Abstract: Presents a concept for a multidisciplinary process
supporting effective task transitions between different technical
domains during the architectural design stage.
A system configuration challenge is the multifunctional driven
increased solution space. As a consequence, more iteration is needed
to find a global optimum, i.e. a compromise between involved
disciplines without negative impact on development time. Since state
of the art standards like ISO 15288 and VDI 2206 do not provide a
detailed methodology on multidisciplinary design process, higher
uncertainties regarding final specifications arise. This leads to the
need of more detailed and standardized concepts or processes which
could mitigate risks.
The performed work is based on analysis of multidisciplinary
interaction, of modeling and simulation techniques. To demonstrate
and prove the applicability of the presented concept, it is applied to
the design of aircraft high lift systems, in the context of the
engineering disciplines kinematics, actuation, monitoring, installation
and structure design.
Abstract: Sharing the manufacturing facility through remote
operation and monitoring of a machining process is challenge for
effective use the production facility. Several automation tools in term
of hardware and software are necessary for successfully remote
operation of a machine. This paper presents a prototype of workpiece
holding attachment for remote operation of milling process by self
configuration the workpiece setup. The prototype is designed with
mechanism to reorient the work surface into machining spindle
direction with high positioning accuracy. Variety of parts geometry
is hold by attachment to perform single setup machining. Pin type
with array pattern additionally clamps the workpiece surface from
two opposite directions for increasing the machining rigidity.
Optimum pins configuration for conforming the workpiece geometry
with minimum deformation is determined through hybrid algorithms,
Genetic Algorithms (GA) and Particle Swarm Optimization (PSO).
Prototype with intelligent optimization technique enables to hold
several variety of workpiece geometry which is suitable for
machining low of repetitive production in remote operation.
Abstract: In this paper, an improved ant colony optimization
(ACO) algorithm is proposed to enhance the performance of global
optimum search. The strategy of the proposed algorithm has the
capability of fuzzy pheromone updating, adaptive parameter tuning,
and mechanism resetting. The proposed method is utilized to tune the
parameters of the fuzzy controller for a real beam and ball system.
Simulation and experimental results indicate that better performance
can be achieved compared to the conventional ACO algorithms in the
aspect of convergence speed and accuracy.
Abstract: Removal of a reactive dye (Reactive blue 4) by
adsorption utilizing waste aluminium hydroxide sludge as an
adsorbent was investigated. The removal of the dye was optimized
using response surface methodology (RSM). In the RSM
experiments; initial dye concentration, adsorbent concentration and
contact time were critical parameters. RSM experiments were
performed at the range of initial dye concentration 31.82-368.18
mg/L, adsorbent concentration 3.18-36.82 g/L, contact time 15.82-
56.18 h. Optimum initial dye concentration, adsorbent concentration
and contact time were obtained as 108.83 mg/L, 29.36 g/L and 33.57
h respectively. At these conditions, maximum removal of the dye was
obtained as 95%. The experiments were performed at the optimum
conditions to verify these results and the same results were obtained.
Abstract: We present a simulation and realization of a battery
charge regulator (BCR) in microsatellite earth observation. The tests
were performed on battery pack 12volt, capacity 24Ah and the solar array open circuit voltage of 100 volt and optimum power of about
250 watt. The battery charge is made by solar module. The principle is to adapt the output voltage of the solar module to the battery by
using the technique of pulse width modulation (PWM). Among the different techniques of charge battery, we opted for the technique of
the controller ON/OFF is a standard technique and simple, it-s easy to
be board executed validation will be made by simulation "Proteus Isis
Professional software ". The circuit and the program of this prototype
are based on the PIC16F877 microcontroller, a serial interface connecting a PC is also realized, to view and save data and graphics
in real time, for visualization of data and graphs we develop an interface tool “visual basic.net (VB)--.
Abstract: This paper presents the optimum design for a double
stator, cup rotor machine; a novel type of BLDC PM Machine. The optimization approach is divided into two stages: the first stage is
calculating the machine configuration using Matlab, and the second stage is the optimization of the machine using Finite Element
Modeling (FEM). Under the design specifications, the machine
model will be selected from three pole numbers, namely, 8, 10 and 12 with an appropriate slot number. A double stator brushless DC
permanent magnet machine is designed to achieve low cogging torque; high electromagnetic torque and low ripple torque.
Abstract: The study of effect of laser scanning speed on
material efficiency in Ti6Al4V application is very important because unspent powder is not reusable because of high temperature oxygen
pick-up and contamination. This study carried out an extensive study
on the effect of scanning speed on material efficiency by varying the
speed between 0.01 to 0.1m/sec. The samples are wire brushed and
cleaned with acetone after each deposition to remove un-melted
particles from the surface of the deposit. The substrate is weighed before and after deposition. A formula was developed to calculate the
material efficiency and the scanning speed was compared with the
powder efficiency obtained. The results are presented and discussed.
The study revealed that the optimum scanning speed exists for this study at 0.01m/sec, above and below which the powder efficiency
will drop
Abstract: Characterization and evaluation of the activity of Vespa basalis DPP-IV, which expressed in Spodoptera frugiperda 21 cells. The expression of rDPP-IV was confirmed by SDS–PAGE, Western blot analyses, LC-MS/MS and measurement of its peptidase specificity. One-step purification by Ni-NTA affinity chromatography and the total amount of rDPP-IV recovered was approximately 6.4mg per liter from infected culture medium; an equivalent amount would be produced by 1x109 infected Sf21 insect cells. Through the affinity purification led to highly stable rDPP-IV enzyme was recovered and with significant peptidase activity. The rDPP-IV exhibited classical Michaelis–Menten kinetics, with kcat/Km in the range of 10-500 mM-1×S-1 for the five synthetic substrates and optimum substrate is Ala-Pro-pNA. As expected in inhibition assay, the enzymatic activity of rDPP-IV was significantly reduced by 80 or 60% in the presence of sitagliptin (a DPP-IV inhibitor) or PMSF (a serine protease inhibitor), but was not apparently affected by iodoacetamide (a cysteine protease inhibitor).
Abstract: Design and evaluation of reciprocating compressors
should include a pulsation study. The object is to ensure that
predicted pulsation levels meet guidelines to limit vibration, shaking
forces, noise, associated pressure drops, horsepower losses and
fabrication cost and time to acceptable levels. This paper explains
procedures and recommendations to select and size pulsation
suppression devices to obtain optimum arrangement in terms of
pulsation, vibration, shaking forces, performance, reliability, safety,
operation, maintenance and commercial conditions. Model and
advanced formulations for pulsation study are presented. The effect
of the full fluid dynamic model on the prediction of pulsation waves
and resulting frequency spectrum distributions are discussed.
Advanced and optimum methods of controlling pulsations are
highlighted. Useful recommendations and guidelines for pulsation
control, piping pulsation analysis, pulsation vessel design, shaking
forces, low pressure drop orifices, pulsation study report and devices
to mitigate pulsation and shaking problems are discussed.
Abstract: The numerical simulation of the slip effect via
vicoelastic fluid for 4:1 contraction problem is investigated with
regard to kinematic behaviors of streamlines and stress tensor by
models of the Navier-Stokes and Oldroyd-B equations. Twodimensional
spatial reference system of incompressible creeping flow
with and without slip velocity is determined and the finite element
method of a semi-implicit Taylor-Galerkin pressure-correction is
applied to compute the problem of this Cartesian coordinate system
including the schemes of velocity gradient recovery method and the
streamline-Upwind / Petrov-Galerkin procedure. The slip effect at
channel wall is added to calculate after each time step in order to
intend the alteration of flow path. The result of stress values and the
vortices are reduced by the optimum slip coefficient of 0.1 with near
the outcome of analytical solution.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: This study shows the effect of carbon towards
molybdenum carbide alloy when exposed to Microwave. This
technique is also known as Microwave Induced Alloying (MIA) for
the preparation of molybdenum carbide. In this study ammonium
heptamolybdate solution and carbon black powder were
heterogeneously mixed and exposed to microwave irradiation for 2
minutes. The effect on amount of carbon towards the produced alloy
on morphological and oxidation states changes during microwave is
presented. In this experiment, it is expected carbon act as a reducing
agent with the ratio 2:7 molybdenum to carbon as the optimum for
the production of molybdenum carbide alloy. All the morphological
transformations and changes in this experiment were followed and
characterized using X-Ray Diffraction and FESEM.
Abstract: In this paper, determining the optimal proportionalintegral-
derivative (PID) controller gains of an single-area load
frequency control (LFC) system using genetic algorithm (GA) is
presented. The LFC is notoriously difficult to control optimally using
conventionally tuning a PID controller because the system parameters
are constantly changing. It is for this reason the GA as tuning strategy
was applied. The simulation has been conducted in MATLAB
Simulink package for single area power system. the simulation results
shows the effectiveness performance of under various disturbance.
Abstract: Tool wear and surface roughness prediction plays a
significant role in machining industry for proper planning and control
of machining parameters and optimization of cutting conditions. This
paper deals with developing an artificial neural network (ANN)
model as a function of cutting parameters in turning steel under
minimum quantity lubrication (MQL). A feed-forward
backpropagation network with twenty five hidden neurons has been
selected as the optimum network. The co-efficient of determination
(R2) between model predictions and experimental values are 0.9915,
0.9906, 0.9761 and 0.9627 in terms of VB, VM, VS and Ra
respectively. The results imply that the model can be used easily to
forecast tool wear and surface roughness in response to cutting
parameters.
Abstract: A new chelating resin is prepared by coupling
Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer.
The resulting sorbent has been characterized by FT-IR, elemental
analysis and thermogravimetric analysis (TGA) and studied for
preconcentrating of Cu (II) using flame atomic absorption
spectrometry (FAAS) for metal monitoring. The optimum pH value
for sorption of the copper ions was 6.5. The resin was subjected to
evaluation through batch binding of mentioned metal ion.
Quantitative desorption occurs instantaneously with 0.5 M HNO3.
The sorption capacity was found 4.8 mmol.g-1 of resin for Cu (II) in
the aqueous solution. The chelating resin can be reused for 10 cycles
of sorption-desorption without any significant change in sorption
capacity. A recovery of 99% was obtained the metal ions with 0.5 M
HNO3 as eluting agent. The method was applied for metal ions
determination from industrial waste water sample.
Abstract: In the way of growing and developing firms especially
high-tech firms, on many occasions manager of firm is mainly involved in solving problems of his business and decision making about executive activities of the firm, while besides executive
measures, attention to planning of firm's success and growth way and
application of long experience and sagacity in designing business model are vital and necessary success in a business is achieved as a
result of different factors, one of the most important of them is designing and performing an optimal business model at the beginning
of the firm's work. This model is determining the limit of profitability
achieved by innovation and gained value added. Therefore, business
model is the process of connecting innovation environment and
technology with economic environment and business and is important
for succeeding modern businesses considering their traits.
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: A numerical analysis of wave and hydrodynamic models
is used to investigate the influence of WAve and Storm Surge
(WASS) in the regional and coastal zones. The numerical analyzed
system consists of the WAve Model Cycle 4 (WAMC4) and the
Princeton Ocean Model (POM) which used to solve the energy
balance and primitive equations respectively. The results of both
models presented the incorporated surface wave in the regional
zone affected the coastal storm surge zone. Specifically, the results
indicated that the WASS generally under the approximation is not
only the peak surge but also the coastal water level drop which
can also cause substantial impact on the coastal environment. The
wave–induced surface stress affected the storm surge can significantly
improve storm surge prediction. Finally, the calibration of wave
module according to the minimum error of the significant wave height
(Hs) is not necessarily result in the optimum wave module in the
WASS analyzed system for the WASS prediction.
Abstract: The aim of this study is to compare the effect of the ultrasonic pre treatment on the removal of heavy metals (Iron, Zinc and Copper) from Acid Mine Drainage (AMD) by Denver Cell flotation. Synthetic AMD and individual metal solutions are used in the initial experiments to optimise the process conditions for real AMD. Three different process methods, ultrasound treatment followed by Denver flotation cell, Denver flotation cell alone and ultrasonic treatments run simultaneously with the Denver flotation cell were tested for every sample. Precipitation of the metal solutions by using sodium hydroxide (NaOH) and application of the optimum frother dosage followed by flotation significantly reduced the metal content of the AMD.