Abstract: Due to their high power-to-weight ratio and low cost, pneumatic actuators are attractive for robotics and automation applications; however, achieving fast and accurate control of their position have been known as a complex control problem. The paper presents a methodology for obtaining controllers that achieve high position accuracy and preserve the closed-loop characteristics over a broad operating range. Experimentation with a number of conventional (or "classical") three-term controllers shows that, as repeated operations accumulate, the characteristics of the pneumatic actuator change requiring frequent re-tuning of the controller parameters (PID gains). Furthermore, three-term controllers are found to perform poorly in recovering the closed-loop system after the application of load or other external disturbances. The key reason for these problems lies in the non-linear exchange of energy inside the cylinder relating, in particular, to the complex friction forces that develop on the piston-wall interface. In order to overcome this problem but still remain within the boundaries of classical control methods, we designed an auto selective classicaql controller so that the system performance would benefit from all three control gains (KP, Kd, Ki) according to system requirements and the characteristics of each type of controller. This challenging experimentation took place for consistent performance in the face of modelling imprecision and disturbances. In the work presented, a selective PID controller is presented for an experimental rig comprising an air cylinder driven by a variable-opening pneumatic valve and equipped with position and pressure sensors. The paper reports on tests carried out to investigate the capability of this specific controller to achieve consistent control performance under, repeated operations and other changes in operating conditions.
Abstract: Most of the collision warning systems currently
available in the automotive market are mainly designed to warn
against imminent rear-end and lane-changing collisions. No collision
warning system is commercially available to warn against imminent
turning collisions at intersections, especially for left-turn collisions
when a driver attempts to make a left-turn at either a signalized or
non-signalized intersection, conflicting with the path of other
approaching vehicles traveling on the opposite-direction traffic
stream. One of the major factors that lead to left-turn collisions is the
human error and misjudgment of the driver of the turning vehicle
when perceiving the speed and acceleration of other vehicles
traveling on the opposite-direction traffic stream; therefore, using a
properly-designed collision warning system will likely reduce, or
even eliminate, this type of collisions by reducing human error. This
paper introduces perceptual framework for a proposed collision
warning system that can detect imminent left-turn collisions at
intersections. The system utilizes a commercially-available detection
sensor (either a radar sensor or a laser detector) to detect approaching
vehicles traveling on the opposite-direction traffic stream and
calculate their speeds and acceleration rates to estimate the time-tocollision
and compare that time to the time required for the turning
vehicle to clear the intersection. When calculating the time required
for the turning vehicle to clear the intersection, consideration is given
to the perception-reaction time of the driver of the turning vehicle,
which is the time required by the driver to perceive the message
given by the warning system and react to it by engaging the throttle.
A regression model was developed to estimate perception-reaction
time based on age and gender of the driver of the host vehicle.
Desired acceleration rate selected by the driver of the turning vehicle,
when making the left-turn movement, is another human factor that is
considered by the system. Another regression model was developed
to estimate the acceleration rate selected by the driver of the turning
vehicle based on driver-s age and gender as well as on the location
and speed of the nearest approaching vehicle along with the
maximum acceleration rate provided by the mechanical
characteristics of the turning vehicle. By comparing time-to-collision
with the time required for the turning vehicle to clear the intersection,
the system displays a message to the driver of the turning vehicle
when departure is safe. An application example is provided to
illustrate the logic algorithm of the proposed system.
Abstract: The paper presents the service learning project titled
DicDucFac (idea-leadership-product), that was planned and
conducted by the team of information sciences students. It was
planned as a workshop dealing with the application of modern social
media (Facebook, YouTube, Gmail) for the purposes of selfpromotion,
free advertising via social networks and marketing own
ideas and/or products in the virtual world. The workshop was
organized for highly-skilled computer literate unemployed youth.
These youth, as final beneficiaries, will be able to apply what they
learned in this workshop to “the real world“, increasing their chances
for employment and self-employment. The results of the project
reveal that the basic, active-learning principles embodied in our
teaching approach allow students to learn more effectively and gain
essential life skills (from computer applications to teamwork) that
can only be learned by doing. It also shows that our students received
the essentials of professional ethics and citizenship through direct,
personal engagement in professional activities and the life of the
community.
Abstract: Larval rearing and seed production of most of tetra fishes (Family: Characidae) is critical due to their small size larvae and limited numbers of spawning attempts. During the present study the effect of different live foods on growth and survival of neon tetra, Paracheirodon innesi larvae (length 3.1 ± 0.012mm, weight 0.048 ± 0.00015mg) and early fry (length = 6.44 ± 0.025mm, weight = 0.64 ± 0.003mg and 13 days old) was determined in two experiments. Experiment I was conducted for rearing the larvae by using mixed green water and Infusoria whereas, in Experiment II, early fry were fed with mixed zooplankton, decapsulated Artemia cyst and Artemia nauplii. The larvae fed on mixed green water showed significant (p
Abstract: Thailand is one of the world-s leaders of rice
producers and exporters. Farmers have to increase the rice cultivation
frequency for serving the national increasing of export-s demand. It
leads to an elimination of rice residues by open burning which is the
quickest and costless management method. The open burning of rice
residue is one of the major causes of air pollutants and greenhouse
gas (GHG) emission. Under ASEAN agreement on trans-boundary
haze, Thailand set the master plan to mitigate air pollutant emission
from open burning of agricultural residues. In this master plan,
residues incorporation is promoted as alternative management
method to open burning. However, the assessment of both options in
term of GHG emission in order to investigate their contribution to
long-term global warming is still scarce or inexistent. In this study, a
method on rice residues assessment was first developed in order to
estimate and compare GHG emissions from rice cultivation under
rice residues open burning and the case with incorporation of the
same amount of rice residues, using 2006 IPCC guidelines for
emission estimation and Life Cycle Analysis technique. The
emission from rice cultivation in different preparing area practice
was also discussed.
Abstract: In this paper, perceptions of actors on changes in
crop productivity, quantity and quality of water, and determinants of
their perception are analyzed using descriptive statistics and ordered
logit model. Data collected from 297 Ethiopian farmers and 103
agricultural professionals from December 2009 to January 2010 are
employed. Results show that the majority of the farmers and
professionals recognized decline in water resources, reasoning
climate changes and soil erosion as some of the causes. However,
there is a variation in views on changes in productivity. The
household asset, education level, age and geographical positions are
found to affect farmers- perception on changes in crop productivity.
But, the study underlines that there is no evidence that farmers-
economic status, age, or education level affects recognition of
degradation of water resources. Thus, more focus shall be given on
providing them different coping mechanisms and alternative
resource conserving technologies than educating about the
problems.
Abstract: The current situation in the eurozone raises a number of topics for discussion and to help in finding an answer to the question of whether a common currency is a more suitable means of coping with the impact of the financial crisis or whether national currencies are better suited to this. The economic situation in the EU is now considerably volatile and, due to problems with the fulfilment of the Maastricht convergence criteria, it is now being considered whether, in their further development, new member states will decide to distance themselves from the euro or will, in an attempt to overcome the crisis, speed up the adoption of the euro. The Czech Republic is one country with little interest in adopting the euro, justified by the fact that a better alternative to dealing with this crisis is an independent monetary policy and its ability to respond flexibly to the economic situation not only in Europe, but around the world. One attribute of the crisis in the Czech Republic and its mitigation is the freely floating exchange rate of the national currency. It is not only the Czech Republic that is attempting to alleviate the impact of the crisis, but also new EU member countries facing fresh questions to which theory have yet to provide wholly satisfactory answers. These questions undoubtedly include the problem of inflation targeting and the choice of appropriate instruments for achieving financial stability. The difficulty lies in the fact that these objectives may be contradictory and may require more than one means of achieving them. In this respect we may assume that membership of the euro zone might not in itself mitigate the development of the recession or protect the nation from future crises. We are of the opinion that the decisive factor in the development of any economy will continue to be the domestic economic policy and the operability of market economic mechanisms. We attempt to document this fact using selected countries as examples, these being the Czech Republic, Poland, Hungary, and Slovakia.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: Many organisations are nowadays interested to adopt
lean manufacturing strategy that would enable them to compete in
this competitive globalisation market. In this respect, it is necessary
to assess the implementation of lean manufacturing in different
organisations so that the important best practices can be identified.
This paper describes the development of key areas which will be
used to assess the adoption and implementation of lean
manufacturing practices. There are some key areas developed to
evaluate and reduce the most optimal projects so as to enhance their
production efficiency and increase the purpose of the economic
benefits of the manufacturing unit.
Lean manufacturing is becoming lean enterprise by treating its
customers and suppliers as partners. This gives the extra edge in
today-s cost and time competitive markets. The organisation is
becoming strong in all the conventional competition points. They are
Price, Quality and Delivery. Lean enterprise owners can deliver high
quality products quickly, with low price.
Abstract: International literature emphasizes on the concern regarding the phenomenon of aggression in hospital. This paper focuses on the reality of aggressive interactions reigning within an emergency triage involving three chaps of protagonists: the professionals, the patients and their carers. The data collection was made from a grid of observation, in which the various variables exposed in the literature were integrated. They observations took place around the clock, for three weeks, at the rate of one week a month. In this research 331 aggressive interactions have been listed and analyzed by means of the software SPSS. This research is one of the very few continuous observation surveys in the literature. It shows the various human factors at play in the emergence of aggressive interaction. The data may be used both for taking steps in primary prevention, thanks to the analysis of interaction modes, and in secondary prevention by integrating the useful results in situational prevention.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: The field of biomedical materials plays an imperative
requisite and a critical role in manufacturing a variety of biological
artificial replacements in a modern world. Recently, titanium (Ti)
materials are being used as biomaterials because of their superior
corrosion resistance and tremendous specific strength, free- allergic
problems and the greatest biocompatibility compared to other
competing biomaterials such as stainless steel, Co-Cr alloys,
ceramics, polymers, and composite materials. However, regardless of
these excellent performance properties, Implantable Ti materials have
poor shear strength and wear resistance which limited their
applications as biomaterials. Even though the wear properties of Ti
alloys has revealed some improvements, the crucial effectiveness of
biomedical Ti alloys as wear components requires a comprehensive
deep understanding of the wear reasons, mechanisms, and techniques
that can be used to improve wear behavior. This review examines
current information on the effect of thermal and thermomechanical
processing of implantable Ti materials on the long-term prosthetic
requirement which related with wear behavior. This paper focuses
mainly on the evolution, evaluation and development of effective
microstructural features that can improve wear properties of bio
grade Ti materials using thermal and thermomechanical treatments.
Abstract: Recently, nanomaterials are developed in the form of nano-films, nano-crystals and nano-pores. Lanthanide phosphates as a material find extensive application as laser, ceramic, sensor, phosphor, and also in optoelectronics, medical and biological labels, solar cells and light sources. Among the different kinds of rare-earth orthophosphates, yttrium orthophosphate has been shown to be an efficient host lattice for rare earth activator ions, which have become a research focus because of their important role in the field of light display systems, lasers, and optoelectronic devices. It is in this context that the 4fn- « 4fn-1 5d transitions of rare earth in insulating materials, lying in the UV and VUV, are the aim of large number of studies .Though there has been a few reports on Eu3+, Nd3+, Pr3+,Er3+, Ce3+, Tm3+ doped YPO4. The 4fn- « 4fn-1 5d transitions of the rare earth dependent to the host-matrix, several matrices ions were used to study these transitions, in this work we are suggesting to study on a very specific class of inorganic material that are orthophosphate doped with rare earth ions. This study focused on the effect of Ce3+ concentration on the structural and optical properties of Ce3+ doped YPO4 yttrium orthophosphate with powder form prepared by the Sol Gel method.
Abstract: Accurately predicting non-peak traffic is crucial to
daily traffic for all forecasting models. In the paper, least squares
support vector machines (LS-SVMs) are investigated to solve such a
practical problem. It is the first time to apply the approach and analyze
the forecast performance in the domain. For comparison purpose, two
parametric and two non-parametric techniques are selected because of
their effectiveness proved in past research. Having good
generalization ability and guaranteeing global minima, LS-SVMs
perform better than the others. Providing sufficient improvement in
stability and robustness reveals that the approach is practically
promising.
Abstract: In this paper we present a new method for over-height
vehicle detection in low headroom streets and highways using digital
video possessing. The accuracy and the lower price comparing to
present detectors like laser radars and the capability of providing
extra information like speed and height measurement make this
method more reliable and efficient. In this algorithm the features are
selected and tracked using KLT algorithm. A blob extraction
algorithm is also applied using background estimation and
subtraction. Then the world coordinates of features that are inside the
blobs are estimated using a noble calibration method. As, the heights
of the features are calculated, we apply a threshold to select overheight
features and eliminate others. The over-height features are
segmented using some association criteria and grouped using an
undirected graph. Then they are tracked through sequential frames.
The obtained groups refer to over-height vehicles in a scene.
Abstract: The ever-growing usage of aspect-oriented
development methodology in the field of software engineering
requires tool support for both research environments and industry. So
far, tool support for many activities in aspect-oriented software
development has been proposed, to automate and facilitate their
development. For instance, the AJaTS provides a transformation
system to support aspect-oriented development and refactoring. In
particular, it is well established that the abstract interpretation of
programs, in any paradigm, pursued in static analysis is best served
by a high-level programs representation, such as Control Flow Graph
(CFG). This is why such analysis can more easily locate common
programmatic idioms for which helpful transformation are already
known as well as, association between the input program and
intermediate representation can be more closely maintained.
However, although the current researches define the good concepts
and foundations, to some extent, for control flow analysis of aspectoriented
programs but they do not provide a concrete tool that can
solely construct the CFG of these programs. Furthermore, most of
these works focus on addressing the other issues regarding Aspect-
Oriented Software Development (AOSD) such as testing or data flow
analysis rather than CFG itself. Therefore, this study is dedicated to
build an aspect-oriented control flow graph construction tool called
AJcFgraph Builder. The given tool can be applied in many software
engineering tasks in the context of AOSD such as, software testing,
software metrics, and so forth.
Abstract: Ant Colony Algorithms have been applied to difficult
combinatorial optimization problems such as the travelling salesman
problem and the quadratic assignment problem. In this paper gridbased
and random-based ant colony algorithms are proposed for
automatic 3D hose routing and their pros and cons are discussed. The
algorithm uses the tessellated format for the obstacles and the
generated hoses in order to detect collisions. The representation of
obstacles and hoses in the tessellated format greatly helps the
algorithm towards handling free-form objects and speeds up
computation. The performance of algorithm has been tested on a
number of 3D models.
Abstract: Drinking water is one of the most valuable resources
available to mankind. The presence of pathogens in drinking water is
highly undesirable. Because of the Lateritic soil, the iron
concentrations were high in ground water. High concentration of iron
and other trace elements could restrict bacterial growth and modify
their metabolic pattern as well. The bacterial growth rate reduced in
the presence of iron in water. This paper presents the results of a
controlled laboratory study conducted to assess the inhibition of
micro-organism (pathogen) in well waters in the presence of
dissolved iron concentrations. Synthetic samples were studied in the
laboratory and the results compared with field samples. Predictive
model for microbial inhibition in the presence of iron is presented. It
was seen that the bore wells, open wells and the field results varied,
probably due to the nature of micro-organism utilizing the iron in
well waters.