Abstract: Protecting is the sources of drinking water is the first
barrier of contamination of drinking water. The Feitsui Reservoir
watershed of Taiwan supplies domestic water for around 5 million
people in the Taipei metropolitan area. Understanding the spatial
patterns of water quality trends in this watershed is an important
agenda for management authorities. This study examined 7 sites in the
watershed for water quality parameters regulated in the standard for
drinking water source. The non-parametric seasonal Mann-Kendall-s
test was used to determine significant trends for each parameter.
Significant trends of increasing pH occurred at the sampling station in
the uppermost stream watershed, and in total phosphorus at 4 sampling
stations in the middle and downstream watershed. Additionally, the
multi-scale land cover assessment and average land slope were used to
explore the influence on the water quality in the watershed. Regression
models for predicting water quality were also developed.
Abstract: In this study, numerical simulations on laminar flow in
sinusoidal wavy shaped tubes were conducted for mean Reynolds
number of 250, which is in the range of physiological flow-rate and
investigated flow structures, pressure distribution and particle
trajectories both in steady and periodic inflow conditions. For
extensive comparisons, various wave lengths and amplitudes of sine
function for geometry of tube models were employed. The results
showed that small amplitude secondary curvature has significant
influence on the nature of flow patterns and particle mixing
mechanism. This implies that characterizing accurate geometry is
essential in accurate predicting of in vivo hemodynamics and may
motivate further study on any possibility of reflection of secondary
flow on vascular remodeling and pathophysiology.
Abstract: In this work, simulation algorithms for contact drying
of agitated particulate materials under vacuum and at atmospheric
pressure were developed. The implementation of algorithms gives a
predictive estimation of drying rate curves and bulk bed temperature
during contact drying. The calculations are based on the penetration
model to describe the drying process, where all process parameters
such as heat and mass transfer coefficients, effective bed properties,
gas and liquid phase properties are estimated with proper
correlations. Simulation results were compared with experimental
data from the literature. In both cases, simulation results were in good
agreement with experimental data. Few deviations were identified
and the limitations of the predictive capabilities of the models are
discussed. The programs give a good insight of the drying behaviour
of the analysed powders.
Abstract: This paper focuses on the development of bond graph
dynamic model of the mechanical dynamics of an excavating mechanism
previously designed to be used with small tractors, which are
fabricated in the Engineering Workshops of Jomo Kenyatta University
of Agriculture and Technology. To develop a mechanical dynamics
model of the manipulator, forward recursive equations similar to
those applied in iterative Newton-Euler method were used to obtain
kinematic relationships between the time rates of joint variables
and the generalized cartesian velocities for the centroids of the
links. Representing the obtained kinematic relationships in bondgraphic
form, while considering the link weights and momenta as
the elements led to a detailed bond graph model of the manipulator.
The bond graph method was found to reduce significantly the number
of recursive computations performed on a 3 DOF manipulator for a
mechanical dynamic model to result, hence indicating that bond graph
method is more computationally efficient than the Newton-Euler
method in developing dynamic models of 3 DOF planar manipulators.
The model was verified by comparing the joint torque expressions
of a two link planar manipulator to those obtained using Newton-
Euler and Lagrangian methods as analyzed in robotic textbooks. The
expressions were found to agree indicating that the model captures
the aspects of rigid body dynamics of the manipulator. Based on
the model developed, actuator sizing and valve sizing methodologies
were developed and used to obtain the optimal sizes of the pistons
and spool valve ports respectively. It was found that using the pump
with the sized flow rate capacity, the engine of the tractor is able to
power the excavating mechanism in digging a sandy-loom soil.
Abstract: 98% of the energy needed in Taiwan has been
imported. The prices of petroleum and electricity have been
increasing. In addition, facility capacity, amount of electricity
generation, amount of electricity consumption and number of Taiwan
Power Company customers have continued to increase. For these
reasons energy conservation has become an important topic. In the
past linear regression was used to establish the power consumption
models for chillers. In this study, grey prediction is used to evaluate
the power consumption of a chiller so as to lower the total power
consumption at peak-load (so that the relevant power providers do not
need to keep on increasing their power generation capacity and facility
capacity).
In grey prediction, only several numerical values (at least four
numerical values) are needed to establish the power consumption
models for chillers. If PLR, the temperatures of supply chilled-water
and return chilled-water, and the temperatures of supply cooling-water
and return cooling-water are taken into consideration, quite accurate
results (with the accuracy close to 99% for short-term predictions)
may be obtained. Through such methods, we can predict whether the
power consumption at peak-load will exceed the contract power
capacity signed by the corresponding entity and Taiwan Power
Company. If the power consumption at peak-load exceeds the power
demand, the temperature of the supply chilled-water may be adjusted
so as to reduce the PLR and hence lower the power consumption.
Abstract: In recent methodological articles related to structural equation modeling (SEM), the question of how to measure endogenous formative variables has been raised as an urgent, unresolved issue. This research presents an empirical application from the CRM system development context to test a recently developed technique, which makes it possible to measure endogenous formative constructs in structural models. PLS path modeling is used to demonstrate the feasibility of measuring antecedent relationships at the formative indicator level, not the formative construct level. Empirical results show that this technique is a promising approach to measure antecedent relationships of formative constructs in SEM.
Abstract: Software organizations are constantly looking for
better solutions when designing and using well-defined software
processes for the development of their products and services.
However, while the technical aspects are virtually easier to arrange,
many software development processes lack more support on project
management issues. When adopting such processes, an organization
needs to apply good project management skills along with technical
views provided by those models. This research proposes the
definition of a new model that integrates the concepts of PMBOK
and those available on the OPEN metamodel, helping not only
process integration but also building the steps towards a more
comprehensive and automatable model.
Abstract: The two-dimensional gel electrophoresis method
(2-DE) is widely used in Proteomics to separate thousands of proteins
in a sample. By comparing the protein expression levels of proteins in
a normal sample with those in a diseased one, it is possible to identify
a meaningful set of marker proteins for the targeted disease. The major
shortcomings of this approach involve inherent noises and irregular
geometric distortions of spots observed in 2-DE images. Various
experimental conditions can be the major causes of these problems. In
the protein analysis of samples, these problems eventually lead to
incorrect conclusions. In order to minimize the influence of these
problems, this paper proposes a partition based pair extension method
that performs spot-matching on a set of gel images multiple times and
segregates more reliable mapping results which can improve the
accuracy of gel image analysis. The improved accuracy of the
proposed method is analyzed through various experiments on real
2-DE images of human liver tissues.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: This paper presents the effect of driving a motor
vehicle on the stress levels of older drivers, indicated by monitoring
their hear rate increase whilst completing various everyday driving
tasks. Results suggest that whilst older female drivers heart rate varied
more significantly than males, the actual age of a participant did not
result in a significant change in heart rate due to stress, within the age
group tested. The analysis of the results indicates the most stressful
manoeuvres undertaken by the older drivers and highlights the tasks
which were found difficult with a view to implementing technologies
to aid the more senior driver in automotive travel.
Abstract: In this paper, penalized power-divergence test statistics have been defined and their exact size properties to test a nested sequence of log-linear models have been compared with ordinary power-divergence test statistics for various penalization, λ and main effect values. Since the ordinary and penalized power-divergence test statistics have the same asymptotic distribution, comparisons have been only made for small and moderate samples. Three-way contingency tables distributed according to a multinomial distribution have been considered. Simulation results reveal that penalized power-divergence test statistics perform much better than their ordinary counterparts.
Abstract: The coastal sediments of West Port of Malaysia was monitored from Nov. 2009 to Oct. 2010 to assess spatial distribution of heavy metals As, Cu, Cd, Cr, Hg, Ni, Zn and Pb. Sediment samples were collected from 10 stations in dry and rainy season in West Port. The range concentrations measured (Mg/g dry weight ) were from 23.4 to 98.3 for Zn, 22.3 to 80 for Pb, 7.4 to 27.6 Cu, 0.244 to 3.53 for Cd, 7.2 to 22.2 for Ni, 20.2 to 162 for As, 0.11 to 0.409 for Hg and 11.5 to 61.5 for Cr. The geochemical indexes used in this study were Geoaccumulation (Igeo), Contamination Factor (CF) and Pollution Load Index (PLI); these indexes were used to evaluate the levels of sediment contaminations. The results of these indexes show that, the status of West Port sediment quality are moderately polluted by heavy metals except in arsenic which shows the high level of pollution.
Abstract: Simultaneous effects of temperature, immersion time, salt concentration, sucrose concentration, pressure and convective dryer temperature on the combined osmotic dehydration - convective drying of edible button mushrooms were investigated. Experiments were designed according to Central Composite Design with six factors each at five different levels. Response Surface Methodology (RSM) was used to determine the optimum processing conditions that yield maximum water loss and rehydration ratio and minimum solid gain and shrinkage in osmotic-convective drying of edible button mushrooms. Applying surfaces profiler and contour plots optimum operation conditions were found to be temperature of 39 °C, immersion time of 164 min, salt concentration of 14%, sucrose concentration of 53%, pressure of 600 mbar and drying temperature of 40 °C. At these optimum conditions, water loss, solid gain, rehydration ratio and shrinkage were found to be 63.38 (g/100 g initial sample), 3.17 (g/100 g initial sample), 2.26 and 7.15%, respectively.
Abstract: Using Dynamic Bayesian Networks (DBN) to model genetic regulatory networks from gene expression data is one of the major paradigms for inferring the interactions among genes. Averaging a collection of models for predicting network is desired, rather than relying on a single high scoring model. In this paper, two kinds of model searching approaches are compared, which are Greedy hill-climbing Search with Restarts (GSR) and Markov Chain Monte Carlo (MCMC) methods. The GSR is preferred in many papers, but there is no such comparison study about which one is better for DBN models. Different types of experiments have been carried out to try to give a benchmark test to these approaches. Our experimental results demonstrated that on average the MCMC methods outperform the GSR in accuracy of predicted network, and having the comparable performance in time efficiency. By proposing the different variations of MCMC and employing simulated annealing strategy, the MCMC methods become more efficient and stable. Apart from comparisons between these approaches, another objective of this study is to investigate the feasibility of using DBN modeling approaches for inferring gene networks from few snapshots of high dimensional gene profiles. Through synthetic data experiments as well as systematic data experiments, the experimental results revealed how the performances of these approaches can be influenced as the target gene network varies in the network size, data size, as well as system complexity.
Abstract: In rail vehicles, air springs are very important isolating component, which guarantee good ride comfort for passengers during their trip. In the most new rail–vehicle models, developed by researchers, the thermo–dynamical effects of air springs are ignored and secondary suspension is modeled by simple springs and dampers. As the performance of suspension components have significant effects on rail–vehicle dynamics and ride comfort of passengers, a complete nonlinear thermo–dynamical air spring model, which is a combination of two different models, is introduced. Result from field test shows remarkable agreement between proposed model and experimental data. Effects of air suspension parameters on the system performances are investigated here and then these parameters are tuned to minimize Sperling ride comfort index during the trip. Results showed that by modification of air suspension parameters, passengers comfort is improved and ride comfort index is reduced about 10%.
Abstract: The present microfluidic study is emphasizing the flow behavior within a Y shape micro-bifurcation in two similar flow configurations. We report here a numerical and experimental investigation on the velocity profiles evolution and secondary flows, manifested at different Reynolds numbers (Re) and for two different boundary conditions. The experiments are performed using special designed setup based on optical microscopic devices. With this setup, direct visualizations and quantitative measurements of the path-lines are obtained. A Micro-PIV measurement system is used to obtain velocity profiles distributions in a spatial evolution in the main flows domains. The experimental data is compared with numerical simulations performed with commercial computational code FLUENT in a 3D geometry with the same dimensions as the experimental one. The numerical flow patterns are found to be in good agreement with the experimental manifestations.
Abstract: The human head representations usually are based on
the morphological – structural components of a real model. Over the
time became more and more necessary to achieve full virtual models
that comply very rigorous with the specifications of the human
anatomy. Still, making and using a model perfectly fitted with the
real anatomy is a difficult task, because it requires large hardware
resources and significant times for processing. That is why it is
necessary to choose the best compromise solution, which keeps the
right balance between the details perfection and the resources
consumption, in order to obtain facial animations with real-time
rendering. We will present here the way in which we achieved such a
3D system that we intend to use as a base point in order to create
facial animations with real-time rendering, used in medicine to find
and to identify different types of pathologies.
Abstract: This paper addresses the development of an intelligent vision system for human-robot interaction. The two novel contributions of this paper are 1) Detection of human faces and 2) Localizing the eye. The method is based on visual attributes of human skin colors and geometrical analysis of face skeleton. This paper introduces a spatial domain filtering method named ?Fuzzily skewed filter' which incorporates Fuzzy rules for deciding the gray level of pixels in the image in their neighborhoods and takes advantages of both the median and averaging filters. The effectiveness of the method has been justified over implementing the eye tracking commands to an entertainment robot, named ''AIBO''.
Abstract: Covering-based rough sets is an extension of rough
sets and it is based on a covering instead of a partition of the
universe. Therefore it is more powerful in describing some practical
problems than rough sets. However, by extending the rough sets,
covering-based rough sets can increase the roughness of each model
in recognizing objects. How to obtain better approximations from
the models of a covering-based rough sets is an important issue.
In this paper, two concepts, determinate elements and indeterminate
elements in a universe, are proposed and given precise definitions
respectively. This research makes a reasonable refinement of the
covering-element from a new viewpoint. And the refinement may
generate better approximations of covering-based rough sets models.
To prove the theory above, it is applied to eight major coveringbased
rough sets models which are adapted from other literature.
The result is, in all these models, the lower approximation increases
effectively. Correspondingly, in all models, the upper approximation
decreases with exceptions of two models in some special situations.
Therefore, the roughness of recognizing objects is reduced. This
research provides a new approach to the study and application of
covering-based rough sets.
Abstract: The purpose of this paper is to study Database Models
to use them efficiently in E-commerce websites. In this paper we are
going to find a method which can save and retrieve information in Ecommerce
websites. Thus, semantic web applications can work with,
and we are also going to study different technologies of E-commerce
databases and we know that one of the most important deficits in
semantic web is the shortage of semantic data, since most of the
information is still stored in relational databases, we present an
approach to map legacy data stored in relational databases into the
Semantic Web using virtually any modern RDF query language, as
long as it is closed within RDF. To achieve this goal we study XML
structures for relational data bases of old websites and eventually we
will come up one level over XML and look for a map from relational
model (RDM) to RDF. Noting that a large number of semantic webs
get advantage of relational model, opening the ways which can be
converted to XML and RDF in modern systems (semantic web) is
important.