Abstract: In the present research, the titanium-catalyzed
ethylene dimerization and more specifically, the concomitant byproducts
and polymer formation have been studied in the presence of 2,5-dimethoxytetrahydrofuran as an electron donor compound in the
combination with triethylaluminium (TEA) as activator. Then, we
added ethylene chlorobromide as a new efficient promoter to the
relevant catalyst system. Finally, the behavior of novel homogeneous
[Titanium tetrabutoxide (Ti(OC4H9)4)/2,5-dimethoxytetrahydrofuran/
TEA/ethylene chlorobromide] was investigated in the various
operating conditions for the optimum production of 1-butene. In the
optimum conditions, a very high ethylene conversion (almost 90.77
%), a relative high selectivity to 1-butene (79.00 %), yield of reaction equal to 71.70 % and a significant productivity (turnover frequency
equal to 1370 h-1) were achieved.
Abstract: This paper evaluates the performance of a novel
algorithm for tracking of a mobile node, interms of execution time
and root mean square error (RMSE). Particle Filter algorithm is used
to track the mobile node, however a new technique in particle filter
algorithm is also proposed to reduce the execution time. The
stationary points were calculated through trilateration and finally by
averaging the number of points collected for a specific time, whereas
tracking is done through trilateration as well as particle filter
algorithm. Wi-Fi signal is used to get initial guess of the position of
mobile node in x-y coordinates system. Commercially available
software “Wireless Mon" was used to read the WiFi signal strength
from the WiFi card. Visual Cµ version 6 was used to interact with
this software to read only the required data from the log-file
generated by “Wireless Mon" software. Results are evaluated through
mathematical modeling and MATLAB simulation.
Abstract: This paper presents the design, development and characterization of contractile water jet thruster (CWJT) for mini underwater robot. Instead of electric motor, this CWJT utilizes the Ionic Polymer Metal Composite (IPMC) as the actuator to generate the water jet. The main focus of this paper is to analyze the conceptual design of the proposed CWJT which would determine the thrust force value, jet flow behavior and actuator’s stress. Those thrust force and jet flow studies were carried out using Matlab/Simscape simulation software. The actuator stress had been analyzed using COSMOS simulation software. The results showed that there was no significant change for jet velocity at variable cross sectional nozzle area. However, a significant change was detected for jet velocity at different nozzle cross sectional area ratio which was up to 37%. The generated thrust force has proportional relation to the nozzle cross sectional area.
Abstract: Although, it is a long time that human know about
the importance of environment in life, but at the last decade of 20
century, the space that was full of hot scientific, collegial and
political were made in environmental challenge, So much that, this
problem not only disarrange the peace and security of life, but also it
has threatened human existence. One of the problems in last years
that are significant for authorities is unsatisfactory achieved results
against of using huge cost for magnificent environmental projects.
This subject leads thinker to this thought that for solving the
environmental problems it is needed new methods include of
sociology, ethics and philosophic, etc. methods apart of technical
affairs. Environment ethics is a new branch of philosophic ethics
discussion that discusses about the ethics relationship between
humans and universe that is around them. By notifying to the above
considered affairs, in today world, necessity of environmental ethics
for environment management is reduplicated. In the following the
article has been focused on environmental ethics role and
environmental management methods and techniques for developing
it.
Abstract: We have applied new accelerated algorithm for linear
discriminate analysis (LDA) in face recognition with support vector
machine. The new algorithm has the advantage of optimal selection
of the step size. The gradient descent method and new algorithm has
been implemented in software and evaluated on the Yale face
database B. The eigenfaces of these approaches have been used to
training a KNN. Recognition rate with new algorithm is compared
with gradient.
Abstract: The production and consumption of natural gas is on
the rise throughout the world as a result of its wide availability, ease
of transportation, use and clean-burning characteristics. The chief use
of ethane is in the chemical industry in the production of Ethene
(ethylene) by steam cracking. In this simulation, obtained ethane
recovery percent based on Gas sub-cooled process (GSP) is 99.9 by
mole that is included 32.1% by using de-methanizer column and
67.8% by de-ethanizer tower. The outstanding feature of this process
is the novel split-vapor concept that employs to generate reflux for
de-methanizer column. Remain amount of ethane in export gas cause
rise in gross heating value up to 36.66 MJ/Nm3 in order to use in
industrial and household consumptions.
Abstract: The quality improvements of the environmental
elements could increase the recreational opportunities in a certain
area (destination). The technique of the need for recreation focuses
on choosing certain destinations for recreational purposes. The basic
exchange taken into consideration is the one between the satisfaction
gained after staying in that area and the value expressed in money
and time allocated. The number of tourists in the respective area, the
duration of staying and the money spent including transportation
provide information on how individuals rank the place or certain
aspects of the area (such as the quality of the environmental
elements).
For the statistical analysis of the environmental benefits offered by
an area through the need of recreation technique, the following stages
are suggested:
- characterization of the reference area based on the
statistical variables considered;
- estimation of the environmental benefit through
comparing the reference area with other similar areas
(having the same environmental characteristics), from
the perspective of the statistical variables considered.
The model compared in recreation technique faced with a series of
difficulties which refers to the reference area and correct
transformation of time in money.
Abstract: This paper proposes rough set models with three
different level knowledge granules in incomplete information system
under tolerance relation by similarity between objects according to
their attribute values. Through introducing dominance relation on the
discourse to decompose similarity classes into three subclasses: little
better subclass, little worse subclass and vague subclass, it dismantles
lower and upper approximations into three components. By using
these components, retrieving information to find naturally hierarchical
expansions to queries and constructing answers to elaborative queries
can be effective. It illustrates the approach in applying rough set
models in the design of information retrieval system to access different
granular expanded documents. The proposed method enhances rough
set model application in the flexibility of expansions and elaborative
queries in information retrieval.
Abstract: The present research focus on the processing of mullite-based ceramics from oil refinery industrial wastes and byproducts of agricultural industry and on the investigating of silane modified surface of ceramics. Two waste products were used as initial material – waste aluminum oxide and waste rice husk. The burning - out additives used were waste rise husk. It is known that the oxide ceramics surface is hydrophilic due to the presence of – OH groups in it. The nature of ceramic surface regarding permeation of water and hydrocarbons can be changed by further treatment with silanes. The samples were studied mainly by X-ray analysis, FT-IR absorbance measurements and microscopic analysis. The X-ray analyses showed the phase composition depends on the firing temperature and on the purity of the starting alumina. Two kind of silanes were used for the transformation of surface from hydrophilic to hydrophobic – trimethoxymethylsilane (TMMS) and trimethylclorsilane (TMCS).
Abstract: A pilot plant for continuous flow microwave-assisted
chemical reaction combined with microreactors was developed and
water heating tests were conducted for evaluation of the developed
plant. We developed a microwave apparatus having a single
microwave generator that can heat reaction solutions in four reaction
fields simultaneously in order to increase throughput. We also
designed a four-branch waveguide using electromagnetic simulation,
and found that the transmission efficiency at 99%. Finally, we
developed the pilot plant using the developed microwave apparatus
and conducted water heating tests. The temperatures in the respective
reaction fields were controlled within ±1.1 K at 353.2 K. Moreover,
the energy absorption rates by the water were about 90% in the
respective reaction fields, whereas the energy absorption rate was
about 40% when 100 cm3 of water was heated by a commercially
available multimode microwave chemical reactor.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.
Abstract: Low-carbon economy means the energy conservation and emission reduction. How to measure and evaluate the regional low-carbon economy is an important problem which should be solved immediately. This paper proposed the eco-efficiency ratio based on the ecological efficiency to evaluate the current situation of the low-carbon economy in Jiangsu province and to analyze the efficiency of the low-carbon economy in Jiangsu and other provinces, compared both advantages and disadvantages. And then this paper put forward some advices for the government to formulate the correct development policy of low-carbon economy, to improve the technology innovation capacity and the efficiency of resource allocation.
Abstract: This paper deals with the project selection problem. Project selection problem is one of the problems arose firstly in the field of operations research following some production concepts from primary product mix problem. Afterward, introduction of managerial considerations into the project selection problem have emerged qualitative factors and criteria to be regarded as well as quantitative ones. To overcome both kinds of criteria, an analytic network process is developed in this paper enhanced with fuzzy sets theory to tackle the vagueness of experts- comments to evaluate the alternatives. Additionally, a modified version of Least-Square method through a non-linear programming model is augmented to the developed group decision making structure in order to elicit the final weights from comparison matrices. Finally, a case study is considered by which developed structure in this paper is validated. Moreover, a sensitivity analysis is performed to validate the response of the model with respect to the condition alteration.
Abstract: The network of delivering commodities has been an important design problem in our daily lives and many transportation applications. The delivery performance is evaluated based on the system reliability of delivering commodities from a source node to a sink node in the network. The system reliability is thus maximized to find the optimal routing. However, the design problem is not simple because (1) each path segment has randomly distributed attributes; (2) there are multiple commodities that consume various path capacities; (3) the optimal routing must successfully complete the delivery process within the allowable time constraints. In this paper, we want to focus on the design optimization of the Multi-State Flow Network (MSFN) for multiple commodities. We propose an efficient approach to evaluate the system reliability in the MSFN with respect to randomly distributed path attributes and find the optimal routing subject to the allowable time constraints. The delivery rates, also known as delivery currents, of the path segments are evaluated and the minimal-current arcs are eliminated to reduce the complexity of the MSFN. Accordingly, the correct optimal routing is found and the worst-case reliability is evaluated. It has been shown that the reliability of the optimal routing is at least higher than worst-case measure. Two benchmark examples are utilized to demonstrate the proposed method. The comparisons between the original and the reduced networks show that the proposed method is very efficient.
Abstract: Naive Bayes Nearest Neighbor (NBNN) and its variants, i,e., local NBNN and the NBNN kernels, are local feature-based classifiers that have achieved impressive performance in image classification. By exploiting instance-to-class (I2C) distances (instance means image/video in image/video classification), they avoid quantization errors of local image descriptors in the bag of words (BoW) model. However, the performances of NBNN, local NBNN and the NBNN kernels have not been validated on video analysis. In this paper, we introduce these three classifiers into human action recognition and conduct comprehensive experiments on the benchmark KTH and the realistic HMDB datasets. The results shows that those I2C based classifiers consistently outperform the SVM classifier with the BoW model.
Abstract: Cellular automata have been used for design of cryptosystems. Recently some secret sharing schemes based on linear memory cellular automata have been introduced which are used for both text and image. In this paper, we illustrate that these secret sharing schemes are vulnerable to dishonest participants- collusion. We propose a cheating model for the secret sharing schemes based on linear memory cellular automata. For this purpose we present a novel uniform model for representation of all secret sharing schemes based on cellular automata. Participants can cheat by means of sending bogus shares or bogus transition rules. Cheaters can cooperate to corrupt a shared secret and compute a cheating value added to it. Honest participants are not aware of cheating and suppose the incorrect secret as the valid one. We prove that cheaters can recover valid secret by removing the cheating value form the corrupted secret. We provide methods of calculating the cheating value.
Abstract: Heavy metals have bad effects on environment and
soils and it can uptake by natural HAP .natural Hap is an inexpensive
material that uptake large amounts of various heavy metals like Zn
(II) .Natural HAP (N-HAP), extracted from bovine cortical bone ash,
is a good choice for substitution of commercial HAP. Several
experiments were done to investigate the sorption capacity of Zn (II)
to N-HAP in various particles sizes, temperatures, initial
concentrations, pH and reaction times. In this study, the sorption of
Zinc ions from a Zn solution onto HAP particles with sizes of 1537.6
nm and 47.6 nm at three initial pH values of 4.50, 6.00 and 7.50 was
studied. The results showed that better performance was obtained
through a 47.6 nm particle size and higher pH values. The
experimental data were analyzed using Langmuir, Freundlich, and
Arrhenius equations for equilibrium, kinetic and thermodynamic
studies. The analysis showed a maximum adsorption capacity of NHAP
as being 1.562 mmol/g at a pH of 7.5 and small particle size.
Kinetically, the prepared N-HAP is a feasible sorbent that retains Zn
(II) ions through a favorable and spontaneous sorption process.
Abstract: Home is important for Chinese people. Because the
information regarding the house attributes and surrounding
environments is incomplete in most real estate agency, most house
buyers are difficult to consider the overall factors effectively and only
can search candidates by sorting-based approach. This study aims to
develop a decision support system for housing purchasing, in which
surrounding facilities of each house are quantified. Then, all
considered house factors and customer preferences are incorporated
into Simple Multi-Attribute Ranking Technique (SMART) to support
the housing evaluation. To evaluate the validity of proposed approach,
an empirical study was conducted from a real estate agency. Based on
the customer requirement and preferences, the proposed approach can
identify better candidate house with consider the overall house
attributes and surrounding facilities.
Abstract: Composite laminates are relatively weak in out of
plane loading, inter-laminar stress, stress concentration near the edge
and stress singularities. This paper develops a new analytical
formulation for laminated composite rotating disc fabricated from
symmetric sequential quasi isotropic layers to predict three
dimensional stress and deformation. This analysis is necessary to
evaluate mechanical integrity of fiber reinforced multi-layer
laminates used for high speed rotating applications such as high
speed impellers. Three dimensional governing equations are written
for rotating composite disc. Explicit solution is obtained with
"Frobenius" expansion series. Based on analytical results, there are
two separate zones of three dimensional stress fields in centre and
edge of rotating disc. For thin discs, out of plane deformations and
stresses are small in comparison with plane ones. For relatively thick
discs deformation and stress fields are three dimensional.