Abstract: In the present study, the rate of NOx emission in a
combustion chamber working in conventional combustion and High
Temperature Air Combustion (HiTAC) system are examined using
CFD modeling. The effect of peak temperature, combustion air
temperature and oxygen concentration on NOx emission rate was
undertaken. Results show that in a fixed oxygen concentration,
increasing the preheated air temperature will increase the peak
temperature and NOx emission rate. In addition, it was observed that
the reduction of the oxygen concentration in the fixed preheated air
temperature decreases the peak temperature and NOx emission rate.
On the other hand, the results show that increase of preheated air
temperature at various oxygen concentrations increases the NOx
emission rate. However, the rate of increase in HiTAC conditions is
quite lower than the conventional combustion. The modeling results
show that the NOx emission rate in HiTAC combustion is 133% less
than that of the conventional combustion.
Abstract: Lattice Monte Carlo methods are an excellent
choice for the simulation of non-linear thermal diffusion
problems. In this paper, and for the first time, Lattice Monte
Carlo analysis is performed on thermal diffusion combined
with convective heat transfer. Laminar flow of water modeled
as an incompressible fluid inside a copper pipe with a constant
surface temperature is considered. For the simulation of
thermal conduction, the temperature dependence of the
thermal conductivity of the water is accounted for. Using the
novel Lattice Monte Carlo approach, temperature distributions
and energy fluxes are obtained.
Abstract: The paper presents a new hybridization methodology involving Neural, Fuzzy and Rough Computing. A Rough Sets based approximation technique has been proposed based on a certain Neuro – Fuzzy architecture. A New Rough Neuron composition consisting of a combination of a Lower Bound neuron and a Boundary neuron has also been described. The conventional convergence of error in back propagation has been given away for a new framework based on 'Output Excitation Factor' and an inverse input transfer function. The paper also presents a brief comparison of performances, of the existing Rough Neural Networks and ANFIS architecture against the proposed methodology. It can be observed that the rough approximation based neuro-fuzzy architecture is superior to its counterparts.
Abstract: The adverse effects of Clindamycin (Clind.) /
Ibuprofen (Ibu.) combination on liver, kidney, blood elements and the
significances of antioxidants (N-acetylcysteine and Zinc) against
these effects were evaluated. The study includes: Group I; control
n=30, Group II; patients on Clind.300mg/Ibu.400mg twice daily for a
week n=30, Group III; patients on Clind.300mg/Ibu.400mg+Nacetylcysteine
200mg twice daily for a week n=15 and Group IV;
patients on Clind.300mg/Ibu.400mg+Zinc50mg twice daily for a
week n=15. Serum malondialdehyde (MDA), alanine transferase
(ALT), aspartate transferase (AST), γ glutamyl transferase (GGT),
creatinine, blood urea nitrogen (BUN) were measured. Applying one
way ANOVA followed by Tuckey Kramer post test, Group II showed
significant increase in ALT, AST, GGT, BUN and decrease in Hb,
RBCs, platelets than Group I. Group III showed significant decrease
in ALT, AST, GGT, BUN than Group II. Moreover, Group IV
showed significant decrease in ALT, AST, GGT and increase in Hb,
RBCs, and platelets than Group II. Conclusively, Adding Zinc or Nacetylcysteine
buffer the oxidative stress and improve the therapeutic
outcome of Clindamycin/Ibuprofen combination.
Abstract: The interaction between wakes of bluff body and
airfoil have profound influences on system performance in many
industrial applications, e.g., turbo-machinery and cooling fan. The
present work investigates the effect of configuration include; airfoil-s
angle of attack, transverse and inline spacing of the models, on
frequency behavior of the cylinder-s near-wake. The experiments
carried on under subcritical flow regime, using the hot-wire
anemometry (HWA). The relationship between the Strouhal numbers
and arrangements provide an insight into the global physical
processes of wake interaction and vortex shedding.
Abstract: Non-stationary trend in R-R interval series is
considered as a main factor that could highly influence the evaluation
of spectral analysis. It is suggested to remove trends in order to obtain
reliable results. In this study, three detrending methods, the
smoothness prior approach, the wavelet and the empirical mode
decomposition, were compared on artificial R-R interval series with
four types of simulated trends. The Lomb-Scargle periodogram was
used for spectral analysis of R-R interval series. Results indicated that
the wavelet method showed a better overall performance than the other
two methods, and more time-saving, too. Therefore it was selected for
spectral analysis of real R-R interval series of thirty-seven healthy
subjects. Significant decreases (19.94±5.87% in the low frequency
band and 18.97±5.78% in the ratio (p
Abstract: Genetically modified (GM) technology in food
production continued to generate controversies. Consumers were
concerned with the GM foods about the healthy and environmental
risks. While consumers- acceptance was a critical factor affecting how
widely this technology be used. According to the research review,
consumers- lack of information was one of the reasons to explain
consumers- low acceptance toward GM foods. The objective for this
study wanted to find out would informative product package affect
consumers- behavior toward GM foods. An experiment was designed
to investigate consumer behavior toward different product package
information. The results indicated that the product package
information influenced consumer product trust toward GM foods.
Compared with the traceability production system information, the
information about the GM rice was approved by authorized
organizations could increase consumers product trust in GM foods.
Consumers in Taiwan saw the information provided by authorized
organizations more credible than other information.
Abstract: This paper developed the c-Chart based on a Zero- Inflated Poisson (ZIP) processes that approximated by a geometric distribution with parameter p. The p estimated that fit for ZIP distribution used in calculated the mean, median, and variance of geometric distribution for constructed the c-Chart by three difference methods. For cg-Chart, developed c-Chart by used the mean and variance of the geometric distribution constructed control limits. For cmg-Chart, the mean used for constructed the control limits. The cme- Chart, developed control limits of c-Chart from median and variance values of geometric distribution. The performance of charts considered from the Average Run Length and Average Coverage Probability. We found that for an in-control process, the cg-Chart is superior for low level of mean at all level of proportion zero. For an out-of-control process, the cmg-Chart and cme-Chart are the best for mean = 2, 3 and 4 at all level of parameter.
Abstract: Learning is the acquisition of new mental schemata, knowledge, abilities and skills which can be used to solve problems potentially more successfully. The learning process is optimum when it is assisted and personalized. Learning is not a single activity, but should involve many possible activities to make learning become meaningful. Many e-learning applications provide facilities to support teaching and learning activities. One way to identify whether the e-learning system is being used by the learners is through the number of hits that can be obtained from the e-learning system's log data. However, we cannot rely solely to the number of hits in order to determine whether learning had occurred meaningfully. This is due to the fact that meaningful learning should engage five characteristics namely active, constructive, intentional, authentic and cooperative. This paper aims to analyze the e-learning activities that is meaningful to learning. By focusing on the meaningful learning characteristics, we match it to the corresponding Moodle e-learning activities. This analysis discovers the activities that have high impact to meaningful learning, as well as activities that are less meaningful. The high impact activities is given high weights since it become important to meaningful learning, while the low impact has less weight and said to be supportive e-learning activities. The result of this analysis helps us categorize which e-learning activities that are meaningful to learning and guide us to measure the effectiveness of e-learning usage.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: Soy polyol obtained from hydroxylation of soy
epoxide with ethylene glycol were prepared as pre-polyurethane. The
two step process method were applied in the polyurethane synthesis.
The blending of soy polyol with synthetic polyol then simultaneously
carried out to TDI (2,4): MDI (4,4-) (80:20), blowing agent, and
surfactant. Ethylene glycol were not taking part in the polyurethane
synthesis. The inclusion of ethylene glycol were used as a control.
Characterization of polyurethane foam through impact resillience,
indentation deflection, and density can visualize the polyurethane
classifications.
Abstract: Bladder carcinoma is an important worldwide health problem. Both cystoscopy and urine cytology used in detecting bladder cancer suffer from drawbacks where cystoscopy is an invasive method and urine cytology shows low sensitivity in low grade tumors. This study validates easier and less time-consuming techniques to evaluate the value of combined use of angiogenin and clusterin in comparison and combination with voided urine cytology in the detection of bladder cancer patients. This study includes malignant (bladder cancer patients, n= 50), benign (n=20) and healthy (n=20) groups. The studied groups were subjected to cystoscopic examination, detection of bilharzial antibodies, urine cytology, and estimation of urinary angiogenin and clusterin by ELISA. The overall sensitivity and specificity were 66% and 75% for angiogenin, 70% and 82.5% for clusterin and 46% and 80% for voided urine cytology. Combined sensitivity of angiogenin and clusterin with urine cytology increased from 82 to 88%.
Abstract: The tracking allows to detect the tumor affections of cervical cancer, it is particularly complex and consuming time, because it consists in seeking some abnormal cells among a cluster of normal cells. In this paper, we present our proposed computer system for helping the doctors in tracking the cervical cancer. Knowing that the diagnosis of the malignancy is based in the set of atypical morphological details of all cells, herein, we present an unsupervised genetic algorithm for the separation of cell components since the diagnosis is doing by analysis of the core and the cytoplasm. We give also the various algorithms used for computing the morphological characteristics of cells (Ratio core/cytoplasm, cellular deformity, ...) necessary for the recognition of illness.
Abstract: The objective of the study is to investigate the
effect of a footballer-s postural on selected physical fitness
components. Twenty-one (21) subjects of the university male
footballers under the Sport Excellence Center programme were
photographed using qualitative analysis. The postural variables
were stratified manually into normal and anomalies group and
their flexibility, strength and SAQ performance were
compared using the Mann-Whitney Test. The AROM
assessment and SAQ test reported no significance difference
(Z=-.398, p=0.711, p>0.05), similar to the lower body strength
was shown with no significance different (Z=-.493, p=0.640,
p>0.05). In contrast, only 1 RM strength test for the upper
body strength test shown with a significance different (Z=-
2.537, p=0.009, p
Abstract: In this paper, a set of experimental data has been used to assess the influence of abrasive water jet (AWJ) process parameters in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. The effects of these input parameters are studied on depth of cut (h); one of most important characteristics of AWJ. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. In the next stage, the proposed model is embedded into a Simulated Annealing (SA) algorithm to optimize the AWJ process parameters. The objective is to determine a suitable set of process parameters that can produce a desired depth of cut, considering the ranges of the process parameters. Computational results prove the effectiveness of the proposed model and optimization procedure.
Abstract: Plant growth is affected by the osmotic stress as well as toxicity of salt in leaves. In order to study of salt stress effects on stomatal conductance and growth rate and relationship between them as wells osmotic and Na+-specific effects on these traits, four bread wheat genotypes differing in salt tolerance were selected. Salinity was applied when the leaf 4 was fully expanded. Sodium (Na+) concentrations in flag leaf blade at 3 salinity levels (0, 100 and 200 mM NaCl) were measured. Salt-tolerant genotypes showed higher stomatal conductance and growth rate compared to salt-sensitive ones. After 10 and 20 days exposure to salt, stomatal conductance and relative growth rate were reduced, but the reduction was greater in sensitive genotypes. Growth rate was reduced severely in the first period (1-10 days) of salt commencements and it was due to osmotic effect of salt not Na+ toxicity. In the second period (11-20 days) after salt treatment growth reduced only when salt accumulated to toxic concentrations in the leaves. A positive relationship between stomatal conductance and relative growth rate showed that stomatal conductance can be a reliable indicator of growth rate, and finally can be considered as a sensitive indicator of the osmotic stress. It seems 20 days after salinity, the major effect of salt, especially at low to moderate salinity levels on growth properties was due to the osmotic effect of salt, not to Na+-specific effects within the plant.
Abstract: This paper studied the synthesis of monoacylglycerol (monolaurin) by glycerolysis of coconut oil and crude glycerol, catalyzed by Carica papaya lipase. Coconut oil obtained from cold pressed extraction method and crude glycerol obtained from the biodiesel plant in Department of Chemistry, Uttaradit Rajabhat University, Thailand which used oils were used as raw materials for biodiesel production through transesterification process catalyzed by sodium hydroxide. The influences of the following variables were studied: (i) type of organic solvent, (ii) molar ratio of substrate, (iii) reaction temperature, (iv) reaction time, (v) lipase dosage, and (vi) initial water activity of enzyme. High yields in monoacylglycerol (58.35%) were obtained with molar ratio of glycerol to oil at 8:1 in ethanol, temperature was controlled at 45oC for 36 hours, the amount of enzyme used was 20 wt% of oil and initial water activity of enzyme at 0.53.
Abstract: Aircraft propulsion systems often use Y-shaped
subsonic diffusing ducts as twin air-intakes to supply the ambient air
into the engine compressor for thrust generation. Due to space
constraint, the diffusers need to be curved, which causes severe flow
non-uniformity at the engine face. The present study attempt to
control flow in a mild-curved Y-duct diffuser using trapezoidalshaped
vortex generators (VG) attached on either both the sidewalls
or top and bottom walls of the diffuser at the inflexion plane. A
commercial computational fluid dynamics (CFD) code is modified
and is used to simulate the effects of SVG in flow of a Y-duct
diffuser. A few experiments are conducted for CFD code validation,
while the rest are done computationally. The best combination of Yduct
diffuser is found with VG-2 arranged in co-rotating sequence
and attached to both the sidewalls, which ensures highest static
pressure recovery, lowest total pressure loss, minimum flow
distortion and less flow separation in Y-duct diffuser. The decrease in
VG height while attached to top and bottom walls further improves
axial flow uniformity at the diffuser outlet by a great margin as
compared to the bare duct.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: In this research, natural canthaxanthin as one of the
most important carotenoids was extracted from Dietzia
natronolimnaea HS-1. The changes of canthaxanthin enriched in oilin-
water emulsions with vegetable oil (5 mg/ 100 mL), Arabic gum (5
mg/100 mL), and potassium sorbate (0.5 g/100 mL) was investigated.
The effects of different pH (3, 5 and 7), as well as, time treatment (3,
18 and 33 days) in the environmental temperature (24°C) on the
degradation were studied by response surface methodology (RSM).
The Hunter values (L*, a*, and b*) and the concentration of
canthaxanthin (C, mg/L) illustrated more degradation of this pigment
at low pHs (pH≤ 4) by passing the time (days≥10) with R² 97.00%,
91.31%, 97.60%, and 99.54% for C, L*, a*, and b* respectively. The
predicted model were found to be significant (p