Abstract: Noise has adverse effect on human health and
comfort. Noise not only cause hearing impairment, but it also acts as
a causal factor for stress and raising systolic pressure. Additionally it
can be a causal factor in work accidents, both by marking hazards
and warning signals and by impeding concentration. Industry
workers also suffer psychological and physical stress as well as
hearing loss due to industrial noise. This paper proposes an approach
to enable engineers to point out quantitatively the noisiest source for
modification, while multiple machines are operating simultaneously.
The model with the point source and spherical radiation in a free field
was adopted to formulate the problem. The procedure works very
well in ideal cases (point source and free field). However, most of the
industrial noise problems are complicated by the fact that the noise is
confined in a room. Reflections from the walls, floor, ceiling, and
equipment in a room create a reverberant sound field that alters the
sound wave characteristics from those for the free field. So the model
was validated for relatively low absorption room at NIT Kurukshetra
Central Workshop. The results of validation pointed out that the
estimated sound power of noise sources under simultaneous
conditions were on lower side, within the error limits 3.56 - 6.35 %.
Thus suggesting the use of this methodology for practical
implementation in industry. To demonstrate the application of the
above analytical procedure for estimating the sound power of noise
sources under simultaneous operating conditions, a manufacturing
facility (Railway Workshop at Yamunanagar, India) having five
sound sources (machines) on its workshop floor is considered in this
study. The findings of the case study had identified the two most
effective candidates (noise sources) for noise control in the Railway
Workshop Yamunanagar, India. The study suggests that the
modification in the design and/or replacement of these two identified
noisiest sources (machine) would be necessary so as to achieve an
effective reduction in noise levels. Further, the estimated data allows
engineers to better understand the noise situations of the workplace
and to revise the map when changes occur in noise level due to a
workplace re-layout.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: The increasing industrialization and motorization of the world has led to a steep rise for the demand of petroleum-based fuels. Petroleum-based fuels are obtained from limited reserves. These finite reserves are highly concentrated in certain regions of the world. Therefore, those countries not having these resources are facing energy/foreign exchange crisis, mainly due to the import of crude petroleum. Hence, it is necessary to look for alternative fuels which can be produced from resources available locally within the country such as alcohol, biodiesel, vegetable oils etc. Biodiesel is a renewable, domestically produced fuel that has been shown to reduce particulate, hydrocarbon, and carbon monoxide emissions from combustion. In the present study an experimental investigation on emission characteristic of a liquid burner system operating on several percentage of biodiesel and gas oil is carried out. Samples of exhaust gas are analysed with Testo 350 Xl. The results show that biodiesel can lower some pollutant such as CO, CO2 and particulate matter emissions while NOx emission would increase in comparison with gas oil. The results indicate there may be benefits to using biodiesel in industrial processes.
Abstract: The data is available in abundance in any business
organization. It includes the records for finance, maintenance,
inventory, progress reports etc. As the time progresses, the data keep
on accumulating and the challenge is to extract the information from
this data bank. Knowledge discovery from these large and complex
databases is the key problem of this era. Data mining and machine
learning techniques are needed which can scale to the size of the
problems and can be customized to the application of business. For
the development of accurate and required information for particular
problem, business analyst needs to develop multidimensional models
which give the reliable information so that they can take right
decision for particular problem. If the multidimensional model does
not possess the advance features, the accuracy cannot be expected.
The present work involves the development of a Multidimensional
data model incorporating advance features. The criterion of
computation is based on the data precision and to include slowly
change time dimension. The final results are displayed in graphical
form.
Abstract: Activity-Based Costing (ABC) represents an
alternative paradigm to traditional cost accounting system and
it often provides more accurate cost information for decision
making such as product pricing, product mix, and make-orbuy
decisions. ABC models the causal relationships between
products and the resources used in their production and traces
the cost of products according to the activities through the use
of appropriate cost drivers. In this paper, the implementation
of the ABC in a manufacturing system is analyzed and a
comparison with the traditional cost based system in terms of
the effects on the product costs are carried out to highlight the
difference between two costing methodologies. By using this
methodology, a valuable insight into the factors that cause the
cost is provided, helping to better manage the activities of the
company.
Abstract: A sequential treatment of ozonation followed by a
Fenton or photo-Fenton process, using black light lamps (365 nm) in
this latter case, has been applied to remove a mixture of
pharmaceutical compounds and the generated by-products both in
ultrapure and secondary treated wastewater. The scientifictechnological
innovation of this study stems from the in situ
generation of hydrogen peroxide from the direct ozonation of
pharmaceuticals, and can later be used in the application of Fenton
and photo-Fenton processes. The compounds selected as models
were sulfamethoxazol and acetaminophen. It should be remarked that
the use of a second process is necessary as a result of the low
mineralization yield reached by the exclusive application of ozone.
Therefore, the influence of the water matrix has been studied in terms
of hydrogen peroxide concentration, individual compound
concentration and total organic carbon removed. Moreover, the
concentration of different iron species in solution has been measured.
Abstract: Unified Modeling Language (UML) extensions for real time embedded systems (RTES) co-design, are taking a growing interest by a great number of industrial and research communities. The extension mechanism is provided by UML profiles for RTES. It aims at improving an easily-understood method of system design for non-experts. On the other hand, one of the key items of the co- design methods is the Hardware/Software partitioning and scheduling tasks. Indeed, it is mandatory to define where and when tasks are implemented and run. Unfortunately the main goals of co-design are not included in the usual practice of UML profiles. So, there exists a need for mapping used models to an execution platform for both schedulability test and HW/SW partitioning. In the present work, test schedulability and design space exploration are performed at an early stage. The proposed approach adopts Model Driven Engineering MDE. It starts from UML specification annotated with the recent profile for the Modeling and Analysis of Real Time Embedded systems MARTE. Following refinement strategy, transformation rules allow to find a feasible schedule that satisfies timing constraints and to define where tasks will be implemented. The overall approach is experimented for the design of a football player robot application.
Abstract: Timing driven physical design, synthesis, and
optimization tools need efficient closed-form delay models for
estimating the delay associated with each net in an integrated circuit
(IC) design. The total number of nets in a modern IC design has
increased dramatically and exceeded millions. Therefore efficient
modeling of interconnection is needed for high speed IC-s. This
paper presents closed–form expressions for RC and RLC
interconnection trees in current mode signaling, which can be
implemented in VLSI design tool. These analytical model
expressions can be used for accurate calculation of delay after the
design clock tree has been laid out and the design is fully routed.
Evaluation of these analytical models is several orders of magnitude
faster than simulation using SPICE.
Abstract: The strong international competition as the factor of rising economic development efficiency should not turn into destructive force for models of social orientation. What result Europe received from the accelerated integration without a long transition period of the accepted countries. Correlative relationship between the research and development expenditure and labor productivity, inflation and the rate economy's growth of the USA and the euro zone, employment and gross value added between Old and New Europe is analyzed in this article. The article estimates the differences in economic growth of Old and New Europe. Correlation rate between cycles of the euro area and the countries of Central and the Eastern Europe very much differs, though some of these countries have high correlation as members of the Economic and Monetary Union. Besides, the majority of the countries of Central and the Eastern Europe does not correspond to criteria of an optimum currency area.
Abstract: Mathematical models of dynamics employing exterior calculus are mathematical representations of the same unifying principle; namely, the description of a dynamic system with a characteristic differential one-form on an odd-dimensional differentiable manifold leads, by analysis with exterior calculus, to a set of differential equations and a characteristic tangent vector (vortex vector) which define transformations of the system. Using this principle, a mathematical model for economic growth is constructed by proposing a characteristic differential one-form for economic growth dynamics (analogous to the action in Hamiltonian dynamics), then generating a pair of characteristic differential equations and solving these equations for the rate of economic growth as a function of labor and capital. By contracting the characteristic differential one-form with the vortex vector, the Lagrangian for economic growth dynamics is obtained.
Abstract: The mechanism of abiotic stress tolerance is crucial
for plants to survive in harsh condition and the knowledge of this
mechanism can be use to solve the problem of declining productivity
of plants or crops around the world. However in-depth description is
still unclear and it is argued, in particular that there is a relationship
between high salinity tolerance and the ability to tolerate high light
condition. In this study, Dunaliella salina, which can withstand high
salt was used as a model. Chlorophyll fluorometer for nonphotochemical
quenching (NPQ) measurement and high-performance
liquid chromatography for pigment determination was used. The
results show that NPQ value and the amount of pigment were
increased along with the levels of salinity. However, it establish a
clear relationship between high salt and high light but the further
study to optimized the solutions mentioned above is still required.
Abstract: Plasma Wind Tunnels (PWT) are extensively used for screening and qualification of re-entry Thermel Protection System (TPS) materials. Proper design of a supersonic diffuser for plasma wind tunnel is of importance for achieving good pressurerecovery (thereby reducing vacuum pumping requirement & run time costs) and isolating downstream stream fluctuations from propagating costs) and isolating downstream stream fluctuationnts the details of a rapid design methodology successfully employed for designing supersonic diffuser for high power (several megawatts)plasma wind tunnels and numerical performance analysis of a diffuser configuration designed for one megawatt power rated plasma wind tunnel(enthalpy ~ 30 MJ/kg) using FLUENT 6.3® solver for different diffuser operating sub-atmospheric back-pressures.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: This paper presents a novel approach to finding a
priori interesting regions in mammograms. In order to delineate those
regions of interest (ROI-s) in mammograms, which appear to be
prominent, a topographic representation called the iso-level contour
map consisting of iso-level contours at multiple intensity levels and
region segmentation based-thresholding have been proposed. The
simulation results indicate that the computed boundary gives the
detection rate of 99.5% accuracy.
Abstract: Forty-five dairy cows were used to compare the
enzyme activity of alkaline phosphatase (ALP), lactate
dehydrogenase (LDH), α -amylase in the cervical mucus of cows
during spontaneous and induced estrus using progestagen or PGF2 α
and to determine whether these enzymes affect the fertility in cows
with induced estrus, at the time of Al. The animals were assigned to 3
groups (no treatment, a Crestar® for 12 days, a double im injection of
PGF2 α). The cows were artificially inseminated (AI). Cervical
mucus samples were collected from all cows 3 to 5 min before the
AI. The results are summarized as follows: ALP and α -amylase
activity for spontaneous estrus were similar to those for induced
estrus (P>0.05) . LDH activity levels during spontaneous and PGF2 α
induced estrus was significantly lower (P < 0.001) than that in
progestagene induced estrus groups. While no difference was found
between the first and the third groups. Our result showed a significant
difference in LDH activity levels between cows conceived with 2 or
more AI and those conceived with 1 AI. The result of this study
showed that the enzyme activity in cervical mucus is helpful for
detection of ovulation and time of AI.
Abstract: This research work takes a different approach in
the discussion of urban form impacts on transport planning and
auto dependency. Concentrated density represented by effective
density explains auto dependency better than the conventional
density and it is proved to be a realistic density representative for
the urban transportation analysis. Model analysis reveals that
effective density is influenced by the shopping accessibility
index as well as job density factor. It is also combined with the
job access variable to classify four levels of Transport Activity
Centers (TACs) in Okinawa, Japan. Trip attraction capacity and
levels of the newly classified TACs was found agreeable with the
amount of daily trips attracted to each center. The trip attraction
data set was drawn from a 2007 Okinawa personal trip survey.
This research suggests a planning methodology which guides
logical transport supply routes and concentrated local
development schemes.
Abstract: In order to reduce cost, increase quality, and for
timely supplying production systems has considerably taken the
advantages of supply chain management and these advantages are
also competitive. Selection of appropriate supplier has an important
role in improvement and efficiency of systems.
The models of supplier selection which have already been used by
researchers have considered selection one or more suppliers from
potential suppliers but in this paper selecting one supplier as partner
from one supplier that have minimum one period supplying to buyer
is considered.
This paper presents a conceptual model for partner selection and
application of Degree of Adoptive (DOA) model for final selection.
The attributes weight in this model is prepared through AHP
model. After making the descriptive model, determining the
attributes and measuring the parameters of the adaptive is examined
in an auto industry of Iran(Zagross Khodro co.) and results are
presented.
Abstract: Data mining (DM) is the process of finding and extracting frequent patterns that can describe the data, or predict unknown or future values. These goals are achieved by using various learning algorithms. Each algorithm may produce a mining result completely different from the others. Some algorithms may find millions of patterns. It is thus the difficult job for data analysts to select appropriate models and interpret the discovered knowledge. In this paper, we describe a framework of an intelligent and complete data mining system called SUT-Miner. Our system is comprised of a full complement of major DM algorithms, pre-DM and post-DM functionalities. It is the post-DM packages that ease the DM deployment for business intelligence applications.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.