Abstract: The antioxidant compounds are needed for the food, beverages, and pharmaceuticals industry. For this purpose, an appropriate method is required to measure the antioxidant properties in various types of samples. Spectrophotometric method usually used has some weaknesses, including the high price, long sample preparation time, and less sensitivity. Among the alternative methods developed to overcome these weaknesses is antioxidant biosensor based on superoxide dismutase (SOD) enzyme. Therefore, this study was carried out to measure the SOD activity originating from Deinococcus radiodurans and to determine its kinetics properties. Carbon paste electrode modified with ferrocene and immobilized SOD exhibited anode and cathode current peak at potential of +400 and +300mv respectively, in both pure SOD and SOD of D. radiodurans. This indicated that the current generated was from superoxide catalytic dismutation reaction by SOD. Optimum conditions for SOD activity was at pH 9 and temperature of 27.50C for D. radiodurans SOD, and pH 11 and temperature of 200C for pure SOD. Dismutation reaction kinetics of superoxide catalyzed by SOD followed the Lineweaver-Burk kinetics with D. radiodurans SOD KMapp value was smaller than pure SOD. The result showed that D. radiodurans SOD had higher enzyme-substrate affinity and specificity than pure SOD. It concluded that D. radiodurans SOD had a great potential as biological recognition component for antioxidant biosensor.
Abstract: Global temperature had increased by about 0.5oC over
the past century, increasing temperature leads to a loss or a decrease
of soil organic matter (SOM). Whereas soil organic matter in many
tropical soils is less stable than that of temperate soils, and it will be
easily affected by climate change. Therefore, conservation of soil
organic matter is urgent issue nowadays. This paper presents the
effect of different doses (5%, 15%) of Ca-type zeolite in conjunction
with organic manure, applied to soil samples from Philippines,
Paraguay and Japan, on the decomposition resistance of soil organic
matter under high temperature. Results showed that a remain or
slightly increase the C/N ratio of soil. There are an increase in
percent of humic acid (PQ) that extracted with Na4P2O7. A decrease
of percent of free humus (fH) after incubation was determined. A
larger the relative color intensity (RF) value and a lower the color
coefficient (6logK) value following increasing zeolite rates leading
to a higher degrees of humification. The increase in the aromatic
condensation of humic acid (HA) after incubation, as indicates by the
decrease of H/C and O/C ratios of HA. This finding indicates that the
use of zeolite could be beneficial with respect to SOM conservation
under global warming condition.
Abstract: Beginning from the creator of integro-differential
equations Volterra, many scientists have investigated these
equations. Classic method for solving integro-differential
equations is the quadratures method that is successfully applied up
today. Unlike these methods, Makroglou applied hybrid methods
that are modified and generalized in this paper and applied to the
numerical solution of Volterra integro-differential equations. The
way for defining the coefficients of the suggested method is also
given.
Abstract: Due to dynamic evolution, the ability of a
manufacturing technology to produce a special product is changing.
Therefore, it is essential to monitor the established techniques and
processes to detect whether a company-s production will fit future
circumstances. Concerning the manufacturing technology planning
process, companies must decide when to change to a new technology
for maintaining and increasing competitive advantages. In this
context, the maturity assessment of the focused technologies is
crucial. This article presents an approach for defining the maturity of
a manufacturing technology from a strategic point of view. The
concept is based on the approach of technology readiness level
(TRL) according to NASA (National Aeronautics and Space
Administration), but also includes dynamic changes. Therefore, the
model takes into account the concept of the technology life cycle.
Furthermore, it enables a company to estimate the ideal date for
implementation of a new manufacturing technology.
Abstract: Intelligent systems are required in order to quickly and accurately analyze enormous quantities of data in the Internet environment. In intelligent systems, information extracting processes can be divided into supervised learning and unsupervised learning. This paper investigates intelligent clustering by unsupervised learning. Intelligent clustering is the clustering system which determines the clustering model for data analysis and evaluates results by itself. This system can make a clustering model more rapidly, objectively and accurately than an analyzer. The methodology for the automatic clustering intelligent system is a multi-agent system that comprises a clustering agent and a cluster performance evaluation agent. An agent exchanges information about clusters with another agent and the system determines the optimal cluster number through this information. Experiments using data sets in the UCI Machine Repository are performed in order to prove the validity of the system.
Abstract: In Data mining, Fuzzy clustering algorithms have
demonstrated advantage over crisp clustering algorithms in dealing
with the challenges posed by large collections of vague and uncertain
natural data. This paper reviews concept of fuzzy logic and fuzzy
clustering. The classical fuzzy c-means algorithm is presented and its
limitations are highlighted. Based on the study of the fuzzy c-means
algorithm and its extensions, we propose a modification to the cmeans
algorithm to overcome the limitations of it in calculating the
new cluster centers and in finding the membership values with
natural data. The efficiency of the new modified method is
demonstrated on real data collected for Bhutan-s Gross National
Happiness (GNH) program.
Abstract: Boron minerals are very useful for various industrial
activities, such as glass industry and detergent industry, due to its
mechanical and chemical properties. During the production of boron
compounds, many of these are introduced into the environment in the
form of waste. Boron is also an important micro nutrient for the
plants to vegetate but if it exists in high concentrations, it could have
toxic effects. The maximum boron level in drinking water for human
health is given as 0.3 mg/L in World Health Organization (WHO)
standards. The toxic effects of boron should be noted especially for
dry regions, thus, in recent years, increasing attention has been paid
to remove the boron from waste waters. In this study, boron removal
is implemented by ion exchange process using Amberlite IRA-743
resin. Amberlite IRA-743 resin is a boron specific resin and it
belongs to the polymerizate sorbent group within the aminopolyol
functional group. Batch studies were performed to investigate the
effects of various experimental parameters, such as adsorbent dose,
initial concentration and pH, on the removal of boron. It is found
that, when the adsorbent dose increases removal of boron from the
liquid phase increases. However, an increase in the initial
concentration decreases the removal of boron. The effective pH
values for removal of boron are determined between 8.5 and 9.
Equilibrium isotherms were also analyzed by Langmuir and
Freundlich isotherm models. The Langmuir isotherm is obeyed better
than the Freundlich isotherm.
Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.
Abstract: A modified Genetic Algorithm (GA) based optimal selection of parameters for Automatic Generation Control (AGC) of multi-area electric energy systems is proposed in this paper. Simulations on multi-area reheat thermal system with and without consideration of nonlinearity like governor dead band followed by 1% step load perturbation is performed to exemplify the optimum parameter search. In this proposed method, a modified Genetic Algorithm is proposed where one point crossover with modification is employed. Positional dependency in respect of crossing site helps to maintain diversity of search point as well as exploitation of already known optimum value. This makes a trade-off between exploration and exploitation of search space to find global optimum in less number of generations. The proposed GA along with decomposition technique as developed has been used to obtain the optimum megawatt frequency control of multi-area electric energy systems. Time-domain simulations are conducted with trapezoidal integration along with decomposition technique. The superiority of the proposed method over existing one is verified from simulations and comparisons.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: Due to the low heavy metal concentrations, the
bottom ash from a 32 MW municipal district heating plant was
determined to be a potential forest fertilizer as such. However,
additional Ca would be needed, because its Ca concentration of 1.9-
% (d.w.) was lower than the statutory Finnish minimum limit value
of 6.0-% (d.w.) for Ca in forest fertilizer. Due to the elevated As
concentration (53.0 mg/kg; d.w.) in the fly ash from the 32 MW
municipal district heating plant, and Cr concentration (620 mg/kg;
d.w.) in the ash fraction (i.e. mixture of the bottom ash and fly ash)
from the 6 MW municipal district heating plant, which exceed the
limit values of 30 mg/kg (d.w.) and 300 mg/kg (d.w.) for As and Cr,
respectively, these residues are not suitable as forest fertilizers.
Although these ash fractions cannot be used as a forest fertilizer as
such, they can be used for the landscaping of landfills or in industrial
and other areas that are closed to the public. However, an
environmental permit is then needed.
Abstract: Partial coherence between two signals removing the contribution of a periodic, deterministic signal is proposed for evaluating the interrelationship in multivariate systems. The estimator expression was derived and shown to be independent of such periodic signal. Simulations were used for obtaining its critical value, which were found to be the same as those for Gaussian signals, as well as for evaluating the technique. An Illustration with eletroencephalografic (EEG) signals during photic stimulation is also provided. The application of the proposed technique in both simulation and real EEG data indicate that it seems to be very specific in removing the contribution of periodic sources. The estimate independence of the periodic signal may widen partial coherence application to signal analysis, since it could be used together with simple coherence to test for contamination in signals by a common, periodic noise source.
Abstract: This paper describes the design and modeling
procedure of a novel 5-phase segment type switched reluctance motor
(ST-SRM) under simultaneous two-phase (bipolar) excitation of
windings. The rotor cores of ST-SRM are embedded in an aluminum
block as well as to improve the performance characteristics. The
magnetic circuit of the produced ST-SRM is constructed so that the
magnetic flux paths are short and exclusive to each phase, thereby
minimizing the commutation switching and eddy current losses in the
laminations. The design and simulation principles presented apply
primarily to conventional SRM and ST-SRM. It is proved that the
novel 5-phase switched reluctance motor under two-phase excitation
is superior among the criteria used in comparison. The purposed
model is particularly well suited for high torque and weight
constrained applications such as automobiles, aerospace and military
applications.
Abstract: The main purpose of this research aimed to create tactile texture designed media for the blind used for extra learning outside classrooms in order to enhance imagination of the blind about Himmapan creatures, furthermore, the main objective of the research focused on improving the visual disabled perception to be equal to normal people. The target group of the research is blinded students studying in The Bangkok school for the blind between grade 4-6 in the second semester of 2011 who are able to read the braille language. The research methodology consisted of the field study and the documentary study related to the blind, tactile texture designed media and Himmapan creatures. 10 pictures of tactile texture designed media were created in the designing process which began after the analysis had conducted based the primary and secondary data. The works had presented to experts in the visual disabled field who evaluated the works. After approval, the works used as prototype to teach the blind. KeywordsBlind, Himmapan Creatures, Tactile Texture.
Abstract: This paper emphasizes on the application of genetic algorithm (GA) to optimize the parameters of the TMD for achieving the best results in the reduction of the building response under earthquake excitations. The Integral of the Time multiplied Absolute value of the Error (ITAE) based on relative displacement of all floors in the building is taken as a performance index of the optimization criterion. The problem of robustly TMD controller design is formatted as an optimization problem based on the ITAE performance index to be solved using GA that has a story ability to find the most optimistic results. An 11–story realistic building, located in the city of Rasht, Iran is considered as a test system to demonstrate effectiveness of the proposed GA based TMD (GATMD) controller without specifying which mode should be controlled. The results of the proposed GATMD controller are compared with the uncontrolled structure through timedomain simulation and some performance indices. The results analysis reveals that the designed GA based TMD controller has an excellent capability in reduction of the seismically excited example building and the ITAE performance, that is so for remains as unknown, can be introduced a new criteria - method for structural dynamic design.
Abstract: Modes of occurrence of Pb, As, Cr, Co, Cu, and Ni in bituminous coal and lignite were determined by means of sequential extraction using NH4OAc, HCl, HF and HNO3 extraction solutions. Elemental affinities obtained were then evaluated in relation to volatility of these elements during the combustion of these coals in two circulating fluidised-bed power stations. It was found out that higher percentage of the elements bound in silicates brought about lower volatility, while higher elemental proportion with monosulphides association (or bound as exchangeable ion) resulted in higher volatility. The only exception was the behavior of arsenic, whose volatility depended on amount of limestone added during the combustion process (as desulphurisation additive) rather than to its association in coal.
Abstract: This study used Item Analysis, Exploratory Factor
Analysis (EFA) and Reliability Analysis (Cronbach-s α value) to
exam the Questions which selected by the Delphi method based on the
issue of “Socio-technical system (STS)" and user-centered
perspective. A structure questionnaire with seventy-four questions
which could be categorized into nine dimensions (healthcare
environment, organization behaviour, system quality, medical data
quality, service quality, safety quality, user usage, user satisfaction,
and organization net benefits) was provided to evaluate EMR of the
Taiwanese healthcare environment.
Abstract: Effective estimation of just noticeable distortion (JND) for images is helpful to increase the efficiency of a compression algorithm in which both the statistical redundancy and the perceptual redundancy should be accurately removed. In this paper, we design a DCT-based model for estimating JND profiles of color images. Based on a mathematical model of measuring the base detection threshold for each DCT coefficient in the color component of color images, the luminance masking adjustment, the contrast masking adjustment, and the cross masking adjustment are utilized for luminance component, and the variance-based masking adjustment based on the coefficient variation in the block is proposed for chrominance components. In order to verify the proposed model, the JND estimator is incorporated into the conventional JPEG coder to improve the compression performance. A subjective and fair viewing test is designed to evaluate the visual quality of the coding image under the specified viewing condition. The simulation results show that the JPEG coder integrated with the proposed DCT-based JND model gives better coding bit rates at visually lossless quality for a variety of color images.
Abstract: Exponentially weighted moving average control chart (EWMA) is a popular chart used for detecting shift in the mean of parameter of distributions in quality control. The objective of this paper is to compare the efficiency of control chart to detect an increases in the mean of a process. In particular, we compared the Maximum Exponentially Weighted Moving Average (MaxEWMA) and Maximum Generally Weighted Moving Average (MaxGWMA) control charts when the observations are Exponential distribution. The criteria for evaluate the performance of control chart is called, the Average Run Length (ARL). The result of comparison show that in the case of process is small sample size, the MaxEWMA control chart is more efficiency to detect shift in the process mean than MaxGWMA control chart. For the case of large sample size, the MaxEWMA control chart is more sensitive to detect small shift in the process mean than MaxGWMA control chart, and when the process is a large shift in mean, the MaxGWMA control chart is more sensitive to detect mean shift than MaxEWMA control chart.
Abstract: This paper investigates how the use of machine learning techniques can significantly predict the three major dimensions of learner-s emotions (pleasure, arousal and dominance) from brainwaves. This study has adopted an experimentation in which participants were exposed to a set of pictures from the International Affective Picture System (IAPS) while their electrical brain activity was recorded with an electroencephalogram (EEG). The pictures were already rated in a previous study via the affective rating system Self-Assessment Manikin (SAM) to assess the three dimensions of pleasure, arousal, and dominance. For each picture, we took the mean of these values for all subjects used in this previous study and associated them to the recorded brainwaves of the participants in our study. Correlation and regression analyses confirmed the hypothesis that brainwave measures could significantly predict emotional dimensions. This can be very useful in the case of impassive, taciturn or disabled learners. Standard classification techniques were used to assess the reliability of the automatic detection of learners- three major dimensions from the brainwaves. We discuss the results and the pertinence of such a method to assess learner-s emotions and integrate it into a brainwavesensing Intelligent Tutoring System.