Abstract: The heterotrophic seedling growth can be defined as a
product of two components: (1) the weight of mobilized seed reserve,
and (2) conversion efficiency of utilized seed reserve to seedling
tissue. The first component can be further divided into (1) initial seed
weight, and (2) the fraction of seed reserve, which is mobilized. The
objective of this study was the identification of the sensitive seedling
growth component(s) in response to drought and salinity stresses.
Two experiments were separately conducted using various salinity
levels (osmotic pressure) of 0, 0.25, 0.50, 0.75, 1, 1.25 and 1.5 MPa
created using NaCl as first experiment and by polyethylene glycol
(drought stress) of 0, 0.2, 0.4, 0.6, 0.8, 1, 1.2 and 1.4 MPa in second
experiment. Seeds of five crops species (Hordeum vulgare, Brassica
napus, Zea mays, Medicago sativa and Medicago scutellata) were
used in each experiment. In both experiments, seedling growth,
fraction of seed reserve utilization and weight of mobilized seed
reserve decreased with increasing drought and salt intensity.
However, drought and salinity stresses had no effect on the
conversion efficiency. It was concluded that the sensitive component
of seedling growth is the weight of mobilized seed reserve.
Abstract: Hierarchical Mobile IPv6 (HMIPv6) was designed to
support IP micro-mobility management in the Next Generation
Networks (NGN) framework. The main design behind this protocol is
the usage of Mobility Anchor Point (MAP) located at any level router
of network to support hierarchical mobility management. However,
the distance MAP selection in HMIPv6 causes MAP overloaded and
increase frequent binding update as the network grows. Therefore, to
address the issue in designing MAP selection scheme, we propose a
dynamic load control mechanism integrates with a speed detection
mechanism (DMS-DLC). From the experimental results we obtain
that the proposed scheme gives better distribution in MAP load and
increase handover speed.
Abstract: This paper presents the results of preliminary
assessment of water quality along the coastal areas in the vicinity of
Left Bank Outfall Drainage (LBOD) and Tidal Link Drain (TLD) in
Sindh province after the cyclone 2A occurred in 1999. The water
samples were collected from various RDs of Tidal Link Drain and
lakes during September 2001 to April 2002 and were analysed for
salinity, nitrite, phosphate, ammonia, silicate and suspended material
in water. The results of the study showed considerable variations in
water quality depending upon the location along the coast in the
vicinity of LBOD and RDs. The salinity ranged between 4.39–65.25
ppt in Tidal Link Drain samples whereas 2.4–38.05 ppt in samples
collected from lakes. The values of suspended material at various
RDs of Tidal Link Drain ranged between 56.6–2134 ppm and at the
lakes between 68–297 ppm. The data of continuous monitoring at
RD–93 showed the range of PO4 (8.6–25.2 μg/l), SiO3 (554.96–1462
μg/l), NO2 (0.557.2–25.2 μg/l) and NH3 (9.38–23.62 μg/l). The
concentration of nutrients in water samples collected from different
RDs was found in the range of PO4 (10.85 to 11.47 μg/l), SiO3 (1624
to 2635.08 μg/l), NO2 (20.38 to 44.8 μg/l) and NH3 (24.08 to 26.6
μg/l). Sindh coastal areas which situated at the north-western
boundary the Arabian Sea are highly vulnerable to flood damages
due to flash floods during SW monsoon or impact of sea level rise
and storm surges coupled with cyclones passing through Arabian Sea
along Pakistan coast. It is hoped that the obtained data in this study
would act as a database for future investigations and monitoring of
LBOD and Tidal Link Drain coastal waters.
Abstract: This paper presents the influence of preloading on a)
the contact tractions, b) slip levels and c) stresses at the dovetail
blade-disc interface of an aero-engine through a three-dimensional
(3D) finite element (FE) modeling and analysis. The preloading is
applied by an interference fit at the dovetail interface and the bulk
loading is applied through the rotational speed of rotor. Preloading at
the dovetail interface reduces the peak contact pressure developed
due to bulk loading up to 35%, and reduces the peak contact pressure
and stress difference between top and bottom contact edges.
Increasing the level of preloading reduces the cyclic stress amplitude
at the interface up to certain values of preload and as a consequence,
an improvement in fatigue life could be expected. Fretting damage,
due to vibration and wind milling effect during engine ground
condition, can be minimized by preloading the dovetail interface.
Abstract: This paper is concerned with an improved algorithm
based on the piecewise-smooth Mumford and Shah (MS) functional
for an efficient and reliable segmentation. In order to speed up
convergence, an additional force, at each time step, is introduced
further to drive the evolution of the curves instead of only driven by
the extensions of the complementary functions u + and u - . In our
scheme, furthermore, the piecewise-constant MS functional is
integrated to generate the extra force based on a temporary image that
is dynamically created by computing the union of u + and u - during
segmenting. Therefore, some drawbacks of the original algorithm,
such as smaller objects generated by noise and local minimal problem
also are eliminated or improved. The resulting algorithm has been
implemented in Matlab and Visual Cµ, and demonstrated efficiently
by several cases.
Abstract: A seismic isolation pad produced by utilizing the scrap
tire rubber which contains interleaved steel reinforcing cords has been
proposed. The steel cords are expected to function similar to the steel
plates used in conventional laminated rubber bearings. The scrap tire
rubber pad (STRP) isolator is intended to be used in low rise
residential buildings of highly seismic areas of the developing
countries. Experimental investigation was conducted on unbonded
STRP isolators, and test results provided useful information including
stiffness, damping values and an eventual instability of the isolation
unit. Finite element analysis (FE analysis) of STRP isolator was
carried out on properly bonded samples. These types of isolators
provide positive incremental force resisting capacity up to shear strain
level of 155%. This paper briefly discusses the force deformation
behavior of bonded STRP isolators including stability of the isolation
unit.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: This research were investigated, determined, and
analyzed of the climate characteristically change in the provincial
Udon Thani in the period of 60 surrounding years from 1951 to 2010
A.D. that it-s transferred to effects of climatologically data for
determining global warming. Statistically significant were not found
for the 60 years- data (R2
Abstract: This paper studies a vital issue in wireless
communications, which is the transmission of images over Wireless
Personal Area Networks (WPANs) through the Bluetooth network. It
presents a simple method to improve the efficiency of error control
code of old Bluetooth versions over mobile WPANs through
Interleaved Error Control Code (IECC) technique. The encoded
packets are interleaved by simple block interleaver. Also, the paper
presents a chaotic interleaving scheme as a tool against bursts of
errors which depends on the chaotic Baker map. Also, the paper
proposes using the chaotic interleaver instead of traditional block
interleaver with Forward Error Control (FEC) scheme. A comparison
study between the proposed and standard techniques for image
transmission over a correlated fading channel is presented.
Simulation results reveal the superiority of the proposed chaotic
interleaving scheme to other schemes. Also, the superiority of FEC
with proposed chaotic interleaver to the conventional interleavers
with enhancing the security level with chaotic interleaving packetby-
packet basis.
Abstract: Use of fly ash as a supplementary cementing material
in large volumes can bring both technological and economic benefits
for concrete industry. In this investigation mix proportions for high
volume fly ash concrete were determined at cement replacement
levels of 50%, 55%, 60% and 65% with low calcium fly ash. Flexural
and compressive strengths of different mixes were measured at ages
of 7, 28 and 90 days. Flexural strength of composite section prepared
from pavement quality and lean high volume fly ash concrete was
determined at the age of 28 days. High volume fly ash concrete mixes
exhibited higher rate of strength gain and age factors than
corresponding reference concrete mixes. The optimum cement
replacement level for pavement quality concrete was found to be
60%. The consideration of bond between pavement quality and lean
of high volume fly ash concrete will be beneficial in design of rigid
pavements.
Abstract: An on-line condition monitoring method for transmission line is proposed using electrical circuit theory and IT technology in this paper. It is reasonable that the circuit parameters such as resistance (R), inductance (L), conductance (g) and capacitance (C) of a transmission line expose the electrical conditions and physical state of the line. Those parameters can be calculated from the linear equation composed of voltages and currents measured by synchro-phasor measurement technique at both end of the line. A set of linear voltage drop equations containing four terminal constants (A, B ,C ,D ) are mathematical models of the transmission line circuits. At least two sets of those linear equations are established from different operation condition of the line, they may mathematically yield those circuit parameters of the line. The conditions of line connectivity including state of connecting parts or contacting parts of the switching device may be monitored by resistance variations during operation. The insulation conditions of the line can be monitored by conductance (g) and capacitance(C) measurements. Together with other condition monitoring devices such as partial discharge, sensors and visual sensing device etc.,they may give useful information to monitor out any incipient symptoms of faults. The prototype of hardware system has been developed and tested through laboratory level simulated transmission lines. The test has shown enough evident to put the proposed method to practical uses.
Abstract: Nowadays predicting political risk level of country
has become a critical issue for investors who intend to achieve
accurate information concerning stability of the business
environments. Since, most of the times investors are layman and
nonprofessional IT personnel; this paper aims to propose a
framework named GECR in order to help nonexpert persons to
discover political risk stability across time based on the political
news and events.
To achieve this goal, the Bayesian Networks approach was
utilized for 186 political news of Pakistan as sample dataset.
Bayesian Networks as an artificial intelligence approach has been
employed in presented framework, since this is a powerful technique
that can be applied to model uncertain domains. The results showed
that our framework along with Bayesian Networks as decision
support tool, predicted the political risk level with a high degree of
accuracy.
Abstract: Electronic commerce is growing rapidly with on-line
sales already heading for hundreds of billion dollars per year. Due to
the huge amount of money transferred everyday, an increased
security level is required. In this work we present the architecture of
an intelligent speaker verification system, which is able to accurately
verify the registered users of an e-commerce service using only their
voices as an input. According to the proposed architecture, a
transaction-based e-commerce application should be complemented
by a biometric server where customer-s unique set of speech models
(voiceprint) is stored. The verification procedure requests from the
user to pronounce a personalized sequence of digits and after
capturing speech and extracting voice features at the client side are
sent back to the biometric server. The biometric server uses pattern
recognition to decide whether the received features match the stored
voiceprint of the customer who claims to be, and accordingly grants
verification. The proposed architecture can provide e-commerce
applications with a higher degree of certainty regarding the identity
of a customer, and prevent impostors to execute fraudulent
transactions.
Abstract: Changing technology and increased constituent
demand for government services derive the need for governmental
responsiveness. The government organisations in the developing
countries will be under increased pressure to change their
bureaucratic systems to be able to respond rapidly to changing and
increasing requirements and rapid technology advancements. This
paper aims to present a conceptual framework for explaining the
main barriers and drivers of public e-service development. Therefore,
the framework provides a basic context within which the process and
practice of E-Service can be implemented successfully in the public
sector organisations. The framework is flexible enough to be adopted
by governments at different levels; national or local by developing
countries around the world.
Abstract: While in practice negotiation is always a mix of
cooperation and competition, these two elements correspond to
different approaches of the relationship and also different orientations
in term of strategy, techniques, tactics and arguments employed by
the negotiators with related effects and in the end leading to different
outcomes. The levels of honesty, trust and therefore cooperation are
influenced not only by the uncertainty of the situation, the objectives,
stakes or power but also by the orientation given from the very
beginning of the relationship. When negotiation is reduced to a
confrontation of power, participants rely on coercive measures, using
different kinds of threats or make false promises and bluff in order to
establish a more acceptable balance of power.
Most of the negotiators have a tendency to complain about the
unethical aspects of the tactics used by their counterparts while, as
the same time, they are mostly unaware of the sources of influence of
their own vision and practices. In this article, our intention is to
clarify these sources and try to understand what can lead negotiators
to unethical practices.
Abstract: The effectiveness of consuming a nutrient fortified oat drink on iron, zinc, vitamin A and vitamin C status was assessed among a cohort of school-aged Filipino children. Ultimate study implementation permitted only a within-subject comparison of change in nutritional status after four months of consuming a nutrient fortified oat drink. Thirty-eight anemic children (5-8 years) consumed an oat drink fortified with iron as NaFeEDTA, zinc, vitamin A and vitamin C for 120 days. Height, weight, serum nutrient levels, anemia status and dietary intake were assessed pre and post intervention. Thirty-four anemic children completed the intervention. After 4 months of intervention, prevalence of anemia decreased by 68% and significant improvements in iron and vitamin A status were observed. Results demonstrate the effectiveness of the fortified oat drink in alleviating anemia in young children and highlight the value of fortification programs
Abstract: Because of its global reach, reduction of time
restraints, and ability to reduce costs and increase sales, use of the
Internet, the World Wide Web (WWW), and related technologies
can be a competitive tool in the arsenal of small and medium-sized
enterprises (SMEs). Countries the world over are interested in the
successful adoption of the Internet by SMEs. Because a vast
majority of jobs come from that sector, greater financial success of
SMEs translates into greater job growth and, subsequently, higher
tax revenue to the government. This research investigated the level
of Internet usage for business solutions by small and medium
enterprises in Jordan. Through the survey of a random sample of
100 firms with less than 500 employees and from data obtained
from this survey that formed the basis for our study, we found that
a majority of respondents use the Internet in business activities ,
the adoption of the Internet as a business tool is limited to a
brochure where Web site which primarily provides one way. As
such, there wasn't interactive information about the company and
its products and services.
Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: Thrombosis can be life threatening, necessitating therefore its instant treatment. Hydergine, a nootropic agent is used as a cognition enhancer in stroke patients but relatively little is known about its anti-thrombolytic effect. To investigate this aspect, in vivo and ex vivo experiments were designed and conducted. Three groups of rats were injected 1.5mg, 3.0mg and 4.5mg hydergine intraperitonealy with and without prior exposure to fresh plasma. Positive and negative controls were run in parallel. Animals were sacrificed after 1.5hrs and BT, CT, PT, INR, APTT, plasma calcium levels were estimated. For ex vivo analyses, each 1ml blood aspirated was exposed to 0.1mg, 0.2mg, 0.3mg dose of hydergine with parallel controls. Parameters analyzed were as above. Statistical analysis was through one-way ANOVA. Dunken-s and Tukey-s tests provided intra-group variance. BT, CT, PT, INR and APTT increased while calcium levels dropped significantly (P
Abstract: This work presents a numerical model developed to
simulate the dynamics and vibrations of a multistage tractor gearbox.
The effect of time varying mesh stiffness, time varying frictional
torque on the gear teeth, lateral and torsional flexibility of the shafts
and flexibility of the bearings were included in the model. The model
was developed by using the Lagrangian method, and it was applied to
study the effect of three design variables on the vibration and stress
levels on the gears. The first design variable, module, had little effect
on the vibration levels but a higher module resulted to higher bending
stress levels. The second design variable, pressure angle, had little
effect on the vibration levels, but had a strong effect on the stress
levels on the pinion of a high reduction ratio gear pair. A pressure
angle of 25o resulted to lower stress levels for a pinion with 14 teeth
than a pressure angle of 20o. The third design variable, contact ratio,
had a very strong effect on both the vibration levels and bending
stress levels. Increasing the contact ratio to 2.0 reduced both the
vibration levels and bending stress levels significantly. For the gear
train design used in this study, a module of 2.5 and contact ratio of
2.0 for the various meshes was found to yield the best combination
of low vibration levels and low bending stresses. The model can
therefore be used as a tool for obtaining the optimum gear design
parameters for a given multistage spur gear train.