Abstract: In this paper, snow samples containing dust particles
from several sampling points around the city of Ostrava were
analyzed. The pH values of sampled snow were measured and solid
particles analyzed. Particle size, zeta potential and content of selected
heavy metals were determined in solid particles. The pH values of
most samples lay in the slightly acid region. Mean values of particle
size ranged from 290.5 to 620.5 nm. Zeta potential values varied
between -5 and -26.5 mV. The following heavy metal concentration
ranges were found: copper 0.08-0.75 mg/g, lead 0.05-0.9 mg/g,
manganese 0.45-5.9 mg/g and iron 25.7-280.46 mg/g. The highest
values of copper and lead were found in the vicinity of busy
crossroads, and on the contrary, the highest levels of manganese and
iron were detected close to a large steelworks. The proportion
between pH values, zeta potentials, particle sizes and heavy metal
contents was established. Zeta potential decreased with rising pH
values and, simultaneously, heavy metal content in solid particles
increased. At the same time, higher metal content corresponded to
lower particle size.
Abstract: This study was conducted to evaluate the manganese
removal from aqueous solution using Banana peels activated carbon
(BPAC). Batch experiments have been carried out to determine the
influence of parameters such as pH, biosorbent dose, initial metal ion
concentrations and contact times on the biosorption process. From
these investigations, a significant increase in percentage removal of
manganese 97.4% is observed at pH value 5.0, biosorbent dose 0.8 g,
initial concentration 20 ppm, temperature 25 ± 2°C, stirring rate 200
rpm and contact time 2h. The equilibrium concentration and the
adsorption capacity at equilibrium of the experimental results were
fitted to the Langmuir and Freundlich isotherm models; the Langmuir
isotherm was found to well represent the measured adsorption data
implying BPAC had heterogeneous surface. A raw groundwater
samples were collected from Baharmos groundwater treatment plant
network at Embaba and Manshiet Elkanater City/District-Giza,
Egypt, for treatment at the best conditions that reached at first phase
by BPAC. The treatment with BPAC could reduce iron and
manganese value of raw groundwater by 91.4% and 97.1%,
respectively and the effect of the treatment process on the
microbiological properties of groundwater sample showed decrease
of total bacterial count either at 22°C or at 37°C to 85.7% and 82.4%,
respectively. Also, BPAC was characterized using SEM and FTIR
spectroscopy.
Abstract: Amyloid aggregation of polypeptides is related to a
growing number of pathologic states known as amyloid disorders. In
recent years, blocking or reversing amyloid aggregation via the use of
small compounds are considered as two useful approaches in
hampering the development of these diseases. In this research, we
have compared the ability of several manganese-salen derivatives, as
synthetic compounds, and apigenin, as a natural flavonoid, to inhibit
of hen egg-white lysozyme (HEWL) aggregation, as an in vitro
model system.
Different spectroscopic analyses such as Thioflavin T (ThT) and
Anilinonaphthalene-8-sulfonic acid (ANS) fluorescence, Congo red
(CR) absorbance along with transmission electron microscopy were
used in this work to monitor the HEWL aggregation kinetic and
inhibition. Our results demonstrated that both type of compounds
were capable to prevent the formation of lysozyme amyloid
aggregation in vitro. In addition, our data indicated that synthetic
compounds had higher activity to inhibit of the β-sheet structures
relative to natural compound. Regarding the higher antioxidant
activities of the salen derivatives, it can be concluded that in addition
to aromatic rings of each of the compounds, the potent antioxidant
properties of salen derivatives contributes to lower lysozyme fibril
accumulation.
Abstract: Nowadays harmonization of sanitary and hygienic standards of environmental quality with international standards is crucial part of integration of Russia into the international community. Harmonization of Russian and international ambient air quality standards may be realized by risk-based standards development. In this paper approaches to risk-based standards development and examples of these approaches implementation are presented.
Abstract: The health and environmental risk of eating mushrooms grown in Abakaliki were evaluated in terms of heavy metals accumulation. Mushroom samples were collected from four different farms located at Izzi, Amajim, Amana and Amudo and analyzed for (iron, lead, manganese and cadmium) using Bulk Scientific Atomic Absorption Spectrophotometer 205. Results indicates mean range of concentrations of the trace metals in the mushrooms were Fe (0.22-152. 03), Mn (0.74-9.76), Pb (0.01.0.80), Cd (0.61-0.82) mg/L respectively. Accumulation of Cd on the four locations under investigation was higher than the UK Government Food Science Surveillance and World Health Organization maximum recommended levels in mushroom for human consumption. The Fe and Mn contaminants of Amudo were significant and show the impact of anthropogenic/atmospheric pollution. The potential sources of the heavy metals in the mushrooms were from urban waste, dust from mining and quarrying activities, natural geochemistry of the area, and use of inorganic fertilizers
Abstract: Mangabeira (Hancornia speciosa Gomes), a native plant in Brazil, is found growing spontaneously in various regions of the country. The high perishability of tropical fruits such as mangaba, causes it to be necessary to use technologies that promote conservation, aiming to increase the shelf life of this fruit and add value. The objective of this study was to compare the mangabas lyophilization curves behaviors with different sizes and maturation stages. The fruits were freeze-dried for a period of approximately 45 hours at lyophilizer Liotop brand, model L -108. It has been considered large the fruits between 38 and 58 mm diameter and small, between 23 and 28 mm diameter and the two states of maturation, intermediate and mature. Large size mangabas drying curves in both states of maturation were linear behavior at all process, while the kinetic drying curves related to small fruits, independent of maturation state, had a typical behavior of drying, with all the well-defined steps. With these results it was noted that the time of lyophilization was suitable for small mangabas, a fact that did not happen with the larger one. This may indicate that the large mangabas require a longer time to freeze until reaches the equilibrium level, as it happens with the small fruits, going to have constant moisture at the end of the process. For both types of fruit were analyzed water activity, acidity, protein, lipid, and vitamin C before and after the process.
Abstract: The aim of this research paper was based on an examination of sources of water supply and water quality for local consumption, conducted at eco- tourism villages of Suan Luang Sub- District Municipality of Amphawa District, Samut Songkram Province. The study incorporated both questionnaire and field work of water testing as the research tool and method. The sample size of 288 households was based on the population of the district, whereas the selected sample water sources were from 60 households: 30 samples were ground water and another 30 were surface water. Degree of heavy metal contamination in the water including copper, iron, manganese, zinc, cadmium and lead was investigated utilizing the Atomic Absorption- Direct Aspiration method. The findings unveiled that 96.0 percent of household water consumption was based on water supply, while the rest on canal, river and rain water. The household behavior of consumption revealed that 47.2 percent of people routinely consumed water without boiling or filtering prior to consumption. The investigation of water supply quality found that the degree of heavy metal contamination including metal, lead, iron, copper, manganese and cadmium met the standards of the Department of Health.
Abstract: This study aimed to evaluated the surface water quality for agriculture and consumption in the Amphawa District. The surface water quality parameters in this study included water temperature, turbidity, conductivity, salinity, pH, dissolved oxygen, BOD, nitrate, suspended solids, phosphorus, total dissolved solids (TDS), iron (Fe), copper (Cu), zinc (Zn), manganese (Mn), lead (Pb) and cadmium (Cd). The water samples were collected from small excavation, Lychee, Pomelo and Coconut orchards for 3 seasons from January to December 2011.
The surface water quality from small excavation, Lychee, pomelo and coconut orchards were met the type III of surface water quality standard. The concentration of heavy metal and did not differ significantly at 0.05 level, except dissolved oxygen.
The surface water was suitable for consumption by the usual sterile and generally improving water quality through the process before and was suitable for agriculture.
Abstract: Combustion of fuels in industrial and transport sector has lead to an alarming release of polluting gases to the atmosphere. Carbon monoxide is one such pollutant, which is formed as a result of incomplete oxidation of the fuel. In order to analyze the effect of catalyst on the reduction of CO emissions to the atmosphere, two catalysts Mn2O3 and Hopcalite are considered. A model was formed based on mass and energy balance equations. Results show that Hopcalite catalyst as compared to Mn2O3 catalyst helped in faster conversion of the polluting gas as the operating temperature of the hopcalite catalyst is much lower as compared to the operating temperature of Mn2O3 catalyst.
Abstract: The exponential increase in the volume of medical image database has imposed new challenges to clinical routine in maintaining patient history, diagnosis, treatment and monitoring. With the advent of data mining and machine learning techniques it is possible to automate and/or assist physicians in clinical diagnosis. In this research a medical image classification framework using data mining techniques is proposed. It involves feature extraction, feature selection, feature discretization and classification. In the classification phase, the performance of the traditional kNN k nearest neighbor classifier is improved using a feature weighting scheme and a distance weighted voting instead of simple majority voting. Feature weights are calculated using the interestingness measures used in association rule mining. Experiments on the retinal fundus images show that the proposed framework improves the classification accuracy of traditional kNN from 78.57 % to 92.85 %.
Abstract: In-situ chemical oxidation (ISCO) has been widely
used for source zone remediation of Dense Nonaqueous Phase
Liquids (DNAPLs) in subsurface environments. DNAPL source
zones for karst aquifers are generally located in epikarst where the
DNAPL mass is trapped either in karst soil or at the regolith contact
with carbonate bedrock. This study aims to investigate the
performance of oxidation of residual trichloroethylene found in such
environments by potassium permanganate. Batch and flow cell
experiments were conducted to determine the kinetics and the mass
removal rate of TCE. pH change, Cl production, TCE and MnO4
destruction were monitored routinely during experiments. Nonreactive
tracer tests were also conducted prior and after the oxidation
process to determine the influence of oxidation on flow conditions.
The results show that oxidant consumption rate of the calcareous
epikarst soil was significant and the oxidant demand was determined
to be 20 g KMnO4/kg soil. Oxidation rate of residual TCE (1.26x10-3
s-1) was faster than the oxidant consumption rate of the soil (2.54 -
2.92x10-4 s-1) at only high oxidant concentrations (> 40 mM
KMnO4). Half life of TCE oxidation ranged from 7.9 to 10.7 min.
Although highly significant fraction of residual TCE mass in the
system was destroyed by permanganate oxidation, TCE
concentration in the effluent remained above its MCL. Flow
interruption tests indicate that efficiency of ISCO was limited by the
rate of TCE dissolution and the rate-limited desorption of TCE. The
residence time and the initial concentration of the oxidant in the
source zone also controlled the efficiency of ISCO in epikarst.
Abstract: Impurity metals such as manganese and cadmium
from high-tenor cobalt electrolyte solution were selectively removed
by solvent extraction method using Co-D2EHPA after converting the functional group of D2EHPA with Co2+ ions. The process parameters
such as pH, organic concentration, O/A ratio, kinetics etc. were
investigated and the experiments were conducted by batch tests in the laboratory bench scale. Results showed that a significant amount
of manganese and cadmium can be extracted using Co-D2EHPA for the optimum processing of cobalt electrolyte solution at equilibrium pH about 3.5. The McCabe-Thiele diagram, constructed from the
extraction studies showed that 100% impurities can be extracted through four stages for manganese and three stages for cadmium
using O/A ratio of 0.65 and 1.0, respectively. From the stripping study, it was found that 100% manganese and cadmium can be stripped from the loaded organic using 0.4 M H2SO4 in a single
contact. The loading capacity of Co-D2EHPA by manganese and cadmium were also investigated with different O/A ratio as well as
with number of stages of contact of aqueous and organic phases. Valuable information was obtained for the designing of an impurities
removal process for the production of pure cobalt with less trouble in the electrowinning circuit.
Abstract: It is important to remove manganese from water
because of its effects on human and the environment. Human
activities are one of the biggest contributors for excessive manganese
concentration in the environment. The proposed method to remove
manganese in aqueous solution by using adsorption as in carbon
nanotubes (CNT) at different parameters: The parameters are CNT
dosage, pH, agitation speed and contact time. Different pHs are pH
6.0, pH 6.5, pH 7.0, pH 7.5 and pH 8.0, CNT dosages are 5mg,
6.25mg, 7.5mg, 8.75mg or 10mg, contact time are 10 min, 32.5 min,
55 min, 87.5 min and 120 min while the agitation speeds are 100rpm,
150rpm, 200rpm, 250rpm and 300rpm. The parameters chosen for
experiments are based on experimental design done by using Central
Composite Design, Design Expert 6.0 with 4 parameters, 5 levels and
2 replications. Based on the results, condition set at pH 7.0, agitation
speed of 300 rpm, 7.5mg and contact time 55 minutes gives the
highest removal with 75.5%. From ANOVA analysis in Design
Expert 6.0, the residual concentration will be very much affected by
pH and CNT dosage. Initial manganese concentration is 1.2mg/L
while the lowest residual concentration achieved is 0.294mg/L,
which almost satisfy DOE Malaysia Standard B requirement.
Therefore, further experiments must be done to remove manganese
from model water to the required standard (0.2 mg/L) with the initial
concentration set to 0.294 mg/L.
Abstract: A method of collecting composition data and examining structural features of pearlite lamellae and the parent austenite at the growth interface in a 13wt. % manganese steel has been demonstrated with the use of Scanning Transmission Electron Microscopy (STEM). The combination of composition data and the structural features observed at the growth interface show that available theories of pearlite growth cannot explain all the observations.
Abstract: Aim. We have introduced the notion of order to multinormed spaces and countable union spaces and their duals. The topology of bounded convergence is assigned to the dual spaces. The aim of this paper is to develop the theory of ordered topological linear
spaces La,b, L(w, z), the dual spaces of ordered multinormed spaces
La,b, ordered countable union spaces L(w, z), with the topology of bounded convergence assigned to the dual spaces. We apply Laplace transformation to the ordered linear space of Laplace transformable
generalized functions. We ultimately aim at finding solutions to nonhomogeneous
nth order linear differential equations with constant
coefficients in terms of generalized functions and comparing different
solutions evolved out of different initial conditions.
Method. The above aim is achieved by
• Defining the spaces La,b, L(w, z).
• Assigning an order relation on these spaces by identifying a
positive cone on them and studying the properties of the cone.
• Defining an order relation on the dual spaces La,b, L(w, z) of La,b, L(w, z) and assigning a topology to these dual spaces which makes the order dual and the topological dual the same. • Defining the adjoint of a continuous map on these spaces
and studying its behaviour when the topology of bounded
convergence is assigned to the dual spaces.
• Applying the two-sided Laplace Transformation on the ordered
linear space of generalized functions W and studying some
properties of the transformation which are used in solving
differential equations.
Result. The above techniques are applied to solve non-homogeneous
n-th order linear differential equations with constant coefficients in
terms of generalized functions and to compare different solutions of the differential equation.
Abstract: In this study, we sought to investigate the mercury
removal efficiency of manganese oxides from natural gas. The
fundamental studies on mercury removal with manganese oxides
sorbents were carried out in a laboratory scale fixed bed reactor at 30
°C with a mixture of methane (20%) and nitrogen gas laden with 4.8
ppb of elemental mercury. Manganese oxides with varying surface
area and crystalline phase were prepared by conventional precipitation
method in this study. The effects of surface area, crystallinity and
other metal oxides on mercury removal efficiency were investigated.
Effect of Ag impregnation on mercury removal efficiency was also
investigated. Ag supported on metal oxide such titania and zirconia as
reference materials were also used in this study for comparison. The
characteristics of mercury removal reaction with manganese oxide
was investigated using a temperature programmed desorption (TPD)
technique.
Manganese oxides showed very high Hg removal activity (about
73-93% Hg removal) for first time use. Surface area of the manganese
oxide samples decreased after heat-treatment and resulted in complete
loss of Hg removal ability for repeated use after Hg desorption in the
case of amorphous MnO2, and 75% loss of the initial Hg removal
activity for the crystalline MnO2. Mercury desorption efficiency of
crystalline MnO2 was very low (37%) for first time use and high (98%)
after second time use. Residual potassium content in MnO2 may have
some effect on the thermal stability of the adsorbed Hg species.
Desorption of Hg from manganese oxides occurs at much higher
temperatures (with a peak at 400 °C) than Ag/TiO2 or Ag/ZrO2.
Mercury may be captured on manganese oxides in the form of mercury
manganese oxide.
Abstract: The use of statistical data and of the neural networks, capable of elaborate a series of data and territorial info, have allowed the making of a model useful in the subdivision of urban places into homogeneous zone under the profile of a social, real estate, environmental and urbanist background of a city. The development of homogeneous zone has fiscal and urbanist advantages. The tools in the model proposed, able to be adapted to the dynamic changes of the city, allow the application of the zoning fast and dynamic.
Abstract: Metal cutting is a severe plastic deformation process
involving large strains, high strain rates, and high temperatures.
Conventional analysis of the chip formation process is based on bulk
material deformation disregarding the inhomogeneous nature of the
material microstructure. A series of orthogonal cutting tests of AISI
1045 and 1144 steel were conducted which yielded similar process
characteristics and chip formations. With similar shear angles and cut
chip thicknesses, shear strains for both chips were found to range
from 2.0 up to 2.8. The manganese-sulfide (MnS) precipitate in the
1144 steel has a very distinct and uniform shape which allows for
comparison before and after chip formation. From close observations
of MnS precipitates in the cut chips it is shown that the conventional
approach underestimates plastic strains in metal cutting.
Experimental findings revealed local shear strains around a value of
6. These findings and their implications are presented and discussed.
Abstract: Japan is known to be a technological powerhouse, being noted for its automobiles, consumer electronics, laptop computers, portable gaming devices, and more recently healing animal robots. Japan is also noted for its popular culture; manga, anime, novels, films, character goods, game programs, cosplay cafes, karaoke and so on. It may be natural for people outside Japan to assume that e-learning in Japan must be well advanced and innovative. In reality, the application of technologies in education in Japan is far behind of other developed countries. Especially in higher education, apathy of students towards their study prevails and teachers continue ignoring such student attitudes. E-learning, which is supposed to revolutionalize the way people learn as it has potentials to enable more student-centered learning, has not been realized in Japan and mostly used to perpetuate the teachercentered teaching in a different format.
Abstract: We succeeded to produce a high performance and flexible graphene/Manganese dioxide (G/MnO2) electrode coated on flexible polyethylene terephthalate (PET) substrate. The graphene film is initially synthesized by drop-casting the graphene oxide (GO) solution on the PET substrate, followed by simultaneous reduction and patterning of the dried film using carbon dioxide (CO2) laser beam with power of 1.8 W. Potentiostatic Anodic Deposition method was used to deposit thin film of MnO2 with different loading mass 10 – 50 and 100 μg.cm-2 on the pre-prepared graphene film. The electrodes were fully characterized in terms of structure, morphology, and electrochemical performance. A maximum specific capacitance of 973 F.g-1 was attributed when depositing 50μg.cm-2 MnO2 on the laser reduced graphene oxide rGO (or G/50MnO2) and over 92% of its initial capacitance was retained after 1000 cycles. The good electrochemical performance and long-term cycling stability make our proposed approach a promising candidate in the supercapacitor applications.