Abstract: Fresh concrete has one of dynamic properties known
as slump. Slump of concrete is design to compatible with placing
method. Due to hydration reaction of cement, the slump of concrete
is loss through time. Therefore, delayed concrete probably get reject
because slump is unacceptable. In order to recover the slump of
delayed concrete the second dose of superplasticizer (naphthalene
based type F) is added into the system, the slump recovery can be
done as long as the concrete is not setting. By adding superplasticizer
as solution for recover unusable slump loss concrete may affects
other concrete properties. Therefore, this paper was observed setting
times and compressive strength of concrete after being re-dose with
chemical admixture type F (superplasticizer, naphthalene based) for
slump recovery. The concrete used in this study was fly ash concrete
with fly ash replacement of 0%, 30% and 50% respectively. Concrete
mix designed for test specimen was prepared with paste content (ratio
of volume of cement to volume of void in the aggregate) of 1.2 and
1.3, water-to-binder ratio (w/b) range of 0.3 to 0.58, initial dose of
superplasticizer (SP) range from 0.5 to 1.6%. The setting times of
concrete were tested both before and after re-dosed with different
amount of second dose and time of dosing. The research was
concluded that addition of second dose of superplasticizer would
increase both initial and final setting times accordingly to dosage of
addition. As for fly ash concrete, the prolongation effect was higher
as the replacement of fly ash increase. The prolongation effect can
reach up to maximum about 4 hours. In case of compressive strength,
the re-dosed concrete has strength fluctuation within acceptable range
of ±10%.
Abstract: This paper describes the development of new class of
epoxy based rice husk filled jute reinforced composites. Rice husk
flour is added in 0%, 1%, 3%, 5% by weight. Epoxy resin and
triethylenetetramine (T.E.T.A) is used as matrix and hardener
respectively. It investigates the mechanical properties of the
composites and a comparison is done for monolithic jute composite
and the filled ones. The specimens are prepared according to the
ASTM standards and experimentation is carried out using INSTRON
8801. The result shows that with the increase of filler percentage the
tensile properties increases but compressive and flexural properties
decreases.
Abstract: Brushless DC motors (BLDC) are widely used in
industrial areas. The BLDC motors are driven either by indirect ACAC
converters or by direct AC-AC converters. Direct AC-AC
converters i.e. matrix converters are used in this paper to drive the
three phase BLDC motor and it eliminates the bulky DC link energy
storage element. A matrix converter converts the AC power supply to
an AC voltage of variable amplitude and variable frequency. A
control technique is designed to generate the switching pulses for the
three phase matrix converter. For the control of speed of the BLDC
motor a separate PI controller and Fuzzy Logic Controller (FLC) are
designed and a hysteresis current controller is also designed for the
control of motor torque. The control schemes are designed and tested
separately. The simulation results of both the schemes are compared
and contrasted in this paper. The results show that the fuzzy logic
control scheme outperforms the PI control scheme in terms of
dynamic performance of the BLDC motor. Simulation results are
validated with the experimental results.
Abstract: The question of legal liability over injury arising out
of the import and the introduction of GM food emerges as a crucial
issue confronting to promote GM food and its derivatives. There is a
greater possibility of commercialized GM food from the exporting
country to enter importing country where status of approval shall not
be same. This necessitates the importance of fixing a liability
mechanism to discuss the damage, if any, occurs at the level of
transboundary movement or at the market. There was a widespread consensus to develop the Cartagena
Protocol on Biosafety and to give for a dedicated regime on liability
and redress in the form of Nagoya Kuala Lumpur Supplementary
Protocol on the Liability and Redress (‘N-KL Protocol’) at the
international context. The national legal frameworks based on this
protocol are not adequately established in the prevailing food
legislations of the developing countries. The developing economy
like India is willing to import GM food and its derivatives after the
successful commercialization of Bt Cotton in 2002. As a party to the
N-KL Protocol, it is indispensable for India to formulate a legal
framework and to discuss safety, liability, and regulatory issues
surrounding GM foods in conformity to the provisions of the
Protocol. The liability mechanism is also important in the case where
the risk assessment and risk management is still in implementing
stage. Moreover, the country is facing GM infiltration issues with its
neighbors Bangladesh. As a precautionary approach, there is a need
to formulate rules and procedure of legal liability to discuss any kind
of damage occurs at transboundary trade. In this context, the
proposed work will attempt to analyze the liability regime in the
existing Food Safety and Standards Act, 2006 from the applicability
and domestic compliance and to suggest legal and policy options for
regulatory authorities.
Abstract: Average temperatures worldwide are expected to
continue to rise. At the same time, major cities in developing
countries are becoming increasingly populated and polluted.
Governments are tasked with the problem of overheating and air
quality in residential buildings. This paper presents the development
of a model, which is able to estimate the occupant exposure
to extreme temperatures and high air pollution within domestic
buildings. Building physics simulations were performed using the
EnergyPlus building physics software. An accurate metamodel is
then formed by randomly sampling building input parameters and
training on the outputs of EnergyPlus simulations. Metamodels are
used to vastly reduce the amount of computation time required when
performing optimisation and sensitivity analyses. Neural Networks
(NNs) have been compared to a Radial Basis Function (RBF)
algorithm when forming a metamodel. These techniques were
implemented using the PyBrain and scikit-learn python libraries,
respectively. NNs are shown to perform around 15% better than RBFs
when estimating overheating and air pollution metrics modelled by
EnergyPlus.
Abstract: The purposes of this study were to: 1) investigate
operation conditions of SME automotive part industry in Bangkok
and vicinity and 2) to compare operation problem levels of SME
automotive part industry in Bangkok and vicinity according to the
sizes of the enterprises. Samples in this study included 196
entrepreneurs of SME automotive part industry in Bangkok and
vicinity derived from simple random sampling and calculation from
R. V. Krejcie and D. W. Morgan’s tables. Research statistics included
frequency, percentage, mean, standard deviation, and T-test. The
results revealed that in general the problem levels of SME automotive
part industry in Bangkok and vicinity were high. When considering
in details, it was found that the problem levels were high at every
aspect, i.e. personal, production, export, finance, and marketing
respectively. The comparison of the problem levels according to the
sizes of the enterprises revealed statistically significant differences at
.05. When considering on each aspect, it was found that the aspect
with the statistical difference at .05 included 5 aspects, i.e.
production, marketing, finance, personal, and export. The findings
also showed that small enterprises faced more severe problems than
those of medium enterprises.
Abstract: The increase in electric power demand in face of
environmental issues has intensified the participation of renewable
energy sources such as photovoltaics, in the energy matrix of various
countries. Due to their operational characteristics, they can generate
time-varying harmonic and inter-harmonic distortions. For this
reason, the application of methods of measurement based on
traditional Fourier analysis, as proposed by IEC 61000-4-7, can
provide inaccurate results. Considering the aspects mentioned herein,
came the idea of the development of this work which aims to present
the results of a comparative evaluation between a methodology
arising from the combination of the Prony method with the Kalman
filter and another method based on the IEC 61000-4-30 and IEC
61000-4-7 standards. Employed in this study were synthetic signals
and data acquired through measurements in a 50kWp photovoltaic
installation.
Abstract: Value addition to agricultural produce is of possible
potential in reducing poverty, improving food security and
malnutrition, therefore the need to develop small and microenterprises
of sweet potato production. A study was carried out in Nigeria to determine the acceptability
of blends sweet potato (Ipomea batatas) and commodities yellow
maize (Zea mays), millet (Pennisetum glaucum), soybean (Glycine
max), bambara groundnut (Vigna subterranean), guinea corn
(Sorghum vulgare), wheat (Triticum aestivum), and roselle (Hibiscus
sabdariffa) through sensory evaluation. Sweet potato (Ipomea batatas) roots were processed using two
methods: oven and sun drying. The blends were also assessed in
terms of functional, chemical and color properties. Most acceptable blends include BAW (80:20 of sweet
potato/wheat), BBC (80:20 of sweet potato/guinea corn), AAB (60:40
of sweet potato/guinea corn), YTE (100% soybean), TYG (100%
sweet potato), KTN (100% wheat flour), XGP (80:20 of sweet
potato/soybean), XAX (60:40 of sweet potato/wheat), LSS (100%
Roselle), CHK (100% Guinea corn), and ABC (60:40% of sweet
potato/ yellow maize). In addition, carried out chemical analysis
revealed that sweet potato has high percentage of vitamins A and C,
potassium (K), manganese (Mn), calcium (Ca), magnesium (Mg) and
iron (Fe) and fibre content. There is also an increase of vitamin A and
Iron in the blended products.
Abstract: The quality of concrete is usually defined by compressive strength, but flexural strength is the most important characteristic of concrete in a pavement which control the mix design of concrete instead of compressive strength. Therefore, the aggregates which are selected for the pavements are affected by higher flexural strength. Roller Compacting Concrete Pavement (RCCP) is not a new construction method. The other characteristic of this method is no bleeding and less shrinkage due to the lower amount of water. For this purpose, a roller is needed for placing and compacting. The surface of RCCP is not smooth; therefore, the most common use of this pavement is in an industrial zone with slower traffic speed which requires durable and tough pavement. For preparing a smoother surface, it can be achieved by asphalt paver. RCCP decrease the finishing cost because there are no bars, formwork, and the lesser labor need for placing the concrete. In this paper, different aspect of RCCP such as mix design, flexural, compressive strength and focus on the different part of RCCP on detail have been investigated.
Abstract: Social networking sites such as Twitter and Facebook
attracts over 500 million users across the world, for those users, their
social life, even their practical life, has become interrelated. Their
interaction with social networking has affected their life forever.
Accordingly, social networking sites have become among the main
channels that are responsible for vast dissemination of different kinds
of information during real time events. This popularity in Social
networking has led to different problems including the possibility of
exposing incorrect information to their users through fake accounts
which results to the spread of malicious content during life events.
This situation can result to a huge damage in the real world to the
society in general including citizens, business entities, and others. In this paper, we present a classification method for detecting the
fake accounts on Twitter. The study determines the minimized set of
the main factors that influence the detection of the fake accounts on
Twitter, and then the determined factors are applied using different
classification techniques. A comparison of the results of these
techniques has been performed and the most accurate algorithm is
selected according to the accuracy of the results. The study has been
compared with different recent researches in the same area; this
comparison has proved the accuracy of the proposed study. We claim
that this study can be continuously applied on Twitter social network
to automatically detect the fake accounts; moreover, the study can be
applied on different social network sites such as Facebook with minor
changes according to the nature of the social network which are
discussed in this paper.
Abstract: Highly stable and homogeneously dispersed amino
acid coated silver nanoparticles (ANP) of ≈ 10 nm diameter, ranging
from 420 to 430 nm are prepared on AgNO3 solution addition to gum
of Azadirachta indica solution at 373.15 K. The amino acids were
selected based on their polarity. The synthesized nanoparticles were
characterized by UV-Vis, FTIR spectroscopy, HR-TEM, XRD, SEM
and 1H-NMR. The coated nanoparticles were used as catalyst for the
reduction of methylene blue dye in presence of Sn(II) in aqueous,
anionic and cationic micellar media. The rate of reduction of dye was
determined by measuring the absorbance at 660 nm,
spectrophotometrically and followed the order: Kcationic > Kanionic >
Kwater. After 12 min and in absence of the ANP, only 2%, 3% and 6%
of the dye reduction was completed in aqueous, anionic and cationic
micellar media respectively while, in presence of ANP coated by
polar neutral amino acid with non-polar -R group, the reduction
completed to 84%, 95% and 98% respectively. The ANP coated with
polar neutral amino acid having non-polar -R group, increased the
rate of reduction of the dye by 94, 3205 and 6370 folds in aqueous,
anionic and cationic micellar media respectively. Also, the rate of
reduction of the dye increased by three folds when the micellar media
was changed from anionic to cationic when the ANP is coated by a
polar neutral amino acid having a non-polar -R group.
Abstract: Carbon dioxide is one of the major greenhouse gas
(GHG) contributors. It is an obligation of the industry to reduce the
amount of carbon dioxide emission to the acceptable limits.
Tremendous research and studies are reported in the past and still the
quest to find the suitable and economical solution of this problem
needed to be explored in order to develop the most plausible absorber
for carbon dioxide removal. Amino acids can be potential alternate
solvents for carbon dioxide capture from gaseous streams. This is due
to its ability to resist oxidative degradation, low volatility and its
ionic structure. In addition, the introduction of promoter-like
piperazine to amino acid helps to further enhance the solubility. In
this work, the effect of piperazine on thermo physical properties and
solubility of β-Alanine aqueous solutions were studied for various
concentrations. The measured physicochemical properties data was
correlated as a function of temperature using least-squares method
and the correlation parameters are reported together with it respective
standard deviations. The effect of activator piperazine on the CO2
loading performance of selected amino acid under high-pressure
conditions (1bar to 10bar) at temperature range of (30 to 60)oC was
also studied. Solubility of CO2 decreases with increasing temperature
and increases with increasing pressure. Quadratic representation of
solubility using Response Surface Methodology (RSM) shows that
the most important parameter to optimize solubility is system
pressure. The addition of promoter increases the solubility effect of
the solvent.
Abstract: A broadband wire monopole antenna loaded by inhomogeneous stack of annular dielectric ring resonators (DRRs) is proposed. The proposed antenna exhibits a broad impedance bandwidth from 3 to 30 GHz. This is achieved by adding an external step matching network at the antenna feed point. The matching network is comprised of three annular DRRs possessing different permittivity values and sharing the same axial over a finite ground plane. The antenna performance is characterized using full-wave EM simulation. Compared to previous-reported wire antennas with improved bandwidth achieved by DRRs, the proposed topology provides relatively compact realization and superior broadband performance.
Abstract: Dengue is a mosquito-borne viral disease endemic in
many countries in the tropics and sub-tropics. The state of Punjab in
India shows cyclical and seasonal variation in dengue cases. The
Case Fatality Rate of Dengue has ranged from 0.6 to 1.0 in the past
years. The department has initiated review of the cases that have died
due to dengue in order to know the exact cause of the death in a case
of dengue. The study has been undertaken to know the other
associated co-morbidities and factors causing death in a case of
dengue. The study used the predesigned proforma on which the
records (medical and Lab) were recorded and reviewed by the expert
committee of the doctors. This study has revealed that cases of
dengue having co-morbidities have longer stay in hospital. Fluid
overload and co-morbidities have been found as major factors leading
to death, however, in a confirmed case of dengue hepatorenal
shutdown was found to be major cause of mortality. The data
obtained will help in sensitizing the treating physicians in order to
decrease the mortality due to dengue in future.
Abstract: This paper focuses on the mathematical modeling for
solidification of Al alloy in a cube mold cavity to study the
solidification behavior of casting process. The parametric
investigation of solidification process inside the cavity was
performed by using computational solidification/melting model
coupled with Volume of fluid (VOF) model. The implicit filling
algorithm is used in this study to understand the overall process from
the filling stage to solidification in a model metal casting process.
The model is validated with past studied at same conditions. The
solidification process is analyzed by including the effect of pouring
velocity as well as natural convection from the wall and geometry of
the cavity. These studies show the possibility of various defects
during solidification process.
Abstract: A myriad of environmental issues face the Nigerian
industrial region, resulting from; oil and gas production, mining,
manufacturing and domestic wastes. Amidst these, much effort has
been directed by stakeholders in the Nigerian oil producing regions,
because of the impacts of the region on the wider Nigerian economy.
Although collaborative environmental management has been noted as
an effective approach in managing environmental issues, little
attention has been given to the roles and practices of stakeholders in
effecting a collaborative environmental management framework for
the Nigerian oil-producing region. This paper produces a framework
to expand and deepen knowledge relating to stakeholders aspects of
collaborative roles in managing environmental issues in the Nigeria
oil-producing region. The knowledge is derived from analysis of
stakeholders’ practices – studied through multiple case studies using
document analysis. Selected documents of key stakeholders –
Nigerian government agencies, multi-national oil companies and host
communities, were analyzed. Open and selective coding was
employed manually during document analysis of data collected from
the offices and websites of the stakeholders. The findings showed
that the stakeholders have a range of roles, practices, interests, drivers
and barriers regarding their collaborative roles in managing
environmental issues. While they have interests for efficient resource
use, compliance to standards, sharing of responsibilities, generating
of new solutions, and shared objectives; there is evidence of major
barriers and these include resource allocation, disjointed policy,
ineffective monitoring, diverse socio- economic interests, lack of
stakeholders’ commitment and limited knowledge sharing. However,
host communities hold deep concerns over the collaborative roles of
stakeholders for economic interests, particularly, where government
agencies and multi-national oil companies are involved. With these
barriers and concerns, a genuine stakeholders’ collaboration is found
to be limited, and as a result, optimal environmental management
practices and policies have not been successfully implemented in the
Nigeria oil-producing region. A framework is produced that describes
practices that characterize collaborative environmental management
might be employed to satisfy the stakeholders’ interests. The
framework recommends critical factors, based on the findings, which
may guide a collaborative environmental management in the oil
producing regions. The recommendations are designed to re-define
the practices of stakeholders in managing environmental issues in the
oil producing regions, not as something wholly new, but as an
approach essential for implementing a sustainable environmental
policy. This research outcome may clarify areas for future research as
well as to contribute to industry guidance in the area of collaborative
environmental management.
Abstract: The change in orbit evolution between collocated
satellites (X, Y) inside +/-0.09° E/W and +/- 0.07° N/S cluster, after
one of these satellites is placed in an inclined orbit (satellite X) and
the effect of this change in the collocation safety inside the cluster
window has been studied and evaluated. Several collocation scenarios had been studied in order to adjust
the location of both satellites inside their cluster to maximize the
separation between them and safe the mission.
Abstract: Customer’ needs, quality, and value creation while
reducing costs through supply chain management provides challenges
and opportunities for companies and researchers. In the light of these
challenges, modern ideas must contribute to counter these challenges
and exploit opportunities. Therefore, this paper discusses the impact
of the quality cost on revenue sharing as a most important incentive
to configure business networks. This paper develops the quality cost approach to align with the
modern era. It develops a model to measure quality costs which
might enable firms to manage revenue sharing in a supply chain. The
developed model includes five categories; besides the well-known
four categories (namely prevention costs, appraisal costs, internal
failure costs, and external failure costs), a new category has been
developed in this research as a new vision of the relationship between
quality costs and innovations in industry. This new category is
Recycle Cost. This paper also examines whether such quality costs in
supply chains influence the revenue sharing between partners. Using the author's quality cost model, the relationship between
quality costs and revenue sharing among partners is examined using a
case study in an Egyptian manufacturing company which is a part of
a supply chain. This paper argues that the revenue-sharing proportion
allocated to supplier increases as the recycle cost of supplier
increases, and the revenue-sharing proportion allocated to
manufacturer increases as the prevention and appraisal costs increase,
as well as the failure costs, the recycle costs of manufacturer, and the
recycle costs of suppliers decrease. However, the results present
surprising findings. The purposes of this study are developing quality cost approach
and understanding the relationships between quality costs and
revenue sharing in supply chains. Therefore, the present study
contributes to theory and practice by explaining how the cost of
recycling can be combined in quality cost model to better
understanding the revenue sharing among partners in supply chains.
Abstract: This paper presents numerical analysis in terms of
buckling resistance of GFRP sandwich infill panels system under the
influence of increased temperature on the foam core. Failure mode
under in-plane compression is studied by means of numerical analysis
with ABAQUS platform. Parameters considered in this study are
contact length and both the type of foam for core and the variation of
its module elastic under the thermal influence. Increment of
temperature is considered in static cases and only applied to core.
Indeed, it is proven that the effect of temperature alters the mechanical
properties of the entire panel system. Moreover, the rises of
temperature result in a decrease in strength of the panel. This is due to
the polymeric nature of this material. Additionally, the contact length
also displays the effect on performance of infill panel. Their
significance factors are based on type of polymer for core. Therefore,
by comparing difference type of core material, the variation can be
reducing.
Abstract: Recently, Job Recommender Systems have gained
much attention in industries since they solve the problem of
information overload on the recruiting website. Therefore, we
proposed Extended Personalized Job System that has the capability of
providing the appropriate jobs for job seeker and recommending
some suitable information for them using Data Mining Techniques
and Dynamic User Profile. On the other hands, company can also
interact to the system for publishing and updating job information.
This system have emerged and supported various platforms such as
web application and android mobile application. In this paper, User
profiles, Implicit User Action, User Feedback, and Clustering
Techniques in WEKA libraries were applied and implemented. In
additions, open source tools like Yii Web Application Framework,
Bootstrap Front End Framework and Android Mobile Technology
were also applied.