Abstract: This article presents the main results of a numerical
investigation on the uncertainty of dynamic response of structures
with statistically correlated random damping Gamma distributed. A
computational method based on a Linear Statistical Model (LSM) is
implemented to predict second order statistics for the response of a
typical industrial building structure. The significance of random
damping with correlated parameters and its implications on the
sensitivity of structural peak response in the neighborhood of a
resonant frequency are discussed in light of considerable ranges of
damping uncertainties and correlation coefficients. The results are
compared to those generated using Monte Carlo simulation
techniques. The numerical results obtained show the importance of
damping uncertainty and statistical correlation of damping
coefficients when obtaining accurate probabilistic estimates of
dynamic response of structures. Furthermore, the effectiveness of the
LSM model to efficiently predict uncertainty propagation for
structural dynamic problems with correlated damping parameters is
demonstrated.
Abstract: The present study focused on the investigation of the
effects of roughness elements on heat transfer during natural
convection in a rectangular cavity using numerical technique.
Roughness elements were introduced on the bottom hot wall with a
normalized amplitude (A*/H) of 0.1. Thermal and hydrodynamic
behaviors were studied using computational method based on Lattice
Boltzmann method (LBM). Numerical studies were performed for a
laminar flow in the range of Rayleigh number (Ra) from 103 to 106
for a rectangular cavity of aspect ratio (L/H) 2.0 with a fluid of
Prandtl number (Pr) 1.0. The presence of the sinusoidal roughness
elements caused a minimum to maximum decrease in the heat
transfer as 7% to 17% respectively compared to smooth enclosure.
The results are presented for mean Nusselt number (Nu), isotherms
and streamlines.
Abstract: The study conducted a simulation of the effect of sea
water to the bonding capacity of GFRP sheet on the concrete beams
using a simulation tank. Fiber reinforced polymer (FRP) has been
developed and applied in many fields civil engineering structures on
the new structures and also for strengthening of the deteriorated
structures. The FRP has advantages such as its corrosion resistance as
well as high tensile strength to weight ratio. Compared to the other
FRP materials, Glass composed FRP (GFRP) is relatively cheaper.
GFRP sheet is applied externally by bonding it on the concrete surface.
The studies regarding the application of GFRP sheet have been
conducted such as strengthening system, bonding behavior of GFRP
sheet including the application as reinforcement in new structures. For
application to the structures with direct contact to sea environment, a
study regarding the effect of sea water to the bonding capacity of
GFRP sheet is important to be clarified. To achieve the objective of the
study, a series of concrete beams strengthened with GFRP sheet on
extreme tension surface were prepared. The beams then were stored on
the sea water tank for six months. Results indicated the bonding
capacity decreased after six month exposed to the sea water.
Abstract: The Green Urban Lab took the form of public
installations that were placed at various locations in four cities in
Cyprus. These installations - through which a series of events,
activities, workshops and research took place - were the main tools in
regenerating a series of urban public spaces in Cyprus. The purpose
of this project was to identify issues and opportunities related to
public space and to offer guidelines on how design and participatory
democracy improvements could strengthen civil society, while
raising the quality of the urban public scene. Giant inflatable
structures were injected in important urban fragments in order to
accommodate series of events. The design and playful installation
generated a wide community engagement. The fluid presence of the
installations acted as a catalyst for social interaction. They were
accessed and viewed effortlessly and surprisingly, creating
opportunities to rediscover public spaces.
Abstract: The aim of this study was to determine the factor
structure and psychometric properties (i.e., reliability and convergent
validity) of the Employee Trust Scale, a newly created instrument by
the researchers. The Employee Trust Scale initially contained 82
items to measure employees’ trust toward their supervisors. A sample
of 818 (343 females, 449 males) employees were selected randomly
from public and private organization sectors in Kota Kinabalu,
Sabah, Malaysia. Their ages ranged from 19 to 67 years old with a
mean of 34.55 years old. Their average tenure with their current
employer was 11.2 years (s.d. = 7.5 years). The respondents were
asked to complete the Employee Trust Scale, as well as a managerial
trust questionnaire from Mishra. The exploratory factor analysis on
employees’ trust toward their supervisor’s extracted three factors,
labeled ‘trustworthiness’ (32 items), ‘position status’ (11 items) and
‘relationship’ (6 items) which accounted for 62.49% of the total
variance. Trustworthiness factors were re-categorized into three sub
factors: competency (11 items), benevolence (8 items) and integrity
(13 items). All factors and sub factors of the scales demonstrated
clear reliability with internal consistency of Cronbach’s Alpha above
.85. The convergent validity of the Scale was supported by an
expected pattern of correlations (positive and significant correlation)
between the score of all factors and sub factors of the scale and the
score on the managerial trust questionnaire, which measured the same
construct. The convergent validity of Employee Trust Scale was
further supported by the significant and positive inter-correlation
between the factors and sub factors of the scale. The results suggest
that the Employee Trust Scale is a reliable and valid measure.
However, further studies need to be carried out in other groups of
sample as to further validate the Scale.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: Rapid prototyping is a new group of manufacturing
processes, which allows fabrication of physical of any complexity
using a layer by layer deposition technique directly from a computer
system. The rapid prototyping process greatly reduces the time and
cost necessary to bring a new product to market. The prototypes
made by these systems are used in a range of industrial application
including design evaluation, verification, testing, and as patterns for
casting processes. These processes employ a variety of materials and
mechanisms to build up the layers to build the part. The present work
was to build a FDM prototyping machine that could control the X-Y
motion and material deposition, to generate two-dimensional and
three-dimensional complex shapes. This study focused on the
deposition of wax material. This work was to find out the properties
of the wax materials used in this work in order to enable better
control of the FDM process. This study will look at the integration of
a computer controlled electro-mechanical system with the traditional
FDM additive prototyping process. The characteristics of the wax
were also analysed in order to optimise the model production process.
These included wax phase change temperature, wax viscosity and
wax droplet shape during processing.
Abstract: In recent years, the power system has been changed
and a flexible power pricing system such as demand response has been
sought in Japan. The demand response system works simply in the
household sector and the owner as the decision-maker, can benefit
from power saving. On the other hand, the execution of demand
response in the office building is more complex than in the household
because various people such as owners, building administrators and
occupants are involved in the decision-making process. While the
owners benefit from demand saving, the occupants are exposed to
restricted benefits of a demand-saved environment. One of the reasons
is that building systems are usually under centralized management and
each occupant cannot choose freely whether to participate in demand
response or not. In addition, it is unclear whether incentives give
occupants the motivation to participate. However, the recent
development of IT and building systems enables the personalized
control of the office environment where each occupant can control the
lighting level or temperature individually. Therefore, it can be possible
to have a system which each occupant can make a decision of whether
or not to participate in demand response in the office building. This study investigates personal responses to demand response
requests, under the condition where each occupant can adjust their
brightness individually in their workspace. Once workers participate
in the demand response, their desk-lights are automatically turned off.
The participation rates in the demand response events are compared
among four groups, which are divided by different motivation, the
presence, or absence of incentives and the method of participation. The
result shows that there are significant differences of participation rates
in demand response event between four groups. The method of
participation has a large effect on the participation rate. The “Opt-out”
groups where the occupants are automatically enrolled in a demand
response event if they do not express non-participation have the
highest participation rate in the four groups. Incentives also have an
effect on the participation rate. This study also reports on the impact of low illumination office
environment on the occupants, such as stress or fatigue. The
electrocardiogram and the questionnaire are used to investigate the
autonomic nervous activity and subjective fatigue symptoms of the
occupants. There is no big difference between dim workspace during
demand response event and bright workspace in autonomic nervous
activity and fatigue.
Abstract: The activation volume of 6082T6 aluminum is
investigated at different temperatures for grain size variants. The
deformation activation volume was computed on the basis of the
relationship between the Boltzmann’s constant k, the testing
temperatures, the material strain rate sensitivity and the material yield
stress grain size variants. The material strain rate sensitivity is
computed as a function of yield stress and strain rate grain size
variants. The effect of the material strain rate sensitivity and the
deformation activation volume of 6082T6 aluminum at different
temperatures of 3-D grain are discussed. It is shown that the strain rate sensitivities and activation volume
are negative for the grain size variants during the deformation of
nanostructured materials. It is also observed that the activation
volume vary in different ways with the equivalent radius, semi minor
axis radius, semi major axis radius and major axis radius. From the
obtained results it is shown that the variation of activation volume
increase and decrease with the testing temperature. It was revealed
that, increase in strain rate sensitivity led to decrease in activation
volume whereas increase in activation volume led to decrease in
strain rate sensitivity.
Abstract: Myocardial infarction is one of the leading causes of
death in the world. Some of these deaths occur even before the
patient reaches the hospital. Myocardial infarction occurs as a result
of impaired blood supply. Because the most of these deaths are due to
coronary artery disease, hence the awareness of the warning signs of
a heart attack is essential. Some heart attacks are sudden and intense,
but most of them start slowly, with mild pain or discomfort, then
early detection and successful treatment of these symptoms is vital to
save them. Therefore, importance and usefulness of a system
designing to assist physicians in early diagnosis of the acute heart
attacks is obvious. The main purpose of this study would be to enable patients to
become better informed about their condition and to encourage them
to seek professional care at an earlier stage in the appropriate
situations. For this purpose, the data were collected on 711 heart
patients in Iran hospitals. 28 attributes of clinical factors can be
reported by patients; were studied. Three logistic regression models
were made on the basis of the 28 features to predict the risk of heart
attacks. The best logistic regression model in terms of performance
had a C-index of 0.955 and with an accuracy of 94.9%. The variables,
severe chest pain, back pain, cold sweats, shortness of breath, nausea
and vomiting, were selected as the main features.
Abstract: Public participation in recycling domestic waste is still
very low in Malaysia. Only 10.5% of solid waste was recycled up to
now which is far below than of in developed countries. Therefore,
understanding public motivations towards recycling domestic waste
are important to improve current recycling rate. Thus, this study
attempts to identify what are the possible motivations and hindrances
for the public to recycle. Open-ended questions format were
administered to 484 people in Kota Kinabalu, Sabah, Malaysia. Two
specific questions we asked to explore their general determinants and
barriers in practicing recycling: “What motivates you to recycle?”
and “What are the barriers you encountered in doing recycling
activities?” Thematic was conducted on the open-ended questions in
which themes were created with the raw comments. It was found that
the underlying recycling motivations are (i) awareness’ towards the
environment; (ii) benefits to the society and individual; and (iii)
social influence. Non participations are influence by (i) attitudes; (ii)
commitment; (iii) facilities; (iv) knowledge; (v) inconvenience; and
(vi) enforcement.
Abstract: On account of the concern of the fossil fuel is
depleting and its negative effects on the environment, interest in
alternative energy sources is increasing day by day. However,
considering the importance of transportation in human life, instead of
oil and its derivatives fueled vehicles with internal combustion
engines, electric vehicles which are sensitive to the environment and
working with electrical energy has begun to develop. In this study,
simulation was carried out for providing energy management and
recovering regenerative braking in fuel cell-battery hybrid electric
vehicle. The main power supply of the vehicle is fuel cell on the other
hand not only instantaneous power is supplied by the battery but also
the energy generated due to regenerative breaking is stored in the
battery. Obtained results of the simulation is analyzed and discussed.
Abstract: Dead wood and habitat tree such as fallen logs, snags,
stumps and cracks and loos bark etc. are regarded as an important
ecological component of forests on which many forest dwelling
species depend on presence of them within forest ecosystems.
Meanwhile its relation to management history in Caspian forest has
gone unreported. The aim of research was to compare the amounts of
dead wood and habitat trees in the forests with historically different
intensities of management, including: forests with the long term
implication of management (PS), the short term implication of
management (NS) which were compared with semi virgin forest
(GS). The number of 405 individual dead and habitat trees were
recorded and measured at 109 sampling locations. ANOVA revealed
volume of dead tree in the form and decay classes significantly differ
within sites and dead volume in the semi virgin forest significantly
higher than managed sites. Comparing the amount of dead and
habitat tree in three sites showed that, dead tree volume related with
management history and significantly differ in three study sites.
Meanwhile, frequency of habitat trees was significantly different
within sites. The highest amount of habitat trees including cavities,
cracks and loose bark and fork split trees was recorded in virgin site
and lowest recorded in the sites with the long term implication of
management. It can be concluded that forest management cause
reduction of the amount of dead and habitat tree specially in a large
size, thus managing this forest according to ecological sustainable
principles require a commitment to maintaining stand structure that
allow, continued generation of dead trees in a full range of size.
Abstract: In this paper, a asymptotically periodic predator-prey
model with Modified Leslie-Gower and Holling-Type II schemes
is investigated. Some sufficient conditions for the uniformly strong
persistence of the system are established. Our result is an important
complementarity to the earlier results.
Abstract: A mixed method for model order reduction is
presented in this paper. The denominator polynomial is derived by
matching both Markov parameters and time moments, whereas
numerator polynomial derivation and error minimization is done
using Genetic Algorithm. The efficiency of the proposed method can
be investigated in terms of closeness of the response of reduced order
model with respect to that of higher order original model and a
comparison of the integral square error as well.
Abstract: One of the tasks of optical surveillance is to detect
anomalies in large amounts of image data. However, if the size of the
anomaly is very small, limited information is available to distinguish
it from the surrounding environment. Spectral detection provides a
useful source of additional information and may help to detect
anomalies with a size of a few pixels or less. Unfortunately, spectral
cameras are expensive because of the difficulty of separating two
spatial in addition to one spectral dimension. We investigate the
possibility of modifying a simple spectral line detector for outdoor
detection. This may be especially useful if the area of interest forms a
line, such as the horizon. We use a monochrome CCD that also
enables detection into the near infrared. A simple camera is attached
to the setup to determine which part of the environment is spectrally
imaged. Our preliminary results indicate that sensitive detection of
very small targets is indeed possible. Spectra could be taken from the
various targets by averaging columns in the line image. By imaging a
set of lines of various widths we found narrow lines that could not be
seen in the color image but remained visible in the spectral line
image. A simultaneous analysis of the entire spectra can produce
better results than visual inspection of the line spectral image. We are
presently developing calibration targets for spatial and spectral
focusing and alignment with the spatial camera. This will present
improved results and more use in outdoor application.
Abstract: The reheating furnace is used to reheat the steel slabs
before the hot-rolling process. The supported system includes the
stationary/moving beams, and the skid buttons which block some
thermal radiation transmitted to the bottom of the slabs. Therefore, it is
important to analyze the steel slab temperature distribution during the
heating period. A three-dimensional mathematical transient heat
transfer model for the prediction of temperature distribution within the
slab has been developed. The effects of different skid button height
(H=60mm, 90mm, and 120mm) and different gap distance between
two slabs (S=50mm, 75mm, and 100mm) on the slab skid mark
formation and temperature profiles are investigated. Comparison with
the in-situ experimental data from Steel Company in Taiwan shows
that the present heat transfer model works well for the prediction of
thermal behavior of the slab in the reheating furnace. It is found that
the skid mark severity decreases with an increase in the skid button
height. The effect of gap distance is important only for the slab edge
planes, while it is insignificant for the slab central planes.
Abstract: The aim of the performed work is to establish the 2D
and 3D model of direct unsteady task of sample heat treatment by
moving source employing computer model on the basis of finite
element method. Complex boundary condition on heat loaded sample
surface is the essential feature of the task. Computer model describes
heat treatment of the sample during heat source movement over the
sample surface. It is started from 2D task of sample cross section as a
basic model. Possibilities of extension from 2D to 3D task are
discussed. The effect of the addition of third model dimension on
temperature distribution in the sample is showed. Comparison of
various model parameters on the sample temperatures is observed.
Influence of heat source motion on the depth of material heat
treatment is shown for several velocities of the movement. Presented
computer model is prepared for the utilization in laser treatment of
machine parts.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear
dynamics analysis of the structures with assuming elastic-perfectlyplastic
behavior was performed using RAM PERFORM-3D software;
the horizontal component was taken into consideration with and
without the incorporation of the corresponding vertical component.
Dynamic responses obtained for the horizontal component acting
alone were compared with those obtained from the simultaneous
application of both seismic components. The results show that the
effect of the vertical component of ground motion may increase the
axial load significantly in the interior columns and, consequently, the
stories. The plastic mechanisms would be changed. The P-Delta
effect is expected to increase. The punching base plate shear of the
columns should be considered. Moreover, the vertical component
increases the input energy when the structures exhibit inelastic
behavior and are taller.
Abstract: Automated Teller Machines (ATMs) can be
considered among one of the most important service facilities in the
banking industry. The investment in ATMs and the impact on the
banking industry is growing steadily in every part of the world. The
banks take into consideration many factors like safety, convenience,
visibility, and cost in order to determine the optimum locations of
ATMs. Today, ATMs are not only available in bank branches but
also at retail locations. Another important factor is the cash
management in ATMs. A cash demand model for every ATM is
needed in order to have an efficient cash management system. This
forecasting model is based on historical cash demand data which is
highly related to the ATMs location. So, the location and the cash
management problem should be considered together. This paper
provides a general review on studies, efforts and development in
ATMs location and cash management problem.