Abstract: Propagation of arbitrary amplitude nonlinear Alfven
waves has been investigated in low but finite β electron-positron-ion
plasma including full ion dynamics. Using Sagdeev pseudopotential
method an energy integral equation has been derived. The Sagdeev
potential has been calculated for different plasma parameters and it
has been shown that inclusion of ion parallel motion along the
magnetic field changes the nature of slow shear Alfven wave solitons
from dip type to hump type. The effects of positron concentration,
plasma-β and obliqueness of the wave propagation on the solitary
wave structure have also been examined.
Abstract: The use of titanium fluoride and iron fluoride
(TiF3/FeF3) catalysts in combination with polutetrafluoroethylene
(PTFE) in plain zinc- dialkyldithiophosphate (ZDDP) oil is important
for the study of engine tribocomponents and is increasingly a strategy
to improve the formation of tribofilm and provide low friction and
excellent wear protection in reduced phosphorus plain ZDDP oil. The
influence of surface roughness and the concentration of
TiF3/FeF3/PTFE were investigated using bearing steel samples
dipped in lubricant solution at 100°C for two different heating time
durations. This paper addresses the effects of water drop contact
angle using different surface; finishes after treating them with
different lubricant combination. The calculated water drop contact
angles were analyzed using Design of Experiment software (DOE)
and it was determined that a 0.05 μm Ra surface roughness would
provide an excellent TiF3/FeF3/PTFE coating for antiwear resistance
as reflected in the Scanning electron microscopy (SEM) images and
the tribological testing under extreme pressure conditions. Both
friction and wear performance depend greatly on the PTFE/and
catalysts in plain ZDDP oil with 0.05 % phosphorous and on the
surface finish of bearing steel. The friction and wear reducing effects,
which was observed in the tribological tests, indicated a better micro
lubrication effect of the 0.05 μm Ra surface roughness treated at
100°C for 24 hours when compared to the 0.1 μm Ra surface
roughness with the same treatment.
Abstract: Background: Muscle Energy Techniques (MET) have
been widely used by manual therapists over the past years, but still
limited research validated its use and there was limited evidence to
substantiate the theories used to explain its effects. Objective: To
investigate the effect of Muscle Energy Technique (MET) on anterior
pelvic tilt in patients with lumbar spondylosis. Design: Randomized
controlled trial. Subjects: Thirty patients with anterior pelvic tilt from
both sexes were involved, aged between 35 to 50 years old and they
were divided into MET and control groups with 15 patients in each.
Methods: All patients received 3sessions/week for 4 weeks where the
study group received MET, Ultrasound and Infrared, and the control
group received U.S and I.R only. Pelvic angle was measured by
palpation meter, pain severity by the visual analogue scale and
functional disabilities by the Oswestry disability index. Results: Both
groups showed significant improvement in all measured variables.
The MET group was significantly better than the control group in
pelvic angle, pain severity, and functional disability as p-value were
(0.001, 0.0001, 0.0001) respectively. Conclusion and implication: the
study group fulfilled greater improvement in all measured variables
than the control group which implies that application of MET in
combination with U.S and I.R were more effective in improving
pelvic tilting angle, pain severity and functional disabilities than
using electrotherapy only.
Abstract: Singular value decomposition based optimisation of
geometric design parameters of a 5-speed gearbox is studied. During
the optimisation, a four-degree-of freedom torsional vibration model
of the pinion gear-wheel gear system is obtained and the minimum
singular value of the transfer matrix is considered as the objective
functions. The computational cost of the associated singular value
problems is quite low for the objective function, because it is only
necessary to compute the largest and smallest singular values (μmax
and μmin) that can be achieved by using selective eigenvalue solvers;
the other singular values are not needed. The design parameters are
optimised under several constraints that include bending stress,
contact stress and constant distance between gear centres. Thus, by
optimising the geometric parameters of the gearbox such as, the
module, number of teeth and face width it is possible to obtain a
light-weight-gearbox structure. It is concluded that the all optimised
geometric design parameters also satisfy all constraints.
Abstract: This study makes an integrated investigation on how
life satisfaction is associated with the Korean game users'
psychological variables (self-esteem, game and life self- efficacy),
social variables (bonding and bridging social capital), and
demographic variables (age, gender). The data used for the empirical
analysis came from a representative sample survey conducted in South
Korea. Results show that self-esteem and game efficacy were an
important antecedent to the degree of users’ life satisfaction. Both
bonding social capital and bridging social capital enhance the level of
the users’ life satisfaction. The importance of perspectives as well as
their implications for the game users and further associated research is
explored.
Abstract: A lower consumption of thermal energy will
contribute not only to a reduction in the running costs, but also in the
reduction of pollutant emissions that contribute to the greenhouse
effect. Cogeneration or CHP (Combined Heat and Power) is the
system that produces power and usable heat simultaneously by
decreasing the pollutant emissions and increasing the efficiency.
Combined production of mechanical or electrical and thermal energy
using a simple energy source, such as oil, coal, natural or liquefied
gas, biomass or the sun; affords remarkable energy savings and
frequently makes it possible to operate with greater efficiency when
compared to a system producing heat and power separately. This
study aims to bring out the contributions of cogeneration systems to
the environment and sustainability by saving the energy and reducing
the emissions. In this way we made a comprehensive investigation in
the literature by focusing on the environmental aspects of the
cogeneration systems. In the light of these studies we reached that,
cogeneration systems must be consider in sustainability and their
benefits on protecting the ecology must be investigated.
Abstract: Workflow scheduling is an important part of cloud
computing and based on different criteria it decides cost, execution
time, and performances. A cloud workflow system is a platform
service facilitating automation of distributed applications based on
new cloud infrastructure. An aspect which differentiates cloud
workflow system from others is market-oriented business model, an
innovation which challenges conventional workflow scheduling
strategies. Time and Cost optimization algorithm for scheduling
Hybrid Clouds (TCHC) algorithm decides which resource should be
chartered from public providers is combined with a new De-De
algorithm considering that every instance of single and multiple
workflows work without deadlocks. To offset this, two new concepts
- De-De Dodging Algorithm and Priority Based Decisive Algorithm -
combine with conventional deadlock avoidance issues by proposing
one algorithm that maximizes active (not just allocated) resource use
and reduces Makespan.
Abstract: A novel chromium-free protective coating films based
on a zeolite coating was growing onto a FeCrAlloy metal using in –
situ hydrothermal method. The zeolite film was obtained using in-situ
crystallization process that is capable of coating large surfaces with
complex shape and in confined spaces has been developed. The
zeolite coating offers an advantage of a high mechanical stability and
thermal stability. The physicochemical properties were investigated
using X-ray diffraction (XRD), Electron Microscopy (SEM), Energy
Dispersive X–ray Analysis (EDX) and Thermogravimetric Analysis
(TGA). The transition from oxide-on-alloy wires to hydrothermally
synthesised uniformly zeolite coated surfaces was followed using
SEM and XRD. In addition, the robustness of the prepared coating
was confirmed by subjecting these to thermal cycling (ambient to
550oC).
Abstract: Grains, including oats (Avena sativa L.), have been
recognized functional foods, because provide beneficial effect on the
health of the consumer and decrease the risk of various diseases. Oats
are good source of soluble fibre, essential amino acids, unsaturated
fatty acids, vitamins and minerals. Oat breeders have developed oat
varieties and improved yielding ability potential of oat varieties.
Therefore, the aim of investigation was to analyze the composition of
perspective oat varieties and breeding lines grains grown in different
conditions and evaluate functional properties. In the studied samples
content of protein, starch, β-glucans, total dietetic fibre, composition
of amino acids and vitamin E were determined. The results of
analysis showed that protein content depending of varieties ranged
9.70% to 17.30% total dietary fibre 13.66 g100g-1 to 30.17 g100g-1,
content of β-glucans 2.7 g100g-1 to 3.5 g100g-1, amount of
vitamin E (α-tocopherol) determined from 4 mgkg-1 to 9.9 mgkg-1.
The sums of essential amino acids in oat grain samples were
determined from 31.63 gkg-1 to 54.90 gkg-1. It is concluded that
amino acids composition of husked and naked oats grown in organic
or conventional conditions is close to optimal for human health.
Abstract: The aim of the present study is to investigate
consumers' determinants of intention toward the adoption of Smart
Grid solutions and technologies. Ajzen's Theory of Planned
Behaviour (TPB) model is applied and tested to explain the formation
of such adoption intention. An exogenous variable, taking into
account the resistance to change of individuals, was added to the
basic model. The elicitation study allowed obtaining salient modal
beliefs, which were used, with the support of literature, to design the
questionnaire. After the screening phase, data collected from the
main survey were analysed for evaluating measurement model's
reliability and validity. Consistent with the theory, the results of
structural equation analysis revealed that attitude, subjective norm,
and perceived behavioural control positively, which affected the
adoption intention. Specifically, the variable with the highest estimate
loading factor was found to be the perceived behavioural control,
and, the most important belief related to each construct was
determined (e.g., energy saving was observed to be the most
significant belief linked with attitude). Further investigation indicated
that the added exogenous variable has a negative influence on
intention; this finding confirmed partially the hypothesis, since this
influence was indirect: such relationship was mediated by attitude.
Implications and suggestions for future research are discussed.
Abstract: Chalcopyrite (CuFeS2) is the most common primary
mineral used for the commercial production of copper. The low
dissolution efficiency of chalcopyrite in sulfate media has prevented
an efficient industrial leaching of this mineral in sulfate media. Ferric
ions, bacteria, oxygen and other oxidants have been used as oxidizing
agents in the leaching of chalcopyrite in sulfate and chloride media
under atmospheric or pressure leaching conditions. Two leaching
methods were studied to evaluate chalcopyrite (CuFeS2) dissolution
in acid media. First, the conventional oxidative acid leaching method
was carried out using sulfuric acid (H2SO4) and potassium
dichromate (K2Cr2O7) as oxidant at atmospheric pressure. Second,
microwave-assisted acid leaching was performed using the
microwave accelerated reaction system (MARS) for same reaction
media. Parameters affecting the copper extraction such as leaching
time, leaching temperature, concentration of H2SO4 and
concentration of K2Cr2O7 were investigated. The results of
conventional acid leaching experiments were compared to the
microwave leaching method. It was found that the copper extraction
obtained under high temperature and high concentrations of oxidant
with microwave leaching is higher than those obtained
conventionally. 81% copper extraction was obtained by the
conventional oxidative acid leaching method in 180 min, with the
concentration of 0.3 mol/L K2Cr2O7 in 0.5M H2SO4 at 50 ºC, while
93.5% copper extraction was obtained in 60 min with microwave
leaching method under same conditions.
Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: The purpose of this study is to determine the
relationship of anxiety level between male and female undergraduates
at a private university in Malaysia. Convenient sampling method used
in this study in which the students were selected based on the
grouping assigned by the faculty. There were 214 undergraduates
who registered the probability courses had participated in this study.
Mathematics Anxiety Rating Scale (MARS) was the instrument used
in study which used to determine students’ anxiety level towards
probability. Reliability and validity of instrument was done before the
major study was conducted. In the major study, students were given
briefing about the study conducted. Participation of this study was
voluntary. Students were given consent form to determine whether
they agree to participate in the study. Duration of two weeks was
given for students to complete the given online questionnaire. The
data collected will be analyzed using Statistical Package for the
Social Sciences (SPSS) to determine the level of anxiety. There were
three anxiety level, i.e., low, average and high. Students’ anxiety
level was determined based on their scores obtained compared with
the mean and standard deviation. If the scores obtained were below
mean and standard deviation, the anxiety level was low. If the scores
were at below and above the mean and between one standard
deviation, the anxiety level was average. If the scores were above the
mean and greater than one standard deviation, the anxiety level was
high. Results showed that both of genders were having average
anxiety level. Among low, average and high anxiety level, frequency
of males were found to be higher as compared to females. Hence, the
mean values obtained for males (M = 3.62) was higher than females
(M = 3.42). In order to be significant of anxiety level among the
gender, the p-value should be less than .05. The p-value obtained in
this study was .117. However, this value was greater than .05. Thus,
there was no significant difference of anxiety level among the gender.
In other words, there was no relationship of anxiety level with the
gender.
Abstract: The design of Reverse logistics Network has attracted
growing attention with the stringent pressures from both
environmental awareness and business sustainability. Reverse
logistical activities include return, remanufacture, disassemble and
dispose of products can be quite complex to manage. In addition,
demand can be difficult to predict, and decision making is one of the
challenges task in such network. This complexity has amplified the
need to develop an integrated architecture for product return as an
enterprise system. The main purpose of this paper is to design Multi
Agent System (MAS) architecture using the Prometheus
methodology to efficiently manage reverse logistics processes. The
proposed MAS architecture includes five types of agents: Gate
keeping Agent, Collection Agent, Sorting Agent, Processing Agent
and Disposal Agent which act respectively during the five steps of
reverse logistics Network.
Abstract: This paper introduces a boost converter with a new
active snubber cell. In this circuit, all of the semiconductor
components in the converter softly turns on and turns off with the
help of the active snubber cell. Compared to the other converters, the
proposed converter has advantages of size, number of components
and cost. The main feature of proposed converter is that the extra
voltage stresses do not occur on the main switches and main diodes.
Also, the current stress on the main switch is acceptable level.
Moreover, the proposed converter can operates under light load
conditions and wide input line voltage. In this study, the operating
principle of the proposed converter is presented and its operation is
verified with the Proteus simulation software for a 1 kW and 100 kHz
model.
Abstract: Currently, green rating systems are mainly utilized for
correctly sizing mechanical and electrical systems, which have short
lifetime expectancies. In these systems, passive solar and bio-climatic
architecture, which have long lifetime expectancies, are neglected.
Urban rating systems consider buildings and services in addition to
neighborhoods and public transportation as integral parts of the built
environment. The main goal of this study was to develop a more
consistent point allocation system for urban building standards by
using six different lifetime shearing layers: Site, Structure, Skin,
Services, Space, and Stuff, each reflecting distinct environmental
damages. This shearing-layer concept was applied to internationally
well-known rating systems: Leadership in Energy and Environmental
Design (LEED) for Neighborhood Development, BRE
Environmental Assessment Method (BREEAM) for Communities
and Comprehensive Assessment System for Building Environmental
Efficiency (CASBEE) for Urban Development. The results showed
that LEED for Neighborhood Development and BREEAM for
Communities focused on long-lifetime-expectancy building designs,
whereas CASBEE for Urban Development gave equal importance to
the Building and Service Layers. Moreover, although this rating
system was applied using a building-scale assessment, “Urban Area +
Buildings” focuses on a short-lifetime-expectancy system design,
neglecting to improve the architectural design by considering bioclimatic
and passive solar aspects.
Abstract: This paper presents the local mesh co-occurrence
patterns (LMCoP) using HSV color space for image retrieval system.
HSV color space is used in this method to utilize color, intensity and
brightness of images. Local mesh patterns are applied to define the
local information of image and gray level co-occurrence is used to
obtain the co-occurrence of LMeP pixels. Local mesh co-occurrence
pattern extracts the local directional information from local mesh
pattern and converts it into a well-mannered feature vector using gray
level co-occurrence matrix. The proposed method is tested on three
different databases called MIT VisTex, Corel, and STex. Also, this
algorithm is compared with existing methods, and results in terms of
precision and recall are shown in this paper.
Abstract: In this paper, we provided a literature survey on the
artificial stock problem (ASM). The paper began by exploring the
complexity of the stock market and the needs for ASM. ASM
aims to investigate the link between individual behaviors (micro
level) and financial market dynamics (macro level). The variety of
patterns at the macro level is a function of the AFM complexity. The
financial market system is a complex system where the relationship
between the micro and macro level cannot be captured analytically.
Computational approaches, such as simulation, are expected to
comprehend this connection. Agent-based simulation is a simulation
technique commonly used to build AFMs. The paper proceeds by
discussing the components of the ASM. We consider the roles
of behavioral finance (BF) alongside the traditionally risk-averse
assumption in the construction of agent’s attributes. Also, the
influence of social networks in the developing of agents interactions is
addressed. Network topologies such as a small world, distance-based,
and scale-free networks may be utilized to outline economic
collaborations. In addition, the primary methods for developing
agents learning and adaptive abilities have been summarized.
These incorporated approach such as Genetic Algorithm, Genetic
Programming, Artificial neural network and Reinforcement Learning.
In addition, the most common statistical properties (the stylized facts)
of stock that are used for calibration and validation of ASM are
discussed. Besides, we have reviewed the major related previous
studies and categorize the utilized approaches as a part of these
studies. Finally, research directions and potential research questions
are argued. The research directions of ASM may focus on the macro
level by analyzing the market dynamic or on the micro level by
investigating the wealth distributions of the agents.
Abstract: Nowadays, several research studies point up that an
active lifestyle is essential for physical and mental health benefits.
Mobile phones have greatly influenced people’s habits and attitudes
also in the way they exercise. Our research work is mainly focused on
investigating how to exploit mobile technologies to favour people’s
exertion experience. To this end, we developed an exertion framework
users can exploit through a real world mobile application, called
EverywhereSport Run (EWRun), designed to act as a virtual personal
trainer to support runners during their trainings. In this work, inspired
by both previous findings in the field of interaction design for people
with visual impairments, feedback gathered from real users of our
framework, and positive results obtained from two experimentations,
we present some new interaction facilities we designed to enhance
the interaction experience during a training. The positive obtained
results helped us to derive some interaction design recommendations
we believe will be a valid support for designers of future mobile
systems conceived to be used in circumstances where there are limited
possibilities of interaction.
Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.