Abstract: Gas hydrates can agglomerate and block multiphase oil and gas pipelines when water is present at hydrate forming conditions. Using "Cold Flow Technology", the aim is to condition gas hydrates so that they can be transported as a slurry mixture without a risk of agglomeration. During the pipeline shut down however, hydrate particles may settle in bends and build hydrate plugs. An experimental setup has been designed and constructed to study the flow of such plugs at start up operations. Experiments have been performed using model fluid and model hydrate particles. The propagations of initial plugs in a bend were recorded with impedance probes along the pipe. The experimental results show a dispersion of the plug front. A peak in pressure drop was also recorded when the plugs were passing the bend. The evolutions of the plugs have been simulated by numerical integration of the incompressible mass balance equations, with an imposed mixture velocity. The slip between particles and carrier fluid has been calculated using a drag relation together with a particle-fluid force balance.
Abstract: A reliability, availability and maintainability (RAM) model has been built for acid gas removal plant for system analysis that will play an important role in any process modifications, if required, for achieving its optimum performance. Due to the complexity of the plant, the model was based on a Reliability Block Diagram (RBD) with a Monte Carlo simulation engine. The model has been validated against actual plant data as well as local expert opinions, resulting in an acceptable simulation model. The results from the model showed that the operation and maintenance can be further improved, resulting in reduction of the annual production loss.
Abstract: A novel sponge submerged membrane bioreactor
(SSMBR) was developed to effectively remove organics and
nutrients from wastewater. Sponge is introduced within the SSMBR
as a medium for the attached growth of biomass. This paper evaluates
the effects of new and acclimatized sponges for dissolved organic
carbon (DOC) removal from wastewater at different mixed liquor
suspended solids- (MLSS) concentration of the sludge. It was
observed in a series of experimental studies that the acclimatized
sponge performed better than the new sponge whilst the optimum
DOC removal could be achieved at 10g/L of MLSS with the
acclimatized sponge. Moreover, the paper analyses the relationships
between the MLSSsponge/MLSSsludge and the DOC removal efficiency
of SSMBR. The results showed a non-linear relationship between the
biomass parameters of the sponge and the sludge, and the DOC
removal efficiency of SSMBR. A second-order polynomial function
could reasonably represent these relationships.
Abstract: In this paper we study a system composed by carbon
nanotube (CNT) and bundle of carbon nanotube (BuCNT) interacting
with a specific fatty acid as molecular probe. Full system is
represented by open nanotube (or nanotubes) and the linoleic acid
(LA) relaxing due the interaction with CNT and BuCNT. The LA has
in his form an asymmetric shape with COOH termination provoking
a close BuCNT interaction mainly by van der Waals force field. The
simulations were performed by classical molecular dynamics with
standard parameterizations.
Our results show that these BuCNT and CNT are dynamically
stable and it shows a preferential interaction position with LA
resulting in three features: (i) when the LA is interacting with CNT
and BuCNT (including both termination, CH2 or COOH), the LA is
repelled; (ii) when the LA terminated with CH2 is closer to open
extremity of BuCNT, the LA is also repelled by the interaction
between them; and (iii) when the LA terminated with COOH is
closer to open extremity of BuCNT, the LA is encapsulated by the
BuCNT. These simulations are part of a more extensive work on
searching efficient selective molecular devices and could be useful to
reach this goal.
Abstract: Cooperative communication scheme can be substituted
for multiple-input multiple-output (MIMO) technique when it may
not be able to support multiple antennas due to size, cost or
hardware limitations. In other words, cooperative communication
scheme is an efficient method to achieve spatial diversity without
multiple antennas. For satisfaction of rising QoS, we propose a
reliable cooperative communication scheme with M-QAM based Dual
Carrier Modulation (M-DCM), which can increase diversity gain.
Although our proposed scheme is very simple method, it gives us
frequency and spatial diversity. Simulation result shows our proposed
scheme obtains diversity gain more than the conventional cooperative
communication scheme.
Abstract: Water has always been a very precious resource.
However, many of us do not fully understand or appreciate water-s
value until there will be a shortage. We intended to analyze the water
consumption into the Spanish households to understand their
behavior according to the habitants of the house. In this research was
carried out a survey of users, asking for water consumption of their
households. The aim of this paper is get a reference value of
consumers in Spanish households to help to check their bill and
realize if their consumption is excessive, including some tips to
decrease it.
Abstract: Failure in mastery of motor skills proficiency during
childhood has been seen as a detrimental factor for children to be
physically active. Lack of motor skills proficiency tends to reduce
children’s competency and confidence level to participate in physical
activity. As a consequence of less participation in physical activity,
children will turn to be overweight and obese. It has been suggested
that children who master motor skill proficiency will be more
involved in physical activity thus preventing them from being
overweight. Obesity has become a serious childhood health issues
worldwide. Previous studies have found that children who were
overweight and obese were generally less active however these
studies focused on one gender. This study aims to compare motor
skill proficiency of underweight, normal-weight, overweight and
obese young boys as well as to determine the relationship between
motor skills proficiency and body composition. 112 boys aged
between 8 to 10 years old participated in this study. Participants were
assigned to four groups; underweight, normal-weight, overweight and
obese using BMI-age percentile chart for children. Bruininks-
Oseretsky Test Second Edition-Short Form was administered to
assess their motor skill proficiency. Meanwhile, body composition
was determined by the skinfold thickness measurement. Result
indicated that underweight and normal children were superior in
motor skills proficiency compared to overweight and obese children
(p < 0.05). A significant strong inverse correlation between motor
skills proficiency and body composition (r = -0.849) is noted. The
findings of this study could be explained by non-contributory mass
that carried by overweight and obese children leads to biomechanical
movement inefficiency which will become detrimental to motor skills
proficiency. It can be concluded that motor skills proficiency is
inversely correlated with body composition.
Abstract: Most people know through experience and intuition what the word „sport“ means. Sport includes a combination of these configurations when it involves team competitions, tournaments, or matches in dual sports or individual sports. Sport management - it is an area of professional endeavor in which a variety of sport-related managerial careers exist and it is also an area of academic professional preparation. Exists three unique aspects of sport management: sport marketing, sport enterprise financial structures and sport industry career paths. The aim of the paper was to highlight the growing importance of sport in contemporary society, especially to emphasize its socio-economic benefits and refer to the development of sport management and marketing. The article has shown that sport contributes 2-3% to gross domestic product in the Czech Republic and that the demand for experts, specialists educated for the sports manager profession is growing.
Abstract: The Siemens Healthcare Sector is one of the world's
largest suppliers to the healthcare industry and a trendsetter in
medical imaging and therapy, laboratory diagnostics, medical
information technology, and hearing aids.
Siemens offers its customers products and solutions for the entire
range of patient care from a single source – from prevention and
early detection to diagnosis, and on to treatment and aftercare. By
optimizing clinical workflows for the most common diseases,
Siemens also makes healthcare faster, better, and more cost effective.
The optimization of clinical workflows requires a
multidisciplinary focus and a collaborative approach of e.g. medical
advisors, researchers and scientists as well as healthcare economists.
This new form of collaboration brings together experts with deep
technical experience, physicians with specialized medical knowledge
as well as people with comprehensive knowledge about health
economics.
As Charles Darwin is often quoted as saying, “It is neither the
strongest of the species that survive, nor the most intelligent, but the
one most responsive to change," We believe that those who can
successfully manage this change will emerge as winners, with
valuable competitive advantage.
Current medical information and knowledge are some of the core
assets in the healthcare industry. The main issue is to connect
knowledge holders and knowledge recipients from various
disciplines efficiently in order to spread and distribute knowledge.
Abstract: Fabrication and efficiency enhancement of non-mercury, high efficiency and green field emission lamps using carbon nano-materials such as carbon nanotubes as cathode field emitters was studied. Phosphor was coated on the ITO glass or metal substrates as the anode. The luminescence efficiency enhancement was carried out by upgrading the uniform of the emitters, improving electron and thermal conductivity of the phosphor and the optimization of the design of different cathode/anode configurations. After evaluation of the aforementioned parameters, the luminescence efficiency of the field emission lamps was raised.
Abstract: It is sometimes difficult to differentiate between
innocent murmurs and pathological murmurs during auscultation. In
these difficult cases, an intelligent stethoscope with decision support
abilities would be of great value. In this study, using a dog model,
phonocardiographic recordings were obtained from 27 boxer dogs
with various degrees of aortic stenosis (AS) severity. As a reference
for severity assessment, continuous wave Doppler was used. The data
were analyzed with recurrence quantification analysis (RQA) with
the aim to find features able to distinguish innocent murmurs from
murmurs caused by AS. Four out of eight investigated RQA features
showed significant differences between innocent murmurs and
pathological murmurs. Using a plain linear discriminant analysis
classifier, the best pair of features (recurrence rate and entropy)
resulted in a sensitivity of 90% and a specificity of 88%. In
conclusion, RQA provide valid features which can be used for
differentiation between innocent murmurs and murmurs caused by
AS.
Abstract: Falls are the primary cause of accidents in people over
the age of 65, and frequently lead to serious injuries. Since the early
detection of falls is an important step to alert and protect the aging
population, a variety of research on detecting falls was carried out
including the use of accelerators, gyroscopes and tilt sensors. In
exiting studies, falls were detected using an accelerometer with
errors. In this study, the proposed method for detecting falls was to
use two accelerometers to reject wrong falls detection. As falls are
accompanied by the acceleration of gravity and rotational motion, the
falls in this study were detected by using the z-axial acceleration
differences between two sites. The falls were detected by calculating
the difference between the analyses of accelerometers placed on two
different positions on the chest of the subject. The parameters of the
maximum difference of accelerations (diff_Z) and the integration of
accelerations in a defined region (Sum_diff_Z) were used to form the
fall detection algorithm. The falls and the activities of daily living
(ADL) could be distinguished by using the proposed parameters
without errors in spite of the impact and the change in the positions
of the accelerometers. By comparing each of the axial accelerations,
the directions of falls and the condition of the subject afterwards
could be determined.In this study, by using two accelerometers
without errors attached to two sites to detect falls, the usefulness of
the proposed fall detection algorithm parameters, diff_Z and
Sum_diff_Z, were confirmed.
Abstract: Solidification cracking and hydrogen cracking are some defects generated in the fusion welding of ultrahigh carbon steels. However, friction stir welding (FSW) of such steels, being a solid-state technique, has been demonstrated to alleviate such problems encountered in traditional welding. FSW include different process parameters that must be carefully defined prior processing. These parameters included but not restricted to: tool feed, tool RPM, tool geometry, tool tilt angle. These parameters form a key factor behind avoiding warm holes and voids behind the tool and in achieving a defect-free weld. More importantly, these parameters directly affect the microstructure of the weld and hence the final mechanical properties of weld. For that, 3D finite element (FE) thermo-mechanical model was developed using DEFORM 3D to simulate FSW of carbon steel. At points of interest in the joint, tracking is done for history of critical state variables such as temperature, stresses, and strain rates. Typical results found include the ability to simulate different weld zones. Simulations predictions were successfully compared to experimental FSW tests. It is believed that such a numerical model can be used to optimize FSW processing parameters to favor desirable defect free weld with better mechanical properties.
Abstract: Wireless ad hoc nodes are freely and dynamically
self-organize in communicating with others. Each node can act as
host or router. However it actually depends on the capability of
nodes in terms of its current power level, signal strength, number
of hops, routing protocol, interference and others. In this research,
a study was conducted to observe the effect of hops count over
different network topologies that contribute to TCP Congestion
Control performance degradation. To achieve this objective, a
simulation using NS-2 with different topologies have been
evaluated. The comparative analysis has been discussed based on
standard observation metrics: throughput, delay and packet loss
ratio. As a result, there is a relationship between types of topology
and hops counts towards the performance of ad hoc network. In
future, the extension study will be carried out to investigate the
effect of different error rate and background traffic over same
topologies.
Abstract: Delayed wound healing in diabetes is primarily
associated with hyperglycemia, over-expression of inflammatory
marker, oxidative stress and delayed collagen synthesis. This
unmanaged wound is producing high economic burden on the
society. Thus research is required to develop new and effective
treatment strategies to deal with this emerging issue. Our present
study incorporates the evaluation of wound healing effects of 50%
ethanol extract of Ocimum sanctum (OSE) in streptozotocin
(45mg/kg)-induced diabetic rats with concurrent wound ulcer. The
animals showing diabetes (Blood glucose level >140 and
Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: Compensating physiological motion in the context
of minimally invasive cardiac surgery has become an attractive
issue since it outperforms traditional cardiac procedures offering
remarkable benefits. Owing to space restrictions, computer vision
techniques have proven to be the most practical and suitable solution.
However, the lack of robustness and efficiency of existing methods
make physiological motion compensation an open and challenging
problem. This work focusses on increasing robustness and efficiency
via exploration of the classes of 1−and 2−regularized optimization,
emphasizing the use of explicit regularization. Both approaches are
based on natural features of the heart using intensity information.
Results pointed out the 1−regularized optimization class as the best
since it offered the shortest computational cost, the smallest average
error and it proved to work even under complex deformations.
Abstract: In recent years, environment regulation forcing
manufactures to consider recovery activity of end-of- life products
and/or return products for refurbishing, recycling,
remanufacturing/repair and disposal in supply chain management. In
this paper, a mathematical model is formulated for single product
production-inventory system considering remanufacturing/reuse of
return products and rate of return products follows a demand like
function, dependent on purchasing price and acceptance quality level.
It is useful in decision making to determine whether to go for
remanufacturing or disposal of returned products along with newly
produced products to satisfy a stationary demand. In addition, a
modified genetic algorithm approach is proposed, inspired by particle
swarm optimization method. Numerical analysis of the case study is
carried out to validate the model.
Abstract: The continued interest in the use of distributed generation in recent years is leading to the growth in number of distributed generators connected to distribution networks. Steady state voltage rise resulting from the connection of these generators can be a major obstacle to their connection at lower voltage levels. The present electric distribution network is designed to keep the customer voltage within tolerance limit. This may require a reduction in connectable generation capacity, under utilization of appropriate generation sites. Thus distribution network operators need a proper voltage regulation method to allow the significant integration of distributed generation systems to existing network. In this work a voltage rise problem in a typical distribution system has been studied. A method for voltage regulation of distribution system with multiple DG system by coordinated operation distributed generator, capacitor and OLTC has been developed. A sensitivity based analysis has been carried out to determine the priority for individual generators in multiple DG environment. The effectiveness of the developed method has been evaluated under various cases through simulation results.