Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: This paper presents a new strategy of identification
and classification of pathological voices using the hybrid method
based on wavelet transform and neural networks. After speech
acquisition from a patient, the speech signal is analysed in order to
extract the acoustic parameters such as the pitch, the formants, Jitter,
and shimmer. Obtained results will be compared to those normal and
standard values thanks to a programmable database. Sounds are
collected from normal people and patients, and then classified into
two different categories. Speech data base is consists of several
pathological and normal voices collected from the national hospital
“Rabta-Tunis". Speech processing algorithm is conducted in a
supervised mode for discrimination of normal and pathology voices
and then for classification between neural and vocal pathologies
(Parkinson, Alzheimer, laryngeal, dyslexia...). Several simulation
results will be presented in function of the disease and will be
compared with the clinical diagnosis in order to have an objective
evaluation of the developed tool.
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: I/O workload is a critical and important factor to
analyze I/O pattern and file system performance. However tracing I/O
operations on the fly distributed parallel file system is non-trivial due
to collection overhead and a large volume of data. In this paper, we
design and implement a parallel file system logging method for high
performance computing using shared memory-based multi-layer
scheme. It minimizes the overhead with reduced logging operation
response time and provides efficient post-processing scheme through
shared memory. Separated logging server can collect sequential logs
from multiple clients in a cluster through packet communication.
Implementation and evaluation result shows low overhead and high
scalability of this architecture for high performance parallel logging
analysis.
Abstract: Aluminum salt that is generally presents as a solid
phase in the water purification sludge (WPS) can be dissolved,
recovering a liquid phase, by adding strong acid to the sludge solution.
According to the reaction kinetics, when reactant is in the form of
small particles with a large specific surface area, or when the reaction
temperature is high, the quantity of dissolved aluminum salt or
reaction rate, respectively are high. Therefore, in this investigation,
water purification sludge (WPS) solution was treated with ultrasonic
waves to break down the sludge, and different acids (1 N HCl and 1 N
H2SO4) were used to acidify it. Acid dosages that yielded the solution
pH of less than two were used. The results thus obtained indicate that
the quantity of dissolved aluminum in H2SO4-acidified solution
exceeded that in HCl-acidified solution. Additionally, ultrasonic
treatment increased the rate of dissolution of aluminum and the
amount dissolved. The quantity of aluminum dissolved at 60℃ was 1.5
to 2.0 times higher than that at 25℃.
Abstract: The visualization of geographic information on mobile devices has become popular as the widespread use of mobile Internet. The mobility of these devices brings about much convenience to people-s life. By the add-on location-based services of the devices, people can have an access to timely information relevant to their tasks. However, visual analysis of geographic data on mobile devices presents several challenges due to the small display and restricted computing resources. These limitations on the screen size and resources may impair the usability aspects of the visualization applications. In this paper, a variable-scale visualization method is proposed to handle the challenge of small mobile display. By merging multiple scales of information into a single image, the viewer is able to focus on the interesting region, while having a good grasp of the surrounding context. This is essentially visualizing the map through a fisheye lens. However, the fisheye lens induces undesirable geometric distortion in the peripheral, which renders the information meaningless. The proposed solution is to apply map generalization that removes excessive information around the peripheral and an automatic smoothing process to correct the distortion while keeping the local topology consistent. The proposed method is applied on both artificial and real geographical data for evaluation.
Abstract: Packet switched data network like Internet, which has
traditionally supported throughput sensitive applications such as email
and file transfer, is increasingly supporting delay-sensitive
multimedia applications such as interactive video. These delaysensitive
applications would often rather sacrifice some throughput
for better delay. Unfortunately, the current packet switched network
does not offer choices, but instead provides monolithic best-effort
service to all applications. This paper evaluates Class Based Queuing
(CBQ), Coordinated Earliest Deadline First (CEDF), Weighted
Switch Deficit Round Robin (WSDRR) and RED-Boston scheduling
schemes that is sensitive to delay bound expectations for variety of
real time applications and an enhancement of WSDRR is proposed.
Abstract: A simple and easy algorithm is presented for a fast calculation of kernel functions which required in fluid simulations using the Smoothed Particle Hydrodynamic (SPH) method. Present proposed algorithm improves the Linked-list algorithm and adopts the Pair-Wise Interaction technique, which are widely used for evaluating kernel functions in fluid simulations using the SPH method. The algorithm is easy to be implemented without any complexities in programming. Some benchmark examples are used to show the simulation time saved by using the proposed algorithm. Parametric studies on the number of divisions for sub-domains, smoothing length and total amount of particles are conducted to show the effectiveness of the present technique. A compact formulation is proposed for practical usage.
Abstract: AAM (active appearance model) has been successfully
applied to face and facial feature localization. However, its performance is sensitive to initial parameter values. In this paper, we propose a two-stage AAM for robust face alignment, which first fits an
inner face-AAM model to the inner facial feature points of the face and then localizes the whole face and facial features by optimizing the
whole face-AAM model parameters. Experiments show that the proposed face alignment method using two-stage AAM is more reliable to the background and the head pose than the standard
AAM-based face alignment method.
Abstract: The motion of a sphere moving along the axis of a
rotating viscous fluid is studied at high Reynolds numbers and
moderate values of Taylor number. The Higher Order Compact
Scheme is used to solve the governing Navier-Stokes equations. The
equations are written in the form of Stream function, Vorticity
function and angular velocity which are highly non-linear, coupled
and elliptic partial differential equations. The flow is governed by
two parameters Reynolds number (Re) and Taylor number (T). For
very low values of Re and T, the results agree with the available
experimental and theoretical results in the literature. The results are
obtained at higher values of Re and moderate values of T and
compared with the experimental results. The results are fourth order
accurate.
Abstract: In this paper, we analyze the rotor eddy currents losses provoqued by the stator slot harmonics developed in the permanent magnets or pole pieces of synchronous machines. An analytical approach is presented to evaluate the effect of slot ripples on rotor field and losses calculation. This analysis is then tested on a model by 2D/3D finite element (FE) calculation. The results show a good agreement on loss calculations when skin effect is negligible and the magnet is considered.
Abstract: Polymer-like organic thin films were deposited on both
aluminum alloy type 6061 and glass substrates at room temperature by
Plasma Enhanced Chemical Vapor Deposition (PECVD) methodusing
benzene and hexamethyldisiloxane (HMDSO) as precursor materials.
The surface and physical properties of plasma-polymerized organic
thin films were investigated at different r.f. powers. The effects of
benzene/argon ratio on the properties of plasma polymerized benzene
films were also investigated. It is found that using benzene alone
results in a non-coherent and non-adherent powdery deposited
material. The chemical structure and surface properties of the asgrown
plasma polymerized thin films were analyzed on glass
substrates with FTIR and contact angle measurements. FTIR spectra
of benzene deposited film indicated that the benzene rings are
preserved when increasing benzene ratio and/or decreasing r.f.
powers. FTIR spectra of HMDSO deposited films indicated an
increase of the hydrogen concentration and a decrease of the oxygen
concentration with the increase of r.f. power. The contact angle (θ) of
the films prepared from benzene was found to increase by about 43%
as benzene ratio increases from 10% to 20%. θ was then found to
decrease to the original value (51°) when the benzene ratio increases
to 100%. The contact angle, θ, for both benzene and HMDSO
deposited films were found to increase with r.f. power. This signifies
that the plasma polymerized organic films have substantially low
surface energy as the r.f power increases. The corrosion resistance of
aluminum alloy substrate both bare and covered with plasma
polymerized thin films was carried out by potentiodynamic
polarization measurements in standard 3.5 wt. % NaCl solution at
room temperature. The results indicate that the benzene and HMDSO
deposited films are suitable for protection of the aluminum substrate
against corrosion. The changes in the processing parameters seem to
have a strong influence on the film protective ability. Surface
roughness of films deposited on aluminum alloy substrate was
investigated using scanning electron microscopy (SEM). The SEM
images indicate that the surface roughness of benzene deposited films
increase with decreasing the benzene ratio. SEM images of benzene
and HMDSO deposited films indicate that the surface roughness
decreases with increasing r.f. power. Studying the above parameters
indicate that the films produced are suitable for specific practical
applications.
Abstract: As the information age matures, major social
infrastructures such as communication, finance, military and energy,
have become ever more dependent on information communication
systems. And since these infrastructures are connected to the Internet,
electronic intrusions such as hacking and viruses have become a new
security threat. Especially, disturbance or neutralization of a major
social infrastructure can result in extensive material damage and social
disorder. To address this issue, many nations around the world are
researching and developing various techniques and information
security policies as a government-wide effort to protect their
infrastructures from newly emerging threats. This paper proposes an
evaluation method for information security levels of CIIP (Critical
Information Infrastructure Protection), which can enhance the security
level of critical information infrastructure by checking the current
security status and establish security measures accordingly to protect
infrastructures effectively.
Abstract: The hidden-point bar method is useful in many
surveying applications. The method involves determining the
coordinates of a hidden point as a function of horizontal and vertical
angles measured to three fixed points on the bar. Using these
measurements, the procedure involves calculating the slant angles,
the distances from the station to the fixed points, the coordinates of
the fixed points, and then the coordinates of the hidden point. The
propagation of the measurement errors in this complex process has
not been fully investigated in the literature. This paper evaluates the
effect of the bar geometry on the position accuracy of the hidden
point which depends on the measurement errors of the horizontal and
vertical angles. The results are used to establish some guidelines
regarding the inclination angle of the bar and the location of the
observed points that provide the best accuracy.
Abstract: Soursop (Anona muricata) is one of the underutilized tropical fruits containing nutrients, particularly dietary fibre and antioxidant properties that are beneficial to human health. This objective of this study is to investigate the feasibility of matured soursop pulp flour (SPF) to be substituted with high-protein wheat flour in bread. Bread formulation was substituted with different levels of SPF (0%, 5%, 10% and 15%). The effect on physicochemical properties and sensory attributes were evaluated. Higher substitution level of SPF resulted in significantly higher (p
Abstract: This paper proposes a bi-objective model for the
facility location problem under a congestion system. The idea of the
model is motivated by applications of locating servers in bank
automated teller machines (ATMS), communication networks, and so
on. This model can be specifically considered for situations in which
fixed service facilities are congested by stochastic demand within
queueing framework. We formulate this model with two perspectives
simultaneously: (i) customers and (ii) service provider. The
objectives of the model are to minimize (i) the total expected
travelling and waiting time and (ii) the average facility idle-time.
This model represents a mixed-integer nonlinear programming
problem which belongs to the class of NP-hard problems. In addition,
to solve the model, two metaheuristic algorithms including nondominated
sorting genetic algorithms (NSGA-II) and non-dominated
ranking genetic algorithms (NRGA) are proposed. Besides, to
evaluate the performance of the two algorithms some numerical
examples are produced and analyzed with some metrics to determine
which algorithm works better.
Abstract: Time series models have been used to make predictions of academic enrollments, weather, road accident, casualties and stock prices, etc. Based on the concepts of quartile regression models, we have developed a simple time variant quantile based fuzzy time series forecasting method. The proposed method bases the forecast using prediction of future trend of the data. In place of actual quantiles of the data at each point, we have converted the statistical concept into fuzzy concept by using fuzzy quantiles using fuzzy membership function ensemble. We have given a fuzzy metric to use the trend forecast and calculate the future value. The proposed model is applied for TAIFEX forecasting. It is shown that proposed method work best as compared to other models when compared with respect to model complexity and forecasting accuracy.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: Simulations play a major role in education not only because they provide realistic models with which students can interact to acquire real world experiences, but also because they constitute safe environments in which students can repeat processes without any risk in order to perceive easier concepts and theories. Virtual reality is widely recognized as a significant technological advance that can facilitate learning process through the development of highly realistic 3D simulations supporting immersive and interactive features. The objective of this paper is to analyze the influence of virtual reality-s use in chemistry instruction as well as to present an integrated web-based learning environment for the simulation of chemical experiments. The proposed application constitutes a cost-effective solution for both schools and universities without appropriate infrastructure and a valuable tool for distance learning and life-long education in chemistry. Its educational objectives are the familiarization of students with the equipment of a real chemical laboratory and the execution of virtual volumetric analysis experiments with the active participation of students.
Abstract: The conventional GA combined with a local search
algorithm, such as the 2-OPT, forms a hybrid genetic algorithm(HGA)
for the traveling salesman problem (TSP). However, the geometric
properties which are problem specific knowledge can be used to
improve the search process of the HGA. Some tour segments (edges)
of TSPs are fine while some maybe too long to appear in a short tour.
This knowledge could constrain GAs to work out with fine tour
segments without considering long tour segments as often.
Consequently, a new algorithm is proposed, called intelligent-OPT
hybrid genetic algorithm (IOHGA), to improve the GA and the 2-OPT
algorithm in order to reduce the search time for the optimal solution.
Based on the geometric properties, all the tour segments are assigned
2-level priorities to distinguish between good and bad genes. A
simulation study was conducted to evaluate the performance of the
IOHGA. The experimental results indicate that in general the IOHGA
could obtain near-optimal solutions with less time and better accuracy
than the hybrid genetic algorithm with simulated annealing algorithm
(HGA(SA)).