Abstract: Qatar’s primary source of fresh water is through
seawater desalination. Amongst the major processes that are
commercially available on the market, the most common large scale
techniques are Multi-Stage Flash distillation (MSF), Multi Effect
distillation (MED), and Reverse Osmosis (RO). Although commonly
used, these three processes are highly expensive down to high energy
input requirements and high operating costs allied with maintenance
and stress induced on the systems in harsh alkaline media. Beside that
cost, environmental footprint of these desalination techniques are
significant; from damaging marine eco-system, to huge land use, to
discharge of tons of GHG and huge carbon footprint.
Other less energy consuming techniques based on membrane
separation are being sought to reduce both the carbon footprint and
operating costs is membrane distillation (MD).
Emerged in 1960s, MD is an alternative technology for water
desalination attracting more attention since 1980s. MD process
involves the evaporation of a hot feed, typically below boiling point
of brine at standard conditions, by creating a water vapor pressure
difference across the porous, hydrophobic membrane. Main
advantages of MD compared to other commercially available
technologies (MSF and MED) and specially RO are reduction of
membrane and module stress due to absence of trans-membrane
pressure, less impact of contaminant fouling on distillate due to
transfer of only water vapor, utilization of low grade or waste heat
from oil and gas industries to heat up the feed up to required
temperature difference across the membrane, superior water quality,
and relatively lower capital and operating cost.
To achieve the objective of this study, state of the art flat-sheet
cross-flow DCMD bench scale unit was designed, commissioned, and
tested. The objective of this study is to analyze the characteristics and
morphology of the membrane suitable for DCMD through SEM
imaging and contact angle measurement and to study the water
quality of distillate produced by DCMD bench scale unit.
Comparison with available literature data is undertaken where
appropriate and laboratory data is used to compare a DCMD distillate
quality with that of other desalination techniques and standards.
Membrane SEM analysis showed that the PTFE membrane used
for the study has contact angle of 127º with highly porous surface
supported with less porous and bigger pore size PP membrane. Study
on the effect of feed solution (salinity) and temperature on water
quality of distillate produced from ICP and IC analysis showed that
with any salinity and different feed temperature (up to 70ºC) the
electric conductivity of distillate is less than 5 μS/cm with 99.99%
salt rejection and proved to be feasible and effective process capable
of consistently producing high quality distillate from very high feed
salinity solution (i.e. 100000 mg/L TDS) even with substantial
quality difference compared to other desalination methods such as
RO and MSF.
Abstract: Finnish national research project, User- and Business-oriented Suburb Renovation Concept (KLIKK), was started in January 2012 and will end in June 2014. The perspective of energy efficiency is emphasised in the project, but also it addresses what improving the energy efficiency of suburban apartment buildings means from the standpoint of architecturally valuable buildings representing different periods. The project will also test the impacts of stricter energy efficiency requirements on renovation projects.
The primary goal of the project is to develop a user-oriented, industrial, economic renovation concept for suburban apartment building renovation, extension and construction of additional storeys. The concept will make it possible to change from performance- and cost-based operation to novel service- and user-oriented, site-specifically tailored renovation methods utilizing integrated order and delivery chains.
The present project is collaborating with Ministry of the Environment and participating cities in developing a new type of lighter town planning model for suburban renovations and in-fill construction. To support this, the project will simultaneously develop practices for environmental impact assessment tools in renovation and suburban supplementary and in-fill construction.
Abstract: Concentric bracing systems have been in practice for many years because of their effectiveness in reducing seismic response. Depending on concept, seismic design codes provide various response modification factors (R), which itself consists of different terms, for different types of lateral load bearing systems but configuration of these systems are often ignored in the proposed values. This study aims at considering the effect of different x-bracing diagonal configuration on values of ductility dependent term in R computation. 51 models were created and nonlinear push over analysis has been performed. The main variables of this study were the suitable location of X–bracing diagonal configurations, which establishes better nonlinear behavior in concentric braced steel frames. Results show that some x-bracing diagonal configurations improve the seismic performance of CBF significantly and explicit consideration of lateral load bearing systems seems necessary.
Abstract: The ice rink floor is the largest heat exchanger in an ice rink. The important part of the floor consists of concrete, and the thermophysical properties of this concrete have strong influence on the energy usage of the ice rink. The thermal conductivity of concrete can be increased by using iron ore as ballast. In this study, the Transient Plane Source (TPS) method showed an increase up to 58.2% of thermal conductivity comparing the improved concrete to standard concrete. Moreover, two alternative ice rink floor designs are suggested to incorporate the improved concrete. A 2D simulation was developed to investigate the temperature distribution in the conventional and the suggested designs. The results show that the suggested designs reduce the temperature difference between the ice surface and the brine by 1-4˚C, when comparing with convectional designs at equal heat flux. This primarily leads to an increased coefficient of performance (COP) in the primary refrigeration cycle and secondly to a decrease in the secondary refrigerant pumping power. The suggested designs have great potential to reduce the energy usage of ice rinks. Depending on the load scenario in the ice rink, the saving potential lies in the range of 3-10% of the refrigeration system energy usage. This calculation is based on steady state conditions and the potential with improved dynamic behavior is expected to increase the potential saving.
Abstract: This paper introduces a new generalization of the two parameter Weibull distribution. To this end, the quadratic rank transmutation map has been used. This new distribution is named exponentiated transmuted Weibull (ETW) distribution. The ETW distribution has the advantage of being capable of modeling various shapes of aging and failure criteria. Furthermore, eleven lifetime distributions such as the Weibull, exponentiated Weibull, Rayleigh and exponential distributions, among others follow as special cases. The properties of the new model are discussed and the maximum likelihood estimation is used to estimate the parameters. Explicit expressions are derived for the quantiles. The moments of the distribution are derived, and the order statistics are examined.
Abstract: Machine learning represents a set of topics dealing with the creation and evaluation of algorithms that facilitate pattern recognition, classification, and prediction, based on models derived from existing data. The data can present identification patterns which are used to classify into groups. The result of the analysis is the pattern which can be used for identification of data set without the need to obtain input data used for creation of this pattern. An important requirement in this process is careful data preparation validation of model used and its suitable interpretation. For breeders, it is important to know the origin of animals from the point of the genetic diversity. In case of missing pedigree information, other methods can be used for traceability of animal´s origin. Genetic diversity written in genetic data is holding relatively useful information to identify animals originated from individual countries. We can conclude that the application of data mining for molecular genetic data using supervised learning is an appropriate tool for hypothesis testing and identifying an individual.
Abstract: Three legumes i.e. soybean, kidney bean and mung
bean, and jojoba seed as an oil seed were processed into tempeh, a
fermented food. Changes in phytic acid, total phenols and trypsin
inhibitor were monitored during the pretreatments (soaking, soaking–
dehulling, washing and cooking) and fermentation with Rhizopus
oligosporus. Soaking was found to reduce total phenol and trypsin
inhibitor levels in soybean, kidney bean and mung bean. However,
phytic acid was reduced by soaking in kidney bean and mung bean.
Cooking was the most effective in reducing the activity of trypsin
inhibitor. During fermentation, a slight increase in the level of trypsin
inhibitor was noticed in soybean. Phytic acid and total phenols were
decreased during fermentation in soybean, kidney bean but mung
bean faild to form tempeh because the antifungal activity of herein a
protein in mung bean, which exerts both chitinase activity and
antifungal activity against a variety of fungal species. On the other
hand, solid- state fermentation of jojoba seeds was not effective in
reducing their content from cyanogenic glycosides (simmondsin).
Abstract: EU and UK Government targets for minimising and recycling household waste has led the responsible authorities to research the alternatives to landfill. In the work reported here the local waste collection authority (Charnwood Borough Council) has adopted the aspirational strategy of becoming a “Zero Waste Borough” to lead the drive for public participation. The work concludes that the separate collection of food waste would be needed to meet the two regulatory standards on recycling and biologically active wastes.
An analysis of a neighbouring Authority (Newcastle-Under-Lyne Borough Council (NBC), a similar sized local authority that has a successful weekly food waste collection service was undertaken. Results indicate that the main challenges for Charnwood Borough Council would be gaining householder co-operation, the extra costs of collection and organising alternative treatment. The analysis also demonstrated that there was potential offset value via anaerobic digestion for CBC to overcome these difficulties and improve its recycling performance.
Abstract: Concrete sewer pipes are known to suffer from a process of hydrogen sulfide gas induced sulfuric acid corrosion. This leads to premature pipe degradation, performance failure and collapses which in turn may lead to property and health damage. The above work reports on a field study undertaken in working sewer manholes where the parameters of effluent temperature and pH as well as ambient temperature and concentration of hydrogen sulfide were continuously measured over a period of two months. Early results suggest that effluent pH has no direct effect on hydrogen sulfide build up; on average the effluent temperature is 3.5°C greater than the ambient temperature inside the manhole and also it was observed that hydrogen sulfate concentration increases with increasing temperature.
Abstract: In this work we describe the preparation of NanoSilver/methylcellulose hydrogel containing silver nanoparticles (NPs) for topical bactericidal applications. Highly concentrated dispersion of silver NPs as high as of 5g/L of silver with diameter of 10nm was prepared by reduction of AgNO3 via strong reducing agent NaBH4. Silver NPs were stabilized by addition of sodium polyacrylate in order to prevent their aggregation at such high concentration. This way synthesized silver NPs were subsequently incorporated into methylcellulose suspension at elevated temperature resulting in formation of NanoSilver/methylcellulose hydrogel when temperature cooled down to laboratory conditions. In vitro antibacterial activity assay proved high bactericidal and fungicidal efficiency of silver NPs alone in the form of dispersion as well as in the form of hydrogel against broad spectrum of bacteria and yeasts including highly multiresistant strains such as methicillin-resistant Staphylococcus aureus. A very low concentrations of silver as low as 0.84mg/L Ag in as-prepared dispersion gave antibacterial performance. NanoSilver/methylcellulose hydrogel showed antibacterial action at the lowest used silver concentration equal to 25mg/L. Such prepared NanoSilver/methylcellulose hydrogel represent promising topical antimicrobial formulation for treatment of burns and wounds.
Abstract: Ammonium nitrate (AN) is produced by the reaction of ammonia and nitric acid, and a waste condensate is obtained. The condensate contains pure AN in concentration up to 10g/L. The salt content in the condensate is too high to discharge immediately into the river thus it must be treated. This study is concerned with the treatment of condensates from an industrial AN production by combination of electrodialysis (ED) and electrodeionization (EDI). The condensate concentration was in range 1.9–2.5g/L of AN. A pilot ED module with 25 membrane pairs following by a laboratory EDI module with 10 membrane pairs operated continuously during 800 hours. Results confirmed that the combination of ED and EDI is suitable for the condensate treatment.
Abstract: This action research accentuates the outcome of a development in English pronunciation, using principles of phonetics for English major students at Loei Rajabhat University. The research is split into 5 separate modules: 1) Organs of Speech and How to Produce Sounds, 2) Monopthongs, 3) Diphthongs, 4) Consonant sounds, and 5) Suprasegmental Features. Each module followed a 4 step action research process, 1) Planning, 2) Acting, 3) Observing, and 4) Reflecting. The research targeted 2nd year students who were majoring in English Education at Loei Rajabhat University during the academic year of 2011. A mixed methodology employing both quantitative and qualitative research was used, which put theory into action, taking segmental features up to suprasegmental features. Multiple tools were employed which included the following documents: pre-test and post-test papers, evaluation and assessment papers, group work assessment forms, a presentation grading form, an observation of participants form and a participant self-reflection form.
All 5 modules for the target group showed that results from the post-tests were higher than those of the pre-tests, with 0.01 statistical significance. All target groups attained results ranging from low to moderate and from moderate to high performance. The participants who attained low to moderate results had to re-sit the second round. During the first development stage, participants attended classes with group participation, in which they addressed planning through mutual co-operation and sharing of responsibility. Analytic induction of strong points for this operation illustrated that learner cognition, comprehension, application, and group practices were all present whereas the participants with weak results could be attributed to biological differences, differences in life and learning, or individual differences in responsiveness and self-discipline.
Participants who were required to be re-treated in Spiral 2 received the same treatment again. Results of tests from the 5 modules after the 2nd treatment were that the participants attained higher scores than those attained in the pre-test. Their assessment and development stages also showed improved results. They showed greater confidence at participating in activities, produced higher quality work, and correctly followed instructions for each activity. Analytic induction of strong and weak points for this operation remains the same as for Spiral 1, though there were improvements to problems which existed prior to undertaking the second treatment.
Abstract: Vibration analysis of most critical equipment is considered as one of the most challenging activities in preventive maintenance. Utilities are heart of the process in big industrial plants like petrochemical zones. Vibration analysis methods and condition monitoring systems of these kinds of equipments are developed too much in recent years. On the other hand, there are too much operation factors like inlet and outlet pressures and temperatures that should be monitored. In this paper, some of the most effective concepts and techniques related to gas turbine vibration analysis are discussed. In addition, a gas turbine SIEMENS 162MW - V94.2 vibration case history related to Iran power industry in Fars province is explained. Vibration monitoring system and machinery technical specification are introduced. Besides, absolute and relative vibration trends, turbine and compressor orbits, Fast Fourier transform (FFT) in absolute vibrations, vibration modal analysis, turbine and compressor start up and shut down conditions, bode diagrams for relative vibrations, Nyquist diagrams and waterfall or three-dimensional FFT diagrams in startup and trip conditions are discussed with relative graphs. Furthermore, Split Resonance in gas turbines is discussed in details. Moreover, some updated vibration monitoring system, blade manufacturing technique and modern damping mechanism are discussed in this paper.
Abstract: The acid attack on cement mortars modified with rubber aggregates and EVA polymer binder was studied. Mortar specimens were prepared using a type CEM I 42.5 Portland cement and siliceous sand, as well as by substituting 25% of sand with shredded used automobile tires, and by adding EVA polymer in two percentages (5% and 10% of cement mass). Some specimens were only air cured, at laboratory conditions, and their compressive strength and water absorption were determined. The rest specimens were stored in acid solutions (HCl, H2SO4, HNO3) after 28 days of initial curing, and stored at laboratory temperature. Compressive strength tests, mass measurements and visual inspection took place for 28 days. Compressive strength and water absorption of the air-cured specimens were significantly decreased when rubber aggregates are used. The addition of EVA polymer further reduced water absorption, while had no important impact on strength. Compressive strength values were affected in a greater extent by hydrochloric acid solution, followed by sulfate and nitric acid solutions. The addition of EVA polymer decreased compressive strength loss for the specimens with rubber aggregates stored in hydrochloric and nitric acid solutions. The specimens without polymer binder showed similar mass loss, which was higher in sulfate acid solution followed by hydrochloric and nitric acid solutions. The use of EVA polymer delayed mass loss, while its content did not affect it significantly.
Abstract: We propose obstacle classification method based on 2D
LIDAR Database. The existing obstacle classification method based
on 2D LIDAR, has an advantage in terms of accuracy and shorter
calculation time. However, it was difficult to classifier the type of
obstacle and therefore accurate path planning was not possible. In
order to overcome this problem, a method of classifying obstacle type
based on width data of obstacle was proposed. However, width data
was not sufficient to improve accuracy. In this paper, database was
established by width and intensity data; the first classification was
processed by the width data; the second classification was processed
by the intensity data; classification was processed by comparing to
database; result of obstacle classification was determined by finding
the one with highest similarity values. An experiment using an actual
autonomous vehicle under real environment shows that calculation
time declined in comparison to 3D LIDAR and it was possible to
classify obstacle using single 2D LIDAR.
Abstract: This paper presents a study on the effect of
second-order slip on forced convection through a long isoflux heated
or cooled planar microchannel. The fully developed solutions of flow
and thermal fields are analytically obtained on the basis of the
second-order Maxwell-Burnett slip and local heat flux boundary
conditions. Results reveal that when the average flow velocity
increases or the wall heat flux amount decreases, the role of thermal
creep becomes more insignificant, while the effect of second-order slip
becomes larger. The second-order term in the Deissler slip boundary
condition is found to contribute a positive velocity slip and then to lead
to a lower pressure drop as well as a lower temperature rise for the
heated-wall case or to a higher temperature rise for the cooled-wall
case. These findings are contrary to predictions made by the
Karniadakis slip model.
Abstract: The aim of this paper is to assess the influence of several indicators determining innovativeness of countries' economies by applying selected soft computing methods. Such methods enable us to identify correlations between indicators for period 2006-2010. The main attention in the paper is focused on selecting proper computer tools for solving this problem. As a tool supporting identification, the X-means clustering algorithm, the Apriori rules generation algorithm as well as Self-Organizing Feature Maps (SOMs) have been selected. The paper has rather a rudimentary character. We briefly describe usefulness of the selected approaches and indicate some challenges for further research.
Abstract: The problem of estimating a proportion has important
applications in the field of economics, and in general, in many areas
such as social sciences. A common application in economics is
the estimation of the headcount index. In this paper, we define the
general headcount index as a proportion. Furthermore, we introduce
a new quantitative method for estimating the headcount index. In
particular, we suggest to use the logistic regression estimator for the
problem of estimating the headcount index. Assuming a real data set,
results derived from Monte Carlo simulation studies indicate that the
logistic regression estimator can be more accurate than the traditional
estimator of the headcount index.
Abstract: The aim of this research is to explore how pupils in art classes can use creative digital art tools to redesign Tamazight fonts, in order to develop children’s artistic creativity, enable them to learn about a new culture, and to help the teacher assess the creativity of pupils in the art class. It can also help students to improve their talents in drawing. The study could relate to research in Libya among the Amazigh people (better known as Berber) and possibly the development of Tamazight fonts with new uses in art. The research involved students aged 9-10 years old working with digital art tools, and was designed to explore the potential of digital technology by discovering suitable tools and techniques to develop children’s artistic performance using Tamazight fonts. The project also sought to show the aesthetic aspects of these characters and to stimulate the artistic creativity of these young people.
Abstract: Distributed generation units (DGs) are grid-connected or stand-alone electric generation units located within the electric distribution system at or near the end user. It is generally accepted that centralized electric power plants will remain the major source of the electric power supply for the near future. DGs, however, can complement central power by providing incremental capacity to the utility grid or to an end user. This paper presents an efficient power dispatching model for hybrid wind-Solar power generation system, to satisfy some essential requirements, such as dispersed electric power demand, electric power quality and reducing generation cost and so on. In this paper, presented some elements of the main parts in the hybrid system; and then made fundamental dispatching strategies according to different situations; then pointed out four improving measures to improve genetic algorithm, such as: modify the producing way of selection probability, improve the way of crossover, protect excellent chromosomes, and change mutation range and so on. Finally, propose a technique for solving the unit's commitment for dispatching problem based on an improved genetic algorithm.