Abstract: Green roof system is considered a relatively new
concept in Malaysia even though it has been implemented widely in
the developed countries. Generally, green roofs provide many
benefits such as enhancing aesthetical quality of the built
environment, reduce urban heat island effect, reduce energy
consumption, improve stormwater attenuation, and reduce noise
pollution. A better understanding on the implementation of green roof
system in Malaysia is crucial, as Malaysia’s climate is different if
compared with the climate in temperate countries where most of the
green roof studies have been conducted. This study has concentrated
on the technical aspect of green roof system which focuses on i) types
of plants and method of planting; ii) engineering design for green
roof system; iii) its hydrological performance on reducing stormwater
runoff; and iv) benefits of green roofs with respect to energy.
Literature review has been conducted to identify the development and
obstacles associated with green roofs systems in Malaysia. The study
had identified the challenges and potentials of green roofs
development in Malaysia. This study also provided the
recommendations on standard design and strategies on the
implementation of green roofs in Malaysia in the near future.
Abstract: This paper describes an ab-initio design, development and calibration results of an Optical Sensor Ground Reaction Force Measurement Platform (OSGRFP) for gait and geriatric studies. The developed system employs an array of FBG sensors to measure the respective ground reaction forces from all three axes (X, Y and Z), which are perpendicular to each other. The novelty of this work is two folded. One is in its uniqueness to resolve the tri axial resultant forces during the stance in to the respective pure axis loads and the other is the applicability of inherently advantageous FBG sensors which are most suitable for biomechanical instrumentation. To validate the response of the FBG sensors installed in OSGRFP and to measure the cross sensitivity of the force applied in other directions, load sensors with indicators are used. Further in this work, relevant mathematical formulations are presented for extracting respective ground reaction forces from wavelength shifts/strain of FBG sensors on the OSGRFP. The result of this device has implications in understanding the foot function, identifying issues in gait cycle and measuring discrepancies between left and right foot. The device also provides a method to quantify and compare relative postural stability of different subjects under test, which has implications in post-surgical rehabilitation, geriatrics and optimizing training protocols for sports personnel.
Abstract: Energy consumption data, in particular those involving
public buildings, are impacted by many factors: the building structure,
climate/environmental parameters, construction, system operating
condition, and user behavior patterns. Traditional methods for data
analysis are insufficient. This paper delves into the data mining
technology to determine its application in the analysis of building
energy consumption data including energy consumption prediction,
fault diagnosis, and optimal operation. Recent literature are reviewed
and summarized, the problems faced by data mining technology in the
area of energy consumption data analysis are enumerated, and research
points for future studies are given.
Abstract: In the deep south of Thailand, checkpoints for people
verification are necessary for the security management of risk zones,
such as official buildings in the conflict area. In this paper, we
propose an automatic checkpoint system that verifies persons using
information from ID cards and facial features. The methods for a
person’s information abstraction and verification are introduced
based on useful information such as ID number and name, extracted
from official cards, and facial images from videos. The proposed
system shows promising results and has a real impact on the local
society.
Abstract: Introduction: To update ourselves and understand the
concept of latest electronic formats available for Health care
providers and how it could be used and developed as per standards.
The idea is to correlate between the patients Manual Medical Records
keeping and maintaining patients Electronic Information in a Health
care setup in this world. Furthermore, this stands with adapting to the
right technology depending upon the organization and improve our
quality and quantity of Healthcare providing skills. Objective: The
concept and theory is to explain the terms of Electronic Medical
Record (EMR), Electronic Health Record (EHR) and Personal Health
Record (PHR) and selecting the best technical among the available
Electronic sources and software before implementing. It is to guide
and make sure the technology used by the end users without any
doubts and difficulties. The idea is to evaluate is to admire the uses
and barriers of EMR-EHR-PHR. Aim and Scope: The target is to
achieve the health care providers like Physicians, Nurses, Therapists,
Medical Bill reimbursements, Insurances and Government to assess
the patient’s information on easy and systematic manner without
diluting the confidentiality of patient’s information. Method: Health
Information Technology can be implemented with the help of
Organisations providing with legal guidelines and help to stand by
the health care provider. The main objective is to select the correct
embedded and affordable database management software and
generating large-scale data. The parallel need is to know how the
latest software available in the market. Conclusion: The question lies
here is implementing the Electronic information system with
healthcare providers and organization. The clinicians are the main
users of the technology and manage us to “go paperless”. The fact is
that day today changing technologically is very sound and up to date.
Basically, the idea is to tell how to store the data electronically safe
and secure. All three exemplifies the fact that an electronic format
has its own benefit as well as barriers.
Abstract: Torrefaction of biomass pellets is considered as a
useful pretreatment technology in order to convert them into a high
quality solid biofuel that is more suitable for pyrolysis, gasification,
combustion, and co-firing applications. In the course of torrefaction,
the temperature varies across the pellet, and therefore chemical
reactions proceed unevenly within the pellet. However, the
uniformity of the thermal distribution along the pellet is generally
assumed. The torrefaction process of a single cylindrical pellet is
modeled here, accounting for heat transfer coupled with chemical
kinetics. The drying sub-model was also introduced. The nonstationary
process of wood pellet decomposition is described by the
system of non-linear partial differential equations over the
temperature and mass. The model captures well the main features of
the experimental data.
Abstract: Motion response of floating structures is of great
concern in marine engineering. Nonlinearity is an inherent property
of any floating bodies subjected to irregular waves. These floating
structures are continuously subjected to environmental loadings from
wave, current, wind etc. This can result in undesirable motions of the
vessel which may challenge the operability. For a floating body to
remain in its position, it should be able to induce a restoring force
when displaced. Mooring is provided to enable this restoring force.
This paper discusses the hydrodynamic performance and motion
characteristics of an 8 point spread mooring system applied to a pipe
laying barge operating in the West African sea. The modelling of the
barge is done using a computer aided-design (CAD) software
RHINOCEROS. Irregular waves are generated using a suitable wave
spectrum. Both frequency domain and time domain analysis is done.
Numerical simulations based on potential theory are carried out to
find the responses and hydrodynamic performance of the barge in
both free floating as well as moored conditions. Initially, potential
flow frequency domain analysis is done to obtain the Response
Amplitude Operator (RAO) which gives an idea about the structural
motion in free floating state. RAOs for different wave headings are
analyzed. In the following step, a time domain analysis is carried out
to obtain the responses of the structure in the moored condition. In
this study, wave induced motions are only taken into consideration.
Wind and current loads are ruled out and shall be included in further
studies. For the current study, 2000 seconds simulation is taken. The
results represent wave induced motion responses, mooring line
tensions and identify critical mooring lines.
Abstract: We have aimed to produce a self-cleaning transparent
polymer coating with polyurethane (PU) matrix as the latter is highly
solvent, chemical and weather resistant having good mechanical
properties. Nano-silica modified by 1H, 1H, 2H, 2Hperflurooctyltriethoxysilane
was incorporated into the PU matrix for
attaining self-cleaning ability through hydrophobicity. The
modification was confirmed by particle size analysis and scanning
electron microscopy (SEM). Thermo-gravimetric (TGA) studies were
carried to ascertain the grafting of silane onto the silica. Several
coating formulations were prepared by varying the silica loading
content and compared to a commercial equivalent. The effect of
dispersion and the morphology of the coated films were assessed by
SEM analysis. All coating standardized tests like solvent resistance,
adhesion, flexibility, acid, alkali, gloss etc. have been performed as
per ASTM standards. Water contact angle studies were conducted to
analyze the hydrophobic character of the coating. In addition, the
coatings were also subjected to salt spray and accelerated weather
testing to analyze the durability of the coating.
Abstract: At the Savonia University of Applied Sciences (UAS),
curriculum and studies have been improved by applying an Open
Innovation Space approach (OIS). It is based on multidisciplinary
action learning. The key elements of OIS-ideology are work-life
orientation, and student-centric communal learning. In this approach,
every participant can learn from each other and innovations will be
created. In this social innovation educational approach, all practices
are carried out in close collaboration with enterprises in real-life
settings, not in classrooms. As an example, in this paper, Savonia
UAS’s Future Food RDI hub (FF) shows how OIS practices are
implemented by providing food product development and consumer
research services for enterprises in close collaboration with
academicians, students and consumers. In particular one example of
OIS experimentation in the field is provided by a consumer research
carried out utilizing verbal analysis protocol combined with audiovisual
observation (VAP-WAVO). In this case, all co-learners were
acting together in supermarket settings to collect the relevant data for
a product development and the marketing department of a company.
The company benefitted from the results obtained, students were
more satisfied with their studies, educators and academicians were
able to obtain good evidence for further collaboration as well as
renewing curriculum contents based on the requirements of working
life. In addition, society will benefit over time as young university
adults find careers more easily through their OIS related food science
studies. Also this knowledge interaction model re-news education
practices and brings working-life closer to educational research
institutes.
Abstract: Pedagogical approaches in Asia nowadays are
imported from the West. In Confucian Heritage Culture (CHC),
however, there is a dichotomy between the perceived benefits of
Western pedagogies and the real classroom practices in Chinese
societies. The success of Hong Kong students in large-scale
international assessments has proved that both the strengths of both
Western pedagogies and CHC educational approaches should be
integrated for the sake of the students. University students aim to equip themselves with employability
skills upon graduation. Formative assessments allow students to
receive detailed, positive, and timely feedback and they can identify
their strengths and weaknesses before they start working. However,
there remains a question of whether university year 1 students who
come from an examination-driven secondary education background
are ready to respond to more formative assessments. The findings show that year 1 students are less concerned about
competition in the university and more open to new teaching
approaches that will allow them to improve as professionals in their
major study areas.
Abstract: Fractal based digital image compression is a specific
technique in the field of color image. The method is best suited for
irregular shape of image like snow bobs, clouds, flame of fire; tree
leaves images, depending on the fact that parts of an image often
resemble with other parts of the same image. This technique has
drawn much attention in recent years because of very high
compression ratio that can be achieved. Hybrid scheme incorporating
fractal compression and speedup techniques have achieved high
compression ratio compared to pure fractal compression. Fractal
image compression is a lossy compression method in which selfsimilarity
nature of an image is used. This technique provides high
compression ratio, less encoding time and fart decoding process. In
this paper, fractal compression with quad tree and DCT is proposed
to compress the color image. The proposed hybrid schemes require
four phases to compress the color image. First: the image is
segmented and Discrete Cosine Transform is applied to each block of
the segmented image. Second: the block values are scanned in a
zigzag manner to prevent zero co-efficient. Third: the resulting image
is partitioned as fractals by quadtree approach. Fourth: the image is
compressed using Run length encoding technique.
Abstract: Myoelectric control system is the fundamental
component of modern prostheses, which uses the myoelectric signals
from an individual’s muscles to control the prosthesis movements.
The surface electromyogram signal (sEMG) being noninvasive has
been used as an input to prostheses controllers for many years.
Recent technological advances has led to the development of
implantable myoelectric sensors which enable the internal
myoelectric signal (MES) to be used as input to these prostheses
controllers. The intramuscular measurement can provide focal
recordings from deep muscles of the forearm and independent signals
relatively free of crosstalk thus allowing for more independent
control sites. However, little work has been done to compare the two
inputs. In this paper we have compared the classification accuracy of
six pattern recognition based myoelectric controllers which use
surface myoelectric signals recorded using untargeted (symmetric)
surface electrode arrays to the same controllers with multichannel
intramuscular myolectric signals from targeted intramuscular
electrodes as inputs. There was no significant enhancement in the
classification accuracy as a result of using the intramuscular EMG
measurement technique when compared to the results acquired using
the surface EMG measurement technique. Impressive classification
accuracy (99%) could be achieved by optimally selecting only five
channels of surface EMG.
Abstract: A 15-storey RC building, studied in this paper, is
representative of modern building type constructed in Madina City in
Saudi Arabia before 10 years ago. These buildings are almost
consisting of reinforced concrete skeleton i.e. columns, beams and
flat slab as well as shear walls in the stairs and elevator areas
arranged in the way to have a resistance system for lateral loads
(wind – earthquake loads). In this study, the dynamic properties of
the 15-storey RC building were identified using ambient motions
recorded at several, spatially-distributed locations within each
building. Three dimensional pushover analysis (Nonlinear static
analysis) was carried out using SAP2000 software incorporating
inelastic material properties for concrete, infill and steel. The effect
of modeling the building with and without infill walls, on the
performance point as well as capacity and demand spectra due to EQ
design spectrum function in Madina area has been investigated. ATC-
40 capacity and demand spectra are utilized to get the modification
factor (R) for the studied building. The purpose of this analysis is to
evaluate the expected performance of structural systems by
estimating, strength and deformation demands in design, and
comparing these demands to available capacities at the performance
levels of interest. The results are summarized and discussed.
Abstract: The beginning of 21st century has witnessed new
advancements in the design and use of new materials for biosensing
applications, from nano to macro, protein to tissue. Traditional
analytical methods lack a complete toolset to describe the
complexities introduced by living systems, pathological relations,
discrete hierarchical materials, cross-phase interactions, and
structure-property dependencies. Materiomics – via systematic
molecular dynamics (MD) simulation – can provide structureprocess-
property relations by using a materials science approach
linking mechanisms across scales and enables oriented biosensor
design. With this approach, DNA biosensors can be utilized to detect
disease biomarkers present in individuals’ breath such as acetone for
diabetes. Our wireless sensor array based on single-stranded DNA
(ssDNA)-decorated single-walled carbon nanotubes (SWNT) has
successfully detected trace amount of various chemicals in vapor
differentiated by pattern recognition. Here, we present how MD
simulation can revolutionize the way of design and screening of DNA
aptamers for targeting biomarkers related to oral diseases and oral
health monitoring. It demonstrates great potential to be utilized to
build a library of DNDA sequences for reliable detection of several
biomarkers of one specific disease, and as well provides a new
methodology of creating, designing, and applying of biosensors.
Abstract: An Energetic and exergetic analysis is conducted on a
Steam Turbine Power Plant of an existing Phosphoric Acid Factory.
The heat recovery systems used in different parts of the plant are also
considered in the analysis. Mass, thermal and exergy balances are
established on the main compounds of the factory. A numerical code
is established using EES software to perform the calculations
required for the thermal and exergy plant analysis. The effects of the
key operating parameters such as steam pressure and temperature,
mass flow rate as well as seawater temperature, on the cycle
performances are investigated. A maximum Exergy Loss Rate of about 72% is obtained for the
melters, followed by the condensers, heat exchangers and the pumps.
The heat exchangers used in the phosphoric acid unit present
exergetic efficiencies around 33% while 60% to 72% are obtained for
steam turbines and blower. For the explored ranges of HP steam
temperature and pressure, the exergy efficiencies of steam turbine
generators STGI and STGII increase of about 2.5% and 5.4%
respectively. In the same way optimum HP steam flow rate values,
leading to the maximum exergy efficiencies are defined.
Abstract: Concrete is an essential building material which is
widely used in construction industry all over the world due to its
compressible strength. Curing of concrete plays a vital role in
durability and other performance necessities. Improper curing can
affect the concrete performance and durability easily. When areas
like scarcity of water, structures is not accessible by humans external
curing cannot be performed, so we opt for internal curing. Internal
curing (or) self curing plays a major role in developing the concrete
pore structure and microstructure. The concept of internal curing is to
enhance the hydration process to maintain the temperature uniformly.
The evaporation of water in the concrete is reduced by self curing
agent (Super Absorbing Polymer – SAP) there by increasing the
water retention capacity of the concrete. The research work was
carried out to reduce water, which is prime material used for concrete
in the construction industry. Concrete curing plays a major role in
developing hydration process. Concept of self curing will reduce the
evaporation of water from concrete. Self curing will increase water
retention capacity as compared to the conventional concrete. Proper
self curing (or) internal curing increases the strength, durability and
performance of concrete. Super absorbing Polymer (SAP) used as
internal curing agent. In this study 0.2% to 0.4% of SAP was varied
in different grade of high strength concrete. In the experiment
replacement of cement by silica fumes with 5%, 10% and 15% are
studied. It is found that replacement of silica fumes by 10 % gives
more strength and durability when compared to others.
Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: In language learning, second language learners as well
as Native speakers commit errors in their attempt to achieve
competence in the target language. The realm of collocation has to do
with meaning relation between lexical items. In all human language,
there is a kind of ‘natural order’ in which words are arranged or relate
to one another in sentences so much so that when a word occurs in a
given context, the related or naturally co-occurring word will
automatically come to the mind. It becomes an error, therefore, if
students inappropriately pair or arrange such ‘naturally’ co–occurring
lexical items in a text. It has been observed that most of the second
language learners in this research group commit collocation errors. A
study of this kind is very significant as it gives insight into the kinds
of errors committed by learners. This will help the language teacher
to be able to identify the sources and causes of such errors as well as
correct them thereby guiding, helping and leading the learners
towards achieving some level of competence in the language. The
aim of the study is to understand the nature of these errors as
stumbling blocks to effective essay writing. The objective of the
study is to identify the errors, analyze their structural compositions so
as to determine whether there are similarities between students in this
regard and to find out whether there are patterns to these kinds of
errors which will enable the researcher to understand their sources
and causes. As a descriptive research, the researcher samples some
nine hundred essays collected from three hundred undergraduate
learners of English as a second language in the Federal College of
Education, Kano, North- West Nigeria, i.e. three essays per each
student. The essays which were given on three different lecture times
were of similar thematic preoccupations (i.e. same topics) and length
(i.e. same number of words). The essays were written during the
lecture hour at three different lecture occasions. The errors were
identified in a systematic manner whereby errors so identified were
recorded only once even if they occur severally in students’ essays.
The data was collated using percentages in which the identified
numbers of occurrences were converted accordingly in percentages.
The findings from the study indicate that there are similarities as well
as regular and repeated errors which provided a pattern. Based on the
pattern identified, the conclusion is that students’ collocation errors
are attributable to poor teaching and learning which resulted in wrong
generalization of rules.
Abstract: The crossover probability and mutation probability are the two important factors in genetic algorithm. The adaptive genetic algorithm can improve the convergence performance of genetic algorithm, in which the crossover probability and mutation probability are adaptively designed with the changes of fitness value. We apply adaptive genetic algorithm into a function optimization problem. The numerical experiment represents that adaptive genetic algorithm improves the convergence speed and avoids local convergence.
Abstract: The construction of most coastal infrastructure developments around the world are usually made considering wave height, current velocities and river discharges; however, little effort has been paid to surveying sediment transport during dredging or the modification to currents outside the ports or marinas during and after the construction. This study shows a complete survey during the construction of one of the largest ports of the Gulf of Mexico. An anchored Acoustic Doppler Current Velocity profiler (ADCP), a towed ADCP and a combination of model outputs were used at the Veracruz port construction in order to describe the hourly sediment transport and current modifications in and out of the new port. Owing to the stability of the system the new port was construction inside Vergara Bay, a low wave energy system with a tidal range of up to 0.40 m. The results show a two-current system pattern within the bay. The north side of the bay has an anticyclonic gyre, while the southern part of the bay shows a cyclonic gyre. Sediment transport trajectories were made every hour using the anchored ADCP, a numerical model and the weekly data obtained from the towed ADCP within the entire bay. The sediment transport trajectories were carefully tracked since the bay is surrounded by coral reef structures which are sensitive to sedimentation rate and water turbidity. The survey shows that during dredging and rock input used to build the wave breaker sediments were locally added (< 2500 m2) and local currents disperse it in less than 4 h. While the river input located in the middle of the bay and the sewer system plant may add more than 10 times this amount during a rainy day or during the tourist season. Finally, the coastal line obtained seasonally with a drone suggests that the southern part of the bay has not been modified by the construction of the new port located in the northern part of the bay, owing to the two subsystem division of the bay.