Abstract: This paper presents a novel three-phase utility
frequency to high frequency soft switching power conversion circuit
with dual mode pulse width modulation and pulse density modulation
for high power induction heating applications as melting of steel and
non ferrous metals, annealing of metals, surface hardening of steel
and cast iron work pieces and hot water producers, steamers and
super heated steamers. This high frequency power conversion circuit
can operate from three-phase systems to produce high current for
high power induction heating applications under the principles of
ZVS and it can regulate its ac output power from the rated value to a
low power level. A dual mode modulation control scheme based on
high frequency PWM in synchronization with the utility frequency
positive and negative half cycles for the proposed high frequency
conversion circuit and utility frequency pulse density modulation is
produced to extend its soft switching operating range for wide ac
output power regulation. A dual packs heat exchanger assembly is
designed to be used in consumer and industrial fluid pipeline systems
and it is proved to be suitable for the hot water, steam and super
heated steam producers. Experiment and simulation results are given
in this paper to verify the operation principles of the proposed ac
conversion circuit and to evaluate its power regulation and
conversion efficiency. Also, the paper presents a mutual coupling
model of the induction heating load instead of equivalent transformer
circuit model.
Abstract: The objective of this paper is to present a
comparative study of Homotopy Perturbation Method (HPM),
Variational Iteration Method (VIM) and Homotopy Analysis
Method (HAM) for the semi analytical solution of Kortweg-de
Vries (KdV) type equation called KdV. The study have been
highlighted the efficiency and capability of aforementioned methods
in solving these nonlinear problems which has been arisen from a
number of important physical phenomenon.
Abstract: Most HWRs currently use natural uranium fuel. Using enriched uranium fuel results in a significant improvement in fuel cycle costs and uranium utilization. On the other hand, reactivity changes of HWRs over the full range of operating conditions from cold shutdown to full power are small. This reduces the required reactivity worth of control devices and minimizes local flux distribution perturbations, minimizing potential problems due to transient local overheating of fuel. Analyzing heavy water effectiveness on neutronic parameters such as enrichment requirements, peaking factor and reactivity is important and should pay attention as primary concepts of a HWR core designing. Two nuclear nuclear reactors of CANDU-type and hexagonal-type reactor cores of 33 fuel assemblies and 19 assemblies in 1.04 P/D have been respectively simulated using MCNP-4C code. Using heavy water and light water as moderator have been compared for achieving less reactivity insertion and enrichment requirements. Two fuel matrixes of (232Th/235U)O2 and (238/235U)O2 have been compared to achieve more economical and safe design. Heavy water not only decreased enrichment needs, but it concluded in negative reactivity insertions during moderator density variations. Thorium oxide fuel assemblies of 2.3% enrichment loaded into the core of heavy water moderator resulted in 0.751 fission to absorption ratio and peaking factor of 1.7 using. Heavy water not only provides negative reactivity insertion during temperature raises which changes moderator density but concluded in 2 to 10 kg reduction of enrichment requirements, depend on geometry type.
Abstract: The success of an electronic system in a System-on- Chip is highly dependent on the efficiency of its interconnection network, which is constructed from routers and channels (the routers move data across the channels between nodes). Since neither classical bus based nor point to point architectures can provide scalable solutions and satisfy the tight power and performance requirements of future applications, the Network-on-Chip (NoC) approach has recently been proposed as a promising solution. Indeed, in contrast to the traditional solutions, the NoC approach can provide large bandwidth with moderate area overhead. The selected topology of the components interconnects plays prime rule in the performance of NoC architecture as well as routing and switching techniques that can be used. In this paper, we present two generic NoC architectures that can be customized to the specific communication needs of an application in order to reduce the area with minimal degradation of the latency of the system. An experimental study is performed to compare these structures with basic NoC topologies represented by 2D mesh, Butterfly-Fat Tree (BFT) and SPIN. It is shown that Cluster mesh (CMesh) and MinRoot schemes achieves significant improvements in network latency and energy consumption with only negligible area overhead and complexity over existing architectures. In fact, in the case of basic NoC topologies, CMesh and MinRoot schemes provides substantial savings in area as well, because they requires fewer routers. The simulation results show that CMesh and MinRoot networks outperforms MESH, BFT and SPIN in main performance metrics.
Abstract: Innovations and innovative activity get the increasing
value for successful financial and economic activity of the countries
and regions. The level of innovative sphere development determines
place of a country or a region in world economy and forms a basis of
steady economic growth. This article is devoted to different aspects
of organization of the national economic safety in the conditions of
innovative development, its problems, risks and threats. Economy
can be considered as aspiring for transition to innovative way only
with finding of economic safety: financial independence, power
stability and technological progress. There are statistical indicators,
defining the level of economic security and factors, threatening
economic safety of the state. The research is based on the analysis of
factors and indicators in conditions of innovative development. The
paper is illustrated by the examples of possible estimated system of
the economic safety level.
Abstract: The decision of information technology (IT) outsourcing requires close attention to the evaluation of supplier selection process because the selection decision involves conflicting multiple criteria and is replete with complex decision making problems. Selecting the most appropriate suppliers is considered an important strategic decision that may impact the performance of outsourcing engagements. The objective of this paper is to aid decision makers to evaluate and assess possible IT outsourcing suppliers. An axiomatic design based fuzzy group decision making is adopted to evaluate supplier alternatives. Finally, a case study is given to demonstrate the potential of the methodology. KeywordsIT outsourcing, Supplier selection, Multi-criteria decision making, Axiomatic design, Fuzzy logic.
Abstract: This research proposes the state of art on how to control or find the trajectory paths of the RRP robot when the prismatic joint is malfunction. According to this situation, the minimum energy of the dynamic optimization is applied. The RRP robot or similar systems have been used in many areas such as fire fighter truck, laboratory equipment and military truck for example a rocket launcher. In order to keep on task that assigned, the trajectory paths must be computed. Here, the open loop control is applied and the result of an example show the reasonable solution which can be applied to the controllable system.
Abstract: Quantum cryptography offers a way of key agreement,
which is unbreakable by any external adversary. Authentication is
of crucial importance, as perfect secrecy is worthless if the identity
of the addressee cannot be ensured before sending important information.
Message authentication has been studied thoroughly, but no
approach seems to be able to explicitly counter meet-in-the-middle
impersonation attacks. The goal of this paper is the development of
an authentication scheme being resistant against active adversaries
controlling the communication channel. The scheme is built on top
of a key-establishment protocol and is unconditionally secure if built
upon quantum cryptographic key exchange. In general, the security
is the same as for the key-agreement protocol lying underneath.
Abstract: An adaptive fuzzy PID controller with gain scheduling is proposed in this paper. The structure of the proposed gain scheduled fuzzy PID (GS_FPID) controller consists of both fuzzy PI-like controller and fuzzy PD-like controller. Both of fuzzy PI-like and PD-like controllers are weighted through adaptive gain scheduling, which are also determined by fuzzy logic inference. A modified genetic algorithm called accumulated genetic algorithm is designed to learn the parameters of fuzzy inference system. In order to learn the number of fuzzy rules required for the TSK model, the fuzzy rules are learned in an accumulated way. In other words, the parameters learned in the previous rules are accumulated and updated along with the parameters in the current rule. It will be shown that the proposed GS_FPID controllers learned by the accumulated GA perform well for not only the regular linear systems but also the higher order and time-delayed systems.
Abstract: Viral influenza A subtypes H5N1 and pandemic
H1N1 (pH1N1) have worldwide emerged and transmitted. The most
common anti-influenza drug for treatment of both seasonal and
pandemic influenza viruses is oseltamivir that nowadays becomes
resistance to influenza neuraminidase. The novel long-acting drug,
laninamivir, was discovered for treatment of the patients infected
with influenza B and influenza A viruses. In the present study,
laninamivir complexed with wild-type strain of both H5N1 and
pH1N1 viruses were comparatively determined the structures and
drug-target interactions by means of molecular dynamics (MD)
simulations. The results show that the hydrogen bonding interactions
formed between laninamivir and its binding residues are likely
similar for the two systems. Additionally, the presence of
intermolecular interactions from laninamivir to the residues in the
binding pocket is established through their side chains in accordance
with hydrogen bond interactions.
Abstract: The paper describes ergonomics problems trend of
student at B5101 classroom building 2, Suranaree University of
Technology. The objective to survey ergonomics problems and effect
from use chairs for sitting in class room. The result from survey
method 100 student they use lecture chair for sitting in classroom
more than 2 hours/ day by RULA[1]. and Body discomfort survey[2].
The result from Body discomfort survey contribute fatigue problems
at neck, lower back, upper back and right shoulder 2.93, 2.91, 2.33,
1.75 respectively and result from RULA contribute fatigue problems
at neck, body and right upper arm 4.00, 3.75 and 3.00 respectively
are consistent. After that the researcher provide improvement plan
for design new chair support student fatigue reduction by prepare
data of sample anthropometry and design ergonomics chair prototype
3 unit. Then sample 100 student trial to use new chair and evaluate
again by RULA, Body discomfort and satisfaction. The result from
trial new chair after improvement by RULA present fatigue reduction
average of head and neck from 4.00 to 2.25 , body and trunk from
3.75 to 2.00 and arm force from 1.00 to 0.25 respectively. The result
from trial new chair after improvement by Body discomfort present
fatigue reduction average of lower back from 2.91 to 0.87, neck from
2.93 to 1.24, upper back 2.33 to 0.84 and right upper arm from 1.75
to 0.74. That statistical of RULA and Body discomfort survey
present fatigue reduction after improvement significance with a
confidence level of 95% (p-value 0.05). When analyzing the
relationship of fatigue as part of the body by Chi – square test during
RULA and Body discomfort that before and after improvements were
consistent with the significant level of confidence 95% (p-value 0.05)
. Moreover the students satisfaction result from trial with a new chair
for 30 minutes [3]. 72 percent very satisfied of the folding of the
secondary writing simple 66% the width of the writing plate, 64% the
suitability of the writing plate, 62% of soft seat cushion and 61%
easy to seat the chair.
Abstract: This purpose of this paper is to present the acceptance single sampling plan when the fraction of nonconforming items is a fuzzy number and being modeled based on the fuzzy Poisson distribution. We have shown that the operating characteristic (oc) curves of the plan is like a band having a high and low bounds whose width depends on the ambiguity proportion parameter in the lot when that sample size and acceptance numbers is fixed. Finally we completed discuss opinion by a numerical example. And then we compared the oc bands of using of binomial with the oc bands of using of Poisson distribution.
Abstract: This paper provides an introduction into the
evolution of information and communication technology and illustrates its usage in the work domain. The paper is sub-divided into two parts. The first part gives an overview over the different
phases of information processing in the work domain. It starts by
charting the past and present usage of computers in work
environments and shows current technological trends, which are likely to influence future business applications. The second part
starts by briefly describing, how the usage of computers changed business processes in the past, and presents first Ambient
Intelligence applications based on identification and localization
information, which are already used in the production and retail sector. Based on current systems and prototype applications, the
paper gives an outlook of how Ambient Intelligence technologies could change business processes in the future.
Abstract: High level synthesis (HLS) is a process which
generates register-transfer level design for digital systems from
behavioral description. There are many HLS algorithms and
commercial tools. However, most of these algorithms consider a
behavioral description for the system when a single token is
presented to the system. This approach does not exploit extra
hardware efficiently, especially in the design of digital filters where
common operations may exist between successive tokens. In this
paper, we modify the behavioral description to process multiple
tokens in parallel. However, this approach is unlike the full
processing that requires full hardware replication. It exploits the
presence of common operations between successive tokens. The
performance of the proposed approach is better than sequential
processing and approaches that of full parallel processing as the
hardware resources are increased.
Abstract: There was studied dynamic of the number of
nematodes fauna of various ecosystems of Gombori Mountain Ridge
that belongs to peak of fauna dynamic. The nature of dynamic is in
general similar in all six biotypes and the difference is evident only in
total number of nematodes.
Abstract: A new Feed-Forward/Feedback Generalized
Minimum Variance Pole-placement Controller to incorporate the
robustness of classical pole-placement into the flexibility of
generalized minimum variance self-tuning controller for Single-Input
Single-Output (SISO) has been proposed in this paper. The design,
which provides the user with an adaptive mechanism, which ensures
that the closed loop poles are, located at their pre-specified positions.
In addition, the controller design which has a feed-forward/feedback
structure overcomes the certain limitations existing in similar poleplacement
control designs whilst retaining the simplicity of
adaptation mechanisms used in other designs. It tracks set-point
changes with the desired speed of response, penalizes excessive
control action, and can be applied to non-minimum phase systems.
Besides, at steady state, the controller has the ability to regulate the
constant load disturbance to zero. Example simulation results using
both simulated and real plant models demonstrate the effectiveness of
the proposed controller.
Abstract: In this paper we are interested in classification problems
with a performance constraint on error probability. In such
problems if the constraint cannot be satisfied, then a rejection option
is introduced. For binary labelled classification, a number of SVM
based methods with rejection option have been proposed over the
past few years. All of these methods use two thresholds on the SVM
output. However, in previous works, we have shown on synthetic data
that using thresholds on the output of the optimal SVM may lead to
poor results for classification tasks with performance constraint. In
this paper a new method for supervised classification with rejection
option is proposed. It consists in two different classifiers jointly
optimized to minimize the rejection probability subject to a given
constraint on error rate. This method uses a new kernel based linear
learning machine that we have recently presented. This learning
machine is characterized by its simplicity and high training speed
which makes the simultaneous optimization of the two classifiers
computationally reasonable. The proposed classification method with
rejection option is compared to a SVM based rejection method
proposed in recent literature. Experiments show the superiority of
the proposed method.
Abstract: The objective of this paper is to investigate a new
approach based on the idea of pictograms for food portion size. This
approach adopts the model of the United States Pharmacopeia- Drug
Information (USP-DI). The representation of each food portion size
composed of three parts: frame, the connotation of dietary portion
sizes and layout. To investigate users- comprehension based on this
approach, two experiments were conducted, included 122 Taiwanese
people, 60 male and 62 female with ages between 16 and 64 (divided
into age groups of 16-30, 31-45 and 46-64). In Experiment 1, the mean
correcting rate of the understanding level of food items is 48.54%
(S.D.= 95.08) and the mean response time 2.89sec (S.D.=2.14). The
difference on the correct rates for different age groups is significant
(P*=0.00
Abstract: We propose a new approach on how to obtain the approximate solutions of Hamilton-Jacobi (HJ) equations. The process of the approximation consists of two steps. The first step is to transform the HJ equations into the virtual time based HJ equations (VT-HJ) by introducing a new idea of ‘virtual-time’. The second step is to construct the approximate solutions of the HJ equations through a computationally iterative procedure based on the VT-HJ equations. It should be noted that the approximate feedback solutions evolve by themselves as the virtual-time goes by. Finally, we demonstrate the effectiveness of our approximation approach by means of simulations with linear and nonlinear control problems.
Abstract: The problem of lot sizing, sequencing and scheduling
multiple products in flow line production systems has been studied
by several authors. Almost all of the researches in this area assumed
that setup times and costs are sequence –independent even though
sequence dependent setups are common in practice. In this paper we
present a new mixed integer non linear program (MINLP) and a
heuristic method to solve the problem in sequence dependent case.
Furthermore, a genetic algorithm has been developed which applies
this constructive heuristic to generate initial population. These two
proposed solution methods are compared on randomly generated
problems. Computational results show a clear superiority of our
proposed GA for majority of the test problems.