Abstract: A numerical study of natural convection heat transfer
in water filled cavity has been examined in 3-Dfor single phase liquid
cooling system by using an array of parallel plate fins mounted to one
wall of a cavity. The heat generated by a heat source represents a
computer CPU with dimensions of 37.5∗37.5mm mounted on
substrate. A cold plate is used as a heat sink installed on the opposite
vertical end of the enclosure. The air flow inside the computer case is
created by an exhaust fan. A turbulent air flow is assumed and k-ε
model is applied. The fins are installed on the substrate to enhance
the heat transfer. The applied power energy range used is between 15
- 40W. In order to determine the thermal behaviour of the cooling
system, the effect of the heat input and the number of the parallel
plate fins are investigated. The results illustrate that as the fin number
increases the maximum heat source temperature decreases. However,
when the fin number increases to critical value the temperature start
to increase due to the fins are too closely spaced and that cause the
obstruction of water flow. The introduction of parallel plate fins
reduces the maximum heat source temperature by 10% compared to
the case without fins. The cooling system maintains the maximum
chip temperature at 64.68°C when the heat input was at 40W that is
much lower than the recommended computer chips limit temperature
of no more than 85°C and hence the performance of the CPU is
enhanced.
Abstract: In this study, we have focused our attention on
combining of molecular imprinting into nanofilms and QCM
nanosensor approaches and producing QCM nanosensor for anti-
CCP, chosen as model protein, using anti-CCP imprinted nanofilms.
The nonimprinted nanosensor was also prepared to evaluate the
selectivity of the imprinted nanosensor. Anti-CCP imprinted QCM
nanosensor was tested for real time detection of anti-CCP from
aqueous solution. The kinetic and affinity studies were determined by
using anti-CCP solutions with different concentrations. The
responses related with mass shifts (%m) and frequency shifts (%f)
were used to evaluate adsorption properties. To show the selectivity
of the anti-CCP imprinted QCM nanosensor, competitive adsorption
of anti-CCP and IgM was investigated. The results indicate that anti-
CCP imprinted QCM nanosensor has higher adsorption capabilities
for anti-CCP than for IgM, due to selective cavities in the polymer
structure.
Abstract: Human motion capture has become one of the major
area of interest in the field of computer vision. Some of the major
application areas that have been rapidly evolving include the
advanced human interfaces, virtual reality and security/surveillance
systems. This study provides a brief overview of the techniques and
applications used for the markerless human motion capture, which
deals with analyzing the human motion in the form of mathematical
formulations. The major contribution of this research is that it
classifies the computer vision based techniques of human motion
capture based on the taxonomy, and then breaks its down into four
systematically different categories of tracking, initialization, pose
estimation and recognition. The detailed descriptions and the
relationships descriptions are given for the techniques of tracking and
pose estimation. The subcategories of each process are further
described. Various hypotheses have been used by the researchers in
this domain are surveyed and the evolution of these techniques have
been explained. It has been concluded in the survey that most
researchers have focused on using the mathematical body models for
the markerless motion capture.
Abstract: With increasingly more mobile health applications
appearing due to the popularity of smartphones, the possibility arises
that these data can be used to improve the medical diagnostic process,
as well as the overall quality of healthcare, while at the same time
lowering costs. However, as of yet there have been no reports of a
successful combination of patient-generated data from smartphones
with data from clinical routine. In this paper we describe how these
two types of data can be combined in a secure way without
modification to hospital information systems, and how they can
together be used in a medical expert system for automatic nutritional
classification and triage.
Abstract: A large amount of data is typically stored in relational
databases (DB). The latter can efficiently handle user queries which
intend to elicit the appropriate information from data sources.
However, direct access and use of this data requires the end users to
have an adequate technical background, while they should also cope
with the internal data structure and values presented. Consequently
the information retrieval is a quite difficult process even for IT or DB
experts, taking into account the limited contributions of relational
databases from the conceptual point of view. Ontologies enable users
to formally describe a domain of knowledge in terms of concepts and
relations among them and hence they can be used for unambiguously
specifying the information captured by the relational database.
However, accessing information residing in a database using
ontologies is feasible, provided that the users are keen on using
semantic web technologies. For enabling users form different
disciplines to retrieve the appropriate data, the design of a Graphical
User Interface is necessary. In this work, we will present an
interactive, ontology-based, semantically enable web tool that can be
used for information retrieval purposes. The tool is totally based on
the ontological representation of underlying database schema while it
provides a user friendly environment through which the users can
graphically form and execute their queries.
Abstract: Environmental impact assessment techniques have
been developed as a result of the worldwide efforts to reduce the
environmental impact of global warming. By using the quantification
method in the construction industry, it is now possible to manage the
greenhouse gas is to systematically evaluate the impact on the
environment over the entire construction process. In particular, the
proportion of greenhouse gas emissions at the production stage of
construction material occupied is high, and efforts are needed in
particular in the construction field.
In this research, intended for concrete products for the construction
materials, by using the LCA method, we compared the results of
environmental impact assessment and carbon emissions of developing
products that have been applied low-carbon technologies compared to
existing products. As a results, by introducing a raw material of
industrial waste, showed carbon reduction. Through a comparison of
the carbon emission reduction effect of low carbon technologies, it is
intended to provide academic data for the evaluation of greenhouse
gases in the construction sector and the development of low carbon
technologies of the future.
Abstract: The purpose of this paper is to examine the hypothesis
explaining the mechanism in the case, where the product is deleted or
reduced the fundamental function of the product through the product
concept changes in the digital camera industry. This paper points out
not owning the fundamental technology might cause the change of the
product concept. Casio could create new competitive factor so that this
paper discusses a possibility of the mechanism of changing the product
concept.
Abstract: Large-scale data stream analysis has become one of
the important business and research priorities lately. Social networks
like Twitter and other micro-blogging platforms hold an enormous
amount of data that is large in volume, velocity and variety.
Extracting valuable information and trends out of these data would
aid in a better understanding and decision-making. Multiple analysis
techniques are deployed for English content. Moreover, one of the
languages that produce a large amount of data over social networks
and is least analyzed is the Arabic language. The proposed paper is a
survey on the research efforts to analyze the Arabic content in
Twitter focusing on the tools and methods used to extract the
sentiments for the Arabic content on Twitter.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: The wear measuring and wear modelling are
fundamental issues in the industrial field, mainly correlated to the
economy and safety. Therefore, there is a need to study the wear
measurements and wear estimation. Pin-on-disc test is the most
common test which is used to study the wear behaviour. In this paper,
the pin-on-disc (AEROTECH UNIDEX 11) is used for the
investigation of the effects of normal load and hardness of material on
the wear under dry and sliding conditions. In the pin-on-disc rig, two
specimens were used; one, a pin is made of steel with a tip, positioned
perpendicular to the disc, where the disc is made of aluminium. The
pin wear and disc wear were measured by using the following
instruments: The Talysurf instrument, a digital microscope, and the
alicona instrument. The Talysurf profilometer was used to measure
the pin/disc wear scar depth, digital microscope was used to measure
the diameter and width of wear scar, and the alicona was used to
measure the pin wear and disc wear. After that, the Archard model,
American Society for Testing and Materials model (ASTM), and
neural network model were used for pin/disc wear modelling.
Simulation results were implemented by using the Matlab program.
This paper focuses on how the alicona can be used for wear
measurements and how the neural network can be used for wear
estimation.
Abstract: Agriculture is the backbone of economy of Pakistan
and cotton is the major agricultural export and supreme source of raw
fiber for our textile industry. To combat severe problems of insect
and weed, combination of three genes namely Cry1Ac, Cry2A and
EPSPS genes was transferred in locally cultivated cotton variety
MNH-786 with the use of Agrobacterium mediated genetic
transformation. The present study focused on the molecular screening
of transgenic cotton plants at T3 generation in order to confirm
integration and expression of all three genes (Cry1Ac, Cry2A and
EPSP synthase) into the cotton genome. Initially, glyphosate spray
assay was used for screening of transgenic cotton plants containing
EPSP synthase gene at T3 generation. Transgenic cotton plants which
were healthy and showed no damage on leaves were selected after 07
days of spray. For molecular analysis of transgenic cotton plants in
the laboratory, the genomic DNA of these transgenic cotton plants
were isolated and subjected to amplification of the three genes. Thus,
seventeen out of twenty (Cry1Ac gene), ten out of twenty (Cry2A
gene) and all twenty (EPSP synthase gene) were produced positive
amplification. On the base of PCR amplification, ten transgenic plant
samples were subjected to protein expression analysis through
ELISA. The results showed that eight out of ten plants were actively
expressing the three transgenes. Real-time PCR was also done to
quantify the mRNA expression levels of Cry1Ac and EPSP synthase
gene. Finally, eight plants were confirmed for the presence and active
expression of all three genes at T3 generation.
Abstract: This article is trying to determine the status of flue gas
that is entering the KWH heat exchanger from combustion chamber
in order to calculate the heat transfer ratio of the heat exchanger.
Combination of measurement, calculation and computer simulation
was used to create a useful way to approximate the heat transfer rate.
The measurements were taken by a number of sensors that are
mounted on the experimental device and by a thermal imaging
camera. The results of the numerical calculation are in a good
correspondence with the real power output of the experimental
device. That result shows that the research has a good direction and
can be used to propose changes in the construction of the heat
exchanger, but still needs enhancements.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: This paper describes an analysis of Yacht Simulator
international trends and also explains about Yacht. The results are
summarized as follows. Attached to the cockpit are sensors that feed
-back information on rudder angle, boat heel angle and mainsheet
tension to the computer. Energy expenditure of the sailor measure
indirectly using expired gas analysis for the measurement of VO2 and
VCO2. At sea course configurations and wind conditions can be preset
to suit any level of sailor from complete beginner to advanced sailor.
Abstract: The air transport impact on environment is more than
ever a limitative obstacle to the aeronautical industry continuous
growth. Over the last decades, considerable effort has been carried
out in order to obtain quieter aircraft solutions, whether by changing
the original design or investigating more silent maneuvers. The
noise propagated by rotating surfaces is one of the most important
sources of annoyance, being present in most aerial vehicles. Bearing
this is mind, CEIIA developed a new computational chain for
noise prediction with in-house software tools to obtain solutions in
relatively short time without using excessive computer resources. This
work is based on the new acoustic tool, which aims to predict the
rotor noise generated during steady and maneuvering flight, making
use of the flexibility of the C language and the advantages of GPU
programming in terms of velocity. The acoustic tool is based in the
Formulation 1A of Farassat, capable of predicting two important
types of noise: the loading and thickness noise. The present work
describes the most important features of the acoustic tool, presenting
its most relevant results and framework analyses for helicopters and
UAV quadrotors.
Abstract: This paper presents a method of hardening the 8051
micro-controller, able to assure reliable operation in the presence of
bit flips caused by radiation. Aiming at avoiding such faults in the
8051 micro-controller, Hamming code protection was used in its
SRAM memory and registers. A VHDL code has been used for this
hamming code protection.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: Estimation of model parameters is necessary to predict
the behavior of a system. Model parameters are estimated using
optimization criteria. Most algorithms use historical data to estimate
model parameters. The known target values (actual) and the output
produced by the model are compared. The differences between the
two form the basis to estimate the parameters. In order to compare
different models developed using the same data different criteria are
used. The data obtained for short scale projects are used here. We
consider software effort estimation problem using radial basis
function network. The accuracy comparison is made using various
existing criteria for one and two predictors. Then, we propose a new
criterion based on linear least squares for evaluation and compared
the results of one and two predictors. We have considered another
data set and evaluated prediction accuracy using the new criterion.
The new criterion is easy to comprehend compared to single statistic.
Although software effort estimation is considered, this method is
applicable for any modeling and prediction.
Abstract: It is important to take security measures to protect
your computer information, reduce identify theft, and prevent from
malicious cyber-attacks. With cyber-attacks on the continuous rise,
people need to understand and learn ways to prevent from these
attacks. Cyber-attack is an important factor to be considered if one is
to be able to protect oneself from malicious attacks. Without proper
security measures, most computer technology would hinder home
users more than such technologies would help. Knowledge of how
cyber-attacks operate and protective steps that can be taken to reduce
chances of its occurrence are key to increasing these security
measures. The purpose of this paper is to inform home users on the
importance of identifying and taking preventive steps to avoid cyberattacks.
Throughout this paper, many aspects of cyber-attacks will be
discuss: what a cyber-attack is, the affects of cyber-attack for home
users, different types of cyber-attacks, methodology to prevent such
attacks; home users can take to fortify security of their computer.
Abstract: The inherent skin patterns created at the joints in the
finger exterior are referred as finger knuckle-print. It is exploited to
identify a person in a unique manner because the finger knuckle print
is greatly affluent in textures. In biometric system, the region of
interest is utilized for the feature extraction algorithm. In this paper,
local and global features are extracted separately. Fast Discrete
Orthonormal Stockwell Transform is exploited to extract the local
features. Global feature is attained by escalating the size of Fast
Discrete Orthonormal Stockwell Transform to infinity. Two features
are fused to increase the recognition accuracy. A matching distance is
calculated for both the features individually. Then two distances are
merged mutually to acquire the final matching distance. The
proposed scheme gives the better performance in terms of equal error
rate and correct recognition rate.