Abstract: This paper studies dynamic stability of homogeneous
beams with piezoelectric layers subjected to periodic axial
compressive load that is simply supported at both ends lies on a
continuous elastic foundation. The displacement field of beam is
assumed based on Bernoulli-Euler beam theory. Applying the
Hamilton's principle, the governing dynamic equation is established.
The influences of applied voltage, foundation coefficient and
piezoelectric thickness on the unstable regions are presented. To
investigate the accuracy of the present analysis, a compression study
is carried out with a known data.
Abstract: According to the masonry standard the compressive
strength is basically dependent on factors such as the mortar strength
and the relative values of unit and mortar strength. However
interlocking brick has none or less use of mortar. Therefore there is a need to investigate the behavior of masonry walls using interlocking
bricks. In this study a series of tests have been conducted; physical
properties and compressive strength of brick units and masonry walls
were constructed from interlocking bricks and tested under constant
vertical load at different eccentricities. The purpose of the
experimental investigations is to obtain the force displacement curves, analyze the behavior of masonry walls. The results showed
that the brick is categorized as common brick (BS 3921:1985) and severe weathering grade (ASTM C62). The maximum compressive stress of interlocking brick wall is 3.6 N/mm2 and fulfilled the requirement of standard for residential building.
Abstract: Background noise is particularly damaging to speech
intelligibility for people with hearing loss especially for sensorineural
loss patients. Several investigations on speech intelligibility have
demonstrated sensorineural loss patients need 5-15 dB higher SNR
than the normal hearing subjects. This paper describes Discrete
Cosine Transform Power Normalized Least Mean Square algorithm
to improve the SNR and to reduce the convergence rate of the LMS
for Sensory neural loss patients. Since it requires only real arithmetic,
it establishes the faster convergence rate as compare to time domain
LMS and also this transformation improves the eigenvalue
distribution of the input autocorrelation matrix of the LMS filter.
The DCT has good ortho-normal, separable, and energy compaction
property. Although the DCT does not separate frequencies, it is a
powerful signal decorrelator. It is a real valued function and thus
can be effectively used in real-time operation. The advantages of
DCT-LMS as compared to standard LMS algorithm are shown via
SNR and eigenvalue ratio computations. . Exploiting the symmetry
of the basis functions, the DCT transform matrix [AN] can be
factored into a series of ±1 butterflies and rotation angles. This
factorization results in one of the fastest DCT implementation. There
are different ways to obtain factorizations. This work uses the fast
factored DCT algorithm developed by Chen and company. The
computer simulations results show superior convergence
characteristics of the proposed algorithm by improving the SNR at
least 10 dB for input SNR less than and equal to 0 dB, faster
convergence speed and better time and frequency characteristics.
Abstract: The Programmable Logic Controller (PLC) plays a
vital role in automation and process control. Grafcet is used for
representing the control logic, and traditional programming
languages are used for describing the pure algorithms. Grafcet is used
for dividing the process to be automated in elementary sequences that
can be easily implemented. Each sequence represent a step that has
associated actions programmed using textual or graphical languages
after case. The programming task is simplified by using a set of
subroutines that are used in several steps. The paper presents an
example of implementation for a punching machine for sheets and
plates. The use the graphical languages the programming of a
complex sequential process is a necessary solution. The state of
Grafcet can be used for debugging and malfunction determination.
The use of the method combined with a set of knowledge acquisition
for process application reduces the downtime of the machine and
improve the productivity.
Abstract: This study has applied the L16 orthogonal array of the
Taguchi method to determine the optimized polymeric
Nanocomposite asphalt binder. Three control factors are defined as
polypropylene plastomer (PP), styrene-butadiene-styrene elastomer
(SBS) and Nanoclay. Four level of concentration contents are
introduced for prepared asphalt binder samples. all samples were
prepared with 4.5% of bitumen 60/70 content. Compressive strength
tests were carried out for defining the optimized sample via
QUALITEK-4 software. SBS with 3%, PP with 5 % and Nanoclay
with 1.5% of concentrations are defined as the optimized
Nanocomposite asphalt binders. The confirmation compressive
strength and also softening point tests showed that modification of
asphalt binders with this method, improved the compressive strength
and softening points of asphalt binders up to 55%.
Abstract: In this paper, we have developed an explicit analytical
drain current model comprising surface channel potential and
threshold voltage in order to explain the advantages of the proposed
Gate Stack Double Diffusion (GSDD) MOSFET design over the
conventional MOSFET with the same geometric specifications that
allow us to use the benefits of the incorporation of the high-k layer
between the oxide layer and gate metal aspect on the immunity of the
proposed design against the self-heating effects. In order to show the
efficiency of our proposed structure, we propose the simulation of the
power chopper circuit. The use of the proposed structure to design a
power chopper circuit has showed that the (GSDD) MOSFET can
improve the working of the circuit in terms of power dissipation and
self-heating effect immunity. The results so obtained are in close
proximity with the 2D simulated results thus confirming the validity
of the proposed model.
Abstract: Climate change is one of the greatest environmental,
economic, and social challenges of our time. Urban transportation has
had a major negative impact on our environment—most of our air
pollution comes from transport.
This paper explores ways to move toward a more sustainable
transport system by focusing on creating a more efficient and livable
city and improving the environmental efficiency of transport activity.
The analytical study covers some international examples of applying
sustainable transportation and uses them to suggest a frame work to
develop the transportation system in Egypt to be sustainable and more
intelligent.
Abstract: Alkali treated oil palm empty fruit bunch (EFB) fibres
(TEFBF) and untreated EFBF fibers (UEFBF) were incorporated in
polypropylene (PP) with and without malic anhydride grafted PP
(MAPP) and magnesium hydroxide as flame retardant (FR) to
produce TEFBF-PP and UEFBF-PP composites by the melt casting
method. The composites were characterized by mechanical and
burning tests along with a scanning electron microscope and Fourier
transform infrared spectroscopy. The significant improvement in
flexural modulus (133%) and flame retardant property (60%) of
TEFBF-PP composite with MAPP and FR is observed. The improved
mechanical property is discussed by the development of encapsulated
textures.
Abstract: Air bubbles have been detected in human circulation
of end-stage renal disease patients who are treated by hemodialysis.
The consequence of air embolism, air bubbles, is under recognized
and usually overlooked in daily practice. This paper shows results of
a capacitor based detection method that capable of detecting the
presence of air bubbles in the blood stream in different frequencies.
The method is based on a parallel plates capacitor made of platinum
with an area of 1.5 cm2 and a distance between the two plates is 1cm.
The dielectric material used in this capacitor is Dextran70 solution
which mimics blood rheology. Simulations were carried out using
RC circuit at two frequencies 30Hz and 3 kHz and results compared
with experiments and theory. It is observed that by injecting air
bubbles of different diameters into the device, there were significant
changes in the capacitance of the capacitor. Furthermore, it is
observed that the output voltage from the circuit increased with
increasing air bubble diameter. These results demonstrate the
feasibility of this approach in improving air bubble detection in
Hemodialysis.
Abstract: This paper presents the communication network for
machine vision system to implement to control systems and logistics
applications in industrial environment. The real-time distributed over
the network is very important for communication among vision node,
image processing and control as well as the distributed I/O node. A
robust implementation both with respect to camera packaging and
data transmission has been accounted. This network consists of a
gigabit Ethernet network and a switch with integrated fire-wall is
used to distribute the data and provide connection to the imaging
control station and IEC-61131 conform signal integration comprising
the Modbus TCP protocol. The real-time and delay time properties
each part on the network were considered and worked out in this
paper.
Abstract: The effect of SnO2 surface modification by Ag nanoclusters, synthesized by SILD method, on the operating characteristics of thin film gas sensors was studied and models for the promotional role of Ag additives were discussed. It was found that mentioned above approach can be used for improvement both the sensitivity and the rate of response of the SnO2-based gas sensors to CO and H2. At the same time, the presence of the Ag clusters on the surface of SnO2 depressed the sensor response to ozone.
Abstract: A method of dynamic mesh based airfoil optimization is proposed according to the drawbacks of surrogate model based airfoil optimization. Programs are designed to achieve the dynamic mesh. Boundary condition is add by integrating commercial software Pointwise, meanwhile the CFD calculation is carried out by commercial software Fluent. The data exchange and communication between the software and programs referred above have been accomplished, and the whole optimization process is performed in iSIGHT platform. A simplified airfoil optimization study case is brought out to show that aerodynamic performances of airfoil have been significantly improved, even save massive repeat operations and increase the robustness and credibility of the optimization result. The case above proclaims that dynamic mesh based airfoil optimization is an effective and high efficient method.
Abstract: Organic Flash Cycle (OFC) has potential of improving
efficiency for recovery of low temperature heat sources mainly due to
reducing temperature mismatch in the heat exchanger. In this work
exergetical performance analysis of ORC is conducted for recovery of
low grade heat source. Effects of system parameters such as flash
evaporation temperature or heating temperature are theoretically
investigated on the exergy destructions (anergies) at various
components of the system as well as exergy efficiency. Results show
that exergy efficiency has a peak with respect to the flash temperature,
and the optimum flash temperature increases with the heating
temperature. The component where the largest exergy destruction
occurs varies with the flash temperature or heating temperature.
Abstract: This paper presents the effect of corrugation profile
geometry on the crushing behavior, energy absorption, failure
mechanism, and failure mode of woven roving glass fibre/epoxy
laminated composite tube. Experimental investigations were carried
out on composite tubes with three different profile shapes: sinusoidal,
triangular and trapezoidal. The tubes were subjected to lateral
compressive loading. On the addition to a radial corrugated
composite tube, cylindrical composite tube, were fabricated and
tested under the same condition in order to know the effect of
corrugation geometry. Typical histories of their deformation are
presented. Behavior of tubes as regards the peak crushing load,
energy absorbed and mode of crushing has been discussed. The
results show that the behavior of the tube under lateral compression
load is influenced by the geometry of the tube itself.
Abstract: This study examines the relevance of disclosure
practices in improving the accountability and transparency of
religious nonprofit organizations (RNPOs). The assessment of
disclosure is based on the annual returns of RNPOs for the financial
year 2010. In order to quantify the information disclosed in the
annual returns, partial disclosure indexes of basic information (BI)
disclosure index, financial information (FI) disclosure index and
governance information (GI) disclosure index have been built which
takes into account the content of information items in the annual
returns. The empirical evidence obtained revealed low disclosure
practices among RNPOs in the sample. The multiple regression
results showed that the organizational attribute of the board size
appeared to be the most significant predictor for both partial index on
the extent of BI disclosure index, and FI disclosure index. On the
other hand, the extent of financial information disclosure is related to
the amount of donation received by RNPOs. On GI disclosure index,
the existence of an external audit appeared to be significant variable.
This study has contributed to the academic literature in providing
empirical evidence of the disclosure practices among RNPOs.
Abstract: Search for a tertiary substructure that geometrically
matches the 3D pattern of the binding site of a well-studied protein provides a solution to predict protein functions. In our previous work,
a web server has been built to predict protein-ligand binding sites
based on automatically extracted templates. However, a drawback of such templates is that the web server was prone to resulting in many
false positive matches. In this study, we present a sequence-order constraint to reduce the false positive matches of using automatically
extracted templates to predict protein-ligand binding sites. The binding site predictor comprises i) an automatically constructed template library and ii) a local structure alignment algorithm for
querying the library. The sequence-order constraint is employed to
identify the inconsistency between the local regions of the query protein and the templates. Experimental results reveal that the sequence-order constraint can largely reduce the false positive matches and is effective for template-based binding site prediction.
Abstract: Work Breakdown Structure (WBS) is one of the
most vital planning processes of the project management since it
is considered to be the fundamental of other processes like
scheduling, controlling, assigning responsibilities, etc. In fact
WBS or activity list is the heart of a project and omission of a
simple task can lead to an irrecoverable result. There are some
tools in order to generate a project WBS. One of the most
powerful tools is mind mapping which is the basis of this article.
Mind map is a method for thinking together and helps a project
manager to stimulate the mind of project team members to
generate project WBS. Here we try to generate a WBS of a
sample project involving with the building construction using the
aid of mind map and the artificial intelligence (AI) programming
language. Since mind map structure can not represent data in a
computerized way, we convert it to a semantic network which can
be used by the computer and then extract the final WBS from the
semantic network by the prolog programming language. This
method will result a comprehensive WBS and decrease the
probability of omitting project tasks.
Abstract: School leadership is commonly considered to have a
significant influence on school effectiveness and improvement.
Effective school leaders are expected to successfully introduce and
support change and innovation at the school unit. Despite an
abundance of studies on educational leadership, very few studies
have provided evidence on the link between leadership models, and
specific educational and school outcomes. This is true of a popular
contemporary approach to leadership, namely, distributed leadership.
The paper provides an overview of research findings on the effect of
distributed leadership on educational outcomes. The theoretical basis
for this approach to leadership is presented, with reference to
methodological and research limitations. The paper discusses
research findings and draws their implications for educational
research on school leadership.
Abstract: Pattern recognition is the research area of Artificial Intelligence that studies the operation and design of systems that recognize patterns in the data. Important application areas are image analysis, character recognition, fingerprint classification, speech analysis, DNA sequence identification, man and machine diagnostics, person identification and industrial inspection. The interest in improving the classification systems of data analysis is independent from the context of applications. In fact, in many studies it is often the case to have to recognize and to distinguish groups of various objects, which requires the need for valid instruments capable to perform this task. The objective of this article is to show several methodologies of Artificial Intelligence for data classification applied to biomedical patterns. In particular, this work deals with the realization of a Computer-Aided Detection system (CADe) that is able to assist the radiologist in identifying types of mammary tumor lesions. As an additional biomedical application of the classification systems, we present a study conducted on blood samples which shows how these methods may help to distinguish between carriers of Thalassemia (or Mediterranean Anaemia) and healthy subjects.
Abstract: The error diffusion method generates worm artifacts,
and weakens the edge of the halftone image when the continuous gray
scale image is reproduced by a binary image. First, to enhance the
edges, we propose the edge-enhancing filter by considering the
quantization error information and gradient of the neighboring pixels.
Furthermore, to remove worm artifacts often appearing in a halftone
image, we add adaptively random noise into the weights of an error
filter.