Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.
Abstract: Negative pressure phenomenon appears in many
thermodynamic, geophysical and biophysical processes in the Nature
and technological systems. For more than 100 years of the laboratory
researches beginning from F. M. Donny’s tests, the great values of
negative pressure have been achieved. But this phenomenon has not
been practically applied, being only a nice lab toy due to the special
demands for the purity and homogeneity of the liquids for its
appearance. The possibility of creation of direct wave of negative
pressure in real heterogeneous liquid systems was confirmed
experimentally under the certain kinetic and hydraulic conditions.
The negative pressure can be considered as the factor of both useful
and destroying energies. The new approach to generation of the
negative pressure waves in impure, unclean fluids has allowed the
creation of principally new energy saving technologies and
installations to increase the effectiveness and efficiency of different
production processes. It was proved that the negative pressure is one
of the main factors causing hard troubles in some technological and
natural processes. Received results emphasize the necessity to take
into account the role of the negative pressure as an energy factor in
evaluation of many transient thermohydrodynamic processes in the
Nature and production systems.
Abstract: Leukaemia is a blood cancer disease that contributes
to the increment of mortality rate in Malaysia each year. There are
two main categories for leukaemia, which are acute and chronic
leukaemia. The production and development of acute leukaemia cells
occurs rapidly and uncontrollable. Therefore, if the identification of
acute leukaemia cells could be done fast and effectively, proper
treatment and medicine could be delivered. Due to the requirement of
prompt and accurate diagnosis of leukaemia, the current study has
proposed unsupervised pixel segmentation based on clustering
algorithm in order to obtain a fully segmented abnormal white blood
cell (blast) in acute leukaemia image. In order to obtain the
segmented blast, the current study proposed three clustering
algorithms which are k-means, fuzzy c-means and moving k-means
algorithms have been applied on the saturation component image.
Then, median filter and seeded region growing area extraction
algorithms have been applied, to smooth the region of segmented
blast and to remove the large unwanted regions from the image,
respectively. Comparisons among the three clustering algorithms are
made in order to measure the performance of each clustering
algorithm on segmenting the blast area. Based on the good sensitivity
value that has been obtained, the results indicate that moving kmeans
clustering algorithm has successfully produced the fully
segmented blast region in acute leukaemia image. Hence, indicating
that the resultant images could be helpful to haematologists for
further analysis of acute leukaemia.
Abstract: Motion Tracking and Stereo Vision are complicated,
albeit well-understood problems in computer vision. Existing
softwares that combine the two approaches to perform stereo motion
tracking typically employ complicated and computationally expensive
procedures. The purpose of this study is to create a simple and
effective solution capable of combining the two approaches. The
study aims to explore a strategy to combine the two techniques
of two-dimensional motion tracking using Kalman Filter; and depth
detection of object using Stereo Vision. In conventional approaches
objects in the scene of interest are observed using a single camera.
However for Stereo Motion Tracking; the scene of interest is
observed using video feeds from two calibrated cameras. Using two
simultaneous measurements from the two cameras a calculation for
the depth of the object from the plane containing the cameras is made.
The approach attempts to capture the entire three-dimensional spatial
information of each object at the scene and represent it through a
software estimator object. In discrete intervals, the estimator tracks
object motion in the plane parallel to plane containing cameras and
updates the perpendicular distance value of the object from the plane
containing the cameras as depth. The ability to efficiently track
the motion of objects in three-dimensional space using a simplified
approach could prove to be an indispensable tool in a variety of
surveillance scenarios. The approach may find application from high
security surveillance scenes such as premises of bank vaults, prisons
or other detention facilities; to low cost applications in supermarkets
and car parking lots.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index
Abstract: The problem of psychologist training remains a key
priority in Armenia. During the Soviet period, the notion of a
psychologist was obscure not only in Armenia but also in other
Soviet republics. The breakup of the Soviet Union triggered a gradual
change in this area activating the cooperation with specialists from
other countries. The need for recovery from the psychological trauma
caused by the 1988 earthquake pushed forward the development of
practical psychology in Armenia. This phenomenon led to positive
changes in perception of and interest to a psychologist
profession.Armenian universities started designing special programs
for psychologists’ preparation. Armenian psychologists combined
their efforts in the field of training relevant specialists.
During the recent years, the Bologna educational system was
introduced in Armenia which led to implementation of education
quality improvement programs. Nevertheless, even today the issue of
psychologists’ training is not yet settled in Armenian universities. So
far graduate psychologists haven’t got a clear idea of personal and
professional qualities of a psychologist. Recently, as a result of
educational reforms, the psychology curricula underwent changes,
but so far they have not led to a desired outcome. Almost all curricula
in certain specialties are aimed to form professional competencies
and strengthen practical skills.
A survey conducted in Armenia aimed to identify what are the
ideas of young psychology specialists on the image of a psychologist.
The survey respondents were 45 specialists holding bachelor’s degree
as well as 30 master degree graduates, who have not been working
yet. The research reveals that we need to change the approach of
preparing psychology practitioners in the universities of Armenia.
Such an approach to psychologist training will make it possible to
train qualified specialists for enhancement of modern psychology
theory and practice.
Abstract: Compositions of different molar ratios of
polymethylmethacrylate-co-methacrylic acid (PMMA-co-MAA)
were synthesized via free-radical polymerization. Polymer coated
surfaces have been produced on silicon wafers. Coated samples were
analyzed by atomic force microscopy (AFM). The results have shown
that the roughness of the surfaces have increased by increasing the
molar ratio of monomer methacrylic acid (MAA). This study reveals
that the gradual increase in surface roughness is due to the fact that
carboxylic functional groups have been generated by MAA segments.
Such surfaces can be desirable platforms for fabrication of the
biosensors for detection of the viruses and diseases.
Abstract: The research was conducted to empirically validate
the proposed maturity model of e-Government implementation,
composed of four dimensions, further specified by 54 success factors
as attributes. To do so, there are two steps were performed. First,
expert’s judgment was conducted to test its content validity. The
second, reliability study was performed to evaluate inter-rater
agreement by using Fleiss Kappa approach. The kappa statistic
(kappa coefficient) is the most commonly used method for testing the
consistency among raters. Fleiss Kappa was a generalization of
Kappa in extensions to the case of more than two raters (multiple
raters) with multi-categorical ratings. Our findings show that most
attributes of the proposed model were related to their corresponding
dimensions. According to our results, The percentage of agree
answers given by the experts was 73.69% in dimension A, 89.76% in
B, 81.5% in C and 60.37% in D. This means that more than half of
the attributes of each dimensions were appropriate or relevant to the
dimensions they were supposed to measure, while 85% of attributes
were relevant enough to their corresponding dimensions. Inter-rater
reliability coefficient also showed satisfactory result and interpreted
as substantial agreement among raters. Therefore, the proposed
model in this paper was valid and reliable to measure the maturity of
e-Government implementation.
Abstract: Burnishing is increasingly used as a finishing operation to improve surface roughness and surface hardness. This can be achieved by applying a hard ball or roller onto metallic surfaces under pressure, in order to achieve many advantages in the metallic surface. In the present work, the feed rate, speed and force have been considered as the basic burnishing parameters to study the surface roughness and surface hardness of metallic matrix composites. The considered metal matrix composites were made from Aluminum-Magnesium-Graphite with five different weight percentage of graphite. Both effects of burnishing parameters mentioned above and the graphite percentage on the surface hardness and surface roughness of the metallic matrix composites were studied. The results of this investigation showed that the surface hardness of the metallic composites increases with the increase of the burnishing force and decreases with the increase in the burnishing feed rate and burnishing speed. The surface roughness of the metallic composites decreases with the increasing of the burnishing force, feed rate, and speed to certain values, then it starts to increase. On the other hand, the increase in the weight percentage of the graphite in the considered composites causes a decrease in the surface hardness and an increase in the surface roughness.
Abstract: Reverse Logistics (RL) Network is considered as
complex and dynamic network that involves many stakeholders such
as: suppliers, manufactures, warehouse, retails and costumers, this
complexity is inherent in such process due to lack of perfect
knowledge or conflicting information. Ontologies on the other hand
can be considered as an approach to overcome the problem of sharing
knowledge and communication among the various reverse logistics
partners. In this paper we propose a semantic representation based on
hybrid architecture for building the Ontologies in ascendant way, this
method facilitates the semantic reconciliation between the
heterogeneous information systems that support reverse logistics
processes and product data.
Abstract: The aim of this work was to apply extractive
distillation for acetonitrile removal from water solutions, to validate
thermodynamic criterion based on excess Gibbs energy to entrainer
selection process for acetonitrile – water mixture separation and show
its potential efficiency at isothermal conditions as well as at isobaric
(conditions of real distillation process), to simulate and analyze an
extractive distillation process with chosen entrainers: optimize
amount of trays and feeds, entrainer/original mixture and reflux
ratios. Equimolar composition of the feed stream was chosen for the
process, comparison of the energy consumptions was carried out.
Glycerol was suggested as the most energetically and ecologically
suitable entrainer.
Abstract: Pipe failure and leakage is a problematic issue and the
traditional solution of replacing the pipes is costly and time
consuming. Rehabilitation by relining materials based on polymer
composites is an alternative solution towards the degradation problem
of the old piping. This paper provides a brief summary of advances in
technology, methods and materials for relining as well as a summary
of the degradation analyses of the two main composite materials used
for relining, rubber filled epoxy and reinforced polyester baltoflake
when they are exposed in deionized water and elevated temperature
up to 80°C for a duration of 2-14 months in the laboratory.
Abstract: Early pre-code reinforced concrete structures present
undetermined resistance to earthquakes. This situation is particularly
unacceptable in the case of essential structures, such as healthcare
structures and pilgrims' houses. Amongst these, an existing old RC
building in Madinah city (KSA) is seismically evaluated with and
without infill wall and their dynamic characteristics are compared
with measured values in the field using ambient vibration
measurements (AVM). After updating the mathematical models for
this building with the experimental results, three dimensional
pushover analysis (Nonlinear static analysis) was carried out using
commercial structural analysis software incorporating inelastic
material properties for concrete, infill and steel. The purpose of this
analysis is to evaluate the expected performance of structural systems
by estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results summarized and discussed.
Abstract: The idea of the asynchronous transmission in
wavelength division multiplexing (WDM) ring MANs is studied in
this paper. Especially, we present an efficient access technique to
coordinate the collisions-free transmission of the variable sizes of IP
traffic in WDM ring core networks. Each node is equipped with a
tunable transmitter and a tunable receiver. In this way, all the
wavelengths are exploited for both transmission and reception. In
order to evaluate the performance measures of average throughput,
queuing delay and packet dropping probability at the buffers, a
simulation model that assumes symmetric access rights among the
nodes is developed based on Poisson statistics. Extensive numerical
results show that the proposed protocol achieves apart from high
bandwidth exploitation for a wide range of offered load, fairness of
queuing delay and dropping events among the different packets size
categories.
Abstract: Food is widely packaged with plastic materials to
prevent microbial contamination and spoilage. Ionizing radiation is
widely used to sterilize the food-packaging materials. Sterilization by
γ-radiation causes degradation such as embrittlement, stiffening,
softening, discoloration, odour generation, and decrease in molecular
weight. Many antioxidants can prevent γ-degradation but most of
them are toxic. The migration of antioxidants to its environment
gives rise to major concerns in case of food packaging plastics. In
this attempt, we have aimed to utilize synergistic mixtures of
stabilizers which are approved for food-contact applications.
Ethylene-propylene-diene terpolymer has been melt-mixed with
hindered amine stabilizers (HAS), phenolic antioxidants and organophosphites
(hydroperoxide decomposer). Results were discussed by
comparing the stabilizing efficiency of mixtures with and without
phenol system. Among phenol containing systems where we mostly
observed discoloration due to the oxidation of hindered phenol, the
combination of secondary HAS, tertiary HAS, organo-phosphite and
hindered phenol exhibited improved stabilization efficiency than
single or binary additive systems. The mixture of secondary HAS and
tertiary HAS, has shown antagonistic effect of stabilization.
However, the combination of organo-phosphite with secondary HAS,
tertiary HAS and phenol antioxidants have been found to give
synergistic even at higher doses of Gamma-irradiation. The effects
have been explained through the interaction between the stabilizers.
After γ-irradiation, the consumption of oligomeric stabilizer
significantly depends on the components of stabilization mixture. The
effect of the organo-phosphite antioxidant on the overall stability has
been discussed.
Abstract: The rate of natural gas dissociation from the Coal
Matrix depends on depressurization of reservoir through removing of
the cleat water from the coal seam. These waters are similar to brine
and aged of very long years. For improving the connectivity through
fracking /fracturing, high pressure liquids are pumped off inside the
coal body. A significant quantity of accumulated water, a combined
mixture of cleat water and fracking fluids (back flow water) is
pumped out through gas well. In Queensland, Australia Coal Seam
Gas (CSG) industry is in booming state and estimated of 30,000 wells
would be active for CSG production forecasting life span of 30 years.
Integrated water management along with water softening programs is
practiced for subsequent treatment and later on discharge to nearby
surface water catchment. Water treatment is an important part of the
CSG industry. A case study on a CSG site and review on the test
results are discussed for assessing the Standards & Practices for
management of CSG by-product water and their subsequent disposal
activities. This study was directed toward (i) water management and
softening process in Spring Gully CSG field, (ii) Comparative
analysis on experimental study and standards and (iii) Disposal of the
treated water. This study also aimed for alternative usages and their
impact on vegetation, living species as well as long term effects.
Abstract: A mixed method by combining modified pole
clustering technique and modified cauer continued fraction is
proposed for reducing the order of the large-scale dynamic systems.
The denominator polynomial of the reduced order model is obtained
by using modified pole clustering technique while the coefficients of
the numerator are obtained by modified cauer continued fraction.
This method generated 'k' number of reduced order models for kth
order reduction. The superiority of the proposed method has been
elaborated through numerical example taken from the literature and
compared with few existing order reduction methods.
Abstract: Composite materials, due to their unique properties
such as high strength to weight ratio, corrosion resistance, and impact
resistance have huge potential as structural materials in automotive,
construction and transportation applications. However, these
properties often come at higher cost owing to complex design
methods, difficult manufacturing processes and raw material cost.
Traditionally, tapered laminated composite structures are
manufactured using autoclave manufacturing process by ply drop off
technique. Autoclave manufacturing though very powerful suffers
from high capital investment and higher energy consumption. As per
the current trends in composite manufacturing, Out of Autoclave
(OoA) processes are looked as emerging technologies for
manufacturing the structural composite components for aerospace
and defense applications. However, there is a need for improvement
among these processes to make them reliable and consistent. In this
paper, feasibility of using out of autoclave process to manufacture the
variable thickness cantilever beam is discussed. The minimum weight
design for the composite beam is obtained using constant stress beam
concept by tailoring the thickness of the beam. Ply drop off
techniques was used to fabricate the variable thickness beam from
glass/epoxy prepregs. Experiments were conducted to measure
bending stresses along the span of the cantilever beam at different
intervals by applying the concentrated load at the free end.
Experimental results showed that the stresses in the bean at different
intervals were constant. This proves the ability of OoA process to
manufacture the constant stress beam. Finite element model for the
constant stress beam was developed using commercial finite element
simulation software. It was observed that the simulation results
agreed very well with the experimental results and thus validated
design and manufacturing approach used.