Abstract: This paper describes new computer vision algorithms
that have been developed to track moving objects as part of a
long-term study into the design of (semi-)autonomous vehicles. We
present the results of a study to exploit variable kernels for tracking in
video sequences. The basis of our work is the mean shift
object-tracking algorithm; for a moving target, it is usual to define a
rectangular target window in an initial frame, and then process the data
within that window to separate the tracked object from the background
by the mean shift segmentation algorithm. Rather than use the
standard, Epanechnikov kernel, we have used a kernel weighted by the
Chamfer distance transform to improve the accuracy of target
representation and localization, minimising the distance between the
two distributions in RGB color space using the Bhattacharyya
coefficient. Experimental results show the improved tracking
capability and versatility of the algorithm in comparison with results
using the standard kernel. These algorithms are incorporated as part of
a robot test-bed architecture which has been used to demonstrate their
effectiveness.
Abstract: Model-based approaches have been applied successfully
to a wide range of tasks such as specification, simulation, testing, and
diagnosis. But one bottleneck often prevents the introduction of these
ideas: Manual modeling is a non-trivial, time-consuming task.
Automatically deriving models by observing and analyzing running
systems is one possible way to amend this bottleneck. To
derive a model automatically, some a-priori knowledge about the
model structure–i.e. about the system–must exist. Such a model
formalism would be used as follows: (i) By observing the network
traffic, a model of the long-term system behavior could be generated
automatically, (ii) Test vectors can be generated from the model,
(iii) While the system is running, the model could be used to diagnose
non-normal system behavior.
The main contribution of this paper is the introduction of a model
formalism called 'probabilistic regression automaton' suitable for the
tasks mentioned above.
Abstract: The presence of cold air with the convergent
topography of the Lut valley over the valley-s sloping terrain can
generate Low Level Jets (LLJ). Moreover, the valley-parallel
pressure gradients and northerly LLJ are produced as a result of the
large-scale processes. In the numerical study the regional MM5
model was run leading to achieve an appropriate dynamical analysis
of flows in the region for summer and winter. The results of this
study show the presence of summer synoptical systems cause the
formation of north-south pressure gradients in the valley which could
be led to the blowing of winds with the velocity more than 14 ms-1
and vulnerable dust and wind storms lasting more than 120 days.
Whereas the presence of cold air masses in the region in winter,
cause the average speed of LLJs decrease. In this time downslope
flows are noticeable in creating the night LLJs.
Abstract: An integrated Artificial Neural Network- Particle Swarm Optimization (PSO) is presented for analyzing global electricity consumption. To aim this purpose, following steps are done: STEP 1: in the first step, PSO is applied in order to determine world-s oil, natural gas, coal and primary energy demand equations based on socio-economic indicators. World-s population, Gross domestic product (GDP), oil trade movement and natural gas trade movement are used as socio-economic indicators in this study. For each socio-economic indicator, a feed-forward back propagation artificial neural network is trained and projected for future time domain. STEP 2: in the second step, global electricity consumption is projected based on the oil, natural gas, coal and primary energy consumption using PSO. global electricity consumption is forecasted up to year 2040.
Abstract: Ethanol has been known for a long time, being
perhaps the oldest product obtained through traditional biotechnology
fermentation. Agriculture waste as substrate in fermentation is vastly
discussed as alternative to replace edible food and utilization of
organic material. Pineapple peel, highly potential source as substrate
is a by-product of the pineapple processing industry. Bio-ethanol
from pineapple (Ananas comosus) peel extract was carried out by
controlling fermentation without any treatment. Saccharomyces
ellipsoides was used as inoculum in this fermentation process as it is
naturally found at the pineapple skin. In this study, the capability of
Response Surface Methodology (RSM) for optimization of ethanol
production from pineapple peel extract using Saccharomyces
ellipsoideus in batch fermentation process was investigated. Effect of
five test variables in a defined range of inoculum concentration 6-
14% (v/v), pH (4.0-6.0), sugar concentration (14-22°Brix),
temperature (24-32°C) and time of incubation (30-54 hrs) on the
ethanol production were evaluated. Data obtained from experiment
were analyzed with RSM of MINITAB Software (Version 15)
whereby optimum ethanol concentration of 8.637% (v/v) was
determined. The optimum condition of 14% (v/v) inoculum
concentration, pH 6, 22°Brix, 26°C and 30hours of incubation. The
significant regression equation or model at the 5% level with
correlation value of 99.96% was also obtained.
Abstract: The main goal of this paper is to establish a
methodology for testing and optimizing GPRS performance over
Libya GSM network as well as to propose a suitable optimization
technique to improve performance. Some measurements of
download, upload, throughput, round-trip time, reliability, handover,
security enhancement and packet loss over a GPRS access network
were carried out. Measured values are compared to the theoretical
values that could be calculated beforehand. This data should be
processed and delivered by the server across the wireless network to
the client. The client on the fly takes those pieces of the data and
process immediately. Also, we illustrate the results by describing the
main parameters that affect the quality of service. Finally, Libya-s
two mobile operators, Libyana Mobile Phone and Al-Madar al-
Jadeed Company are selected as a case study to validate our
methodology.
Abstract: Positron emission particle tracking (PEPT) is a
technique in which a single radioactive tracer particle can be
accurately tracked as it moves. A limitation of PET is that in order to
reconstruct a tomographic image it is necessary to acquire a large
volume of data (millions of events), so it is difficult to study rapidly
changing systems. By considering this fact, PEPT is a very fast
process compared with PET.
In PEPT detecting both photons defines a line and the annihilation
is assumed to have occurred somewhere along this line. The location
of the tracer can be determined to within a few mm from coincident
detection of a small number of pairs of back-to-back gamma rays and
using triangulation. This can be achieved many times per second and
the track of a moving particle can be reliably followed. This
technique was invented at the University of Birmingham [1].
The attempt in PEPT is not to form an image of the tracer particle
but simply to determine its location with time. If this tracer is
followed for a long enough period within a closed, circulating system
it explores all possible types of motion.
The application of PEPT to industrial process systems carried out
at the University of Birmingham is categorized in two subjects: the
behaviour of granular materials and viscous fluids. Granular
materials are processed in industry for example in the manufacture of
pharmaceuticals, ceramics, food, polymers and PEPT has been used
in a number of ways to study the behaviour of these systems [2].
PEPT allows the possibility of tracking a single particle within the
bed [3]. Also PEPT has been used for studying systems such as: fluid
flow, viscous fluids in mixers [4], using a neutrally-buoyant tracer
particle [5].
Abstract: Social, culture and artistic status of a society in
various historical eras is affected by numerous, and sometimes
imposed, factors that better understanding requires analysis of such
conditions. Throughout history Iran has been involved with
determining and significant events that examining each of these
events can improve the understanding of social conditions of this
country in the intended time. Mongolian conquest of Iran is one of
most significant events in the history of Iran with consequences that
never left Iranian societies. During this tragic invasion and
subsequent devastating wars, which led to establishment of Ilkhanate
dynasty, numerous cultural and artistic changes occurred both in
Mongolian conquerors and Iranian society. This study examines these
changes with a glimpse towards art and architecture as important part
of cultural aspects and social communication.
Abstract: The fuzzy technique is an operator introduced in order
to simulate at a mathematical level the compensatory behavior in
process of decision making or subjective evaluation. The following
paper introduces such operators on hand of computer vision
application.
In this paper a novel method based on fuzzy logic reasoning
strategy is proposed for edge detection in digital images without
determining the threshold value. The proposed approach begins by
segmenting the images into regions using floating 3x3 binary matrix.
The edge pixels are mapped to a range of values distinct from each
other. The robustness of the proposed method results for different
captured images are compared to those obtained with the linear Sobel
operator. It is gave a permanent effect in the lines smoothness and
straightness for the straight lines and good roundness for the curved
lines. In the same time the corners get sharper and can be defined
easily.
Abstract: The aim of this paper is to emphasize and alleviate the effect of phase noise due to imperfect local oscillators on the performances of a Multi-Carrier CDMA system. After the cancellation of Common Phase Error (CPE), an iterative approach is introduced which iteratively estimates Inter-Carrier Interference (ICI) components in the frequency domain and cancels their contribution in the time domain. Simulation are conducted in order to investigate the achievable performances for several parameters, such as the spreading factor, the modulation order, the phase noise power and the transmission Signal-to-Noise Ratio.
Abstract: The production of activated carbon from low or zero cost of agricultural by-products or wastes has received great attention from academics and practitioners due to its economic and environmental benefits. In the production of bamboo furniture, a significant amount of bamboo waste is inevitably generated. Therefore, this research aimed to prepare activated carbons from bamboo furniture waste by chemical (KOH) activation and determine their properties and adsorption capacities for water treatment. The influence of carbonization time on the properties and adsorption capacities of activated carbons was also investigated. The finding showed that the bamboo-derived activated carbons had microporous characteristics. They exhibited high tendency for the reduction of impurities present in effluent water. Their adsorption capacities were comparable to the adsorption capacity of a commercial activated carbon regarding to the reduction in COD, TDS and turbidity of the effluent water.
Abstract: An electronic portal image device (EPID) has become
a method of patient-specific IMRT dose verification for radiotherapy.
Research studies have focused on pre and post-treatment verification,
however, there are currently no interventional procedures using EPID
dosimetry that measure the dose in real time as a mechanism to
ensure that overdoses do not occur and underdoses are detected as
soon as is practically possible. As a result, an EPID-based real time
dose verification system for dynamic IMRT was developed and was
implemented with MATLAB/Simulink. The EPID image acquisition
was set to continuous acquisition mode at 1.4 images per second. The
system defined the time constraint gap, or execution gap at the image
acquisition time, so that every calculation must be completed before
the next image capture is completed. In addition, the
Abstract: The last years have seen an increasing use of image analysis techniques in the field of biomedical imaging, in particular in microscopic imaging. The basic step for most of the image analysis techniques relies on a background image free of objects of interest, whether they are cells or histological samples, to perform further analysis, such as segmentation or mosaicing. Commonly, this image consists of an empty field acquired in advance. However, many times achieving an empty field could not be feasible. Or else, this could be different from the background region of the sample really being studied, because of the interaction with the organic matter. At last, it could be expensive, for instance in case of live cell analyses. We propose a non parametric and general purpose approach where the background is built automatically stemming from a sequence of images containing even objects of interest. The amount of area, in each image, free of objects just affects the overall speed to obtain the background. Experiments with different kinds of microscopic images prove the effectiveness of our approach.
Abstract: The purpose of this study was to investigate the
response of the newly released Gafchromic HD-V2 film for alpha
particle of 5.5 MeV. Gafchromic HD-V2 was exposed to alpha
particles of energy 5 MeV from 241Am for different durations. Then
the films were scanned with a flatbed scanner. The dose response
curve up to 2200 Gy has been achieved. The film’s reproducibility
and sensitivity were evaluated. The results obtained show that the net
optical density increases almost exponentially with the increase in the
exposure time, and it becomes saturated after prolonged exposure
times. The red channel shows the highest sensitivity, with a value of
4 x 10-3 Gy-1 at netOD of 0.4. The inter-film reproducibility was
measured and the relative uncertainty found was 1.7 %, 2.1 % and 2.3
% for grey, red and green channels, respectively.
Abstract: In this paper, we propose a novel concept of relative
distance measurement using Stereo Vision Technology and discuss
its implementation on a FPGA based real-time image processor. We
capture two images using two CCD cameras and compare them.
Disparity is calculated for each pixel using a real time dense disparity
calculation algorithm. This algorithm is based on the concept of
indexed histogram for matching. Disparity being inversely
proportional to distance (Proved Later), we can thus get the relative
distances of objects in front of the camera. The output is displayed on
a TV screen in the form of a depth image (optionally using pseudo
colors). This system works in real time on a full PAL frame rate (720
x 576 active pixels @ 25 fps).
Abstract: The objective of this paper is to compare the time
specification performance between conventional controller PID and
modern controller SMC for an inverted pendulum system. The goal is
to determine which control strategy delivers better performance with
respect to pendulum-s angle and cart-s position. The inverted
pendulum represents a challenging control problem, which
continually moves toward an uncontrolled state. Two controllers are
presented such as Sliding Mode Control (SMC) and Proportional-
Integral-Derivatives (PID) controllers for controlling the highly
nonlinear system of inverted pendulum model. Simulation study has
been done in Matlab Mfile and simulink environment shows that both
controllers are capable to control multi output inverted pendulum
system successfully. The result shows that Sliding Mode Control
(SMC) produced better response compared to PID control strategies
and the responses are presented in time domain with the details
analysis.
Abstract: This paper describes vibration analysis using the finite
element method for a small earphone, especially for the diaphragm
shape with a low-rigidity. The viscoelastic diaphragm is supported by
multiple nonlinear concentrated springs with linear hysteresis
damping. The restoring forces of the nonlinear springs have cubic
nonlinearity. The finite elements for the nonlinear springs with
hysteresis are expressed and are connected to the diaphragm that is
modeled by linear solid finite elements in consideration of a complex
modulus of elasticity. Further, the discretized equations in physical
coordinates are transformed into the nonlinear ordinary coupled
equations using normal coordinates corresponding to the linear natural
modes. We computed the nonlinear stationary and non-stationary
responses due to the internal resonance between modes with large
amplitude in the nonlinear springs and elastic modes in the diaphragm.
The non-stationary motions are confirmed as the chaos due to the
maximum Lyapunov exponents with a positive number. From the time
histories of the deformation distribution in the chaotic vibration, we
identified nonlinear modal couplings.
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: This paper presented a proposed design for
transcutaneous inductive powering links. The design used to transfer
power and data to the implanted devices such as implanted
Microsystems to stimulate and monitoring the nerves and muscles.
The system operated with low band frequency 13.56 MHZ according
to industrial- scientific – medical (ISM) band to avoid the tissue
heating. For external part, the modulation index is 13 % and the
modulation rate 7.3% with data rate 1 Mbit/s assuming Tbit=1us. The
system has been designed using 0.35-μm fabricated CMOS
technology. The mathematical model is given and the design is
simulated using OrCAD P Spice 16.2 software tool and for real-time
simulation the electronic workbench MULISIM 11 has been used.
The novel circular plane (pancake) coils was simulated using
ANSOFT- HFss software.
Abstract: This paper describes a UDP over IP based, server-oriented redundant host configuration protocol (RHCP) that can be used by collaborating embedded systems in an ad-hoc network to acquire a dynamic IP address. The service is provided by a single network device at a time and will be dynamically reassigned to one of the other network clients if the primary provider fails. The protocol also allows all participating clients to monitor the dynamic makeup of the network over time. So far the algorithm has been implemented and tested on an 8-bit embedded system architecture with a 10Mbit Ethernet interface.