Abstract: Characterized as rich mineral substances, low
temperature, few bacteria, and stability with numerous implementation
aspects on aquaculture, food, drinking, and leisure, the deep sea water
(DSW) development has become a new industry in the world. It has
been report that marine algae contain various biologically active
compounds. This research focued on the affections in cultivating
Sagrassum cristaefolium with different concentration of deep sea
water(DSW) and surface sea water(SSW). After two and four weeks,
the total phenolic contents were compared in Sagrassum cristaefolium
culturing with different ways, and the reductive activity of them was
also be tried with potassium ferricyanide. Those fresh seaweeds were
dried with oven and were ground to powder. Progressively, the marine
algae we cultured was extracted by water under the condition with
heating them at 90Ôäâ for 1hr.The total phenolic contents were be
executed using Folin–Ciocalteu method. The results were explaining
as follows: the highest total phenolic contents and the best reductive
ability of all could be observed on the 1/4 proportion of DSW to SSW
culturing in two weeks. Furthermore, the 1/2 proportion of DSW to
SSW also showed good reductive ability and plentiful phenolic
compositions. Finally, we confirmed that difference proportion of
DSW and SSW is the major point relating to ether the total phenolic
components or the reductive ability in the Sagrassum cristaefolium. In
the future, we will use this way to mass production the marine algae or
other micro algae on industry applications.
Abstract: An electronic portal image device (EPID) has become
a method of patient-specific IMRT dose verification for radiotherapy.
Research studies have focused on pre and post-treatment verification,
however, there are currently no interventional procedures using EPID
dosimetry that measure the dose in real time as a mechanism to
ensure that overdoses do not occur and underdoses are detected as
soon as is practically possible. As a result, an EPID-based real time
dose verification system for dynamic IMRT was developed and was
implemented with MATLAB/Simulink. The EPID image acquisition
was set to continuous acquisition mode at 1.4 images per second. The
system defined the time constraint gap, or execution gap at the image
acquisition time, so that every calculation must be completed before
the next image capture is completed. In addition, the
Abstract: Tourism is a phenomenon respected by the human communities since a long time ago. It has been evoloving continually based on a variety of social and economic needs and with respect to increasingly development of communication and considerable increase of tourist-s number and resulted exchange income has attained much out come such as employment for the communities. or the purpose of tourism development in this zone suitable times and locations need to be specified in the zone for the tourist-s attendance. One of the most important needs of the tourists is the knowledge of climate conditions and suitable times for sightseeing. In this survey, the climate trend condition has been identified for attending the tourists in Isfahan province using the modified tourism climate index (TCI) as well as SPSS, GIS, excel, surfer softwares. This index evoluates systematically the climate conditions for tourism affairs and activities using the monthly maximum mean parameters of daily temperature, daily mean temperature, minimum relative humidity, daily mean relative humidity, precipitation (mm), total sunny hours, wind speed and dust. The results obtaind using kendal-s correlation test show that the months January, February, March, April, May, June, July, August, September, October, November and December are significant and have an increasing trend that indicates the best condition for attending the tourists. S, P, T mean , T max and dust are estimated from 1976-2005 and do kendal-s correlation test again to see which parameter has been effective. Based on the test, we also observed on the effective parameters that the rate of dust in February, March, April, May, June, July, August, October and November is decreasing and precipitation in September and January is increasing and also the radiation rate in May and August is increasing that indicate a better condition of convenience. Maximum temperature in June is also decreasing. Isfahan province has two spring and fall peaks and the best places for tourism are in the north and western areas.
Abstract: Health problems linked to urban growth are current
major concerns of developing countries. In 2002 and 2005, an
interdisciplinary program “Populations et Espaces ├á Risques
SANitaires" (PERSAN) was set up under the patronage of the
Development and Research Institute. Centered on health in
Cameroon-s urban environment, the program mainly sought to (i)
identify diarrhoea risk factors in Yaoundé, (ii) to measure their
prevalence and apprehend their spatial distribution. The crosssectional
epidemiological study that was carried out revealed a
diarrheic prevalence of 14.4% (437 cases of diarrhoea on the 3,034
children examined). Also, among risk factors studied, household
refuse management methods used by city dwellers were statistically
associated to these diarrhoeas. Moreover, it happened that levels of
diarrhoeal attacks varied consistently from one neighbourhood to
another because of the discrepancy urbanization process of the
Yaoundé metropolis.
Abstract: Green- spaces might be very attractive, but
where are the economic benefits? What value do nature and
landscape have for us? What difference will it make to jobs,
health and the economic strength of areas struggling with
deprivation and social problems? [1].There is a need to consider
green spaces from a different perspective. Green planning is not just
about flora and fauna, but also about planning for economic benefits
[2]. It is worth trying to quantify the value of green spaces since
nature and landscape are crucially important to our quality of life and
sustainable development. The reality, however, is that urban
development often takes place at the expense of green spaces.
Urbanization is an ongoing process throughout the world; however,
hyper-urbanization without environmental planning is destructive,
not constructive [3]. Urban spaces are believed to be more valuable
than other land uses, particular green areas, simply because of the
market value connected to urban spaces. However, attractive
landscapes can help raise the quality and value of the urban market
even more. In order to reach these objectives of integrated planning,
the Green-Value-Gap needs to be bridged. Economists have to
understand the concept of Green-Planning and the spinoffs, and
Environmentalists have to understand the importance of urban
economic development and the benefits thereof to green planning. An
interface between Environmental Management, Economic
Development and sustainable Spatial Planning are needed to bridge
the Green-Value-Gap.
Abstract: There are little subjects in macroeconomics that are so
widely discussed, but at the same time controversial and without a
clear solution such as the choice of exchange rate regime. National
authorities need to take into consideration numerous fundamentals,
trying to fulfil goals of economic growth, low and stable inflation
and international stability. This paper focuses on the countries of ex-
Yugoslavia and their exchange rate history as independent states. We
follow the development of the regimes in 6 countries during the
transition through the financial crisis of the second part of the 2000s
to the prospects of their final goal: full membership in the European
Union. Main question is to what extent has the exchange regime
contributed to their economic success, considering other objective
factors.
Abstract: This paper describes the designs of a first and second
generation autonomous gas monitoring system and the successful
field trial of the final system (2nd generation). Infrared sensing
technology is used to detect and measure the greenhouse gases
methane (CH4) and carbon dioxide (CO2) at point sources. The
ability to monitor real-time events is further enhanced through the
implementation of both GSM and Bluetooth technologies to
communicate these data in real-time. These systems are robust,
reliable and a necessary tool where the monitoring of gas events in
real-time are needed.
Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: The result of process of territory-s development is the territory-s state of development (TSoD), which is pointed towards the provision and improvement of people-s life conditions. The authors offer to measure the TSoD according to their own developed model. Using the available statistical data regarding the values of model-s elements, the authors empirically show which element mainly determines the TSoD. The findings of the research showed that the key elements of the TSoD are the “Material welfare of people" and “People-s health". Performing a deeper statistical analysis of correlation between these elements, it turned out that it is not so necessary for a country to be bent on trying to increase the material growth of a territory, because a relatively high index of life expectancy at birth could be ensured also by much more modest material resources. On the other hand, the economical feedback of longer lifespan within countries with lower material performance is also relatively low.
Abstract: Rural areas of Tanzania are still disadvantaged in terms of diffusion of IP-based services; this is due to lack of Information and Communication Technology (ICT) infrastructures, especially lack of connectivity. One of the limitations for connectivity problems in rural areas of Tanzania is the high cost to establish infrastructures for IP-based services [1-2]. However the cost of connectivity varies from one technology to the other and at the same time, the cost is also different from one operator (service provider) to another within the country. This paper presents development of software system to calculate cost of connectivity to rural areas of Tanzania. The system is developed to make an easy access of connectivity cost from different technologies and different operators. The development of the calculator follows the V-model software development lifecycle. The calculator is used to evaluate the economic viability of different technologies considered as being potential candidates to provide rural connectivity. In this paper, the evaluation is based on the techno-economic analysis approach.
Abstract: Resistance of denial of service attacks is a key security requirement in voting protocols. Acquisti protocol plays an important role in development of internet voting protocols and claims its security without strong physical assumptions. In this study firstly Acquisti protocol is modeled in extended applied pi calculus, and then resistance of denial of service attacks is proved with ProVerif. The result is that it is not resistance of denial of service attacks because two denial of service attacks are found. Finally we give the method against the denial of service attacks.
Abstract: Natural ventilation has played an important role for
many low energy-building designs. It has been also noticed as a
essential subject to persistently bring the fresh cool air from the
outside into a building. This study carried out the computational fluid
dynamics (CFD)-based simulations to examine the natural ventilation
development of a work area in a public building. The simulated results
can be useful to better understand the indoor microclimate and the
interaction of wind with buildings. Besides, this CFD simulation
procedure can serve as an effective analysis tool to characterize the
airing performance, and thereby optimize the building ventilation for
strengthening the architects, planners and other decision makers on
improving the natural ventilation design of public buildings.
Abstract: This paper focuses on the calibration problem of a
multi-view shooting system designed for the production of 3D
content for auto-stereoscopic visualization. The considered multiview
camera is characterized by coplanar and decentered image
sensors regarding to the corresponding optical axis. Based on the
Faugéras and Toscani-s calibration approach, a calibration method is
herein proposed for the case of multi-view camera with parallel and
decentered image sensors. At first, the geometrical model of the
shooting system is recalled and some industrial prototypes with some
shooting simulations are presented. Next, the development of the
proposed calibration method is detailed. Finally, some simulation
results are presented before ending with some conclusions about this
work.
Abstract: In this work, stationary hot-wire measurements are
carried out to investigate the characteristics of a round free jet in its
potential core region (0 ≤ x/d ≤ 10). Measurements are carried out on
an incompressible round jet for a range of Reynolds numbers from
4000 to 8000, calculated based on the jet exit mean velocity and the
nozzle diameter. The effect of flow velocity on the development
characteristics of the jet in the core region is analyzed. Timeaveraged
statistics, spectra of velocity and its higher order moments
are presented and explained.
Abstract: The rate of production of main products of the Fischer-Tropsch reactions over Fe/HZSM5 bifunctional catalyst in a fixed bed reactor is investigated at a broad range of temperature, pressure, space velocity, H2/CO feed molar ratio and CO2, CH4 and water flow rates. Model discrimination and parameter estimation were performed according to the integral method of kinetic analysis. Due to lack of mechanism development for Fisher – Tropsch Synthesis on bifunctional catalysts, 26 different models were tested and the best model is selected. Comprehensive one and two dimensional heterogeneous reactor models are developed to simulate the performance of fixed-bed Fischer – Tropsch reactors. To reduce computational time for optimization purposes, an Artificial Feed Forward Neural Network (AFFNN) has been used to describe intra particle mass and heat transfer diffusion in the catalyst pellet. It is seen that products' reaction rates have direct relation with H2 partial pressure and reverse relation with CO partial pressure. The results show that the hybrid model has good agreement with rigorous mechanistic model, favoring that the hybrid model is about 25-30 times faster.
Abstract: The daily increase of organic waste materials resulting
from different activities in the country is one of the main factors for
the pollution of environment. Today, with regard to the low level of
the output of using traditional methods, the high cost of disposal
waste materials and environmental pollutions, the use of modern
methods such as anaerobic digestion for the production of biogas has
been prevailing. The collected biogas from the process of anaerobic
digestion, as a renewable energy source similar to natural gas but
with a less methane and heating value is usable. Today, with the help
of technologies of filtration and proper preparation, access to biogas
with features fully similar to natural gas has become possible. At
present biogas is one of the main sources of supplying electrical and
thermal energy and also an appropriate option to be used in four
stroke engine, diesel engine, sterling engine, gas turbine, gas micro
turbine and fuel cell to produce electricity. The use of biogas for
different reasons which returns to socio-economic and environmental
advantages has been noticed in CHP for the production of energy in
the world. The production of biogas from the technology of anaerobic
digestion and its application in CHP power plants in Iran can not only
supply part of the energy demands in the country, but it can
materialize moving in line with the sustainable development. In this
article, the necessity of the development of CHP plants with biogas
fuels in the country will be dealt based on studies performed from the
economic, environmental and social aspects. Also to prove the
importance of the establishment of these kinds of power plants from
the economic point of view, necessary calculations has been done as
a case study for a CHP power plant with a biogas fuel.
Abstract: Software crisis refers to the situation in which the developers are not able to complete the projects within time and budget constraints and moreover these overscheduled and over budget projects are of low quality as well. Several methodologies have been adopted form time to time to overcome this situation and now in the focus is component based software engineering. In this approach, emphasis is on reuse of already existing software artifacts. But the results can not be achieved just by preaching the principles; they need to be practiced as well. This paper highlights some of the very basic elements of this approach, which has to be in place to get the desired goals of high quality, low cost with shorter time-to-market software products.
Abstract: Nowadays, the rapid development of multimedia
and internet allows for wide distribution of digital media data.
It becomes much easier to edit, modify and duplicate digital
information Besides that, digital documents are also easy to
copy and distribute, therefore it will be faced by many
threatens. It-s a big security and privacy issue with the large
flood of information and the development of the digital
format, it become necessary to find appropriate protection
because of the significance, accuracy and sensitivity of the
information. Nowadays protection system classified with more
specific as hiding information, encryption information, and
combination between hiding and encryption to increase information
security, the strength of the information hiding science is due to the
non-existence of standard algorithms to be used in hiding secret
messages. Also there is randomness in hiding methods such as
combining several media (covers) with different methods to pass a
secret message. In addition, there are no formal methods to be
followed to discover the hidden data. For this reason, the task of this
research becomes difficult. In this paper, a new system of information
hiding is presented. The proposed system aim to hidden information
(data file) in any execution file (EXE) and to detect the hidden file
and we will see implementation of steganography system which
embeds information in an execution file. (EXE) files have been
investigated. The system tries to find a solution to the size of the
cover file and making it undetectable by anti-virus software. The
system includes two main functions; first is the hiding of the
information in a Portable Executable File (EXE), through the
execution of four process (specify the cover file, specify the
information file, encryption of the information, and hiding the
information) and the second function is the extraction of the hiding
information through three process (specify the steno file, extract the
information, and decryption of the information). The system has
achieved the main goals, such as make the relation of the size of the
cover file and the size of information independent and the result file
does not make any conflict with anti-virus software.
Abstract: The world is moving rapidly toward the deployment
of information and communication systems. Nowadays, computing
systems with their fast growth are found everywhere and one of the main challenges for these systems is increasing attacks and security threats against them. Thus, capturing, analyzing and verifying security requirements becomes a very important activity in
development process of computing systems, specially in developing
systems such as banking, military and e-business systems. For
developing every system, a process model which includes a process,
methods and tools is chosen. The Rational Unified Process (RUP) is
one of the most popular and complete process models which is used
by developers in recent years. This process model should be extended to be used in developing secure software systems. In this
paper, the Requirement Discipline of RUP is extended to improve RUP for developing secure software systems. These proposed extensions are adding and integrating a number of Activities, Roles,
and Artifacts to RUP in order to capture, document and model threats
and security requirements of system. These extensions introduce a
group of clear and stepwise activities to developers. By following these activities, developers assure that security requirements are
captured and modeled. These models are used in design, implementation and test activitie
Abstract: Knowledge capabilities are increasingly important for
the innovative technology enterprises to enhance the business
performance in terms of product competitiveness, innovation and
sales. Recognition of the company capability by auditing allows them
to further pursue advancement, strategic planning and hence gain
competitive advantages. This paper attempts to develop an
Organizations- Knowledge Capabilities Assessment (OKCA) method
to assess the knowledge capabilities of technology companies. The
OKCA is a questionnaire-based assessment tool which has been
developed to uncover the impact of various knowledge capabilities on
different organizational performance. The collected data is then
analyzed to find out the crucial elements for different technological
companies. Based on the results, innovative technology enterprises are
able to recognize the direction for further improvement on business
performance and future development plan. External environmental
factors affecting organization performance can be found through the
further analysis of some selected reference companies.