Abstract: The housing industry is crucial for sustainable
development of every country. Housing is a basic need that can
enhance the quality of life. Owning a house is therefore the main aim
of individuals. However, affordability has become a critical issue
towards homeownership. In recent years, housing price in the main
cities has increased tremendously to unaffordable level. This paper
investigates factors influencing the housing price from developer’s
perspective and provides recommendation on strategies to tackle this
issue. Online and face-to-face survey was conducted on housing
developers operating in Penang, Malaysia. The results indicate that
(1) location; (2) macroeconomics factor; (3) demographic factors; (4)
land/zoning and; (5) industry factors are the main factors influencing
the housing price. This paper contributes towards better
understanding on developers’ view on how the housing price is
determined and form a basis for government to help tackle the
housing affordability issue.
Abstract: High reflectance of surgical instruments under bright
light hinders the visual clarity during laparoscopic surgical
procedures leading to loss of precision and device control and creates
strain and undesired difficulties to surgeons. Majority of the surgical
instruments are made of surgical grade steel. Instruments with a non
reflective surface can enhance the visual clarity during precision
surgeries. A conversion coating of black oxide has been successfully
developed 410 grade surgical stainless steel .The characteristics of
the developed coating suggests the application of this technique for
developing 410 grade surgical instruments with minimal reflectance.
Abstract: Waste polyethylene (PE) is classified as waste low
density polyethylene (LDPE) and waste high density polyethylene
(HDPE) according to their densities. Pyrolysis of plastic waste may
have an important role in dealing with the enormous amounts of
plastic waste produced all over the world, by decreasing their
negative impact on the environment. This waste may be converted
into economically valuable hydrocarbons, which can be used both as
fuels and as feed stock in the petrochemical industry. End product
yields and properties depend on the plastic waste composition.
Pyrolytic biochar is one of the most important products of waste
plastics pyrolysis. In this study, HDPE and LDPE plastic wastes were
co-pyrolyzed together with waste olive pomace. Pyrolysis runs were
performed at temperature 700°C with heating rates of 5°C/min.
Higher pyrolysis oil and gas yields were observed by the using waste
olive pomace. The biochar yields of HDPE- olive pomace and LDPEolive
pomace were 6.37% and 7.26% respectively for 50% olive
pomace doses. The calorific value of HDPE-olive pomace and
LDPE-olive pomace of pyrolysis oil were 8350 and 8495 kCal.
Abstract: The aim of the paper is to investigate the effect of
corporate social responsibility (CSR) CSR on the National
Commercial Bank (NCB) in Saudi Arabia. In order to achieve this, a
case study was made of the CSR activities of this bank from the
perspective of its branch managers. The NCB was chosen as it was
one of the first Saudi banks to engage in CSR and currently has a
wide range of CSR initiatives. A qualitative research method was
used. Open-ended questionnaires were administered to eighty branch
managers of the NCB, with fifty-five usable questionnaires returned
and twenty managers were interviewed as part of the primary
research. Data from both questionnaires and interviews were
analysed using qualitative content analysis. Six themes emerged from
the questionnaire findings were used to develop the interview
questions. These themes are the following: Awareness of employees
about CSR in the NCB; CSR activities as a type of investment;
Government and media support; Increased employee loyalty in the
NCB; Prestige and profit to the NCB; and View of CSR in Islam.
This paper makes a theoretical contribution in that it investigates and
increases understanding of the effect of CSR on the NCB in Saudi
Arabia. In addition, it makes a practical contribution by making
recommendations which can support the development of CSR in the
NCB. A limitation of the paper is that it is a case study of only one
bank. It is therefore recommended that future research could be
conducted with other banks in Saudi Arabia, or indeed, with a range
of other types of firm within the financial services area in Saudi
Arabia. In this way, the same issues could be explored but with a
greater potential generalisability of findings of CSR within the Saudi
Arabian financial services industry. In addition, this paper takes a
qualitative approach and it is suggested that future research be carried
out using mixed methods, which could provide a greater depth of
analysis.
Abstract: Discrimination against women and girls impairs progress in all domains of development articulated either in the framework of Millennium Development Goals (MDGs) or in the Post-2015 Development Agenda. Paper aspires to create greater awareness among researchers and policy makers of the challenges posed by gender gaps and the opportunities created by reducing them within the Arab region. The study reveals how Arab countries are closing in on gender-oriented targets of the third and fifth MDGs. While some countries can claim remarkable achievements particularly in girls’ equality in education, there is still a long way to go to keep Arab’s commitments to current and future generations in other countries and subregions especially in the economic participation or in the political empowerment of women. No country has closed or even expected to close the economic participation gap or the political empowerment gap. This should provide the incentive to keep moving forward in the Post-2015 Agenda. Findings of the study prove that while Arab states have uneven achievements in reducing maternal mortality, Arab women remain at a disadvantage in the labour market. For Arab region especially LDCs, improving maternal health is part of the unmet agenda for the post-2015 period and still calls for intensified efforts and procedures. While antenatal care coverage is improving across the Arab region, progress is marginal in LDCs. To achieve proper realization of gender equality and empowerment of women in the Arab region in the post-2015 agenda, the study presents critical key challenges to be addressed. These challenges include: Negative cultural norms and stereotypes; violence against women and girls; early marriage and child labour; women’s limited control over their own bodies; limited ability of women to generate their own income and control assets and property; gender-based discrimination in law and in practice; women’s unequal participation in private and public decision making autonomy; and limitations in data. However, in all Arab states, gender equality must be integrated as a goal across all issues, particularly those that affect the future of a country.
Abstract: This study presents an inverse analysis for predicting the thermal conductivities and the heat flux of a high-temperature metallurgical reactor simultaneously. Once these thermal parameters are predicted, the time-varying thickness of the protective phase-change bank that covers the inside surface of the brick walls of a metallurgical reactor can be calculated. The enthalpy method is used to solve the melting/solidification process of the protective bank. The inverse model rests on the Levenberg-Marquardt Method (LMM) combined with the Broyden method (BM). A statistical analysis for the thermal parameter estimation is carried out. The effect of the position of the temperature sensors, total number of measurements and measurement noise on the accuracy of inverse predictions is investigated. Recommendations are made concerning the location of temperature sensors.
Abstract: In an economic crisis such as the one that shook (and still shake) Europe, one does not question the importance of the measures that encourage the hiring and integration of young people into the labour market. In the mentioned context, enterprises tend to reduce the cost of labour and to seek flexible contracting instruments. The professional internships allow innovation and creativity at low cost, because, as they are not labour contracts, the enterprises do not have to respect the minimum standards related to wages, working time duration and so on. In Portugal, we observe a widespread existence of training contracts in which the trainee worked several hours without salary or was paid below the legally prescribed for the function and the work period. For this reason, under the tripartite agreement for a new system of regulation of labour relations, employment policies and social protection, between the Government and the social partners, in June 2008, foresaw a prohibition of professional internships unpaid and the legal regulation of the mandatory internships for access to an activity. The first Act about private internship contracts, i.e., internships without public funding was embodied in the Decree-Law N. 66/2011, of 1st June. This work is dedicated to the study of the legal regime of the internship contract in Portugal, by analysing the problems brought by the new set of rules and especially those which remains unresolved. In fact, we can conclude that the number of situations covered by the Act is much lower than what was expected, because of the exclusion of the mandatory internship for access to a profession when the activity is developed autonomously. Since the majority of the activities can be developed both autonomously or subordinated, it is quite easy to out of the Act requirements and, so, out of the protection that it confers to the intern. In order to complete this study, we considered not only the mentioned legal Act, but also the few doctrine and jurisprudence about the theme.
Abstract: With the increasing complexity of cyberspace security, the cyber-attack attribution has become an important challenge of the security protection systems. The difficult points of cyber-attack attribution were forced on the problems of huge data handling and key data missing. According to this situation, this paper presented a reasoning method of cyber-attack attribution based on threat intelligence. The method utilizes the intrusion kill chain model and Bayesian network to build attack chain and evidence chain of cyber-attack on threat intelligence platform through data calculation, analysis and reasoning. Then, we used a number of cyber-attack events which we have observed and analyzed to test the reasoning method and demo system, the result of testing indicates that the reasoning method can provide certain help in cyber-attack attribution.
Abstract: Solid particle erosion has been identified as a critical wear phenomenon which takes place during operation of aeroengines in dusty environment. The present work discusses the erosion behavior of Ti-44.5Al-6.25Nb-0.8Mo-0.1B alloy (TNB-V4) which finds its application in low pressure gas turbines and can be used for high pressure compressors too. Prior to the erosion tests, the alloy was heat treated to improve the mechanical properties. Afterwards, specimens were eroded at impact angles of 30° and 90° at room and high temperatures (100 °C-400 °C). Volume loss and erosion behavior are studied through gravimetric analysis, whereas erosion mechanisms are characterized through scanning electron microscopy. The results indicate a clear difference in the erosion mechanism for different impact angles. The influence of the test temperature on the erosion behavior of the alloy is also discussed in the present contribution.
Abstract: Particle reinforced Metal Matrix Composite (MMC) succeeds in synergizing the metallic matrix with ceramic particle reinforcements to result in improved strength, particularly at elevated temperatures, but adversely it affects the ductility of the matrix because of agglomeration and porosity. The present study investigates the outcome of tensile properties in a cast and hot forged composite reinforced simultaneously with coarse and fine particles. Nano-sized alumina particles have been generated by milling mixture of aluminum and manganese dioxide powders. Milled particles after drying are added to molten metal and the resulting slurry is cast. The microstructure of the composites shows good distribution of both the size categories of particles without significant clustering. The presence of nanoparticles along with coarser particles in a composite improves both strength and ductility considerably. Delay in debonding of coarser particles to higher stress is due to reduced mismatch in extension caused by increased strain hardening in presence of the nanoparticles. However, higher addition of powder mix beyond a limit results in deterioration of mechanical properties, possibly due to clustering of nanoparticles. The porosity in cast composite generally increases with the increasing addition of powder mix as observed during process and on forging it has got reduced. The base alloy and nanocomposites show improvement in flow stress which could be attributed to lowering of porosity and grain refinement as a consequence of forging.
Abstract: Operators of vessel traffic service (VTS) center provides three different types of services; namely information service, navigational assistance and traffic organization to vessels. To provide these services, operators monitor vessel traffic through computer interface and provide navigational advice based on the information integrated from multiple sources, including automatic identification system (AIS), radar system, and closed circuit television (CCTV) system. Therefore, this information is crucial in VTS operation. However, what information the VTS operator actually need to efficiently and properly offer services is unclear. The aim of this study is to investigate into information requirements for VTS operation. To achieve this aim, field observation was carried out to elicit the information requirements for VTS operation. The study revealed that the most frequent and important tasks were handling arrival vessel report, potential conflict control and abeam vessel report. Current location and vessel name were used in all tasks. Hazard cargo information was particularly required when operators handle arrival vessel report. The speed, the course, and the distance of two or several vessels were only used in potential conflict control. The information requirements identified in this study can be utilized in designing a human-computer interface that takes into consideration what and when information should be displayed, and might be further used to build the foundation of a decision support system for VTS.
Abstract: Monitoring of tool wear in milling operations is essential for achieving the desired dimensional accuracy and surface finish of a machined workpiece. Although there are numerous statistical models and artificial intelligence techniques available for monitoring the wear of cutting tools, these techniques cannot pin point which cutting edge of the tool, or which insert in the case of indexable tooling, is worn or broken. Currently, the task of monitoring the wear on the tool cutting edges is carried out by the operator who performs a manual inspection, causing undesirable stoppages of machine tools and consequently resulting in costs incurred from lost productivity. The present study is concerned with the development of a flute tracking system to segment signals related to each physical flute of a cutter with three flutes used in an end milling operation. The purpose of the system is to monitor the cutting condition for individual flutes separately in order to determine their progressive wear rates and to predict imminent tool failure. The results of this study clearly show that signals associated with each flute can be effectively segmented using the proposed flute tracking system. Furthermore, the results illustrate that by segmenting the sensor signal by flutes it is possible to investigate the wear in each physical cutting edge of the cutting tool. These findings are significant in that they facilitate the online condition monitoring of a cutting tool for each specific flute without the need for operators/engineers to perform manual inspections of the tool.
Abstract: A uniquely restricted matching is defined to be a
matching M whose matched vertices induces a sub-graph which has
only one perfect matching. In this paper, we make progress on the
open question of the status of this problem on interval graphs (graphs
obtained as the intersection graph of intervals on a line). We give
an algorithm to compute maximum cardinality uniquely restricted
matchings on certain sub-classes of interval graphs. We consider two
sub-classes of interval graphs, the former contained in the latter, and
give O(|E|^2) time algorithms for both of them. It is to be noted that
both sub-classes are incomparable to proper interval graphs (graphs
obtained as the intersection graph of intervals in which no interval
completely contains another interval), on which the problem can be
solved in polynomial time.
Abstract: There is a requirement for registered edible seed pumpkin suitable for eating in Turkey. A total of 81 genotypes collected from the researchers in 2005 originated from Eskisehir, Konya, Nevsehir, Tekirdag, Sakarya, Kayseri and Kirsehir provinces were utilized. The used genetic materials were brought to S5 generation by the research groups among 2006 and 2010 years. In this research, S5 stage reached in the genotype given some of the morphological features, and selection of promising genotypes generated scale were made. Results showed that the A-1 (420), A-7 (410), A-8 (420), A-32 (420), B-17 (410), B-24 (410), B-25 (420), B-33 (400), C-24 (420), C-25 (410), C-26 (410) and C-30 (420) genotypes are expected to be promising varieties.
Abstract: Fluoroquinolones form the mainstay of therapy for the treatment of infections due to Salmonella enterica subsp. enterica. There is a complex interplay between several resistance mechanisms for quinolones and various fluoroquinolones discs, giving varying results, making detection and interpretation of fluoroquinolone resistance difficult. For detection of fluoroquinolone resistance in Salmonella ssp., we compared the use of pefloxacin and nalidixic acid discs as surrogate marker. Using MIC for ciprofloxacin as the gold standard, 43.5% of strains showed MIC as ≥1 μg/ml and were thus resistant to fluoroquinoloes. Based on the performance of nalidixic acid and pefloxacin discs as surrogate marker for ciprofloxacin resistance, both the discs could correctly detect all the resistant phenotypes; however, use of nalidixic acid disc showed false resistance in the majority of the sensitive phenotypes. We have also tested newer antimicrobial agents like cefixime, imipenem, tigecycline and azithromycin against Salmonella spp. Moreover, there was a comeback of susceptibility to older antimicrobials like ampicillin, chloramphenicol, and cotrimoxazole. We can also use cefixime, imipenem, tigecycline and azithromycin in the treatment of multidrug resistant S. typhi due to their high susceptibility.
Abstract: In this paper, the design of a QCM sensor for liquid media measurements in vertical position is described. A rugged and low-cost proof holder has been designed, the cost of which is significantly lower than those of traditional commercial holders. The crystal is not replaceable but it can be easily cleaned. Its small volume permits to be used by dipping it in the liquid with the desired location and orientation. The developed design has been experimentally validated by measuring changes in the resonance frequency and resistance of the QCM sensor immersed vertically in different calibrated aqueous glycerol solutions. The obtained results show a great agreement with the Kanazawa theoretical expression. Consequently, the designed QCM sensor would be appropriate for sensing applications in liquids, and might take part of a future on-line multichannel low-cost QCM-based measurement system.
Abstract: Despite all progress firms are facing the increasing need to adapt and assimilate digital technologies to transform their business activities in order to pursue business development. By using new digital technologies, firms can implement major business improvements in order to stay competitive and foster new growth potentials. The corresponding phenomenon of digital transformation has received some attention in previous literature in respect to industries such as media and publishing. Nevertheless, there is a lack of understanding of the concept and its organization within firms. With the help of twenty-three in-depth field interviews with German experts responsible for their company’s digital transformation, we examined what digital transformation encompasses, how it is organized and which opportunities and challenges arise within firms. Our results indicate that digital transformation is an inevitable task for all firms, as it bears the potential to comprehensively optimize and reshape established business activities and can thus be seen as a strategy of business development.
Abstract: Modeling of hydrogen fueled engine (H2ICE) injection system is a very important tool that can be used for explaining or predicting the effect of advanced injection strategies on combustion and emissions. In this paper, a common rail injection system (CRIS) is proposed for 4-strokes 4-cylinders hydrogen fueled engine with port injection feeding system (PIH2ICE). For this system, a numerical one-dimensional gas dynamic model is developed considering single injection event for each injector per a cycle. One-dimensional flow equations in conservation form are used to simulate wave propagation phenomenon throughout the CR (accumulator). Using this model, the effect of common rail on the injection system characteristics is clarified. These characteristics include: rail pressure, sound velocity, rail mass flow rate, injected mass flow rate and pressure drop across injectors. The interaction effects of operational conditions (engine speed and rail pressure) and geometrical features (injector hole diameter) are illustrated; and the required compromised solutions are highlighted. The CRIS is shown to be a promising enhancement for PIH2ICE.
Abstract: In this paper, we study the data collection problem in
Wireless Sensor Networks (WSNs) adopting the two interference
models: The graph model and the more realistic physical interference
model known as Signal-to-Interference-Noise-Ratio (SINR). The
main issue of the problem is to compute schedules with the minimum
number of timeslots, that is, to compute the minimum latency
schedules, such that data from every node can be collected without
any collision or interference to a sink node. While existing works
studied the problem with unit-sized and unbounded-sized message
models, we investigate the problem with the bounded-sized message
model, and introduce a constant factor approximation algorithm.
To the best known of our knowledge, our result is the first result
of the data collection problem with bounded-sized model in both
interference models.
Abstract: In the study, we present a conceptual framework for developing a scheduling system that can generate self-explanatory and easy-understanding schedules. To this end, a user interface is conceived to help planners record factors that are considered crucial in scheduling, as well as internal and external sources relating to such factors. A hybrid approach combining machine learning and constraint programming is developed to generate schedules and the corresponding factors, and accordingly display them on the user interface. Effects of the proposed system on scheduling are discussed, and it is expected that scheduling efficiency and system understandability will be improved, compared with previous scheduling systems.