Abstract: A solution methodology without using integral
transformation is proposed to develop analytical solutions for
transient heat conduction in nonuniform hollow cylinders with
time-dependent boundary condition at the outer surface. It is shown
that if the thermal conductivity and the specific heat of the medium
are in arbitrary polynomial function forms, the closed solutions of the
system can be developed. The influence of physical properties on the
temperature distribution of the system is studied. A numerical
example is given to illustrate the efficiency and the accuracy of the
solution methodology.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Background: Muscle Energy Techniques (MET) have
been widely used by manual therapists over the past years, but still
limited research validated its use and there was limited evidence to
substantiate the theories used to explain its effects. Objective: To
investigate the effect of Muscle Energy Technique (MET) on anterior
pelvic tilt in patients with lumbar spondylosis. Design: Randomized
controlled trial. Subjects: Thirty patients with anterior pelvic tilt from
both sexes were involved, aged between 35 to 50 years old and they
were divided into MET and control groups with 15 patients in each.
Methods: All patients received 3sessions/week for 4 weeks where the
study group received MET, Ultrasound and Infrared, and the control
group received U.S and I.R only. Pelvic angle was measured by
palpation meter, pain severity by the visual analogue scale and
functional disabilities by the Oswestry disability index. Results: Both
groups showed significant improvement in all measured variables.
The MET group was significantly better than the control group in
pelvic angle, pain severity, and functional disability as p-value were
(0.001, 0.0001, 0.0001) respectively. Conclusion and implication: the
study group fulfilled greater improvement in all measured variables
than the control group which implies that application of MET in
combination with U.S and I.R were more effective in improving
pelvic tilting angle, pain severity and functional disabilities than
using electrotherapy only.
Abstract: To evaluate the vigor of wheat seeds and stress of
premature aging effects on germination percentage, root length and
shoot length of five wheat cultivars that include Vynak, Karkheh,
Chamran, Star and Kavir which underwent a period of zero, two,
three, four days in terms of premature aging with 41°C temperature
and 100% relative humidity. Seed germination percentage, root
length and shoot length in these conditions were measured. This
experiment was conducted as a factorial completely randomized
design with four replications in laboratory conditions. The results
showed that each of aging treatments used in this experiment can be
used to detect differences in vigor of wheat varieties. Wheat cultivars
illustrated significant differences in germination percentage, root
length and shoot length in terms of premature aging. The wheat
cultivars; Astar and Vynak had maximum germination percentage
and Karkheh, respectively Kavir and Chamran had lowest percentage
of seed germination. Reactions of root and shoot length of wheat
cultivars was also different. The results showed that the seeds with a
stronger vigor affected less in premature aging condition and the
difference between the percentage of seed germination under normal
conditions and stress was significant and the seeds with the weaker
vigor were more sensitive to the premature aging stress and the
premature aging had more severe negative impact on seed vigor.
Abstract: This paper presents results of the survey regarding the
awareness about HIV/AIDS among HIV-infected individuals. A
questionnaire covering various aspects of HIV-infection was
conducted among 110 HIV-infected individuals who attended the
G.A. Zaharyan Moscow Tuberculosis Clinic, Department for
treatment of TB patients with HIV. The questionnaire included
questions about modes of HIV transmission and preventive measures
against HIV/AIDS, as well as questions about age, gender, education
and employment status. The survey revealed that the respondents in
the whole had a good knowledge regarding modes of HIV
transmission and preventive measures against HIV/AIDS: about
83,6% male respondents and 85,7% female respondents gave an
accurate answers regarding the HIV-infection. However, the
overwhelming majority of the study participants, that is, 88,5% men
and 98% women, was quite ignorant about the risk of acquiring HIV
through saliva and toothbrush of HIV-infected individual. Though
that risk is rather insignificant, it is still biologically possible. And
this gap in knowledge needs to be filled. As the study showed another
point of concern was the fact, that despite the knowledge of HIV
transmission risk through unprotected sex about 40% percent of HIVpositive
men and 25% of HIV-positive women did not insist on using
condoms with their sexual partners. These findings indicate that there
are still some aspects about HIV-infection which needed to be
clarified and explained through more detailed and specific
educational programs.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: Tool, Die and Mould-making (TDM) firms have been
known to play a pivotal role in the growth and development of the
manufacturing sectors in most economies. Their output contributes
significantly to the quality, cost and delivery speed of final
manufactured parts. Unfortunately, the South African Tool, Die and
Mould-making manufacturers have not been competing on the local
or global market in a significant way. This reality has hampered the
productivity and growth of the sector thus attracting intervention. The
paper explores the shortcomings South African toolmakers have to
overcome to restore their competitive position globally. Results from
a global benchmarking survey on the tooling sector are used to
establish a roadmap of what South African toolmakers can do to
become a productive, World Class force on the global market.
Abstract: Grains, including oats (Avena sativa L.), have been
recognized functional foods, because provide beneficial effect on the
health of the consumer and decrease the risk of various diseases. Oats
are good source of soluble fibre, essential amino acids, unsaturated
fatty acids, vitamins and minerals. Oat breeders have developed oat
varieties and improved yielding ability potential of oat varieties.
Therefore, the aim of investigation was to analyze the composition of
perspective oat varieties and breeding lines grains grown in different
conditions and evaluate functional properties. In the studied samples
content of protein, starch, β-glucans, total dietetic fibre, composition
of amino acids and vitamin E were determined. The results of
analysis showed that protein content depending of varieties ranged
9.70% to 17.30% total dietary fibre 13.66 g100g-1 to 30.17 g100g-1,
content of β-glucans 2.7 g100g-1 to 3.5 g100g-1, amount of
vitamin E (α-tocopherol) determined from 4 mgkg-1 to 9.9 mgkg-1.
The sums of essential amino acids in oat grain samples were
determined from 31.63 gkg-1 to 54.90 gkg-1. It is concluded that
amino acids composition of husked and naked oats grown in organic
or conventional conditions is close to optimal for human health.
Abstract: Nine Degrees of Freedom (9 DOF) systems are
already in development in many areas. In this paper, an integrated
pressure sensor is proposed that will make use of an already existing
monolithic 9 DOF inertial MEMS platform. Capacitive pressure
sensors can suffer from limited sensitivity for a given size of
membrane. This novel pressure sensor design increases the sensitivity
by over 5 times compared to a traditional array of square diaphragms
while still fitting within a 2 mm x 2 mm chip and maintaining a fixed
static capacitance. The improved design uses one large diaphragm
supported by pillars with fixed electrodes placed above the areas of
maximum deflection. The design optimization increases the
sensitivity from 0.22 fF/kPa to 1.16 fF/kPa. Temperature sensitivity
was also examined through simulation.
Abstract: This paper presents thermal annealing de-wetting
technique for the preparation of porous metal membrane for Thin
Film Encapsulation (TFE) application. Thermal annealing de-wetting
experimental results reveal that pore size formation in porous metal
membrane depend upon i.e. 1. The substrate at which metal is
deposited, 2. Melting point of metal used for porous metal cap layer
membrane formation, 3. Thickness of metal used for cap layer, 4.
Temperature used for formation of porous metal membrane. In order
to demonstrate this technique, Silver (Ag) was used as a metal for
preparation of porous metal membrane on amorphous silicon (a-Si)
and silicon oxide. The annealing of the silver thin film of various
thicknesses was performed at different temperature. Pores in porous
silver film were analyzed using Scanning Electron Microscope
(SEM). In order to check the usefulness of porous metal film for TFE
application, the porous silver film prepared on amorphous silicon (a-
Si) and silicon oxide was released using XeF2 and VHF, respectively.
Finally, guide line and structures are suggested to use this porous
membrane for robust TFE application.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: The purpose of this study is to determine the
relationship of anxiety level between male and female undergraduates
at a private university in Malaysia. Convenient sampling method used
in this study in which the students were selected based on the
grouping assigned by the faculty. There were 214 undergraduates
who registered the probability courses had participated in this study.
Mathematics Anxiety Rating Scale (MARS) was the instrument used
in study which used to determine students’ anxiety level towards
probability. Reliability and validity of instrument was done before the
major study was conducted. In the major study, students were given
briefing about the study conducted. Participation of this study was
voluntary. Students were given consent form to determine whether
they agree to participate in the study. Duration of two weeks was
given for students to complete the given online questionnaire. The
data collected will be analyzed using Statistical Package for the
Social Sciences (SPSS) to determine the level of anxiety. There were
three anxiety level, i.e., low, average and high. Students’ anxiety
level was determined based on their scores obtained compared with
the mean and standard deviation. If the scores obtained were below
mean and standard deviation, the anxiety level was low. If the scores
were at below and above the mean and between one standard
deviation, the anxiety level was average. If the scores were above the
mean and greater than one standard deviation, the anxiety level was
high. Results showed that both of genders were having average
anxiety level. Among low, average and high anxiety level, frequency
of males were found to be higher as compared to females. Hence, the
mean values obtained for males (M = 3.62) was higher than females
(M = 3.42). In order to be significant of anxiety level among the
gender, the p-value should be less than .05. The p-value obtained in
this study was .117. However, this value was greater than .05. Thus,
there was no significant difference of anxiety level among the gender.
In other words, there was no relationship of anxiety level with the
gender.
Abstract: The design of Reverse logistics Network has attracted
growing attention with the stringent pressures from both
environmental awareness and business sustainability. Reverse
logistical activities include return, remanufacture, disassemble and
dispose of products can be quite complex to manage. In addition,
demand can be difficult to predict, and decision making is one of the
challenges task in such network. This complexity has amplified the
need to develop an integrated architecture for product return as an
enterprise system. The main purpose of this paper is to design Multi
Agent System (MAS) architecture using the Prometheus
methodology to efficiently manage reverse logistics processes. The
proposed MAS architecture includes five types of agents: Gate
keeping Agent, Collection Agent, Sorting Agent, Processing Agent
and Disposal Agent which act respectively during the five steps of
reverse logistics Network.
Abstract: This paper introduces a boost converter with a new
active snubber cell. In this circuit, all of the semiconductor
components in the converter softly turns on and turns off with the
help of the active snubber cell. Compared to the other converters, the
proposed converter has advantages of size, number of components
and cost. The main feature of proposed converter is that the extra
voltage stresses do not occur on the main switches and main diodes.
Also, the current stress on the main switch is acceptable level.
Moreover, the proposed converter can operates under light load
conditions and wide input line voltage. In this study, the operating
principle of the proposed converter is presented and its operation is
verified with the Proteus simulation software for a 1 kW and 100 kHz
model.
Abstract: In this paper, we provided a literature survey on the
artificial stock problem (ASM). The paper began by exploring the
complexity of the stock market and the needs for ASM. ASM
aims to investigate the link between individual behaviors (micro
level) and financial market dynamics (macro level). The variety of
patterns at the macro level is a function of the AFM complexity. The
financial market system is a complex system where the relationship
between the micro and macro level cannot be captured analytically.
Computational approaches, such as simulation, are expected to
comprehend this connection. Agent-based simulation is a simulation
technique commonly used to build AFMs. The paper proceeds by
discussing the components of the ASM. We consider the roles
of behavioral finance (BF) alongside the traditionally risk-averse
assumption in the construction of agent’s attributes. Also, the
influence of social networks in the developing of agents interactions is
addressed. Network topologies such as a small world, distance-based,
and scale-free networks may be utilized to outline economic
collaborations. In addition, the primary methods for developing
agents learning and adaptive abilities have been summarized.
These incorporated approach such as Genetic Algorithm, Genetic
Programming, Artificial neural network and Reinforcement Learning.
In addition, the most common statistical properties (the stylized facts)
of stock that are used for calibration and validation of ASM are
discussed. Besides, we have reviewed the major related previous
studies and categorize the utilized approaches as a part of these
studies. Finally, research directions and potential research questions
are argued. The research directions of ASM may focus on the macro
level by analyzing the market dynamic or on the micro level by
investigating the wealth distributions of the agents.
Abstract: Nowadays, several research studies point up that an
active lifestyle is essential for physical and mental health benefits.
Mobile phones have greatly influenced people’s habits and attitudes
also in the way they exercise. Our research work is mainly focused on
investigating how to exploit mobile technologies to favour people’s
exertion experience. To this end, we developed an exertion framework
users can exploit through a real world mobile application, called
EverywhereSport Run (EWRun), designed to act as a virtual personal
trainer to support runners during their trainings. In this work, inspired
by both previous findings in the field of interaction design for people
with visual impairments, feedback gathered from real users of our
framework, and positive results obtained from two experimentations,
we present some new interaction facilities we designed to enhance
the interaction experience during a training. The positive obtained
results helped us to derive some interaction design recommendations
we believe will be a valid support for designers of future mobile
systems conceived to be used in circumstances where there are limited
possibilities of interaction.
Abstract: The development of electric vehicle batteries have
resulted in very high energy density lithium-ion batteries. However,
this progress is accompanied by the risk of thermal runaway, which
can result in serious accidents. Heat pipes are heat exchangers that
are suitable to be applied in electric vehicle battery thermal
management for their lightweight, compact size and do not require
external power supply. This paper aims to examine experimentally a
Flat Plate Loop Heat Pipe (FPLHP) performance as a heat exchanger
in thermal management system of lithium-ion battery for electric
vehicle application. The heat generation of the battery was simulated
using a cartridge heater. Stainless steel screen mesh was used as the
capillary wick. Distilled water, alcohol and acetone were used as
working fluids with a filling ratio of 60%. It was found that acetone
gives the best performance that produces thermal resistance of 0.22
W/°C with 50°C evaporator temperature at heat flux load of 1.61
W/cm2.
Abstract: To tackle the air pollution issues, Plug-in Hybrid
Electric Vehicles (PHEVs) are proposed as an appropriate solution.
Charging a large amount of PHEV batteries, if not controlled, would
have negative impacts on the distribution system. The control process
of charging of these vehicles can be centralized in parking lots that
may provide a chance for better coordination than the individual
charging in houses. In this paper, an optimization-based approach is
proposed to determine the optimum PHEV parking capacities in
candidate nodes of the distribution system. In so doing, a profile for
charging and discharging of PHEVs is developed in order to flatten
the network load profile. Then, this profile is used in solving an
optimization problem to minimize the distribution system losses. The
outputs of the proposed method are the proper place for PHEV
parking lots and optimum capacity for each parking. The application
of the proposed method on the IEEE-34 node test feeder verifies the
effectiveness of the method.