Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.
Abstract: As the demand and prices of various petroleum products have been on the rise in recent years, there is a growing need for alternative fuels. Biodiesel, which consists of alkyl monoesters of fatty acids from vegetable oils and animal fats, is considered as an alternative to petroleum diesel. Biodiesel has comparable performance with that of diesel and has lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC) and smoke with however, a slight increase in NOx emissions. This paper analyzes the effect of cooled exhaust gas recirculation in the combustion characteristics of a direct injection compression ignition engine using biodiesel blended fuel as opposed to the conventional system. The combustion parameters such as cylinder pressure, heat release rate, delay period and peak pressure were analyzed at various loads. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend the maximum rate of pressure rise was found to be higher for diesel at higher engine loads.
Abstract: The trend of growing density on chips has increases not
only the temperature in chips but also the gradient of the temperature
depending on locations. In this paper, we propose the balanced skew
tree generation technique for minimizing the clock skew that is
affected by the temperature gradients on chips. We calculate the
interconnect delay using Elmore delay equation, and find out the
optimal balanced clock tree by modifying the clock trees generated
through the Deferred Merge Embedding(DME) algorithm. The
experimental results show that the distance variance of clock insertion
points with and without considering the temperature gradient can be
lowered below 54% and we confirm that the skew is remarkably
decreased after applying the proposed technique.
Abstract: The detection of outliers is very essential because of
their responsibility for producing huge interpretative problem in
linear as well as in nonlinear regression analysis. Much work has
been accomplished on the identification of outlier in linear
regression, but not in nonlinear regression. In this article we propose
several outlier detection techniques for nonlinear regression. The
main idea is to use the linear approximation of a nonlinear model and
consider the gradient as the design matrix. Subsequently, the
detection techniques are formulated. Six detection measures are
developed that combined with three estimation techniques such as the
Least-Squares, M and MM-estimators. The study shows that among
the six measures, only the studentized residual and Cook Distance
which combined with the MM estimator, consistently capable of
identifying the correct outliers.
Abstract: Many works have been carried out to compare the
efficiency of several goodness of fit procedures for identifying
whether or not a particular distribution could adequately explain a
data set. In this paper a study is conducted to investigate the power
of several goodness of fit tests such as Kolmogorov Smirnov (KS),
Anderson-Darling(AD), Cramer- von- Mises (CV) and a proposed
modification of Kolmogorov-Smirnov goodness of fit test which
incorporates a variance stabilizing transformation (FKS). The
performances of these selected tests are studied under simple
random sampling (SRS) and Ranked Set Sampling (RSS). This
study shows that, in general, the Anderson-Darling (AD) test
performs better than other GOF tests. However, there are some
cases where the proposed test can perform as equally good as the
AD test.
Abstract: Preliminary results for a new flat plate test
facility are presented here in the form of Computational Fluid Dynamics (CFD), flow visualisation, pressure measurements and thermal anemometry. The results from the CFD and flow
visualisation show the effectiveness of the plate design, with the trailing edge flap anchoring the stagnation point on the working surface and reducing the extent of the leading edge separation. The flow visualization technique demonstrates the
two-dimensionality of the flow in the location where the
thermal anemometry measurements are obtained.
Measurements of the boundary layer mean velocity profiles compare favourably with the Blasius solution, thereby allowing for comparison of future measurements with the
wealth of data available on zero pressure gradient Blasius
flows. Results for the skin friction, boundary layer thickness,
frictional velocity and wall shear stress are shown to agree well with the Blasius theory, with a maximum experimental deviation from theory of 5%. Two turbulence generating grids
have been designed and characterized and it is shown that the turbulence decay downstream of both grids agrees with established correlations. It is also demonstrated that there is
little dependence of turbulence on the freestream velocity.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: The two significant overvoltages in power system,
switching overvoltage and lightning overvoltage, are investigated in
this paper. Firstly, the effect of various power system parameters on
Line Energization overvoltages is evaluated by simulation in ATP.
The dominant parameters include line parameters; short-circuit
impedance and circuit breaker parameters. Solutions to reduce
switching overvoltages are reviewed and controlled closing using
switchsync controllers is proposed as proper method.
This paper also investigates lightning overvoltages in the
overhead-cable transition. Simulations are performed in
PSCAD/EMTDC. Surge arresters are applied in both ends of cable to
fulfill the insulation coordination. The maximum amplitude of
overvoltages inside the cable is surveyed which should be of great
concerns in insulation coordination studies.
Abstract: In this project electrical and optical properties of
BaZrO3 have been accomplished through the full-potential
linear augmented plane wave (FP-LAPW) by applying Wein2k
software. In this study band structure, density of state, gap energy,
refractive index and optical conduction have been studied. The results
of calculations show that BaZrO3 is an insulator with an indirect gap
in which 3.2 ev and studied refractive index equal 2.07. These results
are in accordance with the ones obtained in experimental researches.
Abstract: Inconel718 has been widely used as a super alloy in aerospace application due to the high strength at elevated temperatures, satisfactory oxidation resistance and heat corrosion resistance. In this study, the Inconel718 has been fabricated using high technology of Metal Injection Molding (MIM) process due to the cost effective technique for producing small, complex and precision parts in high volume compared with conventional method through machining. Through MIM, the binder system is one of the most important criteria in order to successfully fabricate the Inconel718. Even though, the binder system is a temporary, but failure in the selection and removal of the binder system will affect on the final properties of the sintered parts. Therefore, the binder system based on palm oil derivative which is palm stearin has been formulated and developed to replace the conventional binder system. The rheological studies of the mixture between the powder and binders system have been determined properly in order to be successful during injection into injection molding machine. After molding, the binder holds the particles in place. The binder system has to be removed completely through debinding step. During debinding step, solvent debinding and thermal pyrolysis has been used to remove completely of the binder system. The debound part is then sintered to give the required physical and mechanical properties. The results show that the properties of the final sintered parts fulfill the Standard Metal Powder Industries Federation (MPIF) 35 for MIM parts.
Abstract: This study focuses on bureau management
technologies and information systems in developing countries.
Developing countries use such systems which facilitate executive and
organizational functions through the utilization of bureau
management technologies and provide the executive staff with
necessary information.
The concepts of data and information differ from each other in
developing countries, and thus the concepts of data processing and
information processing are different. Symbols represent ideas,
objects, figures, letters and numbers. Data processing system is an
integrated system which deals with the processing of the data related
to the internal and external environment of the organization in order
to make decisions, create plans and develop strategies; it goes
without saying that this system is composed of both human beings
and machines. Information is obtained through the acquisition and
the processing of data. On the other hand, data are raw
communicative messages. Within this framework, data processing
equals to producing plausible information out of raw data.
Organizations in developing countries need to obtain information
relevant to them because rapid changes in the organizational arena
require rapid access to accurate information. The most significant
role of the directors and managers who work in the organizational
arena is to make decisions. Making a correct decision is possible only
when the directors and managers are equipped with sound ideas and
appropriate information. Therefore, acquisition, organization and
distribution of information gain significance. Today-s organizations
make use of computer-assisted “Management Information Systems"
in order to obtain and distribute information.
Decision Support System which is closely related to practice is an
information system that facilitates the director-s task of making
decisions. Decision Support System integrates human intelligence,
information technology and software in order to solve the complex
problems. With the support of the computer technology and software
systems, Decision Support System produces information relevant to
the decision to be made by the director and provides the executive
staff with supportive ideas about the decision.
Artificial Intelligence programs which transfer the studies and
experiences of the people to the computer are called expert systems.
An expert system stores expert information in a limited area and can
solve problems by deriving rational consequences.
Bureau management technologies and information systems in
developing countries create a kind of information society and
information economy which make those countries have their places
in the global socio-economic structure and which enable them to play
a reasonable and fruitful role; therefore it is of crucial importance to
make use of information and management technologies in order to
work together with innovative and enterprising individuals and it is
also significant to create “scientific policies" based on information
and technology in the fields of economy, politics, law and culture.
Abstract: Common acceptable cuisine usually discussed in the
multicultural/ethnic nation as it represents the process of sharing it
among the ethnic groups. The common acceptable cuisine is also
considered as a precursor in the process of constructing the national
food identity within ethnic groups in the multicultural countries. The
adaptation of certain ethnic cuisines through its types of food,
methods of cooking, ingredients and eating decorum by ethnic groups
is believed creating or enhancing the process of formation on
common acceptable cuisines in a multicultural country. Malaysia as
the multicultural country without doubt is continuing to experience
cross-culturing processes among the ethnic groups including cuisine.
This study empirically investigates the adaptation level of Malay,
Chinese and Indian chefs on each other ethnic cuisine attributes
toward the formation on common acceptable cuisines and national
food identity.
Abstract: Growth and mineral nutrient elemental content were
studied in Mokara chark kuan pink terrestrial orchid and wild
Lantana camara weed agroecosystem. The treated subplots were
encircled with L. camara plants and sprayed weekly with L. camara
10% leaf aqueous extract. Allelopathic interactions were possible
through extensive invading root of L. camara plants into the treated
orchid subplots and weekly L. camara leaf aqueous extract
sprayings. Orchid growth was not significantly different in between
the control and treated plots, but chlorosis and yellowish patches of
leaves were observed in control orchid leaves. Nitrogen content in L.
camara leaf was significantly higher than in orchid leaf, the order of
importance of mineral nutrient contents in L. camara leaf was
K>Mg>Na>N. In treated orchid leaf, the order of importance was
N>K>Mg>Na. Orchid leaf N content from the treated plot was
higher than control, but Mg and Na contents were almost similar.
Abstract: The effect of seed inoculation by VA- mycorrhiza and
different levels of phosphorus fertilizer on growth and yield of
sunflower (Azargol cultivar) was studied in experiment farm of
Islamic Azad University, Karaj Branch during 2008 growing season.
The experiment treatments were arranged in factorial based on a
complete randomized block design with three replications. Four
phosphorus fertilizer levels of 25%, 50% 75% and 100% P
recommended with two levels of Mycorrhiza: with and without
Mycorrhiza (control) were assigned in a factorial combination.
Results showed that head diameter, number of seeds in head, seed
yield and oil yield were significantly higher in inoculated plants than
in non-inoculated plants. Head diameter, number of seeds in head,
1000 seeds weight, biological yield, seed yield and oil yield increased
with increasing P level above 75% P recommended in non-inoculated
plants, whereas no significant difference was observed between 75%
and 100% P recommended. The positive effect of mycorrhizal
inoculation decreased with increasing P levels due to decreased
percent root colonization at higher P levels. According to the results
of this experiment, application of mycorrhiza in present of 50% P
recommended had an appropriate performance and could increase
seed yield and oil production to an acceptable level, so it could be
considered as a suitable substitute for chemical phosphorus fertilizer
in organic agricultural systems.
Abstract: This paper maps the structure of the social network of
the 2011 class ofsixty graduate students of the Masters of Science
(Knowledge Management) programme at the Nanyang Technological
University, based on their friending relationships on Facebook. To
ensure anonymity, actual names were not used. Instead, they were
replaced with codes constructed from their gender, nationality, mode
of study, year of enrollment and a unique number. The relationships
between friends within the class, and among the seniors and alumni
of the programme wereplotted. UCINet and Pajek were used to plot
the sociogram, to compute the density, inclusivity, and degree,
global, betweenness, and Bonacich centralities, to partition the
students into two groups, namely, active and peripheral, and to
identify the cut-points. Homophily was investigated, and it was
observed for nationality and study mode. The groups students formed
on Facebook were also studied, and of fifteen groups, eight were
classified as dead, which we defined as those that have been inactive
for over two months.
Abstract: This paper presents the results of an experimental
investigation carried out to evaluate the shrinkage of High Strength
Concrete. High Strength Concrete is made by partially replacement of
cement by flyash and silica fume. The shrinkage of High Strength
Concrete has been studied using the different types of coarse and fine
aggregates i.e. Sandstone and Granite of 12.5 mm size and Yamuna
and Badarpur Sand. The Mix proportion of concrete is 1:0.8:2.2 with
water cement ratio as 0.30. Superplasticizer dose @ of 2% by weight
of cement is added to achieve the required degree of workability in
terms of compaction factor.
From the test results of the above investigation it can be concluded
that the shrinkage strain of High Strength Concrete increases with
age. The shrinkage strain of concrete with replacement of cement by
10% of Flyash and Silica fume respectively at various ages are more
(6 to 10%) than the shrinkage strain of concrete without Flyash and
Silica fume. The shrinkage strain of concrete with Badarpur sand as
Fine aggregate at 90 days is slightly less (10%) than that of concrete
with Yamuna Sand. Further, the shrinkage strain of concrete with
Granite as Coarse aggregate at 90 days is slightly less (6 to 7%) than
that of concrete with Sand stone as aggregate of same size. The
shrinkage strain of High Strength Concrete is also compared with that
of normal strength concrete. Test results show that the shrinkage
strain of high strength concrete is less than that of normal strength
concrete.
Abstract: This paper describes technological possibilities to
enhance methane productionin the anaerobic stabilization of wastewater treatment plant excess sludge. This objective can be achieved by the addition of waste residues: crude glycerol from biodiesel production and residues from fishery. The addition
ofglycerol in an amount by weight of 2 – 5% causes enhancement of methane production of about 250 – 400%. At the same time the
percentage increase of total solids concentration in the outgoing sludge is ten or more times less. The containment of methane in
biogas is higher in case of admixed substrate.
Abstract: In this research, an anaerobic co-digestion using decanter cake from palm oil mill industry to improve the biogas production from frozen seafood wastewater is studied using Continuously Stirred Tank Reactor (CSTR) process. The experiments were conducted in laboratory-scale. The suitable Hydraulic Retention Time (HRT) was observed in CSTR experiments with 24 hours of mixing time using the mechanical mixer. The HRT of CSTR process impacts on the efficiency of biogas production. The best performance for biogas production using CSTR process was the anaerobic codigestion for 20 days of HRT with the maximum methane production rate of 1.86 l/d and the average maximum methane production of 64.6%. The result can be concluded that the decanter cake can improve biogas productivity of frozen seafood wastewater.
Abstract: Advances in technology (e.g. the internet,
telecommunication) and political changes (fewer trade barriers and an
enlarged European Union, ASEAN, NAFTA and other organizations)
have led to develop international competition and expand into new
markets. Companies in Thailand, Asia and around the globe are
increasingly being pressured on price and for faster time to enter the
market. At the same time, new markets are appearing and many
companies are looking for changes and shifts in their domestic
markets. These factors have enabled the rapid growth for companies
and globalizing many different business activities during the product
development process from research and development (R&D) to
production.
This research will show and clarify methods how to develop
global product. Also, it will show how important is a global product
impact into Thai Economy development.
Abstract: In the present study, development of salbutamol
sulphate nanoparticles that adhere to gastric mucus was investigated.
Salbutamol sulphate has low bioavailability due to short transit time in
gastric. It also has a positive surface charge that provides hurdles to be
encapsulated by the positively strong mucoadhesive polymer of
chitosan. To overcome the difficulties, the surface charge of active
ingredient was modified using several nonionic and anionic
stomach-specific polymers. The nanoparticles were prepared using
ionotropic gelation technique. The evaluation involved determination
of particle size, zeta potential, entrapment efficiency, in vitro drug
release and in vitro mucoadhesion test. Results exhibited that the use
of anionic alginate polymer was more satisfactory than that of
nonionic polymer. Characteristics of the particles was nano-size, high
encapsulation efficiency, fulfilled the drug release requirements and
adhesive towards stomach for around 11 hours. This result shows that
the salbutamol sulphate nanoparticles can be utilized for improvement
its delivery.