Abstract: Increasing user comfort and reducing operation costs
have always been primary objectives of lighting control strategies in a
building. This paper proposes an architecture of the lighting control
system for a daylit office. The system consists of the lighting
controller, A/D & D/A converter, dimmable LED lights, and the
lighting management software. Verification tests are conducted using
the proposed system specialized for the interior lighting of a open-plan
office. The results showed the proposed architecture of the lighting
system would improve the overall system reliability, lower the system
cost, and provide ease of installation and maintenance.
Abstract: In this paper, we consider a two-neuron system with time-delayed connections between neurons. By analyzing the associated characteristic transcendental equation, its linear stability is investigated and Hopf bifurcation is demonstrated. Some explicit formulae for determining the stability and the direction of the Hopf bifurcation periodic solutions bifurcating from Hopf bifurcations are obtained by using the normal form theory and center manifold theory. Some numerical simulation results are given to support the theoretical predictions. Finally, main conclusions are given.
Abstract: Based on the sources- smoothed rank profile (SRP) and modified minimum description length (MMDL) principle, a method for estimation of the source coherency structure (SCS) and the number of wideband sources is proposed in this paper. Instead of focusing, we first use a spatial smoothing technique to pre-process the array covariance matrix of each frequency for de-correlating the sources and then use smoothed rank profile to determine the SCS and the number of wideband sources. We demonstrate the availability of the method by numerical simulations.
Abstract: This paper deals with stability analysis for synchronous reluctance motors drive. Special attention is paid to the transient performance with variations in motor's parameters such as Ld and Rs. A study of the dynamic control using d-q model is presented first in order to clarify the stability of the motor drive system. Based on the experimental parameters of the synchronous reluctance motor, this paper gives some simulation results using MATLAB/SIMULINK software packages. It is concluded that the motor parameters, especially Ld, affect the estimator stability and hence the whole drive system.
Abstract: In this paper, we introduce an mobile agent framework
with proactive load balancing for ambient intelligence (AmI) environments.
One of the main obstacles of AmI is the scalability in
which the openness of AmI environment introduces dynamic resource
requirements on agencies. To mediate this scalability problem, our
framework proposes a load balancing module to proactively analyze
the resource consumption of network bandwidth and preferred agencies
to suggest the optimal communication method to its user. The
framework generally formulates an AmI environment that consists
of three main components: (1) mobile devices, (2) hosts or agencies,
and (3) directory service center (DSC). A preliminary implementation
was conducted with NetLogo and the experimental results show that
the proposed approach provides enhanced system performance by
minimizing the network utilization to provide users with responsive
services.
Abstract: This paper presents a cold flow simulation study of a small gas turbine combustor performed using laboratory scale test rig. The main objective of this investigation is to obtain physical insight of the main vortex, responsible for the efficient mixing of fuel and air. Such models are necessary for predictions and optimization of real gas turbine combustors. Air swirler can control the combustor performance by assisting in the fuel-air mixing process and by producing recirculation region which can act as flame holders and influences residence time. Thus, proper selection of a swirler is needed to enhance combustor performance and to reduce NOx emissions. Three different axial air swirlers were used based on their vane angles i.e., 30°, 45°, and 60°. Three-dimensional, viscous, turbulent, isothermal flow characteristics of the combustor model operating at room temperature were simulated via Reynolds- Averaged Navier-Stokes (RANS) code. The model geometry has been created using solid model, and the meshing has been done using GAMBIT preprocessing package. Finally, the solution and analysis were carried out in a FLUENT solver. This serves to demonstrate the capability of the code for design and analysis of real combustor. The effects of swirlers and mass flow rate were examined. Details of the complex flow structure such as vortices and recirculation zones were obtained by the simulation model. The computational model predicts a major recirculation zone in the central region immediately downstream of the fuel nozzle and a second recirculation zone in the upstream corner of the combustion chamber. It is also shown that swirler angles changes have significant effects on the combustor flowfield as well as pressure losses.
Abstract: The occurrence and removal of trace organic
contaminants in the aquatic environment has become a focus of
environmental concern. For the selective removal of carbamazepine
from loaded waters molecularly imprinted polymers (MIPs) were
synthesized with carbamazepine as template. Parameters varied were
the type of monomer, crosslinker, and porogen, the ratio of starting
materials, and the synthesis temperature. Best results were obtained
with a template to crosslinker ratio of 1:20, toluene as porogen, and
methacrylic acid (MAA) as monomer. MIPs were then capable to
recover carbamazepine by 93% from a 10-5 M landfill leachate
solution containing also caffeine and salicylic acid. By comparison,
carbamazepine recoveries of 75% were achieved using a nonimprinted
polymer (NIP) synthesized under the same conditions, but
without template. In landfill leachate containing solutions
carbamazepine was adsorbed by 93-96% compared with an uptake of
73% by activated carbon. The best solvent for desorption was
acetonitrile, with which the amount of solvent necessary and dilution
with water was tested. Selected MIPs were tested for their reusability
and showed good results for at least five cycles. Adsorption
isotherms were prepared with carbamazepine solutions in the
concentration range of 0.01 M to 5*10-6 M. The heterogeneity index
showed a more homogenous binding site distribution.
Abstract: In this treatise we will study the capability of static
compensator for reactive power to stabilize sheen voltage with motor
loading on power networks system. We also explain the structure and main function of STATCOM and the method to control it using STATCOM transformer current to simultaneously predict after
telling about the necessity of FACTS tools to compensate in power networks. Then we study topology and controlling system to stabilize
voltage during start of inductive motor. The outcome of stimulat by MATLAB software supports presented controlling idea and
system in the treatise.
Abstract: This paper considers the robust exponential stability issues for a class of uncertain switched neutral system which delays switched according to the switching rule. The system under consideration includes both stable and unstable subsystems. The uncertainties considered in this paper are norm bounded, and possibly time varying. Based on multiple Lyapunov functional approach and dwell-time technique, the time-dependent switching rule is designed depend on the so-called average dwell time of stable subsystems as well as the ratio of the total activation time of stable subsystems and unstable subsystems. It is shown that by suitably controlling the switching between the stable and unstable modes, the robust stabilization of the switched uncertain neutral systems can be achieved. Two simulation examples are given to demonstrate the effectiveness of the proposed method.
Abstract: one of the significant factors for improving the
accuracy of Land Surface Temperature (LST) retrieval is the correct
understanding of the directional anisotropy for thermal radiance. In
this paper, the multiple scattering effect between heterogeneous
non-isothermal surfaces is described rigorously according to the
concept of configuration factor, based on which a directional thermal
radiance model is built, and the directional radiant character for urban
canopy is analyzed. The model is applied to a simple urban canopy
with row structure to simulate the change of Directional Brightness
Temperature (DBT). The results show that the DBT is aggrandized
because of the multiple scattering effects, whereas the change range of
DBT is smoothed. The temperature difference, spatial distribution,
emissivity of the components can all lead to the change of DBT. The
“hot spot" phenomenon occurs when the proportion of high
temperature component in the vision field came to a head. On the other
hand, the “cool spot" phenomena occur when low temperature
proportion came to the head. The “spot" effect disappears only when
the proportion of every component keeps invariability. The model
built in this paper can be used for the study of directional effect on
emissivity, the LST retrieval over urban areas and the adjacency effect
of thermal remote sensing pixels.
Abstract: In recent years, new product development became more and more competitive and globalized, and the designing phase is critical for the product success. The concept of modularity can provide the necessary foundation for organizations to design products that can respond rapidly to market needs. The paper describes data structures and algorithms of intelligent Web-based system for modular design taking into account modules compatibility relationship and given design requirements. The system intelligence is realized by developed algorithms for choice of modules reflecting all system restrictions and requirements. The proposed data structure and algorithms are illustrated by case study of personal computer configuration. The applicability of the proposed approach is tested through a prototype of Web-based system.
Abstract: The design of a landing gear is one of the fundamental aspects of aircraft design. The need for a light weight, high strength, and stiffness characteristics coupled with techno economic feasibility are a key to the acceptability of any landing gear construction. In this paper, an approach for analyzing two different designed landing gears for an unmanned aircraft vehicle (UAV) using advanced CAE techniques will be applied. Different landing conditions have been considered for both models. The maximum principle stresses for each model along with the factor of safety are calculated for every loading condition. A conclusion is drawing about better geometry.
Abstract: The ability of agricultural and decorative plants to
absorb and detoxify TNT and RDX has been studied. All tested 8
plants, grown hydroponically, were able to absorb these explosives
from water solutions: Alfalfa > Soybean > Chickpea> Chikling vetch
>Ryegrass > Mung bean> China bean > Maize. Differently from
TNT, RDX did not exhibit negative influence on seed germination
and plant growth. Moreover, some plants, exposed to RDX
containing solution were increased in their biomass by 20%. Study of
the fate of absorbed [1-14ðí]-TNT revealed the label distribution in
low and high-molecular mass compounds, both in roots and above
ground parts of plants, prevailing in the later. Content of 14ðí in lowmolecular
compounds in plant roots are much higher than in above
ground parts. On the contrary, high-molecular compounds are more
intensively labeled in aboveground parts of soybean. Most part (up to
70%) of metabolites of TNT, formed either by enzymatic reduction
or oxidation, is found in high molecular insoluble conjugates.
Activation of enzymes, responsible for reduction, oxidation and
conjugation of TNT, such as nitroreductase, peroxidase,
phenoloxidase and glutathione S-transferase has been demonstrated.
Among these enzymes, only nitroreductase was shown to be induced
in alfalfa, exposed to RDX. The increase in malate dehydrogenase
activities in plants, exposed to both explosives, indicates
intensification of Tricarboxylic Acid Cycle, that generates reduced
equivalents of NAD(P)H, necessary for functioning of the
nitroreductase. The hypothetic scheme of TNT metabolism in plants
is proposed.
Abstract: Structured catalysts formed from the growth of
zeolites on substrates is an area of increasing interest due to the
increased efficiency of the catalytic process, and the ability to
provide superior heat transfer and thermal conductivity for both
exothermic and endothermic processes.
However, the generation of structured catalysts represents a
significant challenge when balancing the relationship variables
between materials properties and catalytic performance, with the
Na2O, H2O and Al2O3 gel composition paying a significant role in
this dynamic, thereby affecting the both the type and range of
application.
The structured catalyst films generated as part of this
investigation have been characterised using a range of techniques,
including X-ray diffraction (XRD), Electron microscopy (SEM),
Energy Dispersive X-ray analysis (EDX) and Thermogravimetric
Analysis (TGA), with the transition from oxide-on-alloy wires to
hydrothermally synthesised uniformly zeolite coated surfaces being
demonstrated using both SEM and XRD. The robustness of the
coatings has been ascertained by subjecting these to thermal cycling
(ambient to 550oC), with the results indicating that the synthesis time
and gel compositions have a crucial effect on the quality of zeolite
growth on the FeCrAlloy wires.
Finally, the activity of the structured catalyst was verified by a
series of comparison experiments with standard zeolite Y catalysts in
powdered pelleted forms.
Abstract: An overview of the important aspects of managing
and controlling industrial effluent discharges to public sewers namely
sampling, characterization, quantification and legislative controls has
been presented. The findings have been validated by means of a case
study covering three industrial sectors namely, tanning, textile
finishing and food processing industries. Industrial effluents
discharges were found to be best monitored by systematic and
automatic sampling and quantified using water meter readings
corrected for evaporative and consumptive losses. Based on the
treatment processes employed in the public owned treatment works
and the chemical oxygen demand and biochemical oxygen demand
levels obtained, the effluent from all the three industrial sectors
studied were found to lie in the toxic zone. Thus, physico-chemical
treatment of these effluents is required to bring them into the
biodegradable zone. KL values (quoted to base e) were greater than
0.50 day-1 compared to 0.39 day-1 for typical municipality
wastewater.
Abstract: In the highly competitive and rapidly changing global
marketplace, independent organizations and enterprises often come
together and form a temporary alignment of virtual enterprise in a
supply chain to better provide products or service. As firms adopt the
systems approach implicit in supply chain management, they must
manage the quality from both internal process control and external
control of supplier quality and customer requirements. How to
incorporate quality management of upstream and downstream supply
chain partners into their own quality management system has recently
received a great deal of attention from both academic and practice.
This paper investigate the collaborative feature and the entities-
relationship in a supply chain, and presents an ontology of
collaborative supply chain from an approach of aligning
service-oriented framework with service-dominant logic. This
perspective facilitates the segregation of material flow management
from manufacturing capability management, which provides a
foundation for the coordination and integration of the business process
to measure, analyze, and continually improve the quality of products,
services, and process. Further, this approach characterizes the different
interests of supply chain partners, providing an innovative approach to
analyze the collaborative features of supply chain. Furthermore, this
ontology is the foundation to develop quality management system
which internalizes the quality management in upstream and
downstream supply chain partners and manages the quality in supply
chain systematically.
Abstract: Over the years, there is a growing trend towards
quality-based specifications in highway construction. In many
Quality Control/Quality Assurance (QC/QA) specifications, the
contractor is primarily responsible for quality control of the process,
whereas the highway agency is responsible for testing the acceptance
of the product. A cooperative investigation was conducted in Illinois
over several years to develop a prototype End-Result Specification
(ERS) for asphalt pavement construction. The final characteristics of
the product are stipulated in the ERS and the contractor is given
considerable freedom in achieving those characteristics. The risk for
the contractor or agency depends on how the acceptance limits and
processes are specified. Stochastic simulation models are very useful
in estimating and analyzing payment risk in ERS systems and these
form an integral part of the Illinois-s prototype ERS system. This
paper describes the development of an innovative methodology to
estimate the variability components in in-situ density, air voids and
asphalt content data from ERS projects. The information gained from
this would be crucial in simulating these ERS projects for estimation
and analysis of payment risks associated with asphalt pavement
construction. However, these methods require at least two parties to
conduct tests on all the split samples obtained according to the
sampling scheme prescribed in present ERS implemented in Illinois.
Abstract: A robust control approach is proposed for a high speed manipulator using a hybrid computed torque control approach in the state space. The high-speed manipulator is driven by permanent magnet dc motors to track a trajectory in the joint space in the presence of disturbances. Tracking problem is analyzed in the state space where the completed models are considered for actuators. The proposed control approach can guarantee the stability and a satisfactory tracking performance. A two-link elbow manipulator driven by electrical actuators is simulated and results are shown to satisfy conditions under technical specifications.
Abstract: In recent years, it has been proposed security
architecture for sensor network.[2][4]. One of these, TinySec by Chris
Kalof, Naveen Sastry, David Wagner had proposed Link layer security
architecture, considering some problems of sensor network. (i.e :
energy, bandwidth, computation capability,etc). The TinySec employs
CBC_mode of encryption and CBC-MAC for authentication based on
SkipJack Block Cipher. Currently, This TinySec is incorporated in the
TinyOS for sensor network security.
This paper introduces TinyHash based on general hash algorithm.
TinyHash is the module in order to replace parts of authentication and
integrity in the TinySec. it implies that apply hash algorithm on
TinySec architecture. For compatibility about TinySec, Components
in TinyHash is constructed as similar structure of TinySec. And
TinyHash implements the HMAC component for authentication and
the Digest component for integrity of messages. Additionally, we
define the some interfaces for service associated with hash algorithm.
Abstract: The development of the power electronics has allowed
increasing the precision and reliability of the electrical trainings,
thanks to the adjustable inverters, as the Pulse Wide Modulation
(PWM) five level inverters, which is the object of study in this
article.The authors treat the relation between the law order adopted for
a given system and the oscillations of the electrical and mechanical
parameters of which the tolerance depends on the process with which
they are integrated (paper factory, lifting of the heavy loads,
etc.).Thus the best choice of the regulation indexes allows us to
achieve stability and safety training without investment (management
of existing equipment).