Abstract: An envelope echo signal measurement is proposed in
this paper using echo signal observation from the 200 kHz echo
sounder receiver. The envelope signal without any object is compared
with the envelope signal of the sphere. Two diameter size steel ball
(3.1 cm & 2.2 cm) and two diameter size air filled stainless steel ball
(4.8 cm & 7.4 cm) used in this experiment. The target was positioned
about 0.5 m and 1.0 meter from the transducer face using nylon rope.
From the echo observation in time domain, it is obviously shown that
echo signal structure is different between the size, distance and type
of metal sphere. The amplitude envelope voltage for the bigger
sphere is higher compare to the small sphere and it confirm that the
bigger sphere have higher target strength compare to the small
sphere. Although the structure signal without any object are different
compare to the signal from the sphere, the reflected signal from the
tank floor increase linearly with the sphere size. We considered this
event happened because of the object position approximately to the
tank floor.
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: The charge-exchange xenon (CEX) ion generated by ion thruster can backflow to the surface of spacecraft and threaten to the safety of spacecraft operation. In order to evaluate the effects of the induced plasma environment in backflow regions on the spacecraft, we designed a spherical single Langmuir probe of 5.8cm in diameter for measuring low-density plasma parameters in backflow region of ion thruster. In practice, the tests are performed in a two-dimensional array (40cm×60cm) composed of 20 sites. The experiment results illustrate that the electron temperature ranges from 3.71eV to 3.96eV, with the mean value of 3.82eV and the standard deviation of 0.064eV. The electron density ranges from 8.30×1012/m3 to 1.66×1013/m3, with the mean value of 1.30×1013/m3 and the standard deviation of 2.15×1012/m3. All data is analyzed according to the “ideal" plasma conditions of Maxwellian distributions.
Abstract: This paper concerns about the experimental and
numerical investigations of energy absorption and axial tearing
behaviour of aluminium 6060 circular thin walled tubes under static
axial compression. The tubes are received in T66 heat treatment
condition with fixed outer diameter of 42mm, thickness of 1.5mm
and length of 120mm. The primary variables are the conical die
angles (15°, 20° and 25°). Numerical simulations are carried on
ANSYS/LS-DYNA software tool, for investigating the effect of
friction between the tube and the die.
Abstract: A dent is a gross distortion of the pipe cross-section.
Dent depth is defined as the maximum reduction in the diameter of
the pipe compared to the original diameter. Pipeline dent finite
element (FE) simulation and theoretical analysis are conducted in this
paper to develop an understanding of the geometric characteristics
and strain distribution in the pressurized dented pipe. Based on the
results, the magnitude of the denting force increases significantly
with increasing the internal pressure, and the maximum
circumferential and longitudinal strains increase by increasing the
internal pressure and the dent depth. The results can be used for
characterizing dents and ranking their risks to the integrity of a
pipeline.
Abstract: Fischer-Tropsch synthesis is one of the most
important catalytic reactions that convert the synthetic gas to light
and heavy hydrocarbons. One of the main issues is selecting the type
of reactor. The slurry bubble reactor is suitable choice for Fischer-
Tropsch synthesis because of its good qualification to transfer heat
and mass, high durability of catalyst, low cost maintenance and
repair. The more common catalysts for Fischer-Tropsch synthesis are
Iron-based and Cobalt-based catalysts, the advantage of these
catalysts on each other depends on which type of hydrocarbons we
desire to produce. In this study, Fischer-Tropsch synthesis is modeled
with Iron and Cobalt catalysts in a slurry bubble reactor considering
mass and momentum balance and the hydrodynamic relations effect
on the reactor behavior. Profiles of reactant conversion and reactant
concentration in gas and liquid phases were determined as the
functions of residence time in the reactor. The effects of temperature,
pressure, liquid velocity, reactor diameter, catalyst diameter, gasliquid
and liquid-solid mass transfer coefficients and kinetic
coefficients on the reactant conversion have been studied. With 5%
increase of liquid velocity (with Iron catalyst), H2 conversions
increase about 6% and CO conversion increase about 4%, With 8%
increase of liquid velocity (with Cobalt catalyst), H2 conversions
increase about 26% and CO conversion increase about 4%. With
20% increase of gas-liquid mass transfer coefficient (with Iron
catalyst), H2 conversions increase about 12% and CO conversion
increase about 10% and with Cobalt catalyst H2 conversions increase
about 10% and CO conversion increase about 6%. Results show that
the process is sensitive to gas-liquid mass transfer coefficient and
optimum condition operation occurs in maximum possible liquid
velocity. This velocity must be more than minimum fluidization
velocity and less than terminal velocity in such a way that avoid
catalysts particles from leaving the fluidized bed.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: The study was carried out to evaluated effect of S-gridling on fruit growth and quality of wax apple. The study was laid in Random completed block design with four replicated. Four treatment were applied as follows: S-girdling, fruit thinning plus bagging with 2,4-D sprayed, fruit thinning plus bagging and the control treatment. 2,4D was sprayed at the small bud and petal fall stage. Girdling was applied three week before flowering. The effect of all treatments on fruit growth was measured weekly. Number of flower, fruit set, fruit drop, fruit crack, and fruit quality were recorded. The result indicated that S-girdling, 2,4D application produced the lowest bud drop, fruit drop compared to untreated control. S-girdling improved faster fruit growth producing the best final fruit length and diameter compared to untreated control. S-girdling also markedly enhanced fruit set, fruit weight, and total soluble solid, reduced fruit crack, titratable acidity. On the other hand, it was noticed that with 2,4-D application also increased the fruit growth rate, improved physiological and biochemical characters of fruit than control treatment. It was concluded that S-girdling was recommended as the industry norm to increase fruit set, fruit quality in wax apple. 2,4D application had a distinctive and significant effect on most of the fruit quality characteristics assessed.
Abstract: The objective of this paper was to designing a
ventilation system to enhance the performance of roof solar collector
(RSC) for reducing heat accumulation inside the house. The RSC has
1.8 m2 surface area made of CPAC monier roof tiles on the upper part
and gypsum board on the lower part. The space between CPAC
monier and gypsum board was fixed at 14 cm.
Ventilation system of modified roof solar collector (modified
RSC) consists of 9 tubes of 0.15m diameter and installed in the
lower part of RSC. Experimental result showed that the temperature
of the room, and attic temperature. The average temperature
reduction of room of house used modified RSC is about 2oC. and the
percentage of room temperature reduction varied between 0 to 10%.
Therefore, modified RSC is an interesting option in the sense that it
promotes solar energy and conserve energy.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: A large number of chemical, bio-chemical and pollution-control processes use heterogeneous fixed-bed reactors. The use of finite hollow cylindrical catalyst pellets can enhance conversion levels in such reactors. The absence of the pellet core can significantly lower the diffusional resistance associated with the solid phase. This leads to a better utilization of the catalytic material, which is reflected in the higher values for the effectiveness factor, leading ultimately to an enhanced conversion level in the reactor. It is however important to develop a rigorous heterogeneous model for the reactor incorporating the two-dimensional feature of the solid phase owing to the presence of the finite hollow cylindrical catalyst pellet. Presently, heterogeneous models reported in the literature invariably employ one-dimension solid phase models meant for spherical catalyst pellets. The objective of the paper is to present a rigorous model of the fixed-bed reactors containing finite hollow cylindrical catalyst pellets. The reaction kinetics considered here is the widely used Michaelis–Menten kinetics for the liquid-phase bio-chemical reactions. The reaction parameters used here are for the enzymatic degradation of urea. Results indicate that increasing the height to diameter ratio helps to improve the conversion level. On the other hand, decreasing the thickness is apparently not as effective. This could however be explained in terms of the higher void fraction of the bed that causes a smaller amount of the solid phase to be packed in the fixed-bed bio-chemical reactor.
Abstract: In quality control of freeze-dried durian, crispiness is
a key quality index of the product. Generally, crispy testing has to be
done by a destructive method. A nondestructive testing of the
crispiness is required because the samples can be reused for other
kinds of testing. This paper proposed a crispiness classification
method of freeze-dried durians using fuzzy logic for decision
making. The physical changes of a freeze-dried durian include the
pores appearing in the images. Three physical features including (1)
the diameters of pores, (2) the ratio of the pore area and the
remaining area, and (3) the distribution of the pores are considered to
contribute to the crispiness. The fuzzy logic is applied for making the
decision. The experimental results comparing with food expert
opinion showed that the accuracy of the proposed classification
method is 83.33 percent.
Abstract: Biodiesel production with used frying by
transesterification reaction with methanol, using a commercial
kaolinite thermally-activated solid acid catalyst was investigated.
The surface area, the average pore diameter and pore volume of the
kaolinite catalyst were 10 m2/g, 13.0 nm and 30 mm3/g, respectively.
The optimal conditions for the transesterification reaction were
determined to be oil/methanol, in a molar ratio 1:31, temperature 160
ºC and catalyst concentration of 3% (w/w). The yield of fatty acids
methyl esters (FAME) was 92.4% after 2 h of reaction. This method
of preparation of biodiesel can be a positive alternative for utilizing
used frying corn oil for feedstock of biodiesel combined with the
inexpensive catalyst.
Abstract: The aim of this research was to calculate the thermal
properties of Au3Ni Nanowire. The molecular dynamics (MD)
simulation technique was used to obtain the effect of radius size on
the energy, the melting temperature and the latent heat of fusion at
the isobaric-isothermal (NPT) ensemble. The Quantum Sutton-Chen
(Q-SC) many body interatomic potentials energy have been used for
Gold (Au) and Nickel (Ni) elements and a mixing rule has been
devised to obtain the parameters of these potentials for nanowire
stats. Our MD simulation results show the melting temperature and
latent heat of fusion increase upon increasing diameter of nanowire.
Moreover, the cohesive energy decreased with increasing diameter of
nanowire.
Abstract: In this paper dynamics of a vapour bubble generated
due to a local energy input inside a vertical rigid cylinder and in the
absence of buoyancy forces is investigated. Different ratios of the
diameter of the rigid cylinder to the maximum radius of the bubble
are considered. The Boundary Integral Equation Method is employed
for numerical simulation of the problem. Results show that during
the collapse phase of the bubble inside a vertical rigid cylinder, two
liquid micro jets are developed on the top and bottom sides of the
vapour bubble and are directed inward. Results also show that
existence of a deposit rib inside the vertical rigid cylinder slightly
increases the life time of the bubble. It is found that by increasing the
ratio of the cylinder diameter to the maximum radius of the bubble,
the rate of the growth and collapse phases of the bubble increases
and the life time of the bubble decreases.
Abstract: Abrasive Jet Machining is an Unconventional
machining process in which the metal is removed from brittle and
hard material in the form of micro-chips. With increase in need of
materials like ceramics, composites, in manufacturing of various
Mechanical & Electronic components, AJM has become a useful
technique for micro machining. The present study highlights the
influence of different parameters like Pressure, SOD, Time, Abrasive
grain size, nozzle diameter on the Metal removal of FRP (Fiber
Reinforced Polymer) composite by Abrasive jet machining. The
results of the Experiments conducted were analyzed and optimized
with TAGUCHI method of Optimization and ANOVA for Optimal
Value.
Abstract: Heterogeneous catalysis is vital for a number of
chemical, refinery and pollution control processes. The use of
catalyst pellets of hollow cylindrical shape provide several distinct
advantages over other common shapes, and can therefore help to
enhance conversion levels in reactors. A better utilization of the
catalytic material is probably most notable of these features due to
the absence of the pellet core, which helps to significantly lower the
effect of the internal transport resistance. This is reflected in the
enhancement of the effectiveness factor. For the case of the first order
irreversible kinetics, a substantial increase in the effectiveness factor
can be obtained by varying shape parameters. Important shape
parameters of a finite hollow cylinder are the ratio of the inside to the
outside radii (κ) and the height to the diameter ratio (γ). A high value
of κ the generally helps to enhance the effectiveness factor. On the
other hand, lower values of the effectiveness factors are obtained
when the dimension of the height and the diameter are comparable.
Thus, the departure of parameter γ from the unity favors higher
effectiveness factor. Since a higher effectiveness factor is a measure
of a greater utilization of the catalytic material, higher conversion
levels can be achieved using the hollow cylindrical pellets possessing
optimized shape parameters.
Abstract: This paper present some preliminary work on the
preparation and physicochemical caracterization of nanocomposite
MFI-alumina structures based on alumina hollow fibres. The fibers
are manufactured by a wet spinning process. α-alumina particles were
dispersed in a solution of polysulfone in NMP. The resulting slurry is
pressed through the annular gap of a spinneret into a precipitation
bath. The resulting green fibres are sintered. The mechanical strength
of the alumina hollow fibres is determined by a three-point-bending
test while the pore size is characterized by bubble-point testing. The
bending strength is in the range of 110 MPa while the average pore
size is 450 nm for an internal diameter of 1 mm and external diameter
of 1.7 mm. To characterize the MFI membranes various techniques
were used for physicochemical characterization of MFI–ceramic
hollow fibres membranes: The nitrogen adsorption, X-ray
diffractometry, scanning electron microscopy combined with X
emission microanalysis. Scanning Electron Microscopy (SEM) and
Energy Dispersive Microanalysis by the X-ray were used to observe
the morphology of the hollow fibre membranes (thickness,
infiltration into the carrier, defects, homogeneity). No surface film,
has been obtained, as observed by SEM and EDX analysis and
confirmed by high temperature variation of N2 and CO2 gas
permeances before cation exchange. Local analysis and characterise
(SEM and EDX) and overall (by ICP elemental analysis) were
conducted on two samples exchanged to determine the quantity and
distribution of the cation of cesium on the cross section fibre of the
zeolite between the cavities.
Abstract: In recent years Malaysia has included renewable
energy as an alternative fuel to help in diversifying the country-s
energy reliance on oil, natural gas, coal and hydropower with
biomass and solar energy gaining priority. The scope of this paper is
to look at the designing procedures and analysis of a solar thermal
parabolic trough concentrator by simulation utilizing meteorological
data in several parts of Malaysia. Parameters which include the
aperture area, the diameter of the receiver and the working fluid may
be varied to optimize the design. Aperture area is determined by
considering the width and the length of the concentrator whereas the
geometric concentration ratio (CR) is obtained by considering the
width and diameter of the receiver. Three types of working fluid are
investigated. Theoretically, concentration ratios can be very high in
the range of 10 to 40 000 depending on the optical elements used and
continuous tracking of the sun. However, a thorough analysis is
essential as discussed in this paper where optical precision and
thermal analysis must be carried out to evaluate the performance of
the parabolic trough concentrator as the theoretical CR is not the only
factor that should be considered.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.