Abstract: In the present study, the kinetics of thermal
degradation of a phenolic and lignin reinforced phenolic foams, and
the lignin used as reinforcement were studied and the activation
energies of their degradation processes were obtained by a DAEM
model. The average values for five heating rates of the mean
activation energies obtained were: 99.1, 128.2, and 144.0 kJ.mol-1 for
the phenolic foam; 109.5, 113.3, and 153.0 kJ.mol-1 for the lignin
reinforcement; and 82.1, 106.9, and 124.4 kJ.mol-1 for the lignin
reinforced phenolic foam. The standard deviation ranges calculated
for each sample were 1.27-8.85, 2.22-12.82, and 3.17-8.11 kJ.mol-1
for the phenolic foam, lignin and the reinforced foam, respectively.
The DAEM model showed low mean square errors (
Abstract: This study is about the structural transformations of
aluminium examining with the Dynamic Mechanical Thermal
Analyzer (DMTA). It is a faster and simpler measuring method to
make consequence about the metal’s structural transformations. The
device measures the changing of the mechanical characteristics
depending on the heating rate, and concludes certain transformations.
This measuring method fast and shows clean-cut results comparing
the conventional ways.
Applying polymer measuring devices for metal investigations is
not widespread method. One of the adaptable ways is shown in this
study. The article compares the results of the small specimen test and
the DMTA method, considering the temperature and the forming
dependence of recrystallization temperature.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: By textile science incorporating with electronic
industry, developed textile products start to take part in different
areas such as industry, military, space, medical etc. for health,
protection, defense, communication and automation. Electronic
textiles (e-textiles) are fabrics that contain electronics and
interconnections with them. In this study, two types of base yarns
(cotton and acrylic) and three types of conductive steel yarns with
different linear resistance values (14Ω/m, 30Ω/m, 70Ω/m) were used
to investigate the effect of base yarn type and linear resistance of
conductive yarns on thermal behavior of e-textile structures. Thermal
behavior of samples was examined by thermal camera.
Abstract: In our research we aimed to test a managerial
approach for the fuzzy front end (FFE) of innovation by creating
controlled experiment/ business case in a breakthrough innovation
development. The experiment was in the sport industry and covered
all aspects of the customer discovery stage from ideation to
prototyping followed by patent application. In the paper we describe
and analyze mile stones, tasks, management challenges, decisions
made to create the break through innovation, evaluate overall
managerial efficiency that was at the considered FFE stage.
We set managerial outcome of the FFE stage as a valid product
concept in hand. In our paper we introduce hypothetical construct
“Q-factor” that helps us in the experiment to distinguish quality of
FFE outcomes.
The experiment simulated for entrepreneur the FFE of innovation
and put on his shoulders responsibility for the outcome of valid
product concept. While developing managerial approach to reach the
outcome there was a decision to look on product concept from the
cognitive psychology and cognitive science point of view. This view
helped us to develop the profile of a person whose projection (mental
representation) of a new product could optimize for a manager or
entrepreneur FFE activities. In the experiment this profile was tested
to develop breakthrough innovation for swimmers. Following the
managerial approach the product concept was created to help
swimmers to feel/sense water. The working prototype was developed
to estimate the product concept validity and value added effect for
customers.
Based on feedback from coachers and swimmers there were strong
positive effect that gave high value for customers, and for the
experiment – the valid product concept being developed by proposed
managerial approach for the FFE.
In conclusions there is a suggestion of managerial approach that
was derived from experiment.
Abstract: The performance of box-type solar cookers has been
reported by several researchers but little attention was paid to the
effect of the type of insulation material on the energy and exergy
efficiency of these cookers. This research aimed at evaluating the
energy and exergy efficiencies of the box-type cookers containing
different insulation materials. Energy and exergy efficiencies of five
box-type solar cookers insulated with maize cob, air (control), maize
husk, coconut coir and polyurethane foam respectively were obtained
over a period of three years. The cookers were evaluated using water
heating test procedures in determining the energy and exergy
analysis. The results were subjected to statistical analysis using
ANOVA. The result shows that the average energy input for the five
solar cookers were: 245.5, 252.2, 248.7, 241.5 and 245.5J
respectively while their respective average energy losses were: 201.2,
212.7, 208.4, 189.1 and 199.8J. The average exergy input for five
cookers were: 228.2, 234.4, 231.1, 224.4 and 228.2J respectively
while their respective average exergy losses were: 223.4, 230.6,
226.9, 218.9 and 223.0J. The energy and exergy efficiency was
highest in the cooker with coconut coir (37.35 and 3.90%
respectively) in the first year but was lowest for air (11 and 1.07%
respectively) in the third year. Statistical analysis showed significant
difference between the energy and exergy efficiencies over the years.
These results reiterate the importance of a good insulating material
for a box-type solar cooker.
Abstract: Parabolic solar trough systems have seen limited
deployments in cold northern climates as they are more suitable for
electricity production in southern latitudes. A numerical dynamic
model is developed to simulate troughs installed in cold climates and
validated using a parabolic solar trough facility in Winnipeg. The
model is developed in Simulink and will be utilized to simulate a trigeneration
system for heating, cooling and electricity generation in
remote northern communities. The main objective of this simulation
is to obtain operational data of solar troughs in cold climates and use
the model to determine ways to improve the economics and address
cold weather issues.
In this paper the validated Simulink model is applied to simulate a
solar assisted absorption cooling system along with electricity
generation using Organic Rankine Cycle (ORC) and thermal storage.
A control strategy is employed to distribute the heated oil from solar
collectors among the above three systems considering the
temperature requirements. This modelling provides dynamic
performance results using measured meteorological data recorded
every minute at the solar facility location. The purpose of this
modeling approach is to accurately predict system performance at
each time step considering the solar radiation fluctuations due to
passing clouds. Optimization of the controller in cold temperatures is
another goal of the simulation to for example minimize heat losses in
winter when energy demand is high and solar resources are low.
The solar absorption cooling is modeled to use the generated heat
from the solar trough system and provide cooling in summer for a
greenhouse which is located next to the solar field.
The results of the simulation are presented for a summer day in
Winnipeg which includes comparison of performance parameters of
the absorption cooling and ORC systems at different heat transfer
fluid (HTF) temperatures.
Abstract: Recently, the green architecture becomes a
significant way to a sustainable future. Green building designs
involve finding the balance between comfortable homebuilding and
sustainable environment. Moreover, the utilization of the new
technologies such as artificial intelligence techniques are used to
complement current practices in creating greener structures to keep
the built environment more sustainable. The most common objectives
in green buildings should be designed to minimize the overall impact
of the built environment that effect on ecosystems in general and in
particularly human health and natural environment. This will lead to
protecting occupant health, improving employee productivity,
reducing pollution and sustaining the environmental. In green
building design, multiple parameters which may be interrelated,
contradicting, vague and of qualitative/quantitative nature are
broaden to use. This paper presents a comprehensive critical state- ofart-
review of current practices based on fuzzy and its combination
techniques. Also, presented how green architecture/building can be
improved using the technologies that been used for analysis to seek
optimal green solutions strategies and models to assist in making the
best possible decision out of different alternatives.
Abstract: In this study, the Compressive strength of concretes
made with Ground Granulated Blast furnace Slag (GGBS),
Pulverised Fuel Ash (PFA), Rice Husk Ash (RHA) and Waste Glass
Powder (WGP) after they were exposed 7800C (exposure duration of
around 60 minutes) and then allowed to cool down gradually in the
furnace for about 280 minutes at water binder ratio of 0.50 was
investigated. GGBS, PFA, RHA and WGP were used to replace up to
20% Portland cement in the control concrete. Test for the
determination of workability, compressive strength and tensile
splitting strength of the concretes were carried out and the results
were compared with control concrete. The test results showed that the
compressive strength decreased by an average of around 30% after
the concretes were exposed to the heating and cooling scenario.
Abstract: Hybrid bioreactor having both suspended-growth and
attached-growth bacteria is found a novel and excellent bioreactor
system for treating the municipal wastewater containing inhibitory
substrates too. In this reactor a fraction of substrate is used by
suspended biomass and the remaining by attached biomass resulting
in the competition between the two growths for the substrate. The
combination of suspended and attached growth provides the system
with enhanced biomass concentration and sludge age more than those
in ASP. Similar to attached growth system, the hybrid bioreactor
ensures considerable efficiency for treating toxic and refractory
substances in wastewater. For the process design of hybrid bioreactor
a suitable mathematical model is required. Although various
mathematical models were developed on hybrid bioreactor in due
course of time in earlier research works, none of them was found
having a specific simplified solution of the corresponding models and
without having any drawback. To overcome this drawback authors
already developed a simplified mathematical model for process
design of a hybrid bioreactor. The present paper briefly highlights on
the various aspects of process design of an aerobic hybrid bioreactor
for the treatment of municipal wastewater.
Abstract: The building sector is responsible, in many
industrialized countries, for about 40% of the total energy
requirements, so it seems necessary to devote some efforts in this
area in order to achieve a significant reduction of energy
consumption and of greenhouse gases emissions.
The paper presents a study aiming at providing a design
methodology able to identify the best configuration of the system
building/plant, from a technical, economic and environmentally point
of view.
Normally, the classical approach involves a building's energy
loads analysis under steady state conditions, and subsequent selection
of measures aimed at improving the energy performance, based on
previous experience made by architects and engineers in the design
team. Instead, the proposed approach uses a sequence of two wellknown
scientifically validated calculation methods (TRNSYS and
RETScreen), that allow quite a detailed feasibility analysis.
To assess the validity of the calculation model, an existing,
historical building in Central Italy, that will be the object of
restoration and preservative redevelopment, was selected as a casestudy.
The building is made of a basement and three floors, with a
total floor area of about 3,000 square meters.
The first step has been the determination of the heating and
cooling energy loads of the building in a dynamic regime by means,
which allows simulating the real energy needs of the building in
function of its use. Traditional methodologies, based as they are on
steady-state conditions, cannot faithfully reproduce the effects of
varying climatic conditions and of inertial properties of the structure.
With this model is possible to obtain quite accurate and reliable
results that allow identifying effective combinations building-HVAC
system.
The second step has consisted of using output data obtained as
input to the calculation model, which enables to compare different
system configurations from the energy, environmental and financial
point of view, with an analysis of investment, and operation and
maintenance costs, so allowing determining the economic benefit of
possible interventions.
The classical methodology often leads to the choice of
conventional plant systems, while our calculation model provides a
financial-economic assessment for innovative energy systems and
low environmental impact.
Computational analysis can help in the design phase, particularly
in the case of complex structures with centralized plant systems, by
comparing the data returned by the calculation model for different
design options.
Abstract: In this paper we are presenting some spamming
techniques their behaviour and possible solutions. We have analyzed
how Spammers enters into online social networking sites (OSNSs) to
target them and diverse techniques used by them for this purpose.
Spamming is very common issue in present era of Internet
especially through Online Social Networking Sites (like Facebook,
Twitter, and Google+ etc.). Spam messages keep wasting Internet
bandwidth and the storage space of servers. On social networking
sites; spammers often disguise themselves by creating fake accounts
and hijacking user’s accounts for personal gains. They behave like
normal user and they continue to change their spamming strategy.
Following spamming techniques are discussed in this paper like
clickjacking, social engineered attacks, cross site scripting, URL
shortening, and drive by download. We have used elgg framework
for demonstration of some of spamming threats and respective
implementation of solutions.
Abstract: Carbon Deposits are often occurred inside the
industrial coke oven during coking process. Accumulation of carbon
deposits may cause a big issue, which seriously influences the coking
operation. The carbon is burning off by injecting fresh air through
pipes into coke oven which is an efficient way practically operated in
industries. The burning off carbon deposition in coke oven performed
by Computational Fluid Dynamics (CFD) method has provided an
evaluation of the feasibility study. A three dimensional, transient,
turbulent reacting flow simulation has performed with three different
injecting air flow rate and another kind of injecting configuration. The
result shows that injection higher air flow rate would effectively
reduce the carbon deposits. In the meantime, the opened charging
holes would suck extra oxygen from atmosphere to participate in
reactions. In term of coke oven operating limits, the wall temperatures
are monitored to prevent over-heating of the adiabatic walls during
burn-off process.
Abstract: The characteristics of temperature distribution and
electric field in a natural rubber glove (NRG) using microwave
energy during microwave heating process are investigated
numerically and experimentally. A three-dimensional model of NRG
and microwave oven are considered in this work. The influences of
position, heating time and rotation angle of NRG on temperature
distribution and electric field are presented in details. The coupled
equations of electromagnetic wave propagation and heat transfer are
solved using the finite element method (FEM). The numerical model
is validated with an experimental study at a frequency of 2.45 GHz.
The results show that the numerical results closely match the
experimental results. Furthermore, it is found that the temperature
distribution and electric field increases with increasing heating time.
The hot spot zone appears in NRG at the tip of middle finger while
the maximum temperature occurs in case of rotation angle of NRG =
60 degree. This investigation provides the essential aspects for a
fundamental understanding of heat transport of NRG using
microwave energy in industry.
Abstract: A new concept of response system is proposed for
filling the gap that exists in reducing vulnerability during immediate
response to natural disasters. Real Time Early Response Systems
(RTERSs) incorporate real time information as feedback data for
closing control loop and for generating real time situation assessment.
A review of the state of the art on works that fit the concept of
RTERS is presented, and it is found that they are mainly focused on
manmade disasters. At the same time, in response phase of natural
disaster management many works are involved in creating early
warning systems, but just few efforts have been put on deciding what
to do once an alarm is activated. In this context a RTERS arises as a
useful tool for supporting people in their decision making process
during natural disasters after an event is detected, and also as an
innovative context for applying well-known automation technologies
and automatic control concepts and tools.
Abstract: The main objective of aircraft aerodynamics is to
enhance the aerodynamic characteristics and maneuverability of the
aircraft. This enhancement includes the reduction in drag and stall
phenomenon. The airfoil which contains dimples will have
comparatively less drag than the plain airfoil. Introducing dimples on
the aircraft wing will create turbulence by creating vortices which
delays the boundary layer separation resulting in decrease of pressure
drag and also increase in the angle of stall. In addition, wake
reduction leads to reduction in acoustic emission. The overall
objective of this paper is to improve the aircraft maneuverability by
delaying the flow separation point at stall and thereby reducing the
drag by applying the dimple effect over the aircraft wing. This project
includes both computational and experimental analysis of dimple
effect on aircraft wing, using NACA 0018 airfoil. Dimple shapes of
Semi-sphere, hexagon, cylinder, square are selected for the analysis;
airfoil is tested under the inlet velocity of 30m/s and 60m/s at
different angle of attack (5˚, 10˚, 15˚, 20˚, and 25˚). This analysis
favors the dimple effect by increasing L/D ratio and thereby
providing the maximum aerodynamic efficiency, which provides the
enhanced performance for the aircraft.
Abstract: Anxiety is a common psychological problem and also
implicated as a contributor to many chronic diseases which decreased
quality of life even with pharmacological treatment. At the present
time several yogic practices- meditation, pranayama, and mantra,
etcetera are playing important role in treating physiological and
psychological problems. Hence, the present investigation is aimed to
see the effect of Trataka on the level of anxiety among adolescents.
For the present study, a sample of 30 adolescents belonging to the
age range 20-30 years was selected from Devsanskriti Vishwa
Vidyalaya Haridwar through random sampling. In this investigation,
Sinha’s Comprehensive anxiety test has been used to measure the
level of anxiety. Statistical analysis has been done by using t-test.
Findings of this study reveal that Trataka significantly decreases the
level of anxiety among adolescents.
Abstract: Established objective and subjective preconditions for
entrepreneurship, forming the business organically related whole, are
the necessary condition of successful entrepreneurial activities.
Objective preconditions for entrepreneurship are developed by
market economy that should stimulate entrepreneurship by allowing
the use of economic opportunities for all those who want to do
business in respective field while providing guarantees to all owners
and creating a stable business environment for entrepreneurs.
Subjective preconditions of entrepreneurship are formed primarily by
personal characteristics of the entrepreneur. These are his properties,
abilities, skills, physiological and psychological preconditions which
may be inherited, inborn or sequentially developed and obtained
during his life on the basis of education and influences of
surrounding environment. The paper is dealing with issues of
objective and subjective preconditions for entrepreneurship and
provides their analysis in view of the current situation in Slovakia. It
presents risks of the business environment in Slovakia that the Slovak
managers considered the most significant in 2014 and defines the
dominant attributes of the entrepreneur in the current business
environment in Slovakia.
Abstract: At present, the cascade PID control is widely used to
control the superheating temperature (main steam temperature). As
Main Steam Temperature has the characteristics of large inertia, large
time-delay and time varying, etc., conventional PID control strategy
cannot achieve good control performance. In order to overcome the
bad performance and deficiencies of main steam temperature control
system, Model Free Adaptive Control (MFAC) - P cascade control
system is proposed in this paper. By substituting MFAC in PID of the
main control loop of the main steam temperature control, it can
overcome time delays, non-linearity, disturbance and time variation.
Abstract: Living today in turbulent business environment forces
companies to distinguish from each other, securing sustainable
competitive growth and competitive advantage. The best possible
solution is to invest (effort and financial resources) within
companies’ different practices of human resource management
(HRM), more specifically in employees’ knowledge, skills and
abilities. Applying this approach companies will create enviable level
of human capital securing its economic growth. Employees become
human capital for their employers at the moment when they
contribute with their own knowledge and abilities in creating material
and non-material value of the company. The main aim of this
research is to explore the relations between human capital
investments and business excellence of Croatian companies.
Furthermore, the differences in the level of human capital
investments with regard to several companies’ characteristics (e.g.
size of the company, ownership and type of the industry) are
investigated.