Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetically and thermal stresses remain major failures
for insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: This paper presents the review of past studies
concerning mathematical models for rescheduling passenger railway
services, as part of delay management in the occurrence of railway
disruption. Many past mathematical models highlighted were aimed
at minimizing the service delays experienced by passengers during
service disruptions. Integer programming (IP) and mixed-integer
programming (MIP) models are critically discussed, focusing on the
model approach, decision variables, sets and parameters. Some of
them have been tested on real-life data of railway companies
worldwide, while a few have been validated on fictive data. Based
on selected literatures on train rescheduling, this paper is able to
assist researchers in the model formulation by providing
comprehensive analyses towards the model building. These analyses
would be able to help in the development of new approaches in
rescheduling strategies or perhaps to enhance the existing
rescheduling models and make them more powerful or more
applicable with shorter computing time.
Abstract: This paper addresses the problems encountered by conventional distance relays when protecting double-circuit transmission lines. The problems arise principally as a result of the mutual coupling between the two circuits under different fault conditions; this mutual coupling is highly nonlinear in nature. An adaptive protection scheme is proposed for such lines based on application of artificial neural network (ANN). ANN has the ability to classify the nonlinear relationship between measured signals by identifying different patterns of the associated signals. One of the key points of the present work is that only current signals measured at local end have been used to detect and classify the faults in the double circuit transmission line with double end infeed. The adaptive protection scheme is tested under a specific fault type, but varying fault location, fault resistance, fault inception angle and with remote end infeed. An improved performance is experienced once the neural network is trained adequately, which performs precisely when faced with different system parameters and conditions. The entire test results clearly show that the fault is detected and classified within a quarter cycle; thus the proposed adaptive protection technique is well suited for double circuit transmission line fault detection & classification. Results of performance studies show that the proposed neural network-based module can improve the performance of conventional fault selection algorithms.
Abstract: An innovative approach utilizing highly alkaline oil
shale waste ash and carbon dioxide gas (CO2), associated with power
production, as a resource for production of precipitated calcium
carbonate (PCC) is introduced in this paper. The specifics and
feasibility of the integrated ash valorization and CO2 sequestration
process by indirect aqueous carbonation of lime-consisting ash were
elaborated and the main parameters established. Detailed description
of the formed precipitates was included. Complimentary carbonation
experiments with commercial CaO fine powder were conducted for
comparative characterization of the final products obtained on the
basis of two different raw materials. Finally, the expected CO2
uptake was evaluated.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: In the present communication, we have proposed
some new generalized measure of fuzzy entropy based upon real
parameters, discussed their and desirable properties, and presented
these measures graphically. An important property, that is,
monotonicity of the proposed measures has also been studied.
Abstract: In this study, we investigated the effects of ginger and
L-carnitine on the reproductive performance of male rats with respect
to semen parameters, male sex hormones and the testicular
antioxidant system. A total of sixty mature male albino rats were
divided into four groups of fifteen rats. The control group received
saline, whereas the other three groups received ginger (100 mg kg-1 d-
1.), L-carnitine (150 mg kg-1 d-1.) or a combination of both ginger
(100 mg kg-1 d-1.) and L-carnitine (150 mg kg-1 d-1.) via a stomach
tube daily for one month. At the end of the treatment period, the rats
were sacrificed, and their sperm characteristics (count, motility and
viability), antioxidant enzyme factors levels (reduced glutathione,
catalase, superoxide dismutase and total antioxidant capacity) and sex
hormone levels (testosterone, Follicle stimulating hormone(FSH) and
luteinizing hormone (LH) were analysed. Our results showed that the
three experimental treatments improved sperm parameters,
antioxidant enzyme activity and testosterone hormone levels; the
most pronounced positive effects were observed in the group that
received a combination of both ginger and L-carnitine. Therefore, the
administration of a combination of ginger and L-carnitine may be
beneficial for improving male sexual performance.
Abstract: ECG analysis method was developed using ROC
analysis of PVC detecting algorithm. ECG signal of MIT-BIH
arrhythmia database was analyzed by MATLAB. First of all, the
baseline was removed by median filter to preprocess the ECG signal.
R peaks were detected for ECG analysis method, and normal VCG
was extracted for VCG analysis method. Four PVC detecting
algorithm was analyzed by ROC curve, which parameters are
maximum amplitude of QRS complex, width of QRS complex, r-r
interval and geometric mean of VCG. To set cut-off value of
parameters, ROC curve was estimated by true-positive rate
(sensitivity) and false-positive rate. sensitivity and false negative rate
(specificity) of ROC curve calculated, and ECG was analyzed using
cut-off value which was estimated from ROC curve. As a result, PVC
detecting algorithm of VCG geometric mean have high availability,
and PVC could be detected more accurately with amplitude and width
of QRS complex.
Abstract: This research is aimed to compare the percentages of correct classification of Empirical Bayes method (EB) to Classical method when data are constructed as near normal, short-tailed and long-tailed symmetric, short-tailed and long-tailed asymmetric. The study is performed using conjugate prior, normal distribution with known mean and unknown variance. The estimated hyper-parameters obtained from EB method are replaced in the posterior predictive probability and used to predict new observations. Data are generated, consisting of training set and test set with the sample sizes 100, 200 and 500 for the binary classification. The results showed that EB method exhibited an improved performance over Classical method in all situations under study.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: The present study explains the effect of aggregate
gradation on moisture damage in bituminous mixes. Three types of
aggregate gradation and two types of binder; VG-30 and Polymer
modified bitumen (PMB-40) are used. Moisture susceptibility tests
like retained stability and tensile strength ratio (TSR) and static creep
test are conducted on Marshall specimens. The creep test was also
conducted for conditioned and unconditioned specimens to observe
the effect of moisture on creep behaviour. The results indicate that
Marshall stability value is higher in PMB-40 mix than VG-30 mixes.
Moisture susceptibility of PMB-40 mixes is low when compared with
mix using VG-30. The reduction in retained stability, and indirect
tensile strength and increase in creep are evaluated for finer, coarser
and normal gradation of aggregate to observe the effect of gradation
on moisture susceptibility of mixes. The retained stability is least
affected when compared with other moisture susceptibility
parameters
Abstract: Adsorption of Toluidine blue dye from aqueous solutions onto Neem Leaf Powder (NLP) has been investigated. The surface characterization of this natural material was examined by Particle size analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) spectroscopy and X-Ray Diffraction (XRD). The effects of process parameters such as initial concentration, pH, temperature and contact duration on the adsorption capacities have been evaluated, in which pH has been found to be most effective parameter among all. The data were analyzed using the Langmuir and Freundlich for explaining the equilibrium characteristics of adsorption. And kinetic models like pseudo first- order, second-order model and Elovich equation were utilized to describe the kinetic data. The experimental data were well fitted with Langmuir adsorption isotherm model and pseudo second order kinetic model. The thermodynamic parameters, such as Free energy of adsorption (AG"), enthalpy change (AH') and entropy change (AS°) were also determined and evaluated.
Abstract: In this work, we derive two numerical schemes for
solving a class of nonlinear partial differential equations. The first
method is of second order accuracy in space and time directions, the
scheme is unconditionally stable using Von Neumann stability
analysis, the scheme produced a nonlinear block system where
Newton-s method is used to solve it. The second method is of fourth
order accuracy in space and second order in time. The method is
unconditionally stable and Newton's method is used to solve the
nonlinear block system obtained. The exact single soliton solution
and the conserved quantities are used to assess the accuracy and to
show the robustness of the schemes. The interaction of two solitary
waves for different parameters are also discussed.
Abstract: In this study, a reformer model simulation to use
refinery (Farashband refinery, Iran) waste natural gas. In the
petroleum and allied sectors where natural gas is being encountered
(in form of associated gas) without prior preparation for its positive
use, its combustion (which takes place in flares, an equipment through
which they are being disposed) has become a great problem because
of its associated environmental problems in form of gaseous emission.
The proposed model is used to product syngas from waste natural gas.
A detailed steady model described by a set of ordinary differential and
algebraic equations was developed to predict the behavior of the
overall process. The proposed steady reactor model was validated
against process data of a reformer synthesis plant recorded and a good
agreement was achieved. H2/CO ratio has important effect on Fischer-
Tropsch synthesis reactor product and we try to achieve this parameter
with best designing reformer reactor. We study different kind of
reformer reactors and then select auto thermal reforming process of
natural gas in a fixed bed reformer that adjustment H2/CO ratio with
CO2 and H2O injection. Finally a strategy was proposed for prevention
of extra natural gas to atmosphere.
Abstract: In this paper, we address the problem of adaptive radio
resource allocation (RRA) and packet scheduling in the downlink of a
cellular OFDMA system, and propose a downlink multi-carrier
proportional fair (MPF) scheduler and its joint with adaptive RRA
algorithm to distribute radio resources among multiple users according
to their individual QoS requirements. The allocation and scheduling
objective is to maximize the total throughput, while at the same time
maintaining the fairness among users. The simulation results
demonstrate that the methods presented provide for user more explicit
fairness relative to RRA algorithm, but the joint scheme achieves the
higher sum-rate capacity with flexible parameters setting compared
with MPF scheduler.
Abstract: A numerical study on the influence of electroosmotic flow on analyte preconcentration by isotachophoresis ( ITP) is made. We consider that the double layer induced electroosmotic flow ( EOF) counterbalance the electrophoretic velocity and a stationary ITP stacked zones results. We solve the Navier-Stokes equations coupled with the Nernst-Planck equations to determine the local convective velocity and the preconcentration dynamics of ions. Our numerical algorithm is based on a finite volume method along with a secondorder upwind scheme. The present numerical algorithm can capture the the sharp boundaries of step-changes ( plateau mode) or zones of steep gradients ( peak mode) accurately. The convection of ions due to EOF reduces the resolution of the ITP transition zones and produces a dispersion in analyte zones. The role of the electrokinetic parameters which induces dispersion is analyzed. A one-dimensional model for the area-averaged concentrations based on the Taylor-Aristype effective diffusivity is found to be in good agreement with the computed solutions.
Abstract: The paper presents a complete discrete statistical framework, based on a novel vector quantization (VQ) front-end process. This new VQ approach performs an optimal distribution of VQ codebook components on HMM states. This technique that we named the distributed vector quantization (DVQ) of hidden Markov models, succeeds in unifying acoustic micro-structure and phonetic macro-structure, when the estimation of HMM parameters is performed. The DVQ technique is implemented through two variants. The first variant uses the K-means algorithm (K-means- DVQ) to optimize the VQ, while the second variant exploits the benefits of the classification behavior of neural networks (NN-DVQ) for the same purpose. The proposed variants are compared with the HMM-based baseline system by experiments of specific Arabic consonants recognition. The results show that the distributed vector quantization technique increase the performance of the discrete HMM system.
Abstract: Software Reliability is one of the key factors in the software development process. Software Reliability is estimated using reliability models based on Non Homogenous Poisson Process. In most of the literature the Software Reliability is predicted only in testing phase. So it leads to wrong decision-making concept. In this paper, two Software Reliability concepts, testing and operational phase are studied in detail. Using S-Shaped Software Reliability Growth Model (SRGM) and Exponential SRGM, the testing and operational reliability values are obtained. Finally two reliability values are compared and optimal release time is investigated.
Abstract: The effects of different parameters on the
hydrodynamics of trickle bed reactors were discussed for Newtonian
and non-Newtonian foaming systems. The varying parameters are
varying liquid velocities, gas flow velocities and surface tension. The
range for gas velocity is particularly large, thanks to the use of dense
gas to simulate very high pressure conditions. This data bank has
been used to compare the prediction accuracy of the different
trendlines and transition points from the literature. More than 240
experimental points for the trickle flow (GCF) and foaming pulsing
flow (PF/FPF) regime were obtained for present study.
Hydrodynamic characteristics involving dynamic liquid saturation
significantly influenced by gas and liquid flow rates. For 15 and 30
ppm air-aqueous surfactant solutions, dynamic liquid saturation
decreases with higher liquid and gas flow rates considerably in high
interaction regime. With decrease in surface tension i.e. for 45 and 60
ppm air-aqueous surfactant systems, effect was more pronounced
with decreases dynamic liquid saturation very sharply during regime
transition significantly at both low liquid and gas flow rates.