Abstract: This paper describes an optimization tool-based
design strategy for a Current Mode Logic CML divide-by-2 circuit.
Representing a building block for output frequency generation in a
RFID protocol based-frequency synthesizer, the circuit was designed
to minimize the power consumption for driving of multiple loads
with unbalancing (at transceiver level). Implemented with XFAB
XC08 180 nm technology, the circuit was optimized through
MunEDA WiCkeD tool at Cadence Virtuoso Analog Design
Environment ADE.
Abstract: The chemical and physical characteristics of rainwater
harvested from a typical rooftop were progressively studied. The
samples of rainwater collected were analyzed for pH, major ion
concentrations, TDS, turbidity, conductivity. All the Physicochemical
constituents fell within the WHO guideline limits at some points as
rainfall progresses except the pH. All the components of rainwater
quality measured during the study showed higher concentrations
during the early stages of rainfall and reduce as time progresses.
There was a downward trend in terms of pH as rain progressed, with
18% of the samples recording pH below the WHO limit of 6.5-8.0. It
was observed that iron concentration was above the WHO threshold
value of 0.3 mg/l on occasions of heavy rains. The results revealed
that most of physicochemical characteristics of rainwater samples
were generally below the WHO threshold, as such, the rainwater
characteristics showed satisfactory conditions in terms of
physicochemical constituents.
Abstract: We present a refined multiscale Shannon entropy for
analyzing electroencephalogram (EEG), which reflects the underlying
dynamics of EEG over multiple scales. The rationale behind
this method is that neurological signals such as EEG possess
distinct dynamics over different spectral modes. To deal with the
nonlinear and nonstationary nature of EEG, the recently developed
empirical mode decomposition (EMD) is incorporated, allowing a
decomposition of EEG into its inherent spectral components, referred
to as intrinsic mode functions (IMFs). By calculating the Shannon
entropy of IMFs in a time-dependent manner and summing them over
adaptive multiple scales, it results in an adaptive subscale entropy
measure of EEG. Simulation and experimental results show that
the proposed entropy properly reveals the dynamical changes over
multiple scales.
Abstract: Rapid growth of Information Technologies (IT) has
had huge influence on enterprises, and it has contributed to its
promotion and increasingly extensive use in enterprises. Information
Technologies have to a large extent determined the processes taking
place in an enterprise; what is more, IT development has brought the
need to adopt a brand new approach to human resources management
in an enterprise. The use of IT in human resource management
(HRM) is of high importance due to the growing role of information
and information technologies. The aim of this paper is to evaluate the
use of information technologies in human resources management in
enterprises. These practices will be presented in the following areas:
recruitment and selection, development and training, employee
assessment, motivation, talent management, personnel service.
Results of conducted survey show diversity of solutions applied in
particular areas of human resource management. In the future, further
development in this area should be expected, as well as integration of
individual HRM areas, growing mobile-enabled HR processes and
their transfer into the cloud. Presented IT solutions applied in HRM
are highly innovative, which is of great significance due to their
possible implementation in other enterprises.
Abstract: Software fault prediction models are created by using
the source code, processed metrics from the same or previous version
of code and related fault data. Some company do not store and keep
track of all artifacts which are required for software fault prediction.
To construct fault prediction model for such company, the training
data from the other projects can be one potential solution. Earlier we
predicted the fault the less cost it requires to correct. The training
data consists of metrics data and related fault data at function/module
level. This paper investigates fault predictions at early stage using the
cross-project data focusing on the design metrics. In this study,
empirical analysis is carried out to validate design metrics for cross
project fault prediction. The machine learning techniques used for
evaluation is Naïve Bayes. The design phase metrics of other projects
can be used as initial guideline for the projects where no previous
fault data is available. We analyze seven datasets from NASA
Metrics Data Program which offer design as well as code metrics.
Overall, the results of cross project is comparable to the within
company data learning.
Abstract: The concept of national security in Iran is a
permanently effective factor in acceptance or rejection of many
international obligations. These obligations had been defined
according to the type of legislation of Iran in many aspects.
Therefore, there are several treaties at international level which
requires Iran’s security to come in contact with obligations in these
treaties in a way that an obstacle to join to them and their passage in
parliament. This issue is a typical category which every country pays
attention to be accepted in treaties or to include their national
security in that treaties and also they can see the related treaties from
this perspective, but this issue that 'what is the concept of Iran’s
national security', and 'To what extent it is changed in recent years,
especially after Islamic Revolution' are important issues that can be
criticized. Thus, this study is trying to assess singed treaties from the
perspective of Iran’s national security according of the true meaning
of treaty and to investigate how the international treaties may be in
conflict with Iran’s national security.
Abstract: On the basis of the theory of nonlinear elasticity, the
effect of homogeneous stress on the propagation of Lamb waves in
an initially isotropic hyperelastic plate is analysed. The equations
governing the propagation of small amplitude waves in the prestressed
plate are derived using the theory of small deformations
superimposed on large deformations. By enforcing traction free
boundary conditions at the upper and lower surfaces of the plate,
acoustoelastic dispersion equations for Lamb wave propagation are
obtained, which are solved numerically. Results are given for an
aluminum plate subjected to a range of applied stresses.
Abstract: In educational technology, the idea of innovation is
usually tethered to contemporary technological inventions and
emerging technologies. Yet, using long-known technologies in ways
that are pedagogically or experimentially new can reposition them as
emerging educational technologies. In this study we explore how a
subtle pivot in pedagogical thinking led to an innovative education
technology. We describe the design and implementation of an online
writing tool that scaffolds students in the evaluation of their own
informational texts. We think about how pathways to innovation can
emerge from pivots, namely a leveraging of longstanding practices in
novel ways has the potential to cultivate new opportunities for
learning. We first unpack Infowriter in terms of its design, then we
describe some results of a study in which we implemented an
intervention which included our designed application.
Abstract: Through use of novel modern/rapid processing
techniques such as screen printing and Near-Infrared (NIR) radiative
curing, process time for the sintering of sintered nickel plaques,
applicable to alkaline nickel battery chemistries, has been drastically
reduced from in excess of 200 minutes with conventional convection
methods to below 2 minutes using NIR curing methods. Steps have
also been taken to remove the need for forming gas as a reducing
agent by implementing carbon as an in-situ reducing agent, within the
ink formulation.
Abstract: An important problem for the CaSO4/CaSO4･1/2H2O
Chemical heat pump (CHP) is that the material is deactivated through
repetitive reaction between hydration and dehydration in which the
crystal phase of the material is transformed from III-CaSO4 to
II-CaSO4. We investigated suppression on the phase change by adding
a sulfated compound. The most effective material was MgSO4. MgSO4
doping increased the durability of CaSO4 in the actual CHP repetitive
cycle of hydration/dehydration to 3.6 times that of undoped CaSO4.
The MgSO4-doped CaSO4 showed a higher phase transition
temperature and activation energy for crystal transformation from
III-CaSO4 to II-CaSO4. MgSO4 doping decreased the crystal lattice
size of CaSO4･1/2H2O and II-CaSO4 to smaller than that of undoped
CaSO4. Modification of the crystal structure is considered to be related
to the durability change in CaSO4 resulting from MgSO4 doping.
Abstract: Super steel materials play a vital role in the
construction and fabrication of structural, piping and pipeline
components. In assuring the integrity of onshore and offshore
operating systems, they enable life cycle costs to be minimized. In
this context, Duplex stainless steel (DSS) material related welding on
constructions and fabrications plays a significant role in maintaining
and assuring integrity at an optimal expenditure over the life cycle of
production and process systems as well as associated structures. In
DSS welding, factors such as gap geometry, shielding gas supply
rate, welding current, and type of the welding process are vital to the
final joint performance. Hence, an experimental investigation has
been performed using an engineering robust design approach
(ERDA) to investigate the optimal settings that generate optimal
super DSS (i.e. UNS S32750) joint performance. This manuscript
illustrates the mathematical approach and experimental design,
optimal parameter settings and results of the verification experiment.
Abstract: A Japanese manga character, Doraemon, was made by
Fujiko F. Fujio in 1969, was made into animation in 1973. The main
character, Doraemon, is a robot cat, and is a well-known Japanese
animated character. However, Doraemon is not only regarded as an
animation character but it is also used in educational and technological
programs in Japan.
This paper focuses on the background of Doraemon, educational
and technological perspectives on Doraemon, and comparison of the
original Japanese animation and the US remade version, and the
animator Fujiko’s dreams and hopes for Doraemon will be examined.
Since Doraemon has been exported as animation and manga to
overseas, perspectives toward Doraemon have changed. For example,
changes of stories and characters can been seen in the present
Doraemon animation. Not only the overseas TV productions which
broadcast Doraemon but also the Japanese production has to consider
violence, sexuality, etc. when editing episodes. Because of
representation of cultural differences, Japanese animation is thought to
contain more violence, discrimination, and sexuality in animation.
With responses from overseas, the Japanese production was cautious
about the US remade version. They cared about the US Broadcast
Standard, and tried to consider US customs and culture in the US
remade version. Seeing the difference, acculturation is necessary for
exports of animation overseas. Moreover, observing different aspects
of Doraemon domestically, Doraemon provides dreams and hopes to
children.
Abstract: This paper investigates simple implicit force control
algorithms realizable with industrial robots. A lot of approaches
already published are difficult to implement in commercial robot
controllers, because the access to the robot joint torques is necessary
or the complete dynamic model of the manipulator is used. In
the past we already deal with explicit force control of a position
controlled robot. Well known schemes of implicit force control are
stiffness control, damping control and impedance control. Using such
algorithms the contact force cannot be set directly. It is further
the result of controller impedance, environment impedance and
the commanded robot motion/position. The relationships of these
properties are worked out in this paper in detail for the chosen
implicit approaches. They have been adapted to be implementable
on a position controlled robot. The behaviors of stiffness control
and damping control are verified by practical experiments. For this
purpose a suitable test bed was configured. Using the full mechanical
impedance within the controller structure will not be practical in the
case when the robot is in physical contact with the environment. This
fact will be verified by simulation.
Abstract: Thousands of organisations store important and
confidential information related to them, their customers, and their
business partners in databases all across the world. The stored data
ranges from less sensitive (e.g. first name, last name, date of birth) to
more sensitive data (e.g. password, pin code, and credit card
information). Losing data, disclosing confidential information or
even changing the value of data are the severe damages that
Structured Query Language injection (SQLi) attack can cause on a
given database. It is a code injection technique where malicious SQL
statements are inserted into a given SQL database by simply using a
web browser. In this paper, we propose an effective pattern
recognition neural network model for detection and classification of
SQLi attacks. The proposed model is built from three main elements
of: a Uniform Resource Locator (URL) generator in order to generate
thousands of malicious and benign URLs, a URL classifier in order
to: 1) classify each generated URL to either a benign URL or a
malicious URL and 2) classify the malicious URLs into different
SQLi attack categories, and a NN model in order to: 1) detect either a
given URL is a malicious URL or a benign URL and 2) identify the
type of SQLi attack for each malicious URL. The model is first
trained and then evaluated by employing thousands of benign and
malicious URLs. The results of the experiments are presented in
order to demonstrate the effectiveness of the proposed approach.
Abstract: Extracting and determining chlorophyll pigments
(chlorophyll a and b) in green leaves are the procedures based on the
solvent extraction of pigments in samples using N,Ndimethylformamide
as the extractant. In this study, two species of
soluble inorganic selenium forms, selenite (SeIV) and selenate (SeVI)
at different concentrations were investigated on maize plants that
were growing in nutrient solutions during 2 weeks and at the end of
the experiment, amounts of chlorophyll a and b for first and second
leaves of maize were measured. In accordance with the results we
observed that our regarded Se concentrations in both forms of SeIV
and SeVI were not effective on maize plants’ chlorophyll a and b
significantly although high level of 3 mg.kg-1 SeIV had negative affect
on growth of the samples that had been treated by it but about SeVI
samples we did not observe this state and our different considered
SeVI concentrations were not toxic for maize plants.
Abstract: This paper presents a numerical investigation of two
horizontally mounted four-lobed swirl pipes in terms of swirl
induction effectiveness into flows passing through them. The swirl
flows induced by the two swirl pipes have the potential to improve
the efficiency of Clean-In-Place procedures in a closed processing
system by local intensification of hydrodynamic impact on the
internal pipe surface. Pressure losses, swirl development within the
two swirl pipe, swirl induction effectiveness, swirl decay and wall
shear stress variation downstream of two swirl pipes are analyzed and
compared. It was found that a shorter length of swirl inducing pipe
used in joint with transition pipes is more effective in swirl induction
than when a longer one is used, in that it has a less constraint to the
induced swirl and results in slightly higher swirl intensity just
downstream of it with the expense of a smaller pressure loss. The
wall shear stress downstream of the shorter swirl pipe is also slightly
larger than that downstream of the longer swirl pipe due to the
slightly higher swirl intensity induced by the shorter swirl pipe. The
advantage of the shorter swirl pipe in terms of swirl induction is more
significant in flows with a larger Reynolds Number.
Abstract: Aim of this work is to determine the theoretical and
experimental properties of filament wound glass fiber/epoxy resin
composite pipes with different winding design subjected under
bending. For determination of bending strength of composite samples
three point bending tests were conducted. Good correlation between
theoretical and experimental results has been obtained, where sample
No4 has shown the highest value of bending strength. All samples
have demonstrated matrix cracking and fiber failure followed by
layers delamination during testing. Also, it was found that smaller
winding angles lead to an increase in bending stress. From presented
results good merger between glass fibers and epoxy resin was
confirmed by SEM analysis.
Abstract: In this study, firstly democratic thoughts which
directly or indirectly affect economic development and/or the
interaction between authoritarian regimes and the economic
development and the direction and channels of this interaction were
studied and then the study tried to determine how democracy affects
economic development. It was concluded that the positive
contributions of democracy to economic development were more
determinant than the effects that were either negative or restrictive in
terms of development. When compared to autocracy, since
democracy is more successful in managing social conflicts, ensuring
political stability and preventing social disasters such as famine, it
contributes more to economic development. Democracy also
facilitates delegation of authority, provides a stable investment
environment and accelerates mobilization of resources in accordance
with economic growth/development. Democracy leads to an increase
in human capital accumulation and increases the growth rate through
reducing income inequality. It can be said that democratic regimes
are the most appropriate ones in terms of increasing economic
performance and supporting economic development through their
strong institutional structures and the assurance they will ensure in
property rights.
Abstract: Non-crimp 3D orthogonal fabric composite is one of
the textile-based composite materials that are rapidly developing
light-weight engineering materials. The present paper focuses on
geometric and micromechanical modeling of non-crimp 3D
orthogonal carbon fabric and composites reinforced with it for
aerospace applications. In this research meso-finite element (FE)
modeling employs for stress analysis in different load conditions.
Since mechanical testing of expensive textile carbon composites with
specific application isn't affordable, simulation composite in a virtual
environment is a helpful way to investigate its mechanical properties
in different conditions.
Abstract: Background: Worldwide, at least 2.8 million people
die each year as a result of being overweight or obese, and 35.8
million (2.3%) of global DALYs are caused by overweight or
obesity. Obesity is acknowledged as one of the burning public
health problems reducing life expectancy and quality of life. The
body composition analysis of the university population is essential
in assessing the nutritional status, as well as the risk of developing
diseases associated with abnormal body fat content so as to make
nutritional recommendations. Objectives: The main aim was to
determine the prevalence of obesity and overweight in University
students using Anthropometric analysis and BIA methods. Material
and Methods: In this cross-sectional study, 283 university students
participated. The body composition analysis was undertaken by
using mainly: i) Anthropometric Measurement: Height, Weight,
BMI, waist circumference, hip circumference and skin fold
thickness, ii) Bio-electrical impedance was used for analysis of
body fat mass, fat percent and visceral fat which was measured by
Tanita SC-330P Professional Body Composition Analyzer. The
data so collected were compiled in MS Excel and analyzed for
males and females using SPSS 16. Results and Discussion: The
mean age of the male (n= 153) studied subjects was 25.37 ±2.39
years and females (n=130) was 22.53 ±2.31. The data of BIA
revealed very high mean fat per cent of the female subjects i.e.
30.3±6.5 per cent whereas mean fat per cent of the male subjects
was 15.60±6.02 per cent indicating a normal body fat range. The
findings showed high visceral fat of both males (12.92±3.02) and
females (16.86±4.98). BMI, BF% and WHR were higher among
females, and BMI was higher among males. The most evident
correlation was verified between BF% and WHR for female
students (r=0.902; p