Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: An exploratory computational investigation using
RANS & URANS was carried out to understand the aerodynamics
around an isolatedsingle rotating wheel with decreasing ground
proximity. The wheel was initially modeled in free air conditions,
then with decreasing ground proximity and increased yaw angle with
rotational speeds. Three speeds of rotation were applied to the wheel
so that the effect of different angular velocities can be investigated. In
addition to rotation, three different yaw angles were applied to the
rotating wheel in order to understand how these two variables
combined affect the aerodynamic flow field around the wheel.
Abstract: Raw wood vinegar was purified by both standing and
filtering methods. Toxicity tests were conducted under laboratory
conditions by the topical application method (contact poison) and
feeding method (stomach poison). Larvicidal activities of wood
vinegar at four different concentrations (10, 15, 20, 25 and 30 %)
were studied against second instar larvae of housefly (Musca
domestica L.). Four replicates were maintained for all treatments and
controls. Larval mortality was recorded up to 96 hours and compared
with the larval survivability by two methods of larvicidal bioassay.
Percent pupation and percent adult emergence were observed in
treated M. domestica. The study revealed that the feeding method
gave higher efficiency compared with the topical application method.
Larval mortality increased with increasing concentration of wood
vinegar and the duration of exposure. No mortality was found in
treated M. domestica larvae at minimum 10% concentration of wood
vinegar through the experiments. The treated larvae were maintained
up to pupa and adult emergence. At 30% maximum concentration
larval duration was extended to 11 days in M. domestica for topical
application method and 9 days for feeding method. Similarly the
pupal durations were also increased with increased concentrations
(16 and 24 days for topical application method and feeding method
respectively at 30% concentration) of the treatments.
Abstract: This paper mainly proposes an efficient modified
particle swarm optimization (MPSO) method, to identify a slidercrank
mechanism driven by a field-oriented PM synchronous motor.
In system identification, we adopt the MPSO method to find
parameters of the slider-crank mechanism. This new algorithm is
added with “distance" term in the traditional PSO-s fitness function to
avoid converging to a local optimum. It is found that the comparisons
of numerical simulations and experimental results prove that the
MPSO identification method for the slider-crank mechanism is
feasible.
Abstract: To achieve reliable solutions, today-s numerical and
experimental activities need developing more accurate methods and
utilizing expensive facilities, respectfully in microchannels. The analytical
study can be considered as an alternative approach to alleviate
the preceding difficulties. Among the analytical solutions, those with
high robustness and low complexities are certainly more attractive.
The perturbation theory has been used by many researchers to analyze
microflows. In present work, a compressible microflow with constant
heat flux boundary condition is analyzed. The flow is assumed to be
fully developed and steady. The Mach and Reynolds numbers are also
assumed to be very small. For this case, the creeping phenomenon
may have some effect on the velocity profile. To achieve robustness
solution it is assumed that the flow is quasi-isothermal. In this study,
the creeping term which appears in the slip boundary condition
is formulated by different mathematical formulas. The difference
between this work and the previous ones is that the creeping term
is taken into account and presented in non-dimensionalized form.
The results obtained from perturbation theory are presented based
on four non-dimensionalized parameters including the Reynolds,
Mach, Prandtl and Brinkman numbers. The axial velocity, normal
velocity and pressure profiles are obtained. Solutions for velocities
and pressure for two cases with different Br numbers are compared
with each other and the results show that the effect of creeping
phenomenon on the velocity profile becomes more important when
Br number is less than O(ε).
Abstract: In this paper, a new Genetic Algorithm (GA) based
methodology is proposed to optimize the Degree of Hybridization
(DOH) in a passenger parallel hybrid car. At first step, target
parameters for the vehicle are decided and then using ADvanced
VehIcle SimulatOR (ADVISOR) software, the variation pattern of
these target parameters, across the different DOHs, is extracted. At
the next step, a suitable cost function is defined and is optimized
using GA. In this paper, also a new technique has been proposed for
deciding the number of battery modules for each DOH, which leads
to a great improvement in the vehicle performance. The proposed
methodology is so simple, fast and at the same time, so efficient.
Abstract: In textile industry, besides the conventional textile
products, technical textile goods, that have been brought external
functional properties into, are being developed for technical textile
industry. Especially these products produced with weaving
technology are widely preferred in areas such as sports, geology,
medical, automotive, construction and marine sectors. These textile
products are exposed to various stresses and large deformations under
typical conditions of use. At this point, sufficient and reliable data
could not be obtained with uniaxial tensile tests for determination of
the mechanical properties of such products due to mainly biaxial
stress state. Therefore, the most preferred method is a biaxial tensile
test method and analysis. These tests and analysis is applied to fabrics
with different functional features in order to establish the textile
material with several characteristics and mechanical properties of the
product. Planar biaxial tensile test, cylindrical inflation and bulge
tests are generally required to apply for textile products that are used
in automotive, sailing and sports areas and construction industry to
minimize accidents as long as their service life. Airbags, seat belts
and car tires in the automotive sector are also subject to the same
biaxial stress states, and can be characterized by same types of
experiments. In this study, in accordance with the research literature
related to the various biaxial test methods are compared. Results with
discussions are elaborated mainly focusing on the design of a biaxial
test apparatus to obtain applicable experimental data for developing a
finite element model. Sample experimental results on a prototype
system are expressed.
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: The aim of the present investigation was to compare
sex differences in thyroid gland structure of rabbits. Five adult male
and five adult female (3.1-3.5 kg body weight) New Zealand white
rabbits were used in the experiment. Results showed that at light
microscopic level, there was no sex difference in microscopic
appearance of the thyroid glands. At electron microscopic level,
however, the mitochondria and the microvilli of the follicular cells
are more numerous and the Golgi complex is also more extensive in
male rabbits in comparison to females. Results obtained from
micrometric measurements showed that the volume density of the
follicles is higher in males than in females, but the differences are not
statistically significant .The volume density of epithelium and the
height of follicular cells are significantly greater in males than in
females and reverse is true about the volume density of interstitium
(p
Abstract: In recent years, the underground water sources in
southern Taiwan have become salinized because of saltwater
intrusions. This study explores the adsorption characteristics of
activated carbon on salinizing inorganic salts using isothermal
adsorption experiments and provides a model analysis. The
temperature range for the isothermal adsorption experiments ranged
between 5 to 45 ℃, and the amount adsorbed varied between 28.21 to
33.87 mg/g. All experimental data of adsorption can be fitted to both
the Langmuir and the Freundlich models. The thermodynamic
parameters for per chlorate onto granular activated carbon were
calculated as -0.99 to -1.11 kcal/mol for DG°, -0.6 kcal/mol for DH°,
and 1.21 to 1.84 kcal/mol for DS°. This shows that the adsorption
process of granular activated carbon is spontaneously exothermic. The
observation of adsorption behaviors under low ionic strength, low pH
values, and low temperatures is beneficial to the adsorption removal of
perchlorate with granular activated carbon.
Abstract: Nuts are part of a healthy diet such as Mediterranean diet. Benefits of nuts in reducing the risk of heart disease has been reasonably attributed to their composition of vitamins, minerals, unsaturated fatty acids, fiber and phytochemicals such as polyphenols, tocopherols, squalene and phytosterols. More than 75% of total fatty acids of nuts are unsaturated. α- tocopherol is the main tocopherol isomer present in most of the nuts. While walnuts, Brazil nut, cashew nut, peanut, pecan and pistachio nuts are rich in γ- tocopherol. β- sitosterol is dominant sterol in nuts. Pistachio and pine nut have the highest total phytosterol and Brazil nut and English walnut the lowest. Walnuts also contain large amount of phenolic compounds compared with other nuts. Nuts are rich in compounds with antioxidant properties and their consumption can offer preventing from incidence of many diseases including cardiovascular.
Abstract: MMR vaccine failure had been reported globally and
here we report that it occurs now in India. Samples were collected from clinically suspected mumps cases were subjected for anti
mumps antibodies, virus isolation, RT-PCR, sequencing and
phylogenetic tree analysis. 56 samples collected from men and women belonging to various age groups. 30 had been vaccinated and
the status of 26 patients was unknown. 28 out of 30 samples were
found to be symptomatic and positive for Mumps IgM, indicating
active mumps infection in 93.4% of the vaccinated population. A
phylogenetic tree comparison of the clinical isolate is shown to be genotype C which is distinct from vaccine strain. Our study clearly sending warning signs that MMR vaccine is a failure and it needs to be revamped for the human use by increasing its efficacy and efficiency.
Abstract: As a part of routine oesophageal HDR Brachytherapy procedure, treatment planning takes about 45 minutes while patients are under light sedation. Some patients may suffer gagging and/or spasms before the 90-minute brachytherapy procedure complete, and the treatment may need to be aborted. A pre-prepared plan generated before patient’s sedation may reduce the brachytherapy procedure time by 40 minutes. This paper reports rationality and evidence of pre-prepared treatment plans. A retrospective study of 28 patients confirms that pre-prepared plans would be acceptable for all reviewed patients. The rationality is further confirmed by a systemic study with a wide range of applicator curvature and treatment volume. Detailed comparison between CT based treatment plans and pre-prepared plans are discussed. The argument holds for endobronchial HDR brachytherapy too. With the above evidence, pre-prepared plans have been used for all oesophageal and endobronchial HDR brachytherapy cases in our clinic.
Abstract: One of the major problems in genomic field is to perform sequence comparison on DNA and protein sequences. Executing sequence comparison on the DNA and protein data is a computationally intensive task. Sequence comparison is the basic step for all algorithms in protein sequences similarity. Parallel computing is an attractive solution to provide the computational power needed to speedup the lengthy process of the sequence comparison. Our main research is to enhance the protein sequence algorithm using dynamic programming method. In our approach, we parallelize the dynamic programming algorithm using multithreaded program to perform the sequence comparison and also developed a distributed protein database among many PCs using Remote Method Interface (RMI). As a result, we showed how different sizes of protein sequences data and computation of scoring matrix of these protein sequence on different number of processors affected the processing time and speed, as oppose to sequential processing.
Abstract: III-nitride quaternary InxAlyGa1-x-yN alloys have experienced considerable interest as potential materials for optoelectronic applications. Despite these interesting applications and the extensive efforts to understand their fundamental properties, research on its fundamental surface property, i.e., surface phonon polariton (SPP) has not yet been reported. In fact, the SPP properties have been shown to provide application for some photonic devices. Hence, there is an absolute need for thorough studies on the SPP properties of this material. In this work, theoretical study on the SPP modes in InAlGaN quaternary alloys are reported. Attention is focus on the wurtzite (α-) structure InxAlyGa1-x-yN semi-crystal with different In composition, x ranging from 0 to 0.10 and constant Al composition, y = 0.06. The SPP modes are obtained through the theoretical simulation by means of anisotropy model. The characteristics of SP dispersion curves are discussed. Accessible results in terms of the experimental point of view are also given. Finally, the results revealed that the SPP mode of α-InxAlyGa1-x-yN semiconductors exhibits two-mode behavior.
Abstract: The machining of Carbon Fiber Reinforced Plastics
has come to constitute a significant challenge for many fields of
industry. The resulting surface finish of machined parts is of primary
concern for several reasons, including contact quality and impact on
the assembly. Therefore, the characterization and prediction of
roughness based on machining parameters are crucial for costeffective
operations. In this study, a PCD tool comprised of two
straight flutes was used to trim 32-ply carbon fiber laminates in a bid
to analyze the effects of the feed rate and the cutting speed on the
surface roughness. The results show that while the speed has but a
slight impact on the surface finish, the feed rate for its part affects it
strongly. A detailed study was also conducted on the effect of fiber
orientation on surface roughness, for quasi-isotropic laminates used
in aerospace. The resulting roughness profiles for the four-ply
orientation lay-up were compared, and it was found that fiber angle is
a critical parameter relating to surface roughness. One of the four
orientations studied led to very poor surface finishes, and
characteristic roughness profiles were identified and found to only
relate to the ply orientations of multilayer carbon fiber laminates.
Abstract: This comparison of valuation techniques for bone age
assessment is a work carried out by the Telemedicine Research Group
of the Military University - TIGUM, as a preliminary to the Design
and development a treatment system of hand and wrist radiological
images for children aged 0-6 years to bone age assessment . In this
paper the techniques mentioned for decades have been the most
widely used and the statistically significant.
Althought, initially with the current project, it wants to work with
children who have limit age, this comparison and evaluation
techniques work will help in the future to expand the study subject in
the system to bone age assessment, implementing more techniques,
tools and deeper analysis to accomplish this purpose.
Abstract: The methodology of numerical simulation and calculation of aerodynamic characteristics of aircraft taking into account impact of wake on it has been developed. The results of numerical experiment in comparison with the data obtained in the wind tunnel are presented. Efficiency of methodology of calculation and the reliability of the results is shown.
Abstract: Foodborne Salmonella infections have become a
major problem world wide. Salmonellosis transmitted from fish are
quite common. Established quality control measures exist for export
oriented fish, none exists for fish consumed locally. This study aimed
at characterization of Salmonella isolated from Nile tilapia . The
study was carried out in selected beaches along L. Victoria in
Western Kenya between March and June 2007. One hundred and
twenty fish specimens were collected. Salmonella isolates were
confirmed using serotyping, biochemical testing in addition to malic
acid dehydrogenase (mdh) and fliC gene sequencing. Twenty
Salmonella isolates were confirmed by mdh gene sequencing. Nine
(9) were S. enterica serotype typhimurium, four (4) were S. enterica
Serotype, enteritidis and seven (7) were S. enterica serotype typhi.
Nile tilapia have a role in transmission of Salmonellosis in the study
area, poor sanitation was a major cause of pollution at the beach
inshore waters.
Abstract: Three batches of yogurts were made with soy protein
isolate (SPI) supplemented with 2% (S2), 4% (S4) or 6% (S6) of
skim milk powder (SMP). The fourth batch (control; S0) was
prepared from SPI without SMP supplementation. Lactobacillus
delbrueckii ssp. bulgaricus ATCC 11842 (Lb 11842) and
Streptococcus thermophilus ST 1342 (ST 1342) were used as the
starter culture. Biotransformation of the inactive forms, isoflavone
glycosides (IG) to biologically active forms, isoflavone aglycones
(IA), was determined during 28 d storage. The viability of both
microorganisms was significantly higher (P < 0.05) in S2, S4, and S6
than that in S0. The ratio of lactic acid/acetic acid in S0 was in the
range of 15.53 – 22.31 compared to 7.24 – 12.81 in S2, S4 and S6.
The biotransformation of IG to IA in S2, S4 and S6 was also
enhanced by 9.9 -13.3% compared to S0.