Abstract: Proof of controlling crack width is a basic condition
for securing suitable performance in serviceability limit state. The
cracking in concrete can occur at any time from the casting of time to
the years after the concrete has been set in place. Most codes struggle
with offering procedure for crack width calculation. There is lack in
availability of design charts for designers to compute crack width
with ease. The focus of the study is to utilize design charts and
parametric equations in calculating crack width with minimum error.
The paper contains a simplified procedure to calculate crack width
for reinforced concrete (RC) sections subjected to bending with axial
tensile force following the guidelines of Euro code [DS EN-1992-1-1
& DS EN-1992-1-2]. Numerical examples demonstrate the
application of the suggested procedure. Comparison with parallel
analytical tools supports the validity of result and show the
percentage deviation of crack width in both the procedures. The
technique is simple, user friendly and ready to evolve for a greater
spectrum of section sizes and materials.
Abstract: Presently, engine cooling pump is driven by toothed
belt. Therefore, the pump speed is dependent on engine speed which
varies their output. At normal engine operating conditions (Higher
RPM and low load, Higher RPM and high load), mechanical water
pumps in existing engines are inevitably oversized and so the use of
an electric water pump together with state-of-the-art thermal
management of the combustion engine has measurable advantages.
Demand-driven cooling, particularly in the cold-start phase, saves
fuel (approx 3 percent) and leads to a corresponding reduction in
emissions. The lack of dependence on a mechanical drive also results
in considerable flexibility in component packaging within the engine
compartment. This paper describes the testing and comparison of
existing mechanical water pump with that of the electric water pump.
When the existing mechanical water pump is replaced with the new
electric water pump the percentage gain in system efficiency is also
discussed.
Abstract: This paper presents optimization of makespan for ‘n’
jobs and ‘m’ machines flexible job shop scheduling problem with
sequence dependent setup time using genetic algorithm (GA)
approach. A restart scheme has also been applied to prevent the
premature convergence. Two case studies are taken into
consideration. Results are obtained by considering crossover
probability (pc = 0.85) and mutation probability (pm = 0.15). Five
simulation runs for each case study are taken and minimum value
among them is taken as optimal makespan. Results indicate that
optimal makespan can be achieved with more than one sequence of
jobs in a production order.
Abstract: Many of the ever-growing elderly population require
exercise, such as running, for health management. One important
element of a runner’s training is the choice of shoes for exercise; shoes
are important because they provide the interface between the feet and
road. When we purchase shoes, we may instinctively choose a pair
after trying on many different pairs of shoes. Selecting the shoes
instinctively may work, but it does not guarantee a suitable fit for
running activities. Therefore, if we could select suitable shoes for each
runner from the viewpoint of brain activities, it would be helpful for
validating shoe selection. In this paper, we describe how brain
activities show different characteristics during particular task,
corresponding to different properties of shoes. Using five subjects, we
performed a verification experiment, applying weight, softness, and
flexibility as shoe properties. In order to affect the shoe property’s
differences to the brain, subjects run for 10 min. Before and after
running, subjects conducted a paced auditory serial addition task
(PASAT) as the particular task; and the subjects’ brain activities
during the PASAT are evaluated based on oxyhemoglobin and
deoxyhemoglobin relative concentration changes, measured by
near-infrared spectroscopy (NIRS). When the brain works actively,
oxihemoglobin and deoxyhemoglobin concentration drastically
changes; therefore, we calculate the maximum values of concentration
changes. In order to normalize relative concentration changes after
running, the maximum value are divided by before running maximum
value as evaluation parameters. The classification of the groups of
shoes is expressed on a self-organizing map (SOM). As a result,
deoxyhemoglobin can make clusters for two of the three types of
shoes.
Abstract: The Smart Help for persons with disability (PWD) is a
part of the project SMARTDISABLE which aims to develop relevant
solution for PWD that target to provide an adequate workplace
environment for them. It would support PWD needs smartly through
smart help to allow them access to relevant information and
communicate with other effectively and flexibly, and smart editor
that assist them in their daily work. It will assist PWD in knowledge
processing and creation as well as being able to be productive at the
work place. The technical work of the project involves design of a
technological scenario for the Ambient Intelligence (AmI) - based
assistive technologies at the workplace consisting of an integrated
universal smart solution that suits many different impairment
conditions and will be designed to empower the Physically disabled
persons (PDP) with the capability to access and effectively utilize the
ICTs in order to execute knowledge rich working tasks with
minimum efforts and with sufficient comfort level. The proposed
technology solution for PWD will support voice recognition along
with normal keyboard and mouse to control the smart help and smart
editor with dynamic auto display interface that satisfies the
requirements for different PWD group. In addition, a smart help will
provide intelligent intervention based on the behavior of PWD to
guide them and warn them about possible misbehavior. PWD can
communicate with others using Voice over IP controlled by voice
recognition. Moreover, Auto Emergency Help Response would be
supported to assist PWD in case of emergency. This proposed
technology solution intended to make PWD very effective at the
work environment and flexible using voice to conduct their tasks at
the work environment. The proposed solution aims to provide
favorable outcomes that assist PWD at the work place, with the
opportunity to participate in PWD assistive technology innovation
market which is still small and rapidly growing as well as upgrading
their quality of life to become similar to the normal people at the
workplace. Finally, the proposed smart help solution is applicable in
all workplace setting, including offices, manufacturing, hospital, etc.
Abstract: PVC foam-fly ash composites (PVC-FA) are
characterized for their structural, morphological, mechanical and
thermal properties. The tensile strength of the composites increased
modestly with higher fly ash loading, while there was a significant
increase in the elastic modulus for the same composites. On the other
hand, a decrease in elongation at UTS was observed upon increasing
fly ash content due to increased rigidity of the composites. Similarly,
the flexural modulus increased as the fly ash loading increased,
where the composites containing 25 phr fly ash showed the highest
flexural strength. Thermal properties of PVC-fly ash composites were
determined by Thermo Gravimetric Analysis (TGA). The
microstructural properties were studied by Scanning Electron
Microscopy (SEM). SEM results confirm that fly ash particles were
mechanically interlocked in PVC matrix with good interfacial
interaction with the matrix. Particle agglomeration and debonding
was observed in samples containing higher amounts of fly ash.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: Structured Query Language (SQL) is the standard de facto language to access and manipulate data in a relational database. Although SQL is a language that is simple and powerful, most novice users will have trouble with SQL syntax. Thus, we are presenting SQL generator tool which is capable of translating actions and displaying SQL commands and data sets simultaneously. The tool was developed based on Model-View-Controller (MVC) pattern. The MVC pattern is a widely used software design pattern that enforces the separation between the input, processing, and output of an application. Developers take full advantage of it to reduce the complexity in architectural design and to increase flexibility and reuse of code. In addition, we use White-Box testing for the code verification in the Model module.
Abstract: Regardless of the manufacturing process used,
subtractive or additive, material, purpose and application, produced
components are conventionally solid mass with more or less complex
shape depending on the production technology selected. Aspects
such as reducing the weight of components, associated with the low
volume of material required and the almost non-existent material
waste, speed and flexibility of production and, primarily, a high
mechanical strength combined with high structural performance, are
competitive advantages in any industrial sector, from automotive,
molds, aviation, aerospace, construction, pharmaceuticals, medicine
and more recently in human tissue engineering. Such features,
properties and functionalities are attained in metal components
produced using the additive technique of Rapid Prototyping from
metal powders commonly known as Selective Laser Melting (SLM),
with optimized internal topologies and varying densities. In order to
produce components with high strength and high structural and
functional performance, regardless of the type of application, three
different internal topologies were developed and analyzed using
numerical computational tools. The developed topologies were
numerically submitted to mechanical compression and four point
bending testing. Finite Element Analysis results demonstrate how
different internal topologies can contribute to improve mechanical
properties, even with a high degree of porosity relatively to fully
dense components. Results are very promising not only from the
point of view of mechanical resistance, but especially through the
achievement of considerable variation in density without loss of
structural and functional high performance.
Abstract: Comprehensive numerical studies have been carried
out to examine the best aerodynamic performance of subsonic aircraft
at different winglet cant angles using a validated 3D k-ω SST model.
In the parametric analytical studies NACA series of airfoils are
selected. Basic design of the winglet is selected from the literature
and flow features of the entire wing including the winglet tip effects
have been examined with different cant angles varying from 150 to
600 at different angles of attack up to 140. We have observed, among
the cases considered in this study that a case, with 150 cant angle the
aerodynamics performance of the subsonic aircraft during takeoff
was found better up to an angle of attack of 2.80 and further its
performance got diminished at higher angles of attack. Analyses
further revealed that increasing the winglet cant angle from 150 to 600
at higher angles of attack could negate the performance deterioration
and additionally it could enhance the peak CL/CD on the order of
3.5%. The investigated concept of variable-cant-angle winglets
appears to be a promising alternative for improving the aerodynamic
efficiency of aircraft.
Abstract: This work is focused on the study of valuation of
recycled concrete aggregates, by measuring certain properties of
concrete in the fresh and hardened state. In this study, rheological
tests and physic-mechanical characterization on concretes and
mortars were conducted with recycled concrete whose geometric
properties were identified aggregates. Mortars were elaborated with
recycled fine aggregate (0/5mm) and concretes were manufactured
using recycled coarse aggregates (5/12.5 mm and 12.5/20 mm). First,
a study of the mortars was conducted to determine the effectiveness
of polycarboxylate superplasticizer on the workability of these and
their action deflocculating of the recycled sand. The rheological
behavior of mortars based on fine aggregate recycled was
characterized. The results confirm that the mortars composed of
different fractions of recycled sand (0 /5) have a better mechanical
properties (compressive and flexural strength) compared to normal
mortar. Also, the mechanical strengths of concretes made with
recycled aggregates (5/12.5 mm and 12.5/20 mm), are comparable to
those of conventional concrete with conventional aggregates,
provided that the implementation can be improved by the addition of
a superplasticizer.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: Musculoskeletal injuries in school children could be
reduced improving trunk strength and hamstring flexibility. Low
levels of trunk muscle strength and hamstring flexibility may result in
acute and musculoskeletal chronic diseases. The Pilates Method can
be appropriate to improve these physical condition attributes and has
been rarely employed by this social group. On the other hand, it has
been shown that trunk strength and flexibility are different between
genders, but there is no evidence about the effect of exercise
programs designed to improve both items in school children.
Therefore the objective of this study was to measure the effect of a
six-week Pilates-based exercise program in 14 year old school
children trunk strength and hamstring flexibility, establishing
differences in gender. The sample was composed of 57 students
divided into experimental group (EG; n=30) and control group (CG;
n=27). Bench Trunk Curl test (BTC), Sörensen test and Toe-touch
test (TT) were used to measure dynamic muscular resistance in trunk
flexion, isometric strength in trunk extension and hamstring
flexibility, respectively. EG utilized the Pilates exercise program
during six-weeks (2 days/week, 55minutes/session). After this period
of training, EG improved trunk strength and hamstring flexibility
significantly but there were no significant differences within CG.
Although boys were better in BTC test and girls were better in TT
test, there were no significant differences between them.
Abstract: The main objective of the study is focused in
producing slag based geopolymer concrete obtained with the addition
of alkali activator. Test results indicated that the reaction of silicates
in slag is based on the reaction potential of sodium hydroxide and the
formation of alumino-silicates. The study also comprises on the
evaluation of the efficiency of polymer reaction in terms of the
strength gain properties for different geopolymer mixtures.
Geopolymer mixture proportions were designed for different binder
to total aggregate ratio (0.3 & 0.45) and fine to coarse aggregate ratio
(0.4 & 0.8). Geopolymer concrete specimens casted with normal
curing conditions reported a maximum 28 days compressive strength
of 54.75 MPa. The addition of glued steel fibres at 1.0% Vf in
geopolymer concrete showed reasonable improvements on the
compressive strength, split tensile strength and flexural properties of
different geopolymer mixtures. Further, comparative assessment was
made for different geopolymer mixtures and the reinforcing effects of
steel fibres were investigated in different concrete matrix.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: The objectives of this study is to investigate the
existence of the sticky cost behavior of firms listed in the Indonesia
Stock Exchange (IDX) and to find evidence on the effects of sticky
operating expenses (SG&A expenses) on profitability of firms. For
the first objective, this study finds that the sticky cost behavior does
exist. For the second objective, this study finds that the stickier the
operating expenses the lesser future profitability of the firms. This
study concludes that sticky cost affects negatively to the performance
and, therefore, firms should include flexibility in designing the cost
structure of their firms.
Abstract: This paper explores the effects of gamification on
lower secondary school students’ motivation and engagement in the
classroom. Two-group posttest-only experimental design were
employed to study the influence of gamification teaching method
(GTM) when compared with conventional teaching method (CTM)
on 60 lower secondary school students. The Student Engagement
Instrument (SEI) and Intrinsic Motivation Inventory (IMI) were used
to assess students’ intrinsic motivation and engagement level towards
the respective teaching method. Finding indicates that students who
completed the GTM lesson were significantly higher in intrinsic
motivation to learn than those from the CTM. Although the result
were insignificant and only marginal difference in the engagement
mean, GTM still show better potential in raising student’s
engagement in class when compared with CTM. This finding proves
that the GTM is likely to solve the current issue of low motivation to
learn and low engagement in class among lower secondary school
students in Malaysia. On the other hand, despite being not significant,
higher mean indicates that CTM positively contribute to higher peer
support for learning and better teacher and student relationship when
compared with GTM. As a conclusion, gamification approach is
flexible and can be adapted into many learning content to enhance the
intrinsic motivation to learn and to some extent, encourage better
student engagement in class.
Abstract: This paper is concerning the issues of behaviour of
lightweight expanded clay aggregates concrete exposed to high
temperature. Lightweight aggregates from expanded clay are
produced by firing of row material up to temperature 1050°C.
Lightweight aggregates have suitable properties in terms of volume
stability, when exposed to temperatures up to 1050°C, which could
indicate their suitability for construction applications with higher risk
of fire. The test samples were exposed to heat by using the standard
temperature-time curve ISO 834. Negative changes in resulting
mechanical properties, such as compressive strength, tensile strength,
and flexural strength were evaluated. Also visual evaluation of the
specimen was performed. On specimen exposed to excessive heat, an
explosive spalling could be observed, due to evaporation of
considerable amount of unbounded water from the inner structure of
the concrete.
Abstract: Advances technology in the field of photogrammetry
replaces analog cameras with reflection on aircraft GPS/IMU system
with a digital aerial camera. In this system, when determining the
position of the camera with the GPS, camera rotations are also
determined by the IMU systems. All around the world, digital aerial
cameras have been used for the photogrammetry applications in the
last ten years. In this way, in terms of the work done in
photogrammetry it is possible to use time effectively, costs to be
reduced to a minimum level, the opportunity to make fast and
accurate.
Geo-referencing techniques that are the cornerstone of the GPS /
INS systems, photogrammetric triangulation of images required for
balancing (interior and exterior orientation) brings flexibility to the
process. Also geo-referencing process; needed in the application of
photogrammetry targets to help to reduce the number of ground
control points. In this study, the use of direct and indirect georeferencing
techniques on the accuracy of the points was investigated
in the production of photogrammetric mapping.
Abstract: Load Forecasting plays a key role in making today's
and future's Smart Energy Grids sustainable and reliable. Accurate
power consumption prediction allows utilities to organize in advance
their resources or to execute Demand Response strategies more
effectively, which enables several features such as higher
sustainability, better quality of service, and affordable electricity
tariffs. It is easy yet effective to apply Load Forecasting at larger
geographic scale, i.e. Smart Micro Grids, wherein the lower available
grid flexibility makes accurate prediction more critical in Demand
Response applications. This paper analyses the application of
short-term load forecasting in a concrete scenario, proposed within the
EU-funded GreenCom project, which collect load data from single
loads and households belonging to a Smart Micro Grid. Three
short-term load forecasting techniques, i.e. linear regression, artificial
neural networks, and radial basis function network, are considered,
compared, and evaluated through absolute forecast errors and training
time. The influence of weather conditions in Load Forecasting is also
evaluated. A new definition of Gain is introduced in this paper, which
innovatively serves as an indicator of short-term prediction
capabilities of time spam consistency. Two models, 24- and
1-hour-ahead forecasting, are built to comprehensively compare these
three techniques.