Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: Adhesion strength of exterior or interior coating of
steel pipes is too important. Increasing of coating adhesion on
surfaces can increase the life time of coating, safety factor of
transmitting line pipe and decreasing the rate of corrosion and costs.
Preparation of steel pipe surfaces before doing the coating process is
done by shot and grit blasting. This is a mechanical way to do it.
Some effective parameters on that process, are particle size of
abrasives, distance to surface, rate of abrasive flow, abrasive physical
properties, shapes, selection of abrasive, kind of machine and its
power, standard of surface cleanness degree, roughness, time of
blasting and weather humidity. This search intended to find some
better conditions which improve the surface preparation, adhesion
strength and corrosion resistance of coating. So, this paper has
studied the effect of varying abrasive flow rate, changing the
abrasive particle size, time of surface blasting on steel surface
roughness and over blasting on it by using the centrifugal blasting
machine. After preparation of numbers of steel samples (according to
API 5L X52) and applying epoxy powder coating on them, to
compare strength adhesion of coating by Pull-Off test. The results
have shown that, increasing the abrasive particles size and flow rate,
can increase the steel surface roughness and coating adhesion
strength but increasing the blasting time can do surface over blasting
and increasing surface temperature and hardness too, change,
decreasing steel surface roughness and coating adhesion strength.
Abstract: Guard channels improve the probability of successful
handoffs by reserving a number of channels exclusively for handoffs.
This concept has the risk of underutilization of radio spectrum due to
the fact that fewer channels are granted to originating calls even if
these guard channels are not always used, when originating calls are
starving for the want of channels. The penalty is the reduction of
total carried traffic. The optimum number of guard channels can help
reduce this problem. This paper presents fuzzy logic based guard
channel scheme wherein guard channels are reorganized on the basis
of traffic density, so that guard channels are provided on need basis.
This will help in incorporating more originating calls and hence high
throughput of the radio spectrum
Abstract: In this work, we consider the number of integer solutions
of Diophantine equation D : y2 - 2yx - 3 = 0 over Z and
also over finite fields Fp for primes p ≥ 5. Later we determine the
number of rational points on curves Ep : y2 = Pp(x) = yp
1 + yp
2
over Fp, where y1 and y2 are the roots of D. Also we give a formula
for the sum of x- and y-coordinates of all rational points (x, y) on
Ep over Fp.
Abstract: Nurses in an Armed Force Hospital (AFH) expose to stronger stress than those in a civil hospital, especially in an emergency department (ED). Ironically, stresses of these nurses received few if any attention in academic research in the past. This study collects 227 samples from the emergency departments of four armed force hospitals in central and southern Taiwan. The research indicates that the top five stressors are a massive casualty event, delayed physician support, overloads of routine work, overloads of assignments, and annoying paper work. Excessive work loading was found to be the primary source of stress. Nurses who were perceived to have greater stress levels were more inclined to deploy emotion-oriented approaches and more likely to seek job rotations. Professional stressors and problem-oriented approaches were positively correlated. Unlike other local studies, this study concludes that the excessive work-loading is more stressful in an AFH.
Abstract: This paper presents a novel method for data hiding based on neighborhood pixels information to calculate the number of bits that can be used for substitution and modified Least Significant Bits technique for data embedding. The modified solution is independent of the nature of the data to be hidden and gives correct results along with un-noticeable image degradation. The technique, to find the number of bits that can be used for data hiding, uses the green component of the image as it is less sensitive to human eye and thus it is totally impossible for human eye to predict whether the image is encrypted or not. The application further encrypts the data using a custom designed algorithm before embedding bits into image for further security. The overall process consists of three main modules namely embedding, encryption and extraction cm.
Abstract: According to the density of the chips, designers are
trying to put so any facilities of computational and storage on single
chips. Along with the complexity of computational and storage
circuits, the designing, testing and debugging become more and more
complex and expensive. So, hardware design will be built by using
very high speed hardware description language, which is more
efficient and cost effective. This paper will focus on the
implementation of 32-bit ALU design based on Verilog hardware
description language. Adder and subtracter operate correctly on both
unsigned and positive numbers. In ALU, addition takes most of the
time if it uses the ripple-carry adder. The general strategy for
designing fast adders is to reduce the time required to form carry
signals. Adders that use this principle are called carry look- ahead
adder. The carry look-ahead adder is to be designed with combination
of 4-bit adders. The syntax of Verilog HDL is similar to the C
programming language. This paper proposes a unified approach to
ALU design in which both simulation and formal verification can
co-exist.
Abstract: The group mutual exclusion (GME) problem is an
interesting generalization of the mutual exclusion problem. Several
solutions of the GME problem have been proposed for message
passing distributed systems. However, none of these solutions is
suitable for real time distributed systems. In this paper, we propose a
token-based distributed algorithms for the GME problem in soft real
time distributed systems. The algorithm uses the concepts of priority
queue, dynamic request set and the process state. The algorithm uses
first come first serve approach in selecting the next session type
between the same priority levels and satisfies the concurrent
occupancy property. The algorithm allows all n processors to be
inside their CS provided they request for the same session. The
performance analysis and correctness proof of the algorithm has also
been included in the paper.
Abstract: The purpose of this study was to explore the correlation
between leisure participation and perceived wellness, with the students
of a nursing college in southern Taiwan as the subjects. One thousand
six hundred and ninety-six (1,696) surveys were sent, and 1,408
surveys were received for an 83.02% valid response rate. Using
canonical correlation analysis to analyze the data, the results showed
that the linear combination of the two sets of variable produces five
significant canonical variates. Out of the five canonical variates, only
the first has sufficient explanatory power. The canonical correlation
coefficient of first canonical variate is 0.660. This indicated that
leisure participation and perceived wellness are significantly
correlated.
Abstract: Borate minerals have attracted considerable attention in the past years due to their structural chemistry and mechanical properties in several industries. Recently, increasing attention has been paid to the use of; synthetically produced magnesium borates as catalysts reinforcing material for plastics, the conversion of hydrocarbons, electro-conductive treating agent, anti-wear and anti-corrosion materials. Magnesium borates can be synthesized by several methods such as; hydrothermal and solid-state (thermal) processes. In this study the hydrothermal production method was applied at the modest temperature of 80C along with convenient crystal growth. Using MgCl2.6H2O, H3BO3, and NaOH as starting materials, 30, 60, 120, 240 minutes of reaction times were studied. After all, the crystal structure and the morphology of the products were examined by X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR). As a result the forms of Admontite and Mcallisterite minerals were synthesized.
Abstract: This paper presents an improved variable ordering method to obtain the minimum number of nodes in Reduced Ordered Binary Decision Diagrams (ROBDD). The proposed method uses the graph topology to find the best variable ordering. Therefore the input Boolean function is converted to a unidirectional graph. Three levels of graph parameters are used to increase the probability of having a good variable ordering. The initial level uses the total number of nodes (NN) in all the paths, the total number of paths (NP) and the maximum number of nodes among all paths (MNNAP). The second and third levels use two extra parameters: The shortest path among two variables (SP) and the sum of shortest path from one variable to all the other variables (SSP). A permutation of the graph parameters is performed at each level for each variable order and the number of nodes is recorded. Experimental results are promising; the proposed method is found to be more effective in finding the variable ordering for the majority of benchmark circuits.
Abstract: Stress analysis of functionally graded composite plates
composed of ceramic, functionally graded material and metal layers is
investigated using 3-D finite element method. In FGM layer, material
properties are assumed to be varied continuously in the thickness
direction according to a simple power law distribution in terms of the
volume fraction of a ceramic and metal. The 3-D finite element model
is adopted by using an 18-node solid element to analyze more
accurately the variation of material properties in the thickness
direction. Numerical results are compared for three types of materials.
In the analysis, the tensile and the compressive stresses are
summarized for various FGM thickness ratios, volume fraction
distributions, geometric parameters and mechanical loads.
Abstract: In this paper, Zinc Oxide (ZnO) thin films are deposited on glass substrate by sol-gel method. The ZnO thin films with well defined orientation were acquired by spin coating of zinc acetate dehydrate monoethanolamine (MEA), de-ionized water and isopropanol alcohol. These films were pre-heated at 275°C for 10 min and then annealed at 350°C, 450°C and 550°C for 80 min. The effect of annealing temperature and different thickness on structure and surface morphology of the thin films were verified by Atomic Force Microscopy (AFM). It was found that there was a significant effect of annealing temperature on the structural parameters of the films such as roughness exponent, fractal dimension and interface width. Thin films also were characterizied by X-ray Diffractometery (XRD) method. XRD analysis revealed that the annealed ZnO thin films consist of single phase ZnO with wurtzite structure and show the c-axis grain orientation. Increasing annealing temperature increased the crystallite size and the c-axis orientation of the film after 450°C. Also In this study, ZnO thin films in different thickness have been prepared by sol-gel method on the glass substrate at room temperature. The thicknesses of films are 100, 150 and 250 nm. Using fractal analysis, morphological characteristics of surface films thickness in amorphous state were investigated. The results show that with increasing thickness, surface roughness (RMS) and lateral correlation length (ξ) are decreased. Also, the roughness exponent (α) and growth exponent (β) were determined to be 0.74±0.02 and 0.11±0.02, respectively.
Abstract: The Automatic Speech Recognition (ASR) applied to
Arabic language is a challenging task. This is mainly related to the
language specificities which make the researchers facing multiple
difficulties such as the insufficient linguistic resources and the very
limited number of available transcribed Arabic speech corpora. In
this paper, we are interested in the development of a HMM-based
ASR system for Standard Arabic (SA) language. Our fundamental
research goal is to select the most appropriate acoustic parameters
describing each audio frame, acoustic models and speech recognition
unit. To achieve this purpose, we analyze the effect of varying frame
windowing (size and period), acoustic parameter number resulting
from features extraction methods traditionally used in ASR, speech
recognition unit, Gaussian number per HMM state and number of
embedded re-estimations of the Baum-Welch Algorithm. To evaluate
the proposed ASR system, a multi-speaker SA connected-digits
corpus is collected, transcribed and used throughout all experiments.
A further evaluation is conducted on a speaker-independent continue
SA speech corpus. The phonemes recognition rate is 94.02% which is
relatively high when comparing it with another ASR system
evaluated on the same corpus.
Abstract: This paper proposes a novel feature extraction method,
based on Discrete Wavelet Transform (DWT) and K-L Seperability
(KLS), for the classification of Functional Data (FD). This method
combines the decorrelation and reduction property of DWT and the
additive independence property of KLS, which is helpful to extraction
classification features of FD. It is an advanced approach of the
popular wavelet based shrinkage method for functional data reduction
and classification. A theory analysis is given in the paper to prove the
consistent convergence property, and a simulation study is also done
to compare the proposed method with the former shrinkage ones. The
experiment results show that this method has advantages in improving
classification efficiency, precision and robustness.
Abstract: There was a high rate of corrosion in Pyrolysis
Gasoline Hydrogenation (PGH) unit of Arak Petrochemical Company
(ARPC), and it caused some operational problem in this plant. A
commercial chemical had been used as anti-corrosion in the
depentanizer column overhead in order to control the corrosion rate.
Injection of commercial corrosion inhibitor caused some
operational problems such as fouling in some heat exchangers. It was
proposed to replace this commercial material with another more
effective trouble free, and well-known additive by R&D and
operation specialists.
At first, the system was simulated by commercial simulation
software in electrolytic system to specify low pH points inside the
plant. After a very comprehensive study of the situation and technical
investigations ,ammonia / monoethanol amine solution was proposed
as neutralizer or corrosion inhibitor to be injected in a suitable point
of the plant. For this purpose, the depentanizer column and its
accessories system was simulated again in case of this solution
injection.
According to the simulation results, injection of new anticorrosion
substance has no any side effect on C5 cut product and
operating conditions of the column. The corrosion rate will be
cotrolled, if the pH remains at the range of 6.5 to 8 . Aactual plant
test run was also carried out by injection of ammonia / monoethanol
amine solution at the rate of 0.6 Kg/hr and the results of iron content
of water samples and corrosion test coupons confirmed the
simulation results.
Now, ammonia / monoethanol amine solution is injected to a
suitable pint inside the plant and corrosion rate has decreased
significantly.
Abstract: This paper deals with a power-conscious ANDEXOR- Inverter type logic implementation for a complex class of Boolean functions, namely Achilles- heel functions. Different variants of the above function class have been considered viz. positive, negative and pure horn for analysis and simulation purposes. The proposed realization is compared with the decomposed implementation corresponding to an existing standard AND-EXOR logic minimizer; both result in Boolean networks with good testability attribute. It could be noted that an AND-OR-EXOR type logic network does not exist for the positive phase of this unique class of logic function. Experimental results report significant savings in all the power consumption components for designs based on standard cells pertaining to a 130nm UMC CMOS process The simulations have been extended to validate the savings across all three library corners (typical, best and worst case specifications).
Abstract: Loop detectors report traffic characteristics in real
time. They are at the core of traffic control process. Intuitively,
one would expect that as density of detection increases, so would
the quality of estimates derived from detector data. However, as
detector deployment increases, the associated operating and
maintenance cost increases. Thus, traffic agencies often need to
decide where to add new detectors and which detectors should
continue receiving maintenance, given their resource constraints.
This paper evaluates the effect of detector spacing on freeway
travel time estimation. A freeway section (Interstate-15) in Salt
Lake City metropolitan region is examined. The research reveals
that travel time accuracy does not necessarily deteriorate with
increased detector spacing. Rather, the actual location of detectors
has far greater influence on the quality of travel time estimates.
The study presents an innovative computational approach that
delivers optimal detector locations through a process that relies on
Genetic Algorithm formulation.
Abstract: Emerging adulthood, the new period which is
especially prevalent in the developed or industrialized countries
during ages 18 to 29, is a new conceptualization proposed by Arnett.
Intimacy is a superordinate concept which includes intimate
interaction and intimate relationship. This study includes two
proceses which are scale development and conduction of gender
differences about markers of starting romantic intimacy among
Turkish emerging adults. In first process, Markers of Starting
Romantic Intimacy Scale, with 17 items and 5 factors, was developed
using by 220 participants. In the second step, the scale was
administered to 318 Turkish male and female emerging adults
between ages 22 and 25. Results show that there is no significant
difference between gender and total score of the scale. With respect
to gender, there are significant differences between gender and in
four subscales which are self perception, affective and cognitive
intimacy, self knowledge and romantic verbalizations. Moreover,
there is no significant relationship between gender and behavioral
intimacy subscale.
Abstract: Due to their high power-to-weight ratio and low cost,
pneumatic actuators are attractive for robotics and automation
applications; however, achieving fast and accurate control of their
position have been known as a complex control problem. A
methodology for obtaining high position accuracy with a linear
pneumatic actuator is presented. During experimentation with a
number of PID classical control approaches over many operations of
the pneumatic system, the need for frequent manual re-tuning of the
controller could not be eliminated. The reason for this problem is
thermal and energy losses inside the cylinder body due to the
complex friction forces developed by the piston displacements.
Although PD controllers performed very well over short periods, it
was necessary in our research project to introduce some form of
automatic gain-scheduling to achieve good long-term performance.
We chose a fuzzy logic system to do this, which proved to be an
easily designed and robust approach. Since the PD approach showed
very good behaviour in terms of position accuracy and settling time,
it was incorporated into a modified form of the 1st order Tagaki-
Sugeno fuzzy method to build an overall controller. This fuzzy gainscheduler
uses an input variable which automatically changes the PD
gain values of the controller according to the frequency of repeated
system operations. Performance of the new controller was
significantly improved and the need for manual re-tuning was
eliminated without a decrease in performance. The performance of
the controller operating with the above method is going to be tested
through a high-speed web network (GRID) for research purposes.