier and La Corne) outfall
represents an urban runoff source that receives water from runoff
roads, gutters, the irrigation of gardens and other sources of flow over
the Earth’s surface that drains in its catchments and carries it to the
Loire River. In wet weather conditions there is rain water runoff and
an additional input from the roof gutters that have entered the
stormwater system during rainfall. For the comparison the results La
Chilesse is a storm overflow that was selected in our study as a
potential source of waste water which is located before the (WWTP). The comparison of the physical-chemical parameters (total
dissolved solids, turbidity, pH, conductivity, dissolved organic
carbon (DOC), concentration of major cations and anions) together
with the chemical oxygen demand (COD) and biological oxygen
demand (BOD) helped to characterize sources of runoff waters in the
different watersheds. It also helped to highlight the infiltration of
wastewater in some stormwater systems that reject directly in the
Loire River. The values of the conductivity measured in the outflow
of Ormes were always higher than those measured in the other two
outlets. The results showed a temporal variation for the Ormes outfall
of conductivity from 1465 μS cm-1 in the dry weather flow to 650 μS
cm-1 in the wet weather flow and also a spatial variation in the wet
weather flow from 650 μS cm-1 in the Ormes outfall to 281 μS cm-1
in L’Egouttier outfall. The ultimate BOD (BOD28) showed a
significant decrease in La Corne outfall from 181 mg L-1 in the wet
weather flow to 95 mg L-1 in the dry weather flow because of the
nutrient load that was transported by the runoff.
Abstract: Radical technological innovations enable companies
to reach strong market positions and are thus desirable. On the other
hand, the innovation process is related to significant costs and risks.
Hence, the knowledge of the factors that influence success is crucial
for technology driven companies. Taking a previously developed
framework of Critical Success Factors for radical technological
innovations as a reference model, we conducted a structured and
focused literature review of eleven standard books within the field of
technology and innovation management. With this approach we aim
to evaluate, expand, and clarify the set of Critical Success Factors
detailed in this framework. Overall, the set of factors and their
allocation to the main categories of the framework could be
confirmed. However, the factor organizational home is not
emphasized and discussed in most of the reviewed literature. On the
other hand, an additional factor that has not been part of the
framework is described to be important – strategy fit. Furthermore,
the factors strategic alliances and platform strategy appear in the
literature but in a different context compared to the reference model.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.
Abstract: Current study established for EEG signal analysis in
patients with language disorder. Language disorder can be defined as
meaningful delay in the use or understanding of spoken or written
language. The disorder can include the content or meaning of
language, its form, or its use. Here we applied Z-score, power
spectrum, and coherence methods to discriminate the language
disorder data from healthy ones. Power spectrum of each channel in
alpha, beta, gamma, delta, and theta frequency bands was measured.
In addition, intra hemispheric Z-score obtained by scoring algorithm.
Obtained results showed high Z-score and power spectrum in
posterior regions. Therefore, we can conclude that peoples with
language disorder have high brain activity in frontal region of brain
in comparison with healthy peoples. Results showed that high coherence correlates with irregularities
in the ERP and is often found during complex task, whereas low
coherence is often found in pathological conditions. The results of the
Z-score analysis of the brain dynamics showed higher Z-score peak
frequency in delta, theta and beta sub bands of Language Disorder
patients. In this analysis there were activity signs in both hemispheres
and the left-dominant hemisphere was more active than the right.
Abstract: The knitted fabric suffers a deformation in its
dimensions due to stretching and tension factors, transverse and
longitudinal respectively, during the process in rectilinear knitting
machines so it performs a dry relaxation shrinkage procedure and
thermal action of prefixed to obtain stable conditions in the knitting.
This paper presents a dry relaxation shrinkage prediction of Bordeaux
fiber using a feed forward neural network and linear regression
models. Six operational alternatives of shrinkage were predicted. A
comparison of the results was performed finding neural network
models with higher levels of explanation of the variability and
prediction. The presence of different reposes is included. The models
were obtained through a neural toolbox of Matlab and Minitab
software with real data in a knitting company of Southern
Guanajuato. The results allow predicting dry relaxation shrinkage of
each alternative operation.
Abstract: Research has shown that techno-entrepreneurship is
economically significant. Therefore, it is suggested that teaching
techno-entrepreneurship may be important because such programmes
would prepare current and future generations of learners to recognise
and act on high-technology opportunities. Education in technoentrepreneurship
may increase the knowledge of how to start one’s
own enterprise and recognise the technological opportunities for
commercialisation to improve decision-making about starting a new
venture; also it influence decisions about capturing the business
opportunities and turning them into successful ventures. Universities
can play a main role in connecting and networking technoentrepreneurship
students towards a cooperative attitude with real
business practice and industry knowledge. To investigate and answer
whether education for techno-entrepreneurs really helps, this paper
choses a comparison of literature reviews as its method of research.
After reviewing literature related to the impact of technoentrepreneurship
education on self-employment 6 studies which had
similar aim and objective to this paper were. These particular papers
were selected based on a keywords search and as their aim,
objectives, and gaps were close to the current research. In addition,
they were all based on the influence of techno-entrepreneurship
education in self-employment and intention of students to start new
ventures. The findings showed that teaching techno-entrepreneurship
education may have an influence on students’ intention and their
future self-employment, but which courses should be covered and the
duration of programmes, needs further investigation.
Abstract: This paper presents comparative analysis of
photovoltaic systems (PVS) and propose practical techniques to
improve operational efficiency of the PVS. The best engineering and
construction practices for PVS are identified and field oriented
recommendation are made. Comparative analysis of central and
string inverter based, as well as 600 and 1000VDC PVS are
performed. In addition, direct current (DC) and alternating current
(AC) photovoltaic (PV) module based systems are compared.
Comparison shows that 1000V DC String Inverters based PVS is the
best choice.
Abstract: The work reported through this paper is an
experimental work conducted on High Performance Concrete (HPC)
with super plasticizer with the aim to develop some models suitable
for prediction of compressive strength of HPC mixes. In this study,
the effect of varying proportions of fly ash (0% to 50% @ 10%
increment) on compressive strength of high performance concrete has
been evaluated. The mix designs studied were M30, M40 and M50 to
compare the effect of fly ash addition on the properties of these
concrete mixes. In all eighteen concrete mixes that have been
designed, three were conventional concretes for three grades under
discussion and fifteen were HPC with fly ash with varying
percentages of fly ash. The concrete mix designing has been done in
accordance with Indian standard recommended guidelines. All the
concrete mixes have been studied in terms of compressive strength at
7 days, 28 days, 90 days, and 365 days. All the materials used have
been kept same throughout the study to get a perfect comparison of
values of results. The models for compressive strength prediction
have been developed using Linear Regression method (LR), Artificial
Neural Network (ANN) and Leave-One-Out Validation (LOOV)
methods.
Abstract: Lots of motors have been being used in industry.
Therefore many researchers have studied about the failure diagnosis of
motors. In this paper, the effect of measuring environment for
diagnosis of gear fault connected to a motor shaft is studied. The fault
diagnosis is executed through the comparison of normal gear and
abnormal gear. The measured FFT data are compared with the normal
data and analyzed for q-axis current, noise and vibration. For bad and
good environment, the diagnosis results are compared. From these, it
is shown that the bad measuring environment may not be able to detect
exactly the motor gear fault. Therefore it is emphasized that the
measuring environment should be carefully prepared.
Abstract: The McEliece cryptosystem is an asymmetric type of
cryptography based on error correction code. The classical McEliece
used irreducible binary Goppa code which considered unbreakable
until now especially with parameter [1024, 524, and 101], but it is
suffering from large public key matrix which leads to be difficult to
be used practically. In this work Irreducible and Separable Goppa
codes have been introduced. The Irreducible and Separable Goppa
codes used are with flexible parameters and dynamic error vectors. A
Comparison between Separable and Irreducible Goppa code in
McEliece Cryptosystem has been done. For encryption stage, to get
better result for comparison, two types of testing have been chosen;
in the first one the random message is constant while the parameters
of Goppa code have been changed. But for the second test, the
parameters of Goppa code are constant (m=8 and t=10) while the
random message have been changed. The results show that the time
needed to calculate parity check matrix in separable are higher than
the one for irreducible McEliece cryptosystem, which is considered
expected results due to calculate extra parity check matrix in
decryption process for g2(z) in separable type, and the time needed to
execute error locator in decryption stage in separable type is better
than the time needed to calculate it in irreducible type. The proposed
implementation has been done by Visual studio C#.
Abstract: Predicting earnings management is vital for the capital
market participants, financial analysts and managers. The aim of this
research is attempting to respond to this query: Is there a significant
difference between the regression model and neural networks’
models in predicting earnings management, and which one leads to a
superior prediction of it? In approaching this question, a Linear
Regression (LR) model was compared with two neural networks
including Multi-Layer Perceptron (MLP), and Generalized
Regression Neural Network (GRNN). The population of this study
includes 94 listed companies in Tehran Stock Exchange (TSE)
market from 2003 to 2011. After the results of all models were
acquired, ANOVA was exerted to test the hypotheses. In general, the
summary of statistical results showed that the precision of GRNN did
not exhibit a significant difference in comparison with MLP. In
addition, the mean square error of the MLP and GRNN showed a
significant difference with the multi variable LR model. These
findings support the notion of nonlinear behavior of the earnings
management. Therefore, it is more appropriate for capital market
participants to analyze earnings management based upon neural
networks techniques, and not to adopt linear regression models.
Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: Environmental and functional conditions, sometimes,
necessitate the architectural plan of the building to be asymmetric,
and this result in an asymmetric structure. In such cases finding an
optimal pattern for locating the components of lateral load bearing
system, including shear walls, in the building’s plan is desired. In
case of shear wall in addition to the location the shape of the wall
cross-section is also an effective factor. Various types of shear walls
and their proper layout might come effective in better stiffness
distribution and more appropriate seismic response of the building.
Several studies have been conducted in the context of analysis and
design of shear walls; however, few studies have been performed on
making decisions for the location and form of shear walls in multistory
buildings, especially those with irregular plan. In this study, an
attempt has been made to obtain the most reliable seismic behavior of
multi-story reinforced concrete vertically chamfered buildings by
using more appropriate shear walls form and arrangement in 7-, 10-,
12-, and 15-stoy buildings. The considered forms and arrangements
include common rectangular walls and L-, T-, U- and Z-shaped plan,
located as the core or in the outer frames of the building structure.
Comparison of seismic behaviors of the buildings, including
maximum roof displacement and particularly formation of plastic
hinges and their distribution in the buildings’ structures, have been
done based on the results of a series of nonlinear time history
analyses, by using a set of selected earthquake records. Results show
that shear walls with U-shaped cross-section, placed as the building
central core, and also walls with Z-shaped cross-section, placed at the
corners give the building more reliable seismic behavior.
Abstract: The apportionment method is used by many countries, to calculate the distribution of seats in political bodies. For example, this method is used in the United States (U.S.) to distribute house seats proportionally based on the population of the electoral district. Famous apportionment methods include the divisor methods called the Adams Method, Dean Method, Hill Method, Jefferson Method and Webster Method. Sometimes the results from the implementation of these divisor methods are unfair and include errors. Therefore, it is important to examine the optimization of this method by using a bias measurement to figure out precise and fair results. In this research we investigate the bias of divisor methods in the U.S. Houses of Representatives toward large and small states by applying the Stolarsky Mean Method. We compare the bias of the apportionment method by using two famous bias measurements: the Balinski and Young measurement and the Ernst measurement. Both measurements have a formula for large and small states. The Third measurement however, which was created by the researchers, did not factor in the element of large and small states into the formula. All three measurements are compared and the results show that our measurement produces similar results to the other two famous measurements.
Abstract: The importance of this study is to understand how Indonesian military court asserts its jurisdiction over military members who commit general crimes within the Indonesian military judiciary system in comparison to other countries. This research employs a normative-juridical approach in combination with historical and comparative-juridical approaches. The research specification is analytical-descriptive in nature, i.e. describing or outlining the principles, basic concepts, and norms related to military judiciary system, which are further analyzed within the context of implementation and as the inputs for military justice regulation under the Indonesian legal system. Main data used in this research are secondary data, including primary, secondary and tertiary legal sources. The research focuses on secondary data, while primary data are supplementary in nature. The validity of data is checked using multi-methods commonly known as triangulation, i.e. to reflect the efforts to gain an in-depth understanding of phenomena being studied. Here, the military element is kept intact in the judiciary process with due observance of the Military Criminal Justice System and the Military Command Development Principle. The Indonesian military judiciary jurisdiction over military members committing general crimes is based on national legal system and global development while taking into account the structure, composition and position of military forces within the state structure. Jurisdiction is formulated by setting forth the substantive norm of crimes that are military in nature. At the level of adjudication jurisdiction, the military court has a jurisdiction to adjudicate military personnel who commit general offences. At the level of execution jurisdiction, the military court has a jurisdiction to execute the sentence against military members who have been convicted with a final and binding judgement. Military court's jurisdiction needs to be expanded when the country is in the state of war.
Abstract: This paper discusses the question whether a person
diagnosed with dyslexia will necessarily have difficulty in reading
musical notes. The author specifies the characteristics of alphabet
reading in comparison to musical notation reading, and concludes
that there should be no contra-indication for teaching standard music
reading to children with dyslexia if an appropriate process is offered.
This conclusion is based on a long term case study and relies on two
main characteristics of music reading: (1) musical notation system is
a systematic, logical, relative set of symbols written on a staff; and
(2) music reading learning connected with playing a musical
instrument is a multi-sensory activity that combines sight, hearing,
touch, and movement. The paper describes music reading teaching
procedures, using soprano recorders, and provides unique teaching
methods that have been found to be effective for students who were
diagnosed with dyslexia. It provides theoretical explanations in
addition to guidelines for music education practices.
Abstract: A new approach has been developed to estimate the
load share and distribution of worm gear drives, and to calculate the
instantaneous tooth meshing stiffness. In the approach, the worm gear
drive was modelled as a series of spur gear slices, and each slice was
analyzed separately using the well-established formulae of spur gear
loading and stresses. By combining the results obtained for all slices,
the entire envolute worm gear set loading and stressing was obtained. The geometric modelling method presented allows tooth elastic
deformation and tooth root stresses of worm gear drives under
different load conditions to be investigated. Based on the slicing
method introduced in this study, the instantaneous meshing stiffness
and load share are obtained. In comparison with existing methods,
this approach has both good analysis accuracy and less computing
time.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.