Abstract: This paper presents a real-time defect detection
algorithm for high-speed steel bar in coil. Because the target speed is
very high, proposed algorithm should process quickly the large
volumes of image for real-time processing. Therefore, defect detection
algorithm should satisfy two conflicting requirements of reducing the
processing time and improving the efficiency of defect detection. To
enhance performance of detection, edge preserving method is
suggested for noise reduction of target image. Finally, experiment
results show that the proposed algorithm guarantees the condition of
the real-time processing and accuracy of detection.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: This paper investigates the robust stability of uncertain neutral system with time-varying delay. By using Lyapunov method and linear matrix inequality technology, new delay-dependent stability criteria are obtained and formulated in terms of linear matrix inequalities (LMIs), which can be easy to check the robust stability of the considered systems. Numerical examples are given to indicate significant improvements over some existing results.
Abstract: This paper proposes an improvement method of classification
efficiency in a classification model. The model is used
in a risk search system and extracts specific labels from articles
posted at bulletin board sites. The system can analyze the important
discussions composed of the articles. The improvement method
introduces ensemble learning methods that use multiple classification
models. Also, it introduces expressions related to the specific labels
into generation of word vectors. The paper applies the improvement
method to articles collected from three bulletin board sites selected
by users and verifies the effectiveness of the improvement method.
Abstract: Fractional delay FIR filters design method based on
the differential evolution algorithm is presented. Differential evolution
is an evolutionary algorithm for solving a global optimization problems in the continuous search space. In the proposed approach,
an evolutionary algorithm is used to determine the coefficients of
a fractional delay FIR filter based on the Farrow structure. Basic
differential evolution is enhanced with a restricted mating technique,
which improves the algorithm performance in terms of convergence
speed and obtained solution. Evolutionary optimization is carried out by minimizing an objective function which is based on the amplitude
response and phase delay errors. Experimental results show that the proposed algorithm leads to a reduction in the amplitude response and phase delay errors relative to those achieved with the Least-Squares
method.
Abstract: Truss optimization problem has been vastly studied
during the past 30 years and many different methods have been
proposed for this problem. Even though most of these methods
assume that the design variables are continuously valued, in reality,
the design variables of optimization problems such as cross-sectional
areas are discretely valued. In this paper, an improved hill climbing
and an improved simulated annealing algorithm have been proposed
to solve the truss optimization problem with discrete values for crosssectional
areas. Obtained results have been compared to other
methods in the literature and the comparison represents that the
proposed methods can be used more efficiently than other proposed
methods
Abstract: This paper aims to explain the project carried out at
the University of Cordoba, specifically at the High Polytechnic
School in collaboration with two other organizations belonging to the
Andalusian Ministry of Innovation, Science and Business:
Andalusian Innovation and Development Agency (IDEA agency) [1]
and the Territorial Net of Entrepreneurship Support (in Spanish Red
Territorial de Apoyo al Emprendedor) [11].
The project is being developed in several stages of which only the
first one has already been completed. However, several important
preliminary results derive from it, based mainly in the description of
the nature of entrepreneurship in the field of university education and
its impact on student-s competency as recommended by the European
Higher Education Area. Some problems holding back the correct
future development will also be shown as derived from the specific
context of application of the project.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: This article experimentally investigates the
thermal performance of thermoelectric air-cooling module
which comprises a thermoelectric cooler (TEC) and an
air-cooling heat sink. The influences of input current and heat
load are determined. And performances under each situation
are quantified by thermal resistance analysis. Since TEC
generates Joule heat, this nature makes construction of thermal
resistance network difficult. To simplify the analysis, this
article emphasizes on the resistance heat load might meet when
passing through the device. Therefore, the thermal resistances
in this paper are to divide temperature differences by heat load.
According to the result, there exists an optimum input current
under every heating power. In this case, the optimum input
current is around 6A or 7A. The performance of the heat sink
would be improved with TEC under certain heating power and
input current, especially at a low heat load. According to the
result, the device can even make the heat source cooler than the
ambient. However, TEC is not always effective at every heat
load and input current. In some situation, the device works
worse than the heat sink without TEC. To determine the
availability of TEC, this study figures out the effective
operating region in which the TEC air-cooling module works
better than the heat sink without TEC. The result shows that
TEC is more effective at a lower heat load. If heat load is too
high, heat sink with TEC will perform worse than without TEC.
The limit of this device is 57W. Besides, TEC is not helpful if
input current is too high or too low. There is an effective range
of input current, and the range becomes narrower when the heat
load grows.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The algorithm represents the DCT coefficients to concentrate signal energy and proposes combination and dictator to eliminate the correlation in the same level subband for encoding the DCT-based images. This work adopts DCT and modifies the SPIHT algorithm to encode DCT coefficients. The proposed algorithm also provides the enhancement function in low bit rate in order to improve the perceptual quality. Experimental results indicate that the proposed technique improves the quality of the reconstructed image in terms of both PSNR and the perceptual results close to JPEG2000 at the same bit rate.
Abstract: A high performance computer includes a fast
processor and millions bytes of memory. During the data processing,
huge amount of information are shuffled between the memory and
processor. Because of its small size and its effectiveness speed, cache
has become a common feature of high performance computers.
Enhancing cache performance proved to be essential in the speed up
of cache-based computers. Most enhancement approaches can be
classified as either software based or hardware controlled. The
performance of the cache is quantified in terms of hit ratio or miss
ratio. In this paper, we are optimizing the cache performance based
on enhancing the cache hit ratio. The optimum cache performance is
obtained by focusing on the cache hardware modification in the way
to make a quick rejection to the missed line's tags from the hit-or
miss comparison stage, and thus a low hit time for the wanted line in
the cache is achieved. In the proposed technique which we called
Even- Odd Tabulation (EOT), the cache lines come from the main
memory into cache are classified in two types; even line's tags and
odd line's tags depending on their Least Significant Bit (LSB). This
division is exploited by EOT technique to reject the miss match line's
tags in very low time compared to the time spent by the main
comparator in the cache, giving an optimum hitting time for the
wanted cache line. The high performance of EOT technique against
the familiar mapping technique FAM is shown in the simulated
results.
Abstract: This paper presents an interval-based multi-attribute
decision making (MADM) approach in support of the decision
process with imprecise information. The proposed decision
methodology is based on the model of linear additive utility function
but extends the problem formulation with the measure of composite
utility variance. A sample study concerning with the evaluation of
electric generation expansion strategies is provided showing how the
imprecise data may affect the choice toward the best solution and
how a set of alternatives, acceptable to the decision maker (DM),
may be identified with certain confidence.
Abstract: The job shop scheduling problem (JSSP) is well known as one of the most difficult combinatorial optimization problems. This paper presents a hybrid genetic algorithm for the JSSP with the objective of minimizing makespan. The efficiency of the genetic algorithm is enhanced by integrating it with a local search method. The chromosome representation of the problem is based on operations. Schedules are constructed using a procedure that generates full active schedules. In each generation, a local search heuristic based on Nowicki and Smutnicki-s neighborhood is applied to improve the solutions. The approach is tested on a set of standard instances taken from the literature and compared with other approaches. The computation results validate the effectiveness of the proposed algorithm.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: Graph based image segmentation techniques are
considered to be one of the most efficient segmentation techniques
which are mainly used as time & space efficient methods for real
time applications. How ever, there is need to focus on improving the
quality of segmented images obtained from the earlier graph based
methods. This paper proposes an improvement to the graph based
image segmentation methods already described in the literature. We
contribute to the existing method by proposing the use of a weighted
Euclidean distance to calculate the edge weight which is the key
element in building the graph. We also propose a slight modification
of the segmentation method already described in the literature, which
results in selection of more prominent edges in the graph. The
experimental results show the improvement in the segmentation
quality as compared to the methods that already exist, with a slight
compromise in efficiency.
Abstract: In this article we are going to discuss the improvement
of the multi classes- classification problem using multi layer
Perceptron. The considered approach consists in breaking down the
n-class problem into two-classes- subproblems. The training of each
two-class subproblem is made independently; as for the phase of test,
we are going to confront a vector that we want to classify to all two
classes- models, the elected class will be the strongest one that won-t
lose any competition with the other classes. Rates of recognition
gotten with the multi class-s approach by two-class-s decomposition
are clearly better that those gotten by the simple multi class-s
approach.
Abstract: Logistics outsourcing is a growing trend and measuring its performance, a challenge. It must be consistent with the objectives set for logistics outsourcing, but we have found no objective-based performance measurement system. We have conducted a comprehensive review of the specialist literature to cover this gap, which has led us to identify and define these objectives. The outcome is that we have obtained a list of the most relevant objectives and their descriptions. This will enable us to analyse in a future study whether the indicators used for measuring logistics outsourcing performance are consistent with the objectives pursued with the outsourcing. If this is not the case, a proposal will be made for a set of financial and operational indicators to measure performance in logistics outsourcing that take the goals being pursued into account.
Abstract: PARADIGMA (PARticipative Approach to DIsease
Global Management) is a pilot project which aims to develop and
demonstrate an Internet based reference framework to share scientific
resources and findings in the treatment of major diseases.
PARADIGMA defines and disseminates a common methodology and
optimised protocols (Clinical Pathways) to support service functions
directed to patients and individuals on matters like prevention, posthospitalisation
support and awareness. PARADIGMA will provide a
platform of information services - user oriented and optimised
against social, cultural and technological constraints - supporting the
Health Care Global System of the Euro-Mediterranean Community
in a continuous improvement process.
Abstract: The objective of this study was to improve our
understanding of vulnerability and environmental change; it's causes
basically show the intensity, its distribution and human-environment
effect on the ecosystem in the Apodi Valley Region, This paper is
identify, assess and classify vulnerability and environmental change
in the Apodi valley region using a combined approach of landscape
pattern and ecosystem sensitivity. Models were developed using the
following five thematic layers: Geology, geomorphology, soil,
vegetation and land use/cover, by means of a Geographical
Information Systems (GIS)-based on hydro-geophysical parameters.
In spite of the data problems and shortcomings, using ESRI-s ArcGIS
9.3 program, the vulnerability score, to classify, weight and combine
a number of 15 separate land cover classes to create a single indicator
provides a reliable measure of differences (6 classes) among regions
and communities that are exposed to similar ranges of hazards.
Indeed, the ongoing and active development of vulnerability
concepts and methods have already produced some tools to help
overcome common issues, such as acting in a context of high
uncertainties, taking into account the dynamics and spatial scale of
asocial-ecological system, or gathering viewpoints from different
sciences to combine human and impact-based approaches. Based on
this assessment, this paper proposes concrete perspectives and
possibilities to benefit from existing commonalities in the
construction and application of assessment tools.