Abstract: Genetic algorithms (GAs) have been widely used for
global optimization problems. The GA performance depends highly
on the choice of the search space for each parameter to be optimized.
Often, this choice is a problem-based experience. The search space
being a set of potential solutions may contain the global optimum
and/or other local optimums. A bad choice of this search space
results in poor solutions. In this paper, our approach consists in
extending the search space boundaries during the GA optimization,
only when it is required. This leads to more diversification of GA
population by new solutions that were not available with fixed search
space boundaries. So, these dynamic search spaces can improve the
GA optimization performances. The proposed approach is applied to
power system stabilizer optimization for multimachine power system
(16-generator and 68-bus). The obtained results are evaluated and
compared with those obtained by ordinary GAs. Eigenvalue analysis
and nonlinear system simulation results show the effectiveness of the
proposed approach to damp out the electromechanical oscillation and
enhance the global system stability.
Abstract: Dual bell nozzle is a promising one among the altitude
adaptation nozzle concepts, which offer increased nozzle
performance in rocket engines. Its advantage is the simplicity it offers
due to the absence of any additional mechanical device or movable
parts. Hence it offers reliability along with improved nozzle
performance as demanded by future launch vehicles. Among other
issues, the flow transition to the extension nozzle of a dual bell
nozzle is one of the major issues being studied in the development of
dual bell nozzle. A parameter named over-expansion factor, which
controls the value of the wall inflection angle, has been reported to
have substantial influence in this transition process. This paper
studies, through CFD and cold flow experiments, the effect of overexpansion
factor on flow transition in dual bell nozzles.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: In this paper, the implementation of low power,
high throughput convolutional filters for the one dimensional
Discrete Wavelet Transform and its inverse are presented. The
analysis filters have already been used for the implementation of a
high performance DWT encoder [15] with minimum memory
requirements for the JPEG 2000 standard. This paper presents the
design techniques and the implementation of the convolutional filters
included in the JPEG2000 standard for the forward and inverse DWT
for achieving low-power operation, high performance and reduced
memory accesses. Moreover, they have the ability of performing
progressive computations so as to minimize the buffering between
the decomposition and reconstruction phases. The experimental
results illustrate the filters- low power high throughput characteristics
as well as their memory efficient operation.
Abstract: This paper proposes a VPN Accelerator Board
(VPN-AB), a virtual private network (VPN) protocol designed for
trust channel security system (TCSS). TCSS supports safety
communication channel between security nodes in internet. It
furnishes authentication, confidentiality, integrity, and access control
to security node to transmit data packets with IPsec protocol. TCSS
consists of internet key exchange block, security association block,
and IPsec engine block. The internet key exchange block negotiates
crypto algorithm and key used in IPsec engine block. Security
Association blocks setting-up and manages security association
information. IPsec engine block treats IPsec packets and consists of
networking functions for communication. The IPsec engine block
should be embodied by H/W and in-line mode transaction for high
speed IPsec processing. Our VPN-AB is implemented with high speed
security processor that supports many cryptographic algorithms and
in-line mode. We evaluate a small TCSS communication environment,
and measure a performance of VPN-AB in the environment. The
experiment results show that VPN-AB gets a performance throughput
of maximum 15.645Gbps when we set the IPsec protocol with
3DES-HMAC-MD5 tunnel mode.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A number of studies have reported increased cardiometabolic risk, premature ardiovascular disease and incidence of type 2 diabetes. Rugby union players have somatotypes very similar
to National Football league players which suggest that rugby players may have similar health risks. The International Golden Oldies World Rugby Festival (GORF) provided a
unique opportunity to investigate the demographics of veteran rugby players. METHODOLOGIES: A cross-sectional, observational study was completed using an online web-based
questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one sample t-test (50yrs) and Chi-square test. RESULTS: A total of 216 veteran rugby competitors
(response rate = 6.8%) representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0), participated in the online survey. As a group, the incidence of current smokers was low at 8.8%
(avg 72.4 cigs/wk) whilst the percentage consuming alcohol
was high (93.1% (avg 11.2 drinks/wk). Competitors reported
the following top six chronic diseases/disorders; hypertension
(18.6%), arthritis (OA/RA, 11.5%), asthma (9.3%),
hyperlipidemia (8.2%), diabetes (all types, 7.5%) and gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to
the Australian general population (Australian Bureau of Statistics data, n=18,000), GORF competitors had a
Climstein Mike, Walsh Joe (corresponding author) and Burke Stephen
School of Exercise Science, Australian Catholic University, 25A Barker Road,
Strathfield, Sydney, NSW, 2016, Australia (e-mail:
[email protected], [email protected],
[email protected]).
John Best is with Orthosports, 160 Belmore Rd., Randwick, Sydney,NSW
2031, Australia (e-mail: [email protected]).
Heazlewood, Ian Timothy is with School of Environmental and Life
Sciences, Faculty Education, Health and Science, Charles Darwin University,
Precinct Yellow Building 2, Charles Darwin University, NT 0909, Australia
(e-mail: [email protected]).
Kettunen Jyrki Arcada University of Applied Sciences, Jan-Magnus
Janssonin aukio 1, FI-00550, Helsinki, Finland (e-mail:
[email protected]).
Adams Kent is with California State University Monterey Bay, Kinesiology Department, 100 Campus Center, Seaside, CA., 93955, USA (email: [email protected]).
DeBeliso Mark is with Department of Physical Education and Human
Performance, Southern Utah University, 351 West University Blvd, Cedar
City, Utah, USA (e-mail: [email protected]).
significantly lower incidence of anxiety (p
Abstract: In this paper, with the purpose of further reducing the
complexity of the system, while keeping its temporal and spatial
focusing performance, we investigate the possibility of using optimal
one bit time reversal (TR) system for impulse radio ultra wideband
multi-user wireless communications. The results show that, by optimally
selecting the number of used taps in the pre-filter the optimal
one bit TR system can outperform the full one bit TR system. In
some cases, the temporal and spatial focusing performance of the
optimal one bit TR system appears to be compatible with that of the
original TR system. This is a significant result as the overhead cost
is much lower than it is required in the original TR system.
Abstract: This paper proposes an alternative control mechanism
for an interactive Pan/Tilt/Zoom (PTZ) camera control system.
Instead of using a mouse or a joystick, the proposed mechanism
utilizes a Nintendo Wii remote and infrared (IR) sensor bar. The Wii
remote has buttons that allows the user to control the movement of a
PTZ camera through Bluetooth connectivity. In addition, the Wii
remote has a built-in motion sensor that allows the user to give
control signals to the PTZ camera through pitch and roll movement.
A stationary IR sensor bar, placed at some distance away opposite the
Wii remote, enables the detection of yaw movement. In addition, the
Wii remote-s built-in IR camera has the ability to detect its spatial
position, and thus generates a control signal when the user moves the
Wii remote. Some experiments are carried out and their performances
are compared with an industry-standard PTZ joystick.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: In this paper a data miner based on the learning
automata is proposed and is called LA-miner. The LA-miner extracts
classification rules from data sets automatically. The proposed
algorithm is established based on the function optimization using
learning automata. The experimental results on three benchmarks
indicate that the performance of the proposed LA-miner is
comparable with (sometimes better than) the Ant-miner (a data miner
algorithm based on the Ant Colony optimization algorithm) and CNZ
(a well-known data mining algorithm for classification).
Abstract: Statistical selection procedures are used to select the
best simulated system from a finite set of alternatives. In this paper,
we present a procedure that can be used to select the best system
when the number of alternatives is large. The proposed procedure
consists a combination between Ranking and Selection, and Ordinal
Optimization procedures. In order to improve the performance of Ordinal
Optimization, Optimal Computing Budget Allocation technique
is used to determine the best simulation lengths for all simulation
systems and to reduce the total computation time. We also argue
the effect of increment in simulation samples for the combined
procedure. The results of numerical illustration show clearly the effect
of increment in simulation samples on the proposed combination of
selection procedure.
Abstract: Enterprise Wide Information Systems (EWIS)
implementation involves the entire business and will require changes
throughout the firm. Because of the scope, complexity and
continuous nature of ERP, the project-based approach to managing
the implementation process resulted in failure rates of between 60%
and 80%. In recent years ERP systems have received much attention.
The organizational relevance and risk of ERP projects make it
important for organizations to focus on ways to make ERP
implementation successful. Once these systems are in place,
however, their performance depends on the identified macro
variables viz. 'Business Process', 'Decision Making' and 'Individual
/ Group working'. The questionnaire was designed and administered.
The responses from 92 organizations were compiled. The
relationship of these variables with EWIS performance is analyzed
using inferential statistical measurements. The study helps to
understand the performance of model presented. The study suggested
in keeping away from the calamities and thereby giving the
necessary competitive edge. Whenever some discrepancy is
identified during the process of performance appraisal care has to be
taken to draft necessary preventive measures. If all these measures
are taken care off then the EWIS performance will definitely deliver
the results.
Abstract: There is a growing body of evidence to support the
proposition of product take back for remanufacturing particularly
within the context of Extended Producer Responsibility (EPR).
Remanufacturing however presents challenges unlike that of
traditional manufacturing environments due to its high levels of
uncertainty which may further distract organizations from
considering its potential benefits. This paper presents a novel
modeling approach for evaluating the uncertainty of part failures
within the remanufacturing process and its impact on economic and
environmental performance measures. This paper presents both the
theoretical modeling approach and an example of its use in
application.
Abstract: The extract of milk thistle contains a mix of flavonolignans termed silymarine.. In order to analysis influence of growth regulators, genotype, explant and subculture on the accumulation of flavonolignans, a study was carried out by using two genotype (Budakalszi and Noor abad moghan cultivars), cotyledon and hypocotyle explants, solid media of MS supplemented by different combinations of two growth regulators; Kinetin (0.1, 1 mg/l) and 2,4-D (1, 2 mg/l). Seeds of the plant were germinated in MS media whitout growth regulators in growth chamber at 26°C and darkness condition. In order to callus induction, the culture media was supplemented whit different concentrations of 2,4-D and kinetin. Calli obtained from explants were sub-cultured four times into the fresh media of the first experiment. flavonoides was extracted from calli in four subcultures. The flavonoid components were determined by high- performance liquid choromatography (HPLC) and separated into Taxifolin, Silydianin+Silychristin, Silybin A+B and Isosilybin A+B. Results showed that with increasing callus age, increased accumulation of silybin A+B, but reduced Isosilybin A+B content. Highest accumulation of Taxifolin was observed at first calli. Calli produced from cotyledon explant of Budakalszi cultivar were superior for Silybin A+B, where calli from hypocotyl explant produced higher amount of Taxifolin and Silydianin+Silychristin. The best cultivar for Silymarin production in this study was Budakalszi cultivar. High amount of SBN A+B and TXF were obtained from hypocotil explant.
Abstract: In this paper we propose an enhanced equalization technique for multi-carrier code division multiple access (MC-CDMA). This method is based on the control of Equal Gain Combining (EGC) technique. Indeed, we introduce a new level changer to the EGC equalizer in order to adapt the equalization parameters to the channel coefficients. The optimal equalization level is, first, determined by channel training. The new approach reduces drastically the mutliuser interferences caused by interferes, without increasing the noise power. To compare the performances of the proposed equalizer, the theoretical analysis and numerical performances are given.
Abstract: A method for solving linear and non-linear Goursat
problem is given by using the two-dimensional differential transform
method. The approximate solution of this problem is calculated in
the form of a series with easily computable terms and also the exact
solutions can be achieved by the known forms of the series solutions.
The method can easily be applied to many linear and non-linear
problems and is capable of reducing the size of computational work.
Several examples are given to demonstrate the reliability and the
performance of the presented method.
Abstract: A high performance thin layer chromatography
system (HPTLC) for the separation of vitamin B2 and B12 has been
developed. The separation was successfully using a solvent system of
methanol, water, ammonia 7.3.1 (V/V) as mobile phase on HPTLC
plates impregnated with boric acid. The effect of other mobile phases
on the separation of vitamins was also examined. The method is
based on different behavior of investigated compounds in
impregnated TLC plates with different amount of boric acid. The Rf
values of vitamin B2 and B12 are considered on non impregnated
and impregnated silica gel HPTLC plate with boric acid. The effect
of boric acid in the mobile phase and on HPTLC plates on the RF
values of the vitamins has also been studied.
Abstract: The group mutual exclusion (GME) problem is an
interesting generalization of the mutual exclusion problem. Several
solutions of the GME problem have been proposed for message
passing distributed systems. However, none of these solutions is
suitable for real time distributed systems. In this paper, we propose a
token-based distributed algorithms for the GME problem in soft real
time distributed systems. The algorithm uses the concepts of priority
queue, dynamic request set and the process state. The algorithm uses
first come first serve approach in selecting the next session type
between the same priority levels and satisfies the concurrent
occupancy property. The algorithm allows all n processors to be
inside their CS provided they request for the same session. The
performance analysis and correctness proof of the algorithm has also
been included in the paper.
Abstract: Model Predictive Control has been previously applied
to supply chain problems with promising results; however hitherto
proposed systems possessed no information on future demand. A
forecasting methodology will surely promote the efficiency of
control actions by providing insight on the future. A complete supply
chain management framework that is based on Model Predictive
Control (MPC) and Time Series Forecasting will be presented in this
paper. The proposed framework will be tested on industrial data in
order to assess the efficiency of the method and the impact of
forecast accuracy on overall control performance of the supply chain.
To this end, forecasting methodologies with different characteristics
will be implemented on test data to generate forecasts that will serve
as input to the Model Predictive Control module.
Abstract: In designing river intakes and diversion structures, it is paramount that the sediments entering the intake are minimized or, if possible, completely separated. Due to high water velocity, sediments can significantly damage hydraulic structures especially when mechanical equipment like pumps and turbines are used. This subsequently results in wasting water, electricity and further costs. Therefore, it is prudent to investigate and analyze the performance of lateral intakes affected by sediment control structures. Laboratory experiments, despite their vast potential and benefits, can face certain limitations and challenges. Some of these include: limitations in equipment and facilities, space constraints, equipment errors including lack of adequate precision or mal-operation, and finally, human error. Research has shown that in order to achieve the ultimate goal of intake structure design – which is to design longlasting and proficient structures – the best combination of sediment control structures (such as sill and submerged vanes) along with parameters that increase their performance (such as diversion angle and location) should be determined. Cost, difficulty of execution and environmental impacts should also be included in evaluating the optimal design. This solution can then be applied to similar problems in the future. Subsequently, the model used to arrive at the optimal design requires high level of accuracy and precision in order to avoid improper design and execution of projects. Process of creating and executing the design should be as comprehensive and applicable as possible. Therefore, it is important that influential parameters and vital criteria is fully understood and applied at all stages of choosing the optimal design. In this article, influential parameters on optimal performance of the intake, advantages and disadvantages, and efficiency of a given design are studied. Then, a multi-criterion decision matrix is utilized to choose the optimal model that can be used to determine the proper parameters in constructing the intake.