Abstract: In this paper, a novel Linear Feedback Shift Register
(LFSR) with Look Ahead Clock Gating (LACG) technique is
presented to reduce the power consumption in modern processors
and System-on-Chip. Clock gating is a predominant technique used
to reduce unwanted switching of clock signals. Several clock gating
techniques to reduce the dynamic power have been developed, of
which LACG is predominant. LACG computes the clock enabling
signals of each flip-flop (FF) one cycle ahead of time, based on the
present cycle data of the flip-flops on which it depends. It overcomes
the timing problems in the existing clock gating methods like datadriven
clock gating and Auto-Gated flip-flops (AGFF) by allotting a
full clock cycle for the determination of the clock enabling signals.
Further to reduce the power consumption in LACG technique, FFs
can be grouped so that they share a common clock enabling signal.
Simulation results show that the novel grouped LFSR with LACG
achieves 15.03% power savings than conventional LFSR with LACG
and 44.87% than data-driven clock gating.
Abstract: Increasingly complex modern power systems require
stability, especially for transient and small disturbances. Transient
stability plays a major role in stability during fault and large
disturbance. This paper compares a power system stabilizer (PSS)
and static Var compensator (SVC) to improve damping oscillation
and enhance transient stability. The effectiveness of a PSS connected
to the exciter and/or governor in damping electromechanical
oscillations of isolated synchronous generator was tested. The SVC
device is a member of the shunt FACTS (flexible alternating current
transmission system) family, utilized in power transmission systems.
The designed model was tested with a multi-machine system
consisting of four machines six bus, using MATLAB/SIMULINK
software. The results obtained indicate that SVC solutions are better
than PSS.
Abstract: Introduction: The process to build a better safety
culture, methods of error analysis, and preventive measures, starts
with an understanding of the effects when human factors engineering
refer to remote microscopic diagnosis in surgery and specially in
organ transplantation for the remote evaluation of the grafts. It has
been estimated that even in well-organized transplant systems an
average of 8% to 14% of the grafts (G) that arrive at the recipient
hospitals may be considered as diseased, injured, damaged or
improper for transplantation. Digital microscopy adds information on
a microscopic level about the grafts in Organ Transplant (OT), and
may lead to a change in their management. Such a method will
reduce the possibility that a diseased G, will arrive at the recipient
hospital for implantation. Aim: Ergonomics of Digital Microscopy
(DM) based on virtual slides, on Telemedicine Systems (TS) for
Tele-Pathological (TPE) evaluation of the grafts (G) in organ
transplantation (OT). Material and Methods: By experimental
simulation, the ergonomics of DM for microscopic TPE of Renal
Graft (RG), Liver Graft (LG) and Pancreatic Graft (PG) tissues is
analyzed. In fact, this corresponded to the ergonomics of digital
microscopy for TPE in OT by applying Virtual Slide (VS) system for
graft tissue image capture, for remote diagnoses of possible
microscopic inflammatory and/or neoplastic lesions. Experimentation
included: a. Development of an OTE-TS similar Experimental
Telemedicine System (Exp.-TS), b. Simulation of the integration of
TS with the VS based microscopic TPE of RG, LG and PG applying
DM. Simulation of the DM based TPE was performed by 2
specialists on a total of 238 human Renal Graft (RG), 172 Liver Graft
(LG) and 108 Pancreatic Graft (PG) tissues digital microscopic
images for inflammatory and neoplastic lesions on four electronic
spaces of the four used TS. Results: Statistical analysis of specialist‘s
answers about the ability to diagnose accurately the diseased RG, LG
and PG tissues on the electronic space among four TS (A,B,C,D)
showed that DM on TS for TPE in OT is elaborated perfectly on the
ES of a Desktop, followed by the ES of the applied Exp.-TS. Tablet
and Mobile-Phone ES seem significantly risky for the application of
DM in OT (p
Abstract: Background: To improve the delivery of paediatric
healthcare in low resource settings, Community Health Workers
(CHW) have been provided with a paper-based set of protocols
known as Community Case Management (CCM). Yet research has
shown that CHW adherence to CCM guidelines is poor, ultimately
impacting health service delivery. Digitising the CCM guidelines via
mobile technology is argued in extant literature to improve CHW
adherence. However, little research exist which outlines how (a) this
process can be digitised and (b) adherence could be improved as a
result. Aim: To explore how an electronic mobile version of CCM
(eCCM) can overcome issues associated with the paper-based CCM
protocol (inadequate adherence to guidelines) vis-à-vis service
blueprinting. This service blueprint will outline how (a) the CCM
process can be digitised using mobile Clinical Decision Support
Systems software to support clinical decision-making and (b)
adherence can be improved as a result. Method: Development of a
single service blueprint for a standalone application which visually
depicts the service processes (eCCM) when supporting the CHWs,
using an application known as Supporting LIFE (SL eCCM app) as
an exemplar. Results: A service blueprint is developed which
illustrates how the SL eCCM app can be utilised by CHWs to assist
with the delivery of healthcare services to children. Leveraging
smartphone technologies can (a) provide CHWs with just-in-time
data to assist with their decision making at the point-of-care and (b)
improve CHW adherence to CCM guidelines. Conclusions: The
development of the eCCM opens up opportunities for the CHWs to
leverage the inherent benefit of mobile devices to assist them with
health service delivery in rural settings. To ensure that benefits are
achieved, it is imperative to comprehend the functionality and form
of the eCCM service process. By creating such a service blueprint for
an eCCM approach, CHWs are provided with a clear picture
regarding the role of the eCCM solution, often resulting in buy-in
from the end-users.
Abstract: Temperature regulating system by gaseous nitrogen is
of importance to the space environment simulator, which keeps the
shrouds in the temperature range from -150°C to +150°C. Liquid
nitrogen spray equipment is one of the most critical parts in the
temperature regulating system by gaseous nitrogen. Y type jet
atomizer and internal mixing atomizer of the liquid nitrogen spray
equipment are studied in this paper, 2D/3D atomizer model was
established and grid division was conducted respectively by the
software of Catia and ICEM. Based on the above preparation,
numerical simulation on the spraying process of the atomizer by
FLUENT is performed. Using air and water as the medium,
comparison between the tests and numerical simulation was conducted
and the results of two ways match well. Hence, it can be conclude that
this atomizer model can be applied in the numerical simulation of
liquid nitrogen spray equipment.
Abstract: Cancer is still one of the serious diseases threatening
the lives of human beings. How to have an early diagnosis and
effective treatment for tumors is a very important issue. The animal
carcinoma model can provide a simulation tool for the studies of
pathogenesis, biological characteristics, and therapeutic effects.
Recently, drug delivery systems have been rapidly developed to
effectively improve the therapeutic effects. Liposome plays an
increasingly important role in clinical diagnosis and therapy for
delivering a pharmaceutic or contrast agent to the targeted sites.
Liposome can be absorbed and excreted by the human body, and is
well known that no harm to the human body. This study aimed to
compare the therapeutic effects between encapsulated (doxorubicin
liposomal, Lipodox) and un-encapsulated (doxorubicin, Dox)
anti-tumor drugs using magnetic resonance imaging (MRI).
Twenty-four New Zealand rabbits implanted with VX2 carcinoma at
left thighs were classified into three groups: control group (untreated),
Dox-treated group, and LipoDox-treated group, 8 rabbits for each
group. MRI scans were performed three days after tumor implantation.
A 1.5T GE Signa HDxt whole body MRI scanner with a high
resolution knee coil was used in this study. After a 3-plane localizer
scan was performed, three-dimensional (3D) fast spin echo (FSE)
T2-weighted Images (T2WI) was used for tumor volumetric
quantification. Afterwards, two-dimensional (2D) spoiled gradient
recalled echo (SPGR) dynamic contrast-enhanced (DCE) MRI was
used for tumor perfusion evaluation. DCE-MRI was designed to
acquire four baseline images, followed by contrast agent Gd-DOTA
injection through the ear vein of rabbit. A series of 32 images were
acquired to observe the signals change over time in the tumor and
muscle. The MRI scanning was scheduled on a weekly basis for a
period of four weeks to observe the tumor progression longitudinally.
The Dox and LipoDox treatments were prescribed 3 times in the first
week immediately after the first MRI scan; i.e. 3 days after VX2 tumor
implantation. ImageJ was used to quantitate tumor volume and time
course signal enhancement on DCE images. The changes of tumor size
showed that the growth of VX2 tumors was effectively inhibited for
both LipoDox-treated and Dox-treated groups. Furthermore, the tumor
volume of LipoDox-treated group was significantly lower than that of
Dox-treated group, which implies that LipoDox has better therapeutic effect than Dox. The signal intensity of LipoDox-treated group is
significantly lower than that of the other two groups, which implies
that targeted therapeutic drug remained in the tumor tissue. This study
provides a radiation-free and non-invasive MRI method for
therapeutic monitoring of targeted liposome on an animal tumor
model.
Abstract: A growing demand is felt today for realistic 3D
models enabling the cognition and popularization of historical-artistic
heritage. Evaluation and preservation of Cultural Heritage is
inextricably connected with the innovative processes of gaining,
managing, and using knowledge. The development and perfecting of
techniques for acquiring and elaborating photorealistic 3D models,
made them pivotal elements for popularizing information of objects
on the scale of architectonic structures.
Abstract: The garment manufacturing industry involves
sequential processes that are subjected to uncontrollable variations.
The industry depends on the skill of labour in handling the varieties
of fabrics and accessories, machines, as well as complicated sewing
operation. Due to these reasons, garment manufacturers have created
systems to monitor and to control the quality of the products on a
regular basis by conducting quality approaches to minimize variation.
With that, the aim of this research has been to ascertain the quality
approaches deployed by Malaysian garment manufacturers in three
key areas - quality systems and tools; quality control and types of
inspection; as well as sampling procedures chosen for garment
inspection. Besides, the focus of this research was to distinguish the
quality approaches adopted by companies that supplied finished
garments to both domestic and international markets. Feedback from
each company representative has been obtained via online survey,
which comprised of five sections and 44 questions on the
organizational profile and the quality approaches employed in the
garment industry. As a result, the response rate was 31%. The results
revealed that almost all companies have established their own
mechanism of process control by conducting a series of quality
inspections for daily production, either it was formally set up or
otherwise. In addition, quality inspection has been the predominant
quality control activity in the garment manufacturing, while the level
of complexity of these activities was substantially dictated by the
customers. Moreover, AQL-based sampling was utilized by
companies dealing with exports, whilst almost all the companies that
only concentrated on the domestic market were comfortable using
their own sampling procedures for garment inspection. Hence, this
research has provided insights into the implementation of a number
of quality approaches that were perceived as important and useful in
the garment manufacturing sector, which is truly labour-intensive.
Abstract: The steady flow of a second order fluid through
constricted tube with slip velocity at wall is modeled and analyzed
theoretically. The governing equations are simplified by implying no
slip in radial direction. Based on Karman Pohlhausen procedure
polynomial solution for axial velocity profile is presented.
Expressions for pressure gradient, shear stress, separation and
reattachment points, and radial velocity are also calculated. The
effect of slip and no slip velocity on magnitude velocity, shear stress,
and pressure gradient are discussed and depicted graphically. It is
noted that when Reynolds number increases magnitude velocity of
the fluid decreases in both slip and no slip conditions. It is also found
that the wall shear stress, separation, and reattachment points are
strongly affected by Reynolds number.
Abstract: The paper aims at investigating the effect of number
of story on different structural components of reinforced concrete
building due to gravity and lateral loading. For the study, three
building models having same building plan of three, six and nine
stories are analyzed and designed using software package. All the
buildings are residential and are located in Dhaka city of Bangladesh.
Lateral load including wind and earthquake loading are applied to the
building along both longitudinal and transverse direction as per
Bangladesh National Building Code (BNBC, 2006). Equivalent static
force method is followed for the applied seismic loading. The present
study investigates as well as compares mainly total steel requirement
in different structural components for those buildings. It has been
found that total longitudinal steel requirement for beams at each floor
is 48.57% for three storied building, 61.36% for six storied building
when the total percentage is taken as 100% in case of nine storied
building. For an exterior column, the steel ratio is 2.1%, 3.06%,
4.55% for three, six and nine storied building respectively for the first
three floors. In addition, it has been noted that total weight of
longitudinal reinforcement of an interior column is 14.02 % for threestoried
building and 43.12% for six storied building when the total
reinforcement is considered 100% for nine storied building for the
first three floors.
Abstract: Adequate and reliable estimates of aquifer parameters
are of utmost importance for proper management of vital
groundwater resources. At present scenario, the ground water is
polluted because of industrial waste disposed over the land and the
contaminants are transported in the aquifer from one area to another
area, which is depending on the characteristics of the aquifer and
contaminants. To know the contaminant transport, the accurate
estimation of aquifer properties is highly needed. Conventionally,
these properties are estimated through pumping tests carried out on
water wells. The occurrence and movement of ground water in the
aquifer are characteristically defined by the aquifer parameters. The
pumping (aquifer) test is the standard technique for estimating
various hydraulic properties of aquifer systems, viz., transmissivity
(T), hydraulic conductivity (K), storage coefficient (S) etc., for which
the graphical method is widely used. The study area for conducting
pumping test is Pydibheemavaram Industrial area near the coastal
belt of Srikulam, AP, India. The main objective of the present work is
to estimate the aquifer properties for developing contaminant
transport model for the study area.
Abstract: One of the challenges that higher education faces is to
find how to approach the sustainability in an inclusive way to the
student within all the different academic areas, how to move the
sustainable development from the abstract field to the operational
field. This research comes from the ecoliteracy and the pedagogical
praxis as tools for rebuilding the teaching processes inside of
universities. The purpose is to determine and describe which are the
factors involved in the process of learning particularly in the
Greenhouse-School Siembra UV. In the Greenhouse-School Siembra UV, of the University of
Veracruz, are cultivated vegetables, medicinal plants and small
cornfields under the usage of eco-technologies such as hydroponics,
Wickingbed and Hugelkultur, which main purpose is the saving of
space, labor and natural resources, as well as function as agricultural
production alternatives in the urban and periurban zones. The sample was formed with students from different academic
areas and who are actively involved in the greenhouse, as well as
institutes from the University of Veracruz and governmental and nongovernmental
departments. This project comes from a pedagogic praxis approach, from filling
the needs that the different professional profiles of the university
students have. All this with the purpose of generate a pragmatic
dialogue with the sustainability. It also comes from the necessity to
understand the factors that intervene in the students’ praxis. In this
manner is how the students are the fundamental unit in the sphere of
sustainability. As a result, it is observed that those University of Veracruz
students who are involved in the Greenhouse-school, Siembra UV,
have enriched in different levels the sense of urban and periurban
agriculture because of the diverse academic approaches they have
and the interaction between them. It is concluded that the ecotechnologies
act as fundamental tools for ecoliteracy in society,
where it is strengthen the nutritional and food security from a
sustainable development approach.
Abstract: The goal of this paper is proposing a supply chain
value dashboard in home appliance manufacturing firms to create
more value for all stakeholders via balanced scorecard approach.
Balanced scorecard is an effective approach that managers have used
to evaluate supply chain performance in many fields but there is a
lack of enough attention to all supply chain stakeholders, improving
value creation and, defining correlation between value indicators and
performance measuring quantitatively. In this research the key
stakeholders in home appliance supply chain, value indicators with
respect to create more value for stakeholders and the most important
metrics to evaluate supply chain value performance based on
balanced scorecard approach have been selected via literature review.
The most important indicators based on expert’s judgment acquired
by in survey focused on creating more value for. Structural equation
modelling has been used to disclose relations between value
indicators and balanced scorecard metrics. The important result of
this research is identifying effective value dashboard to create more
value for all stakeholders in supply chain via balanced scorecard
approach and based on an empirical study covering ten home
appliance manufacturing firms in Iran. Home appliance
manufacturing firms can increase their stakeholder's satisfaction by
using this value dashboard.
Abstract: Adoption of Information Systems (IS) is receiving
increasing attention such that its implications have been closely
monitored and studied by the IS management community, industry
and professional gatekeepers. Building on previous research
regarding the adoption of technology, this paper develops and
validates an integrated model of the adoption of mobile banking. The
model originates from the Technology Acceptance Model (TAM) and
the Theory of Planned Behaviour (TPB). This paper intends to offer a
preliminary scrutiny of the antecedents of the adoption of mobile
banking services in the context of a developing country. Data was
collected from Pakistan. The findings showed that an integrated TAM
and TPB model greatly explains the adoption intention of mobile
banking; and perceived behavioural control and its antecedents play a
significant role in predicting adoption Theoretical and managerial
implications of findings are presented and discussed.
Abstract: To study the dynamic mechanics response of asphalt
pavement under the temperature load and vehicle loading, asphalt
pavement was regarded as multilayered elastic half-space system, and
theory analysis was conducted by regarding dynamic modulus of
asphalt mixture as the parameter. Firstly, based on the dynamic
modulus test of asphalt mixture, function relationship between the
dynamic modulus of representative asphalt mixture and temperature
was obtained. In addition, the analytical solution for thermal stress in
single layer was derived by using Laplace integral transformation and
Hankel integral transformation respectively by using thermal
equations of equilibrium. The analytical solution of calculation model
of thermal stress in asphalt pavement was derived by transfer matrix
of thermal stress in multilayer elastic system. Finally, the variation of
thermal stress in pavement structure was analyzed. The result shows
that there is obvious difference between the thermal stress based on
dynamic modulus and the solution based on static modulus. So the
dynamic change of parameter in asphalt mixture should be taken into
consideration when theoretical analysis is taken out.
Abstract: Manufacturing tolerancing is intended to determine
the intermediate geometrical and dimensional states of the part during
its manufacturing process. These manufacturing dimensions also
serve to satisfy not only the functional requirements given in the
definition drawing, but also the manufacturing constraints, for
example geometrical defects of the machine, vibration and the wear
of the cutting tool. The choice of positioning has an important influence on the cost
and quality of manufacture. To avoid this problem, a two-step
approach has been developed. The first step is dedicated to the
determination of the optimum position. As for the second step, a
study was carried out for the tightening effect on the tolerance
interval.
Abstract: In this paper, we describe an application for face
recognition. Many studies have used local descriptors to characterize
a face, the performance of these local descriptors remain low by
global descriptors (working on the entire image). The application of
local descriptors (cutting image into blocks) must be able to store
both the advantages of global and local methods in the Discrete
Cosine Transform (DCT) domain. This system uses neural network
techniques. The letter method provides a good compromise between
the two approaches in terms of simplifying of calculation and
classifying performance. Finally, we compare our results with those
obtained from other local and global conventional approaches.
Abstract: The traditional rhythms of the West African country
of Guinea have played a centuries-long role in defining the different
people groups that make up the country. Throughout their history,
before and since colonization by the French, the different ethnicities
have used their traditional music as a distinct part of their historical
identities. That is starting to change. Guinea is an impoverished
nation created in the early twentieth-century with little regard for the
history and cultures of the people who were included. The traditional
rhythms of the different people groups and their heritages have
remained. Fifteen individual traditional Guinean rhythms were
chosen to represent popular rhythms from the four geographical
regions of Guinea. Each rhythm was traced back to its native village
and video recorded on-site by as many different local performing
groups as could be located. The cyclical patterns rhythms were
transcribed via a circular, spatial design and then copied into a box
notation system where sounds happening at the same time could be
studied. These rhythms were analyzed for their consistency-overperformance
in a Fundamental Rhythm Pattern analysis so rhythms
could be compared for how they are changing through different
performances. The analysis showed that the traditional rhythm
performances of the Middle and Forest Guinea regions were the most
cohesive and showed the least evidence of change between
performances. The role of music in each of these regions is both
limited and focused. The Coastal and High Guinea regions have
much in common historically through their ethnic history and
modern-day trade connections, but the rhythm performances seem to
be less consistent and demonstrate more changes in how they are
performed today. In each of these regions the role and usage of music
is much freer and wide-spread. In spite of advances being made as a
country, different ethnic groups still frequently only respond and
participate (dance and sing) to the music of their native ethnicity.
There is some evidence that this self-imposed musical barrier is
beginning to change and evolve, partially through the development of
better roads, more access to electricity and technology, the nationwide
Ebola health crisis, and a growing self-identification as a
unified nation.
Abstract: Cryosorption pumps are considered safe, quiet, and
ultra-high vacuum production pumps which have their application
from Semiconductor industries to ITER [International Thermonuclear
Experimental Reactor] units. The principle of physisorption of gases
over highly porous materials like activated charcoal at cryogenic
temperatures (below -1500°C) is involved in determining the
pumping speed of gases like Helium, Hydrogen, Argon, and
Nitrogen. This paper aims at providing detailed overview of
development of Cryosorption pump and characterization of different
activated charcoal materials that optimizes the performance of the
pump. Different grades of charcoal were tested in order to determine
the pumping speed of the pump and were compared with
commercially available Varian cryopanel. The results for bare panel,
bare panel with adhesive, cryopanel with pellets, and cryopanel with
granules were obtained and compared. The comparison showed that
cryopanel adhered with small granules gave better pumping speeds
than large sized pellets.
Abstract: In this paper, we present an application of Riemannian
geometry for processing non-Euclidean image data. We consider the
image as residing in a Riemannian manifold, for developing a new
method to brain edge detection and brain extraction. Automating this
process is a challenge due to the high diversity in appearance brain
tissue, among different patients and sequences. The main contribution, in this paper, is the use of an edge-based
anisotropic diffusion tensor for the segmentation task by integrating
both image edge geometry and Riemannian manifold (geodesic,
metric tensor) to regularize the convergence contour and extract
complex anatomical structures. We check the accuracy of the
segmentation results on simulated brain MRI scans of single
T1-weighted, T2-weighted and Proton Density sequences. We
validate our approach using two different databases: BrainWeb
database, and MRI Multiple sclerosis Database (MRI MS DB). We
have compared, qualitatively and quantitatively, our approach with
the well-known brain extraction algorithms. We show that using
a Riemannian manifolds to medical image analysis improves the
efficient results to brain extraction, in real time, outperforming the
results of the standard techniques.