Abstract: Natural fibers are used in polymer composites to
improve mechanical properties to replace inorganic reinforcing
agents produced by non-renewable resources. The present study
investigates the tensile and flexural behaviors of palm fibers-high
density polyethylene (HDPE) composite as a function of volume
fraction. The surface of the fibers was treated by mercerization
treatments to improve the wetting behavior of the apolar HDPE. The
treatment characterization was obtained by scanning electron
microscopy, X-Ray diffraction and infrared spectroscopy. Results
evidences that a good adhesion interfacial between fibers-matrix
caused an increase strength and modulus flexural as well as tensile
strength in the modified fibers/HDPE composites when compared to
the pure HDPE and untreated fibers reinforced composites.
Abstract: This research studies the joint production,
maintenance and subcontracting control policy for an unreliable
deteriorating manufacturing system. Production activities are
controlled by a derivation of the Hedging Point Policy, and given that
the system is subject to deterioration, it reduces progressively its
capacity to satisfy product demand. Multiple deterioration effects are
considered, reflected mainly in the quality of the parts produced and
the reliability of the machine. Subcontracting is available as support
to satisfy product demand; also, overhaul maintenance can be
conducted to reduce the effects of deterioration. The main objective
of the research is to determine simultaneously the production,
maintenance and subcontracting rate, which minimize the total,
incurred cost. A stochastic dynamic programming model is
developed and solved through a simulation-based approach
composed of statistical analysis and optimization with the response
surface methodology. The obtained results highlight the strong
interactions between production, deterioration and quality, which
justify the development of an integrated model. A numerical example
and a sensitivity analysis are presented to validate our results.
Abstract: The first laboratory synthesis of hard materials such as
diamond proceeded to attack of developing materials with high
hardness to compete diamond. Boron rich solids are good candidates
owing to their short interatomic bond lengths and strong covalent
character. Boron containing hard material was synthesized by modifiedmicrowave
method under nitrogen atmosphere by using a fuel
(glycine or urea), amorphous boron and/or boric acid in appropriate
molar ratio. Characterizations were done by x-ray diffraction (XRD),
Fourier transform infrared (FTIR) spectroscopy, scanning electron
microscopy/energy dispersive analyze (SEM/EDS), thermo
gravimetric/differential thermal analysis (TG/DTA).
Abstract: The aim of this study was to investigate the
photocatalytic activity of polycrystalline phases of bismuth tungstate
of formula Bi2WO6. Polycrystalline samples were elaborated using a
coprecipitation technique followed by a calcination process at
different temperatures (300, 400, 600 and 900°C). The obtained
polycrystalline phases have been characterized by X-ray diffraction
(XRD), scanning electron microscopy (SEM), and transmission
electron microscopy (TEM). Crystal cell parameters and cell volume
depend on elaboration temperature. High-resolution electron
microscopy images and image simulations, associated with X-ray
diffraction data, allowed confirming the lattices and space groups
Pca21. The photocatalytic activity of the as-prepared samples was
studied by irradiating aqueous solutions of Rhodamine B, associated
with Bi2WO6 additives having variable crystallite sizes. The
photocatalytic activity of such bismuth tungstates increased as the
crystallite sizes decreased. The high specific area of the
photocatalytic particles obtained at 300°C seems to condition the
degradation kinetics of RhB.
Abstract: The effect of carbon nanofibers (CNFs) on the
electrical properties of Poly(vinylidene fluoride-hexafluoropropylene)
(P(VdF-HFP)) based gel polymer electrolytes has been investigated
in the present work. The length and diameter ranges of CNFs used in
the present work are 5-50 μm and 200-600 nm respectively. The
nanocomposite gel polymer electrolytes have been synthesized by
solution casting technique with varying CNFs content in terms of
weight percentage. Electrochemical impedance analysis demonstrates
that the reinforcement of carbon nanofibers significantly enhances the
ionic conductivity of the polymer electrolyte. The decrease of
crystallinity of P(VdF-HFP) due the addition of CNFs has been
confirmed by X-ray diffraction (XRD). The interaction of CNFs with
various constituents of nanocomposite gel polymer electrolytes has
been assessed by Fourier Transform Infrared (FTIR) spectroscopy.
Moreover CNFs added gel polymer electrolytes offer superior
thermal stability as compared to that of CNFs free electrolytes as
confirmed by Thermogravimetric analysis (TGA).
Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: In this paper, we study the optical nonlinearities of
Silver sulfide (Ag2S) nanostructures dispersed in the Dimethyl
sulfoxide (DMSO) under exposure to 532 nm, 15 nanosecond (ns)
pulsed laser irradiation. Ultraviolet–visible absorption spectrometry
(UV-Vis), X-ray diffraction (XRD), and transmission electron
microscopy (TEM) are used to characterize the obtained nanocrystal
samples. The band gap energy of colloid is determined by analyzing
the UV–Vis absorption spectra of the Ag2S NPs using the band
theory of semiconductors. Z-scan technique is used to characterize
the optical nonlinear properties of the Ag2S nanoparticles (NPs).
Large enhancement of two photon absorption effect is observed with
increase in concentration of the Ag2S nanoparticles using open Zscan
measurements in the ns laser regime. The values of the nonlinear
absorption coefficients are determined based on the local nonlinear
responses including two photon absorption. The observed aperture
dependence of the Ag2S NP limiting performance indicates that the
nonlinear scattering plays an important role in the limiting action of
the sample. The concentration dependence of the optical liming is
also investigated. Our results demonstrate that the optical limiting
threshold decreases with increasing the silver sulfide NPs in DMSO.
Abstract: This study intends to show the influence of the
hydrolytic degradation on the properties of the e-PTFE/NOMEX®
membranes used in fire-protective clothing. The modification of
water vapour permeability, morphology and chemical structure was
examined by MOCON Permatran, electron microscopy scanning
(SEM), and ATR-FTIR, respectively. A decrease in permeability to
water vapour of the aged samples was observed following closure of
transpiration pores. Analysis of fiber morphology indicates the
appearance of defects at the fibers surface with the presence of micro
cavities. ATR-FTIR analysis reveals the presence of a new absorption
band attributed to carboxylic acid terminal groups generated during
the amide bond hydrolysis.
Abstract: Ecological systems are exposed and are influenced by
various natural and anthropogenic disturbances. They produce
various effects and states seeking response symmetry to a state of
global phase coherence or stability and balance of their food webs.
This research project addresses the development of a computational
methodology for modeling plankton food webs. The use of
algorithms to establish connections, the generation of representative
fuzzy multigraphs and application of technical analysis of complex
networks provide a set of tools for defining, analyzing and evaluating
community structure of coastal aquatic ecosystems, beyond the
estimate of possible external impacts to the networks. Thus, this
study aims to develop computational systems and data models to
assess how these ecological networks are structurally and
functionally organized, to analyze the types and degree of
compartmentalization and synchronization between oscillatory and
interconnected elements network and the influence of disturbances on
the overall pattern of rhythmicity of the system.
Abstract: Cole-Cole parameters of 40 post-menopausal women
are compared with their DEXA bone mineral density measurements.
Impedance characteristics of four extremities are compared; left and
right extremities are statistically same, but lower extremities are
statistically different than upper ones due to their different fat
content. The correlation of Cole-Cole impedance parameters to bone
mineral density (BMD) is observed to be higher for dominant arm.
With the post-menopausal population, ANOVA tests of the dominant
arm characteristic frequency, as a predictor for DEXA classified
osteopenic and osteoporic population around lumbar spine, is
statistically very significant. When used for total lumbar spine
osteoporosis diagnosis, the area under the Receiver Operating Curve
of the characteristic frequency is 0.830, suggesting that the Cole-Cole
plot characteristic frequency could be a useful diagnostic parameter
when integrated into standard screening methods for osteoporosis.
Moreover, the characteristic frequency can be directly measured by
monitoring frequency driven angular behavior of the dominant arm
without performing any complex calculation.
Abstract: Graphene was dispersed using a tip sonicator and the
effect of surfactants were analysed. Sodium Dodecyl Sulphate (SDS)
and Polyvinyl Alcohol (PVA) were compared to observe whether or
not they had any effect on any de-wrinkling, and secondly whether
they aided to achieve better dispersions. There is a huge demand for
wrinkle free graphene as this will greatly increase its usefulness in
various engineering applications. A comprehensive literature on dewrinkling
graphene has been discussed. Low magnification Scanning
Electronic Microscopy (SEM) was conducted to assess the quality of
graphene de-wrinkling. The utilization of the PVA has significant
effect on de-wrinkling whereas SDS had minimal effect on the dewrinkling
of graphene.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: In this research, thorium dioxide mesoporous
nanocrystalline powder was synthesized through the sol-gel method
using hydrated thorium nitrate and ammonium hydroxide as starting
materials and Triton X100 as surfactant. ThO2 gel was characterized
by thermogravimetric (TGA), and prepared ThO2 powder was
subjected to scanning electron microscopy (SEM), X-ray diffraction
(XRD), and Brunauer-Emett-Teller (BET) analyses studies. Detailed
analyses show that prepared powder consisted of phase with the
space group Fm3m of thoria and its crystalline size was 12.6 nm. The
thoria possesses 16.7 m2/g surface area and the pore volume and size
calculated to be 0.0423 cc/g and 1.947 nm, respectively.
Abstract: Conductivity properties of DNA molecule is
investigated in a simple, but chemically specific approach that is
intimately related to the Su-Schrieffer-Heeger (SSH) model. This
model is a tight-binding linear nanoscale chain. We have tried to
study the electrical current flowing in DNA and investigated the
characteristic I-V diagram. As a result, It is shown that there are the
(quasi-) ohmic areas in I-V diagram. On the other hand, the regions
with a negative differential resistance (NDR) are detectable in
diagram.
Abstract: There is currently a gap in the technology covering the
rapid establishment of control after a reconfiguration in a
Reconfigurable Manufacturing System. This gap involves the
detection of the factory floor state and the communication link
between the factory floor and the high-level software. In this paper, a
thin, hardware-supported Middleware Management System (MMS) is
proposed and its design and implementation are discussed. The
research found that a cost-effective localization technique can be
combined with intelligent software to speed up the ramp-up of a
reconfigured system. The MMS makes the process more intelligent,
more efficient and less time-consuming, thus supporting the
industrial implementation of the RMS paradigm.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.
Abstract: This report presents an alternative technique of
application of contrast agent in vivo, i.e. before sampling. By this
new method the electron micrograph of tissue sections have an
acceptable contrast compared to other methods and present no artifact
of precipitation on sections. Another advantage is that a small amount
of contrast is needed to get a good result given that most of them are
expensive and extremely toxic.
Abstract: Coal tar is a liquid by-product of coal pyrolysis
processes. This liquid oil mixture contains various kinds of useful
compounds such as benzoic aromatic compounds and phenolic
compounds. These compounds are widely used as raw material for
insecticides, dyes, medicines, perfumes, coloring matters, and many
others. The coal tar was collected by pyrolysis process of coal
obtained from PT Kaltim Prima Coal and Arutmin-Kalimantan. The
experiments typically occurred at the atmospheric pressure in a
laboratory furnace at temperatures ranging from 300 to 550oC with a
heating rate of 10oC/min and a holding time of 1 hour at the pyrolysis
temperature. The Gas Chromatography-Mass Spectroscopy (GC-MS)
was used to analyze the coal tar components. The obtained coal tar
has the viscosity of 3.12 cp, the density of 2.78 g/cm3, the calorific
value of 11,048.44 cal/g, and the molecular weight of 222.67. The
analysis result showed that the coal tar contained more than 78
chemical compounds such as benzene, cresol, phenol, xylene,
naphtalene, etc. The total phenolic compounds contained in coal tar
are 33.25% (PT KPC) and 17.58% (Arutmin-Kalimantan). The total
naphtalene compounds contained in coal tar is 14.15% (PT KPC) and
17.13% (Arutmin-Kalimantan).
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: This paper presents results of the survey regarding the
awareness about HIV/AIDS among HIV-infected individuals. A
questionnaire covering various aspects of HIV-infection was
conducted among 110 HIV-infected individuals who attended the
G.A. Zaharyan Moscow Tuberculosis Clinic, Department for
treatment of TB patients with HIV. The questionnaire included
questions about modes of HIV transmission and preventive measures
against HIV/AIDS, as well as questions about age, gender, education
and employment status. The survey revealed that the respondents in
the whole had a good knowledge regarding modes of HIV
transmission and preventive measures against HIV/AIDS: about
83,6% male respondents and 85,7% female respondents gave an
accurate answers regarding the HIV-infection. However, the
overwhelming majority of the study participants, that is, 88,5% men
and 98% women, was quite ignorant about the risk of acquiring HIV
through saliva and toothbrush of HIV-infected individual. Though
that risk is rather insignificant, it is still biologically possible. And
this gap in knowledge needs to be filled. As the study showed another
point of concern was the fact, that despite the knowledge of HIV
transmission risk through unprotected sex about 40% percent of HIVpositive
men and 25% of HIV-positive women did not insist on using
condoms with their sexual partners. These findings indicate that there
are still some aspects about HIV-infection which needed to be
clarified and explained through more detailed and specific
educational programs.