Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: Within Rapid Prototyping technologies are used many
types of materials. Many of them are recyclable but there are still as
plastic like, so practically they do not degrade in the landfill.
Polylactic acid (PLA) is one of the special plastic materials, which
are biodegradable and available for 3D printing within Fused
Deposition Modeling (FDM) technology. The question is, if the
mechanical properties of produced models are comparable to similar
technical plastic materials which are usual for prototype production.
Presented paper shows the experiments results for tensile strength
measurements for specimens prepared with different 3D printer
settings and model orientation. Paper contains also the comparison of
tensile strength values with values measured on specimens produced
by conventional technologies as injection moulding.
Abstract: According to IR, 13C and 1H NMR, APT, 1D NOE,
2D heteronuclear 1H/13C HSQC and 2D DOSY experiments the main
chemical constituent of high-molecular preparations from Symphytum
asperum, S. caucasicum, S. officinale and Anchusa italica
(Boraginaceae) was found to be caffeic acid-derived polyether,
namely poly[3-(3,4-dihydroxyphenyl)glyceric acid] (PDPGA) or
poly[oxy-1-carboxy-2-(3,4-dihydroxyphenyl)ethylene]. Most
carboxylic groups of this polymer of A. italica are methylated.
Abstract: Chatter vibrations, occurring during cutting process,
cause vibration between the cutting tool and workpiece, which
deteriorates surface roughness and reduces tool life. The purpose of
this study is to investigate the influence of cutting parameters and
tool construction on surface roughness and vibration in turning of
aluminum alloy AA2024. A new design of cutting tool is proposed,
which is filled up with epoxy granite in order to improve damping
capacity of the tool. Experiments were performed at the lathe using
carbide cutting insert coated with TiC and two different cutting tools
made of AISI 5140 steel. Taguchi L9 orthogonal array was applied to
design of experiment and to optimize cutting conditions. By the help
of signal-to-noise ratio and analysis of variance the optimal cutting
condition and the effect of the cutting parameters on surface
roughness and vibration were determined. Effectiveness of Taguchi
method was verified by confirmation test. It was revealed that new
cutting tool with epoxy granite has reduced vibration and surface
roughness due to high damping properties of epoxy granite in
toolholder.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: Internal circulation two-platen clamping system for
injection molding machine (IMM) has many potential advantages on
energy-saving. In order to estimate its properties, experiments were
carried out in this paper. Displacement and pressure of the components
were measured. In comparison, the model of hydraulic clamping
system was established by using AMESim. The related parameters as
well as the energy consumption could be calculated. According to the
analysis, the hydraulic system was optimized in order to reduce the
energy consumption.
Abstract: The UK is leading in online retail and mobile
adoption. However, there is a dearth of information relating to mobile
apparel retail, and developing an understanding about consumer
browsing and purchase behaviour in m-retail channel would provide
apparel marketers, mobile website and app developers with the
necessary understanding of consumers’ needs. Despite the rapid
growth of mobile retail businesses, no published study has examined
shopping behaviour on fashion mobile apps and websites. A mixed method approach helped to understand why fashion
consumers prefer websites on smartphones, when diverse mobile
apps are also available. The following research methods were
employed: survey, eye-tracking experiments, observation, and
interview with retrospective think aloud. The mobile gaze tracking
device by SensoMotoric Instruments was used to understand
frustrations in navigation and other issues facing consumers in
mobile channel. This method helped to validate and compliment
other traditional user-testing approaches in order to optimize user
experience and enhance the development of mobile retail channel.
The study involved eight participants - females aged 18 to 35 years
old, who are existing mobile shoppers. The participants used the
Topshop mobile app and website on a smart phone to complete a task
according to a specified scenario leading to a purchase. The
comparative study was based on: duration and time spent at different
stages of the shopping journey, number of steps involved and product
pages visited, search approaches used, layout and visual clues, as
well as consumer perceptions and expectations. The results from the data analysis show significant differences in
consumer behaviour when using a mobile app or website on a smart
phone. Moreover, two types of problems were identified, namely
technical issues and human errors. Having a mobile app does not
guarantee success in satisfying mobile fashion consumers. The
differences in the layout and visual clues seem to influence the
overall shopping experience on a smart phone. The layout of search
results on the website was different from the mobile app. Therefore,
participants, in most cases, behaved differently on different
platforms. The number of product pages visited on the mobile app
was triple the number visited on the website due to a limited visibility
of products in the search results. Although, the data on traffic trends
held by retailers to date, including retail sector breakdowns for visits
and views, data on device splits and duration, might seem a valuable
source of information, it cannot explain why consumers visit many
product pages, stay longer on the website or mobile app, or abandon
the basket. A comprehensive list of pros and cons was developed by
highlighting issues for website and mobile app, and recommendations
provided. The findings suggest that fashion retailers need to be aware of
actual consumers’ behaviour on the mobile channel and their expectations in order to offer a seamless shopping experience. Added
to which is the challenge of retaining existing and acquiring new
customers. There seem to be differences in the way fashion
consumers search and shop on mobile, which need to be explored in
further studies.
Abstract: Spectrum handover is a significant topic in the
cognitive radio networks to assure an efficient data transmission in
the cognitive radio user’s communications. This paper proposes a
comparison between three spectrum handover models: VIKOR, SAW
and MEW. Four evaluation metrics are used. These metrics are,
accumulative average of failed handover, accumulative average of
handover performed, accumulative average of transmission
bandwidth and, accumulative average of the transmission delay. As a difference with related work, the performance of the three
spectrum handover models was validated with captured data of
spectrum occupancy in experiments performed at the GSM frequency
band (824 MHz - 849 MHz). These data represent the actual behavior
of the licensed users for this wireless frequency band. The results of the comparison show that VIKOR Algorithm
provides a 15.8% performance improvement compared to SAW
Algorithm and, it is 12.1% better than the MEW Algorithm.
Abstract: This paper integrates Octagon and Square Search
pattern (OCTSS) motion estimation algorithm into H.264/AVC
(Advanced Video Coding) video codec in Adaptive Group of Pictures
(AGOP) mode. AGOP structure is computed based on scene change
in the video sequence. Octagon and square search pattern block-based
motion estimation method is implemented in inter-prediction process
of H.264/AVC. Both these methods reduce bit rate and computational
complexity while maintaining the quality of the video sequence
respectively. Experiments are conducted for different types of video
sequence. The results substantially proved that the bit rate,
computation time and PSNR gain achieved by the proposed method
is better than the existing H.264/AVC with fixed GOP and AGOP.
With a marginal gain in quality of 0.28dB and average gain in bitrate
of 132.87kbps, the proposed method reduces the average computation
time by 27.31 minutes when compared to the existing state-of-art
H.264/AVC video codec.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: This study presents a kinematic positioning approach
that uses a global positioning system (GPS) buoy for precise ocean
surface monitoring. The GPS buoy data from the two experiments are
processed using an accurate, medium-range differential kinematic
technique. In each case, the data from a nearby coastal site are
collected at a high rate (1 Hz) for more than 24 hours, and
measurements are conducted in neighboring tidal stations to verify
the estimated sea surface heights. The GPS buoy kinematic
coordinates are estimated using epoch-wise pre-elimination and a
backward substitution algorithm. Test results show that centimeterlevel
accuracy can be successfully achieved in determining sea
surface height using the proposed technique. The centimeter-level
agreement between the two methods also suggests the possibility of
using this inexpensive and more flexible GPS buoy equipment to
enhance (or even replace) current tidal gauge stations.
Abstract: The high-molecular water-soluble preparations from
several species of two genera (Symphytum and Anchusa) of
Boraginaceae family Symphytum asperum, S. caucasicum, S.officinale
and Anchusa italica were isolated. According to IR, 13C and 1H
NMR, APT, 1D NOE, 2D heteronuclear 1H/13C HSQC and 2D
DOSY experiments, the main chemical constituent of these
preparations was found to be caffeic acid-derived polyether, namely
poly[3-(3,4-dihydroxyphenyl)glyceric acid] (PDPGA) or poly[oxy-1-
carboxy-2-(3,4-dihydroxyphenyl)ethylene]. Most carboxylic groups
of this caffeic acid-derived polymer of A. italica are methylated.
Abstract: In this paper, we present a comparative study of three
methods of 2D face recognition system such as: Iso-Geodesic Curves
(IGC), Geodesic Distance (GD) and Geodesic-Intensity Histogram
(GIH). These approaches are based on computing of geodesic
distance between points of facial surface and between facial curves.
In this study we represented the image at gray level as a 2D surface in
a 3D space, with the third coordinate proportional to the intensity
values of pixels. In the classifying step, we use: Neural Networks
(NN), K-Nearest Neighbor (KNN) and Support Vector Machines
(SVM). The images used in our experiments are from two wellknown
databases of face images ORL and YaleB. ORL data base was
used to evaluate the performance of methods under conditions where
the pose and sample size are varied, and the database YaleB was used
to examine the performance of the systems when the facial
expressions and lighting are varied.
Abstract: Target of this study was the analysis of the impact of
crude glycerol on canine spermatozoa motility, morphology,
viability, and membrane integrity. Experiments were realized in vitro.
In the study, semen from 5 large dog breeds was used. They were
typical representatives of large breeds, coming from healthy rearing,
regularly vaccinated and integrated to the further breeding. Semen
collections were realized at the owners of animals and in the
veterinary clinic. Subsequently the experiments were realized at the
Department of Animal Physiology of the SUA in Nitra. The
spermatozoa motility was evaluated using CASA analyzer
(SpermVisionTM, Minitub, Germany) at the temperature 5 and 37°C
for 5 hours. In the study, 13 motility parameters were evaluated.
Generally, crude glycerol has generally negative effect on
spermatozoa motility. Morphological analysis was realized using
Hancock staining and the preparations were evaluated at
magnification 1000x using classification tables of morphologically
changed spermatozoa. Data clearly detected the highest number of
morphologically changed spermatozoa in the experimental groups
(know twisted tails, tail torso and tail coiling). For acrosome
alterations swelled acrosomes, removed acrosomes and acrosomes
with undulated membrane were detected. In this study also the effect
of crude glycerol on spermatozoa membrane integrity were analyzed.
The highest crude glycerol concentration significantly affects
spermatozoa integrity. Results of this study show that crude glycerol
has effect of spermatozoa motility, viability, and membrane integrity.
Detected changes are related to crude glycerol concentration,
temperature, as well as time of incubation.
Abstract: Wire Electric Discharge Machining (WEDM) is
thermal machining process capable of machining very hard
electrically conductive material irrespective of their hardness.
WEDM is being widely used to machine micro scale parts with the
high dimensional accuracy and surface finish. The objective of this
paper is to optimize the process parameters of wire EDM to fabricate
the micro channels and to calculate the surface finish and material
removal rate of micro channels fabricated using wire EDM. The
material used is aluminum 6061 alloy. The experiments were
performed using CNC wire cut electric discharge machine. The effect
of various parameters of WEDM like pulse on time (TON) with the
levels (100, 150, 200), pulse off time (TOFF) with the levels (25, 35,
45) and current (IP) with the levels (105, 110, 115) were investigated
to study the effect on output parameter i.e. Surface Roughness and
Material Removal Rate (MRR). Each experiment was conducted
under different conditions of pulse on time, pulse off time and peak
current. For material removal rate, TON and Ip
were the most significant process parameter. MRR increases with the increase in
TON and Ip and decreases with the increase in TOFF. For surface
roughness, TON and Ip have the maximum effect and TOFF was found
out to be less effective.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: The current study aims to highlight the loading
characteristics impact on the time evolution (focusing particularly on
long term effects) of the deformation of realized reinforced concrete
beams. Namely the tension stiffening code provisions (i.e. within
Eurocode 2) are reviewed with a clear intention to reassess their
operational value and predicting capacity. In what follows the
experimental programme adopted along with some preliminary
findings and numerical modeling attempts are presented. For a range of long slender reinforced concrete simply supported
beams (4200 mm) constant static sustained and repeated cyclic
loadings were applied mapping the time evolution of deformation.
All experiments were carried out at the Heavy Structures Lab of the
University of Leeds. During tests the mid-span deflection, creep
coefficient and shrinkage strains were monitored for duration of 90
days. The obtained results are set against the values predicted by
Eurocode 2 and the tools within an FE commercial package (i.e.
Midas FEA) to yield that existing knowledge and practise is at times
over-conservative.
Abstract: Ultraviolet photocatalytic oxidation (UV-PCO)
technology has been recommended as a green approach to health
indoor environment when it is integrated into mechanical ventilation
systems for inorganic and organic compounds removal as well as
energy saving due to less outdoor air intakes. Although much research
has been devoted to UV-PCO, limited information is available on the
UV-PCO behavior tested by the mixtures in literature. This project
investigated UV-PCO performance and by-product generation using a
single and a mixture of acetone and MEK at 100 ppb each in a
single-pass duct system in an effort to obtain knowledge associated
with competitive photochemical reactions involved in. The
experiments were performed at 20 % RH, 22 °C, and a gas flow rate of
128 m3/h (75 cfm). Results show that acetone and MEK mutually
reduced each other’s PCO removal efficiency, particularly negative
removal efficiency for acetone. These findings were different from
previous observation of facilitatory effects on the adsorption of
acetone and MEK on photocatalyst surfaces.
Abstract: When high strength reinforced concrete is exposed to
high temperature due to a fire, deteriorations occur such as loss in
strength and elastic modulus, cracking and spalling of the concrete.
Therefore, it is important to understand risk of structural safety in
building structures by studying structural behaviors and rehabilitation
of fire damaged high strength concrete structures. This paper aims at
investigating rehabilitation effect on fire damaged high strength
concrete beams using experimental and analytical methods. In the
experiments, flexural specimens with high strength concrete are
exposed to high temperatures according to ISO 834 standard time
temperature curve. From four-point loading test, results show that
maximum loads of the rehabilitated beams are similar to or higher than
those of the non-fire damaged RC beam. In addition, structural
analyses are performed using ABAQUS 6.10-3 with same conditions
as experiments to provide accurate predictions on structural and
mechanical behaviors of rehabilitated RC beams. The parameters are
the fire cover thickness and strengths of repairing mortar. Analytical
results show good rehabilitation effects, when the results predicted
from the rehabilitated models are compared to structural behaviors of
the non-damaged RC beams. In this study, fire damaged high strength concrete beams are
rehabilitated using polymeric cement mortar. The predictions from the
finite element (FE) models show good agreements with the
experimental results and the modeling approaches can be used to
investigate applicability of various rehabilitation methods for further
study.
Abstract: Present study was aimed to develop a discharge
measuring device for irrigation and laboratory channels. Experiments
were conducted on sharp edged constricted flow meters having four
types of width constrictions namely 2:1, 1.5:1, 1:1 and 90o in the
direction of flow. These devices were made of MS sheets and
installed separately in a rectangular flume. All these four devices
were tested under free and submerged flow conditions. Eight
different discharges varying from 2 lit/sec to 30 lit/sec were passed
through each device. In total around 500 observations of upstream
and downstream depths were taken in the present work. For each
discharge, free submerged and critical submergence under different
flow conditions were noted and plotted. Once the upstream and
downstream depths of flow over any of the device are known, the
discharge can be easily calculated with the help of the curves
developed for free and submerged flow conditions. The device
having contraction 2:1 is the most efficient one as it allows maximum
critical submergence.