Abstract: The nanofiber sheet of Multiwall Cabon Nanotube
(MWCNTs)/Polyacylonitile (PAN) composites was fabricated from
electrospun nanofiber. Firstly the surface of MWCNTs was
chemically modified, comparing two different techniques consisting
of admicellar polymerization and functionalization to improve the
dispersion and prevent the aggregation in the PAN matrix. The
modified MWCNTs were characterized by the dispersion in
dimethylformamide (DMF) solvent, Laser particle size, and FTRaman.
Lastly, DSC, SEM and mechanical properties of the
nanofiber sheet were examined. The results show that the mechanical
properties of the nanofiber sheet prepared from admicellar
polymerization-modified MWCNTs were higher than those of the
others.
Abstract: Effective cooling of electronic equipment has emerged
as a challenging and constraining problem of the new century. In the
present work the feasibility and effectiveness of jet impingement
cooling on electronics were investigated numerically and
experimentally. Studies have been conducted to see the effect of the
geometrical parameters such as jet diameter (D), jet to target
spacing (Z) and ratio of jet spacing to jet diameter (Z/D) on the heat
transfer characteristics. The values of Reynolds numbers considered
are in the range 7000 to 42000. The results obtained from the
numerical studies are validated by conducting experiments. From the
studies it is found that the optimum value of Z/D ratio is 5. For a
given Reynolds number, the Nusselt number increases by about 28%
if the diameter of the nozzle is increased from 1mm to 2mm.
Correlations are proposed for Nusselt number in terms of Reynolds
number and these are valid for air as the cooling medium.
Abstract: The aims of this paper are to study the efficacy of
chitosan nanoparticles in stimulating specific antibody against
A/H1N1 influenza antigen in mice. Chitosan nanoparticles (CSN)
were characterized by TEM. The results showed that the average size
of CSN was from 80nm to 106nm. The efficacy of A/H1N1 influenza
vaccine loaded on the surface of CSN showed that loading efficiency
of A/H1N1 influenza antigen on CSN was from 93.75 to 100%. Safe
property of the vaccine were tested. In 10 days post vaccination,
group of CSN 30 kDa and 300 kDa loaded A/H1N1 influenza antigen
were the rate of immune response on mice to be 100% (9/9) higher
than Al(OH)3 and other adjuvant. 100% mice in the experiment of all
groups had immune response in 20 days post vaccination. The results
also showed that HI titer of the group using CSN 300 kDa as an
adjuvant increased significantly up to 3971 HIU, over three-fold
higher than the Al(OH)3 adjuvant, chitosan (CS), and one hundredfold
than the A/H1N1 antigen only. Stability of the vaccine
formulation was investigated.
Abstract: We estimate snow velocity and snow drift density on hilly terrain under the assumption that the drifting snow mass can be represented using a micro-continuum approach (i.e. using a nonclassical mechanics approach assuming a class of fluids for which basic equations of mass, momentum and energy have been derived). In our model, the theory of coupled stress fluids proposed by Stokes [1] has been employed for the computation of flow parameters. Analyses of bulk drift velocity, drift density, drift transport and mass transport of snow particles have been carried out and computations made, considering various parametric effects. Results are compared with those of classical mechanics (logarithmic wind profile). The results indicate that particle size affects the flow characteristics significantly.
Abstract: Phase locked loops (PLL) and delay locked loops (DLL) play an important role in establishing coherent references (phase of carrier and symbol timing) in digital communication systems. Fully digital receiver including digital carrier synchronizer and symbol timing synchronizer fulfils the conditions for universal multi-mode communication receiver with option of symbol rate setting over several digit places and long-term stability of requirement parameters. Afterwards it is necessary to realize PLL and DLL in synchronizer in digital form and to approach to these subsystems as a discrete representation of analog template. Analysis of discrete phase locked loop (DPLL) or discrete delay locked loop (DDLL) and technique to determine their characteristics based on analog (continuous-time) template is performed in this posed paper. There are derived transmission response and error function for 1st order discrete locked loop and resulting equations and graphical representations for 2nd order one. It is shown that the spectrum translation due to sampling takes effect at frequency characteristics computing for specific values of loop parameters.
Abstract: In this work we develop an object extraction method
and propose efficient algorithms for object motion characterization.
The set of proposed tools serves as a basis for development of objectbased
functionalities for manipulation of video content. The
estimators by different algorithms are compared in terms of quality
and performance and tested on real video sequences. The proposed
method will be useful for the latest standards of encoding and
description of multimedia content – MPEG4 and MPEG7.
Abstract: Located within the tropical belt region, there are
certain rules which should implemented in creating a passive
sustainable housing design in Malaysia. Traditional Malay house
possess a strong character with certain special spaces to create a
sustainable house which suit to the tropical climate in Malaysia. One
of the special space known as verandah or serambi gantung, create
various advantages in solving various issues. However, this special
space is not extremely being applied currently which produce major
issues in term of social and environmental aspects. Hence, this
phenomena create a negative impact to the occupant while Malaysia
already has a best housing design previously. Therefore, this paper
aims to explore both of the main issues mentioned above and reveal
the advantages of implementing verandah into passive sustainable
housing design in Malaysia. A systematic literature review is the
main methodology in this research to identify the various advantages
about verandah.. The study reveals that verandah is the best solution
in term of social and environmental issues and should be
implemented in current housing design in Malaysia.
Abstract: The mechanical properties including flexural and
tensile of neat vinyl ester and polymer based on layered silicate
nanocomposite materials are discussed. The addition of layered
silicate into the polymer matrix increased the tensile and flexural
modulus up to 1 wt.% clay loading. The incorporation of more clay
resulted in decreasing the mechanical properties which was traced to
the existence of aggregation layers. Likewise, up to 1 wt.% clay
loading, the thermal behaviour showed significant improvements and
at higher clay loading the thermal pattern was reduced. The
aggregation layers imparted a negative impact on the overall
mechanical and thermal properties. Wide Angle X-ray Diffraction,
Scanning Electron Microscopy and Transmission Electron
Microscopy were utilised in order to characterise the interlamellar
structure of nanocomposites.
Abstract: In many industries, control charts is one of the most
frequently used tools for quality management. Hotelling-s T2 is used
widely in multivariate control chart. However, it has little defect when
detecting small or medium process shifts. The use of supplementary
sensitizing rules can improve the performance of detection. This study
applied sensitizing rules for Hotelling-s T2 control chart to improve the
performance of detection. Support vector machines (SVM) classifier
to identify the characteristic or group of characteristics that are
responsible for the signal and to classify the magnitude of the mean
shifts. The experimental results demonstrate that the support vector
machines (SVM) classifier can effectively identify the characteristic
or group of characteristics that caused the process mean shifts and the
magnitude of the shifts.
Abstract: Process-oriented software development is a new
software development paradigm in which software design is modeled
by a business process which is in turn translated into a process
execution language for execution. The building blocks of this
paradigm are software units that are composed together to work
according to the flow of the business process. This new paradigm
still exhibits the characteristic of the applications built with the
traditional software component technology. This paper discusses an
approach to apply a traditional technique for software component
fabrication to the design of process-oriented software units, called
process components. These process components result from
decomposing a business process of a particular application domain
into subprocesses, and these process components can be reused to
design the business processes of other application domains. The
decomposition considers five managerial goals, namely cost
effectiveness, ease of assembly, customization, reusability, and
maintainability. The paper presents how to design or decompose
process components from a business process model and measure
some technical features of the design that would affect the
managerial goals. A comparison between the measurement values
from different designs can tell which process component design is
more appropriate for the managerial goals that have been set. The
proposed approach can be applied in Web Services environment
which accommodates process-oriented software development.
Abstract: The threshold voltage and capacitance voltage characteristics of ultra-thin Silicon-on-Insulator MOSFET are greatly influenced by the thickness and doping concentration of the silicon film. In this work, the capacitance voltage characteristics and threshold voltage of the device have been analyzed with quantum mechanical effects using the Self-Consistent model. Reduction of channel thickness and adding doping impurities cause an increase in the threshold voltage. Moreover, the temperature effects cause a significant amount of threshold voltage shift. The temperature dependence of threshold voltage has also been observed with Self- Consistent approach which are well supported from experimental performance of practical devices.
Abstract: The analytical solution of functionally graded
piezoelectric hollow cylinder which is under radial electric potential
and non-axisymmetric thermo-mechanical loads, are presented in this
paper. Using complex Fourier series and estimation of power law for
variations of material characterizations through the thickness, the
electro thermo mechanical behavior of the FGPM cylinder is
obtained. The stress and displacement distributions and the effect of
electric potential field on the cylinder behavior are also presented and
some applicable results are offered at the end of the paper.
Abstract: The rapid urbanization of cities has a bane in the form
road accidents that cause extensive damage to life and limbs. A
number of location based factors are enablers of road accidents in the
city. The speed of travel of vehicles is non-uniform among locations
within a city. In this study, the perception of vehicle users is captured
on a 10-point rating scale regarding the degree of variation in speed
of travel at chosen locations in the city. The average rating is used to
cluster locations using fuzzy c-means clustering and classify them as
low, moderate and high speed of travel locations. The high speed of
travel locations can be classified proactively to ensure that accidents
do not occur due to the speeding of vehicles at such locations. The
advantage of fuzzy c-means clustering is that a location may be a
part of more than one cluster to a varying degree and this gives a
better picture about the location with respect to the characteristic
(speed of travel) being studied.
Abstract: In the present paper, disc loaded interaction structure
for potential application in wideband Gyro-TWT amplifier has been
analyzed, taking all the space and modal harmonics into
consideration, for the eigenwave solutions. The analysis has been
restricted to azimuthally symmetric TE0,n mode. Dispersion
characteristics have been plotted by varying the structure parameters
and have been validated against HFSS simulation results. The
variation of eigenvalue with respect to different structure parameters
has also been presented. It has been observed that disc periodicity
plays very important role for wideband operation of disc-loaded
Gyro-TWT.
Abstract: An empirical linearly-hyperbolic approximation of the I - V characteristic of a solar cell is presented. This approximation is based on hyperbolic dependence of a current of p-n junctions on voltage for large currents. Such empirical approximation is compared with the early proposed formal linearly-hyperbolic approximation of a solar cell. The expressions defining laws of change of parameters of formal approximation at change of a photo current of family of characteristics are received. It allows simplifying a finding of parameters of approximation on actual curves, to specify their values. Analytical calculation of load regime for linearly - hyperbolic model leads to quadratic equation. Also, this model allows to define soundly a deviation from the maximum power regime and to compare efficiency of regimes of solar cells with different parameters.
Abstract: The habitat where the present study has been carried
out is productive in relation to nutrient quality and they may perform
several useful functions, but are also threatened for their existence.
Hence, the proposed work, will add much new information about
biodiversity of macrophytes in drains and their embankment. All the
species were identified with their different stages of growth which
encountered on the three selected sites (I, II and III). The number of
species occurring at each site is grouped seasonally, i.e. summer,
rainy and winter season and the species were further recorded for the
study of phytosociology. Phytosociological characters such as
frequency, density and abundance were influenced by the climatic,
anthropogenic and biotic stresses prevailing at the three study sites.
All the species present at the study sites have shown maximum
values of frequency, density and abundance in rainy season in
comparison to that of summer and winter seasons.
Abstract: In working mode some unexpected changes could
be arise in inner structure of electromagnetic device. They
influence modification in electromagnetic field propagation map.
The field values at an observed boundary are also changed. The
development of the process has to be watched because the arising
structural changes would provoke the device to be gone out later.
The probabilistic assessment of the state is possible to be made.
The numerical assessment points if the resulting changes have
only accidental character or they are due to the essential inner
structural disturbances.
The presented application example is referring to the 200MW
turbine-generator. A part of the stator core end teeth zone is
simulated broken. Quasi three-dimensional electromagnetic and
temperature field are solved applying FEM. The stator core state
diagnosis is proposed to be solved as an identification problem on
the basis of a statistical criterion.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: In current common research reports, salient regions
are usually defined as those regions that could present the main
meaningful or semantic contents. However, there are no uniform
saliency metrics that could describe the saliency of implicit image
regions. Most common metrics take those regions as salient regions,
which have many abrupt changes or some unpredictable
characteristics. But, this metric will fail to detect those salient useful
regions with flat textures. In fact, according to human semantic
perceptions, color and texture distinctions are the main characteristics
that could distinct different regions. Thus, we present a novel saliency
metric coupled with color and texture features, and its corresponding
salient region extraction methods. In order to evaluate the
corresponding saliency values of implicit regions in one image, three
main colors and multi-resolution Gabor features are respectively used
for color and texture features. For each region, its saliency value is
actually to evaluate the total sum of its Euclidean distances for other
regions in the color and texture spaces. A special synthesized image
and several practical images with main salient regions are used to
evaluate the performance of the proposed saliency metric and other
several common metrics, i.e., scale saliency, wavelet transform
modulus maxima point density, and important index based metrics.
Experiment results verified that the proposed saliency metric could
achieve more robust performance than those common saliency
metrics.