Abstract: The adsorption efficiency of fired clayey pellets of 5
and 8 mm diameter size for Cu(II) and Zn(II) ion removal from a
waste printing developer was studied. In order to investigate the
influence of contact time, adsorbent mass and pellet size on the
adsorption efficiency the batch mode was carried out. Faster uptake
of copper ion was obtained with the fired clay pellets of 5 mm
diameter size within 30 minutes. The pellets of 8 mm diameter size
showed the higher equilibrium time (60 to 75 minutes) for copper and
zinc ion. The results pointed out that adsorption efficiency increases
with the increase of adsorbent mass. The maximal efficiency is
different for Cu(II) and Zn(II) ion due to the pellet size. Therefore,
the fired clay pellets of 5 mm diameter size present an effective
adsorbent for Cu(II) ion removal (adsorption efficiency is 63.6%),
whereas the fired clay pellets of 8 mm diameter size are the best
alternative for Zn(II) ion removal (adsorption efficiency is 92.8%)
from a waste printing developer.
Abstract: A parametric study on circular thin-walled pipes
subjected to pure bending is performed. Both straight and curved
pipes are considered. Ratio D/t, initial pipe curvature and internal
pressure are the parameters varying in the analyses. The study is
mainly FEA-based.
It is found that negative curvatures (opposite to bending moment)
considerably increase stiffness and buckling limit of the pipe when no
internal pressure is acting and, similarly, positive curvatures decrease
the stiffness and buckling limit. For internal pressurised pipes the
effects of initial pipe curvature are less relevant. Results show that
this phenomenon is in relationship with the cross-section deformation
due to bending moment, which undergoes relevant ovalisation for no
pressurised pipes and little ovalisation for pressurised pipes.
Abstract: The main objective of this paper is study the influence
of carbon nano-tubes fibers and nano silica fibers on the
characteristic compressive strength and flexural strength on concrete
and cement mortar. Twelve tested specimens were tested with square
section its dimensions (4040 160) mm, divided into four groups.
The first and second group studied the effect of carbon nano-tubes
(CNTs) fibers with different percentage equal to 0.0, 0.11%, 0.22%,
and 0.33% by weight of cement and effect of nano-silica (nS) fibers
with different percentages equal to 0.0, 1.0%, 2.0%, and 3.0% by
weight of cement on the cement mortar. The third and fourth groups
studied the effect of CNTs fiber with different percentage equal to
0.0%, 0.11%, and 0.22% by weight of cement, and effect of nS fibers
with different percentages were equal to 0.0%, 1.0%, and 2.0% by
weight of cement on the concrete. The compressive strength and
flexural strength at 7, 28, and 90 days is determined. From analysis of
tested results concluded that the nano-fibers is more effective when
used with cement mortar more than used with concrete because of
increasing the surface area, decreasing the pore and the collection of
nano-fibers. And also by adding nano-fibers the improvement of
flexural strength of concrete and cement mortar is more than
improvement of compressive strength.
Abstract: This paper presents a novel fractal antenna structure
proposed for UWB (Ultra – Wideband) applications. The frequency
band 3.1-10.6GHz released by FCC (Federal Communication
Commission) as the commercial operation of UWB has been chosen
as frequency range for this antenna based on coplanar waveguide
(CPW) feed and circular shapes fulfilled according to fractal
geometry. The proposed antenna is validated and designed by using
an FR4 substrate with overall area of 34x43 mm2. The simulated
results performed by CST-Microwave Studio and compared by ADS
(Advanced Design System) show good matching input impedance
with return loss less than -10dB between 2.9 GHz and 11 GHz.
Abstract: Universal modeling method well proven for industrial
compressors was applied for design of the high flow rate supersonic
stage. Results were checked by ANSYS CFX and NUMECA Fine
Turbo calculations. The impeller appeared to be very effective at
transonic flow velocities. Stator elements efficiency is acceptable at
design Mach numbers too. Their loss coefficient versus inlet flow
angle performances correlates well with Universal modeling
prediction. The impeller demonstrates ability of satisfactory operation
at design flow rate. Supersonic flow behavior in the impeller inducer
at the shroud blade to blade surface Φ des deserves additional study.
Abstract: There is an evident trend to elevate pressure ratio of a
single stage of a turbo compressors - axial compressors in particular.
Whilst there was an opinion recently that a pressure ratio 1,9 was a
reasonable limit, later appeared information on successful modeling
tested of stages with pressure ratio up to 2,8. The authors recon that
lack of information on high pressure stages makes actual a study of
rational choice of design parameters before high supersonic flow
problems solving. The computer program of an engineering type was
developed. Below is presented a sample of its application to study
possible parameters of the impeller of the stage with pressure ratio
3,0. Influence of two main design parameters on expected efficiency,
periphery blade speed and flow structure is demonstrated. The results
had lead to choose a variant for further analysis and improvement by
CFD methods.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.
Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: Job Scheduling plays an important role for efficient
utilization of grid resources available across different domains and
geographical zones. Scheduling of jobs is challenging and NPcomplete.
Evolutionary / Swarm Intelligence algorithms have been
extensively used to address the NP problem in grid scheduling.
Artificial Bee Colony (ABC) has been proposed for optimization
problems based on foraging behaviour of bees. This work proposes a
modified ABC algorithm, Cluster Heterogeneous Earliest First Min-
Min Artificial Bee Colony (CHMM-ABC), to optimally schedule
jobs for the available resources. The proposed model utilizes a novel
Heterogeneous Earliest Finish Time (HEFT) Heuristic Algorithm
along with Min-Min algorithm to identify the initial food source.
Simulation results show the performance improvement of the
proposed algorithm over other swarm intelligence techniques.
Abstract: The prepreg process among the CFRP (Carbon Fiber
Reinforced Plastic) forming methods is the short term of
‘Pre-impregnation’, which is widely used for aerospace composites
that require a high quality property such as a fiber-reinforced woven
fabric, in which an epoxy hardening resin is impregnated the reality.
However, that this process requires continuous researches and
developments for its commercialization because the delamination
characteristically develops between the layers when a great weight is
loaded from outside to supplement such demerit, three lamination
methods among the prepreg lamination methods of CFRP were
designed to minimize the delamination between the layers due to
external impacts. Further, the newly designed methods and the
existing lamination methods were analyzed through a mechanical
characteristic test, Interlaminar Shear Strength test. The Interlaminar
Shear Strength test result confirmed that the newly proposed three
lamination methods, i.e. the Roll, Half and Zigzag laminations,
presented more excellent strengths compared to the conventional Ply
lamination. The interlaminar shear strength in the roll method with
relatively dense fiber distribution was approximately 1.75% higher
than that in the existing ply lamination method, and in the half method,
it was approximately 0.78% higher.
Abstract: In this paper, the electromagnetic shielding
characteristics of an up-to-date typical carbon filler material, carbon
fiber used with a metal mesh were investigated. Carbon fiber
12k-prepregs, where carbon fibers were impregnated with epoxy, were
laminated with wire meshes, vacuum bag-molded and hardened to
manufacture hybrid-type specimens, with which an electromagnetic
shield test was performed in accordance with ASTM D4935-10,
through which was known as the most excellent reproducibility is
obtainable among electromagnetic shield tests. In addition, glass fiber
prepregs whose electromagnetic shielding effect were known as
insignificant were laminated and formed with wire meshes to verify
the validity of the electromagnetic shield effect of wire meshes in
order to confirm the electromagnetic shielding effect of metal meshes
corresponding existing carbon fiber 12k-prepregs. By grafting carbon
fibers, on which studies are being actively underway in the
environmental aspects and electromagnetic shielding effect, with
hybrid-type wire meshes that were analysed through the tests, in this
study, the applicability and possibility are proposed.
Abstract: This study examines several critical dimensions of eservice
quality overlooked in the existing literature and proposes a
model and instrument framework for measuring customer perceived
e-service quality in the banking sector. The initial design was derived
from a pool of instrument dimensions and their items from the
existing literature review by content analysis. Based on focused
group discussion, nine dimensions were extracted. An exploratory
factor analysis approach was applied to data from a survey of 323
respondents. The instrument has been designed specifically for the
banking sector. Research data was collected from bank customers
who use electronic banking in a developing economy. A nine-factor
instrument has been proposed to measure the e-service quality. The
instrument has been checked for reliability. The validity and sample
place limited the applicability of the instrument across economies and
service categories. Future research must be conducted to check the
validity. This instrument can help bankers in developing economies
like India to measure the e-service quality and make improvements.
The present study offers a systematic procedure that provides insights
on to the conceptual and empirical comprehension of customer
perceived e-service quality and its constituents.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: This research study is an exploration of the selfdirected
professional development of teachers who teach in public
schools in an era of democracy and educational change in South
Africa. Amidst an ever-changing educational system, the teachers in
this study position themselves as self-directed teacher-learners where
they adopt particular learning practices which enable change within
the broader discourses of public schooling. Life-story interviews
were used to enter into the private and public spaces of five teachers
which offer glimpses of how particular systems shaped their
identities, and how the meanings of self-directed teacher-learner
shaped their learning practices. Through the Multidimensional
Framework of Analysis and Interpretation the teachers’ stories were
analysed through three lenses: restorying the field texts - the self
through story; the teacher-learner in relation to social contexts, and
practices of self-directed learning. This study shows that as teacherlearners
learn for change through self-directed learning practices,
they develop their agency as transformative intellectuals, which is
necessary for the reworking of South African public schools.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: A model reference adaptive control and a fixed gain
LQR control were implemented in the height controller of a quadrotor
that has parametric uncertainties due to the act of picking up an
object of unknown dimension and mass. It is shown that an adaptive
controller, unlike the fixed gain controller, is capable of ensuring a
stable tracking performance under such condition, although adaptive
control suffers from several limitations. The combination of both
adaptive and fixed gain control in the controller architecture can
result in an enhanced tracking performance in the presence parametric
uncertainties.
Abstract: In this paper a real-time obstacle avoidance approach
for both autonomous and non-autonomous dynamical systems (DS) is
presented. In this approach the original dynamics of the controller
which allow us to determine safety margin can be modulated.
Different common types of DS increase the robot’s reactiveness in
the face of uncertainty in the localization of the obstacle especially
when robot moves very fast in changeable complex environments.
The method is validated by simulation and influence of different
autonomous and non-autonomous DS such as important
characteristics of limit cycles and unstable DS. Furthermore, the
position of different obstacles in complex environment is explained.
Finally, the verification of avoidance trajectories is described through
different parameters such as safety factor.
Abstract: Background and aim: It has not been well studied
whether fentanyl-thiopental (FT) is effective and safe for PSA in
orthopedic procedures in Emergency Department (ED). The aim of
this trial was to evaluate the effectiveness of intravenous FT versus
fentanyl-midazolam (FM) in patients who suffered from shoulder
dislocation or distal radial fracture-dislocation.
Methods: In this randomized double-blinded study, Seventy-six
eligible patients were entered the study and randomly received
intravenous FT or FM. The success rate, onset of action and recovery
time, pain score, physicians’ satisfaction and adverse events were
assessed and recorded by treating emergency physicians. The
statistical analysis was intention to treat.
Results: The success rate after administrating loading dose in FT
group was significantly higher than FM group (71.7% vs. 48.9%,
p=0.04); however, the ultimate unsuccessful rate after 3 doses of
drugs in the FT group was higher than the FM group (3 to 1) but it
did not reach to significant level (p=0.61). Despite near equal onset
of action time in two study group (P=0.464), the recovery period in
patients receiving FT was markedly shorter than FM group
(P
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.