Abstract: Radio wave propagation on the road surface is a major
problem on wireless sensor network for traffic monitoring. In this
paper, we compare receiving signal strength on two scenarios 1) an
empty road and 2) a road with a vehicle. We investigate the effect of
antenna polarization and antenna height to the receiving signal
strength. The transmitting antenna is installed on the road surface.
The receiving signal is measured 360 degrees around the transmitting
antenna with the radius of 2.5 meters. Measurement results show the
receiving signal fluctuation around the transmitting antenna in both
scenarios. Receiving signal with vertical polarization antenna results
in higher signal strength than horizontal polarization antenna. The
optimum antenna elevation is 1 meter for both horizon and vertical
polarizations with the vehicle on the road. In the empty road, the
receiving signal level is unvarying with the elevation when the
elevation is greater than 1.5 meters.
Abstract: This paper considers the control of the longitudinal
flight dynamics of an F-16 aircraft. The primary design objective
is model-following of the pitch rate q, which is the preferred
system for aircraft approach and landing. Regulation of the aircraft
velocity V (or the Mach-hold autopilot) is also considered, but
as a secondary objective. The problem is challenging because the
system is nonlinear, and also non-affine in the input. A sliding
mode controller is designed for the pitch rate, that exploits the
modal decomposition of the linearized dynamics into its short-period
and phugoid approximations. The inherent robustness of the SMC
design provides a convenient way to design controllers without gain
scheduling, with a steady-state response that is comparable to that
of a conventional polynomial based gain-scheduled approach with
integral control, but with improved transient performance. Integral
action is introduced in the sliding mode design using the recently
developed technique of “conditional integrators", and it is shown that
robust regulation is achieved with asymptotically constant exogenous
signals, without degrading the transient response. Through extensive
simulation on the nonlinear multiple-input multiple-output (MIMO)
longitudinal model of the F-16 aircraft, it is shown that the conditional
integrator design outperforms the one based on the conventional linear
control, without requiring any scheduling.
Abstract: Missing data is a persistent problem in almost all
areas of empirical research. The missing data must be treated very
carefully, as data plays a fundamental role in every analysis.
Improper treatment can distort the analysis or generate biased results.
In this paper, we compare and contrast various imputation techniques
on missing data sets and make an empirical evaluation of these
methods so as to construct quality software models. Our empirical
study is based on NASA-s two public dataset. KC4 and KC1. The
actual data sets of 125 cases and 2107 cases respectively, without
any missing values were considered. The data set is used to create
Missing at Random (MAR) data Listwise Deletion(LD), Mean
Substitution(MS), Interpolation, Regression with an error term and
Expectation-Maximization (EM) approaches were used to compare
the effects of the various techniques.
Abstract: As computer network technology becomes
increasingly complex, it becomes necessary to place greater
requirements on the validity of developing standards and the
resulting technology. Communication networks are based on large
amounts of protocols. The validity of these protocols have to be
proved either individually or in an integral fashion. One strategy for
achieving this is to apply the growing field of formal methods.
Formal methods research defines systems in high order logic so that
automated reasoning can be applied for verification. In this research
we represent and implement a formerly announced multicast protocol
in Prolog language so that certain properties of the protocol can be
verified. It is shown that by using this approach some minor faults in
the protocol were found and repaired. Describing the protocol as
facts and rules also have other benefits i.e. leads to a process-able
knowledge. This knowledge can be transferred as ontology between
systems in KQML format. Since the Prolog language can increase its
knowledge base every time, this method can also be used to learn an
intelligent network.
Abstract: ZnO nanostructures including nanowires, nanorods,
and nanoneedles were successfully deposited on GaAs substrates,
respectively, by simple two-step chemical method for the first time. A
ZnO seed layer was firstly pre-coated on the O2-plasma treated
substrate by sol-gel process, followed by the nucleation of ZnO
nanostructures through hydrothermal synthesis. Nanostructures with
different average diameter (15-250 nm), length (0.9-1.8 μm), density
(0.9-16×109 cm-2) were obtained via adjusting the growth time and
concentration of precursors. From the reflectivity spectra, we
concluded ordered and taper nanostructures were preferential for
photovoltaic applications. ZnO nanoneedles with an average diameter
of 106 nm, a moderate length of 2.4 μm, and the density of 7.2×109
cm-2 could be synthesized in the concentration of 0.04 M for 18 h.
Integrated with the nanoneedle array, the power conversion efficiency
of single junction solar cell was increased from 7.3 to 12.2%,
corresponding to a 67% improvement.
Abstract: Present wireless communication demands compact and intelligent devices with multitasking capabilities at affordable cost. The focus in the presented paper is on a dual band antenna for wireless communication with the capability of operating at two frequency bands with same structure. Two resonance frequencies are observed with the second operation band at 4.2GHz approximately three times the first resonance frequency at 1.5GHz. Structure is simple loop of microstrip line with characteristic impedance 50 ohms. The proposed antenna is designed using defective ground structure (DGS) and shows the nearly one third reductions in size as compared to without DGS. This antenna was simulated on electromagnetic (EM) simulation software and fabricated using microwave integrated circuit technique on RT-Duroid dielectric substrate (εr= 2.22) of thickness (H=15 mils). The designed antenna was tested on automatic network analyzer and shows the good agreement with simulated results. The proposed structure is modeled into an equivalent electrical circuit and simulated on circuit simulator. Subsequently, theoretical analysis was carried out and simulated. The simulated, measured, equivalent circuit response, and theoretical results shows good resemblance. The bands of operation draw many potential applications in today’s wireless communication.
Abstract: Avoiding learning failures in mathematics e-learning environments caused by emotional problems in students with autism has become an important topic for combining of special education with information and communications technology. This study presents an adaptive emotional adjustment model in mathematics e-learning for students with autism, emphasizing the lack of emotional perception in mathematics e-learning systems. In addition, an emotion classification for students with autism was developed by inducing emotions in mathematical learning environments to record changes in the physiological signals and facial expressions of students. Using these methods, 58 emotional features were obtained. These features were then processed using one-way ANOVA and information gain (IG). After reducing the feature dimension, methods of support vector machines (SVM), k-nearest neighbors (KNN), and classification and regression trees (CART) were used to classify four emotional categories: baseline, happy, angry, and anxious. After testing and comparisons, in a situation without feature selection, the accuracy rate of the SVM classification can reach as high as 79.3-%. After using IG to reduce the feature dimension, with only 28 features remaining, SVM still has a classification accuracy of 78.2-%. The results of this research could enhance the effectiveness of eLearning in special education.
Abstract: This work aims to describe the process of developing
services and applications of seamless communication within a
Telecom Italia long-term research project, which takes as central aim
the design of a wearable communication device. In particular, the
objective was to design a wrist phone integrated into everyday life of
people in full transparency. The methodology used to design the
wristwatch was developed through several subsequent steps also
involving the Personas Layering Framework. The data collected in
this phases have been very useful for designing an improved version
of the first two concepts of wrist phone going to change aspects
related to the four critical points expressed by the users.
Abstract: Considering complexity of products, new geometrical
design and investment tolerances that are necessary, measuring and
dimensional controlling involve modern and more precise methods.
Photo digitizing method using two cameras to record pictures and
utilization of conventional method named “cloud points" and data
analysis by the use of ATOUS software, is known as modern and
efficient in mentioned context. In this paper, benefits of photo
digitizing method in evaluating sampling of machining processes
have been put forward. For example, assessment of geometrical
integrity surface in 5-axis milling process and measurement of
carbide tool wear in turning process, can be can be brought forward.
Advantages of this method comparing to conventional methods have
been expressed.
Abstract: An active suspension system has been proposed to
improve the ride comfort. A quarter-car 2 degree-of-freedom (DOF)
system is designed and constructed on the basis of the concept of a
four-wheel independent suspension to simulate the actions of an
active vehicle suspension system. The purpose of a suspension
system is to support the vehicle body and increase ride comfort. The
aim of the work described in the paper was to illustrate the
application of fuzzy logic technique to the control of a continuously
damping automotive suspension system. The ride comfort is
improved by means of the reduction of the body acceleration caused
by the car body when road disturbances from smooth road and real
road roughness.
The paper describes also the model and controller used in the
study and discusses the vehicle response results obtained from a
range of road input simulations. In the conclusion, a comparison of
active suspension fuzzy control and Proportional Integration
derivative (PID) control is shown using MATLAB simulations.
Abstract: To support user mobility for a wireless network new mechanisms are needed and are fundamental, such as paging, location updating, routing, and handover. Also an important key feature is mobile QoS offered by the WATM. Several ATM network protocols should be updated to implement mobility management and to maintain the already ATM QoS over wireless ATM networks. A survey of the various schemes and types of handover is provided. Handover procedure allows guarantee the terminal connection reestablishment when it moves between areas covered by different base stations. It is useful to satisfy user radio link transfer without interrupting a connection. However, failure to offer efficient solutions will result in handover important packet loss, severe delays and degradation of QoS offered to the applications. This paper reviews the requirements, characteristics and open issues of wireless ATM, particularly with regard to handover. It introduces key aspects of WATM and mobility extensions, which are added in the fixed ATM network. We propose a flexible approach for handover management that will minimize the QoS deterioration. Functional entities of this flexible approach are discussed in order to achieve minimum impact on the connection quality when a MT crosses the BS.
Abstract: Successful public-private-partnership (PPP)
implementation can not be achieved without the active participation of
private sector companies. This paper examines the decision-making of
private sector companies in public works delivered by the PPP model
on the basis of social responsibility theory. It proposes that private
sector companies should indentify objectives of entering into PPP
projects, and shoulder relevant social responsibilities, while a
minimum return should also be guaranteed in their favor, so as to
compensate for their assumed risk and support them to take on
responsibilities in the future. The paper also gives a calculation
regarding the appropriate scale and reasonable degree of private sector
involvement in PPP projects through the cost-benefit analysis in a
specific case study, with the purpose to guide the private sector
companies to create a cooperation environment resembling
“symbiosis" and facilitate the smooth implementation of public works
delivered by the PPP model.
Abstract: This paper presents the approach to design the Auto-
Tuning PID controller for interactive Water Level Process using
integral step response. The Integral Step Response (ISR) is the
method to model a dynamic process which can be done easily,
conveniently and very efficiently. Therefore this method is advantage
for design the auto tune PID controller. Our scheme uses the root
locus technique to design PID controller. In this paper MATLAB is
used for modeling and testing of the control system. The
experimental results of the interacting water level process can be
satisfyingly illustrated the transient response and the steady state
response.
Abstract: Simulation of occlusal function during laboratory
material-s testing becomes essential in predicting long-term
performance before clinical usage. The aim of the study was to assess
the influence of chamfer preparation depth on failure risk of heat
pressed ceramic crowns with and without zirconia framework by
means of finite element analysis. 3D models of maxillary central
incisor, prepared for full ceramic crowns with different depths of the
chamfer margin (between 0.8 and 1.2 mm) and 6-degree tapered
walls together with the overlying crowns were generated using
literature data (Fig. 1, 2). The crowns were designed with and
without a zirconia framework with a thickness of 0.4 mm. For all
preparations and crowns, stresses in the pressed ceramic crown,
zirconia framework, pressed ceramic veneer, and dentin were
evaluated separately. The highest stresses were registered in the
dentin. The depth of the preparations had no significant influence on
the stress values of the teeth and pressed ceramics for the studied
cases, only for the zirconia framework. The zirconia framework
decreases the stress values in the veneer.
Abstract: Due to the call of global warming effects, city planners aim at actions for reducing carbon emission. One of the approaches is to promote the usage of public transportation system toward the transit-oriented-development. For example, rapid transit system in Taipei city and Kaohsiung city are opening. However, until November 2008 the average daily patronage counted only 113,774 passengers at Kaohsiung MRT systems, much less than which was expected. Now the crucial questions: how the public transport competes with private transport? And more importantly, what factors would enhance the use of public transport? To give the answers to those questions, our study first applied regression to analyze the factors attracting people to use public transport around cities in the world. It is shown in our study that the number of MRT stations, city population, cost of living, transit fare, density, gasoline price, and scooter being a major mode of transport are the major factors. Subsequently, our study identified successful and unsuccessful cities in regard of the public transport usage based on the diagnosis of regression residuals. Finally, by comparing transportation strategies adopted by those successful cities, our conclusion stated that Kaohsiung City could apply strategies such as increasing parking fees, reducing parking spaces in downtown area, and reducing transfer time by providing more bus services and public bikes to promote the usage of public transport.
Abstract: In this paper we canvass three case studies of unique
research partnerships between universities and schools in the wider
community. In doing so, we consider those areas of indeterminate
zones of professional practice explored by academics in their
research activities within the wider community. We discuss three
cases: an artist-in-residence program designed to engage primary
school children with new understandings about local Indigenous
Australian issues in their pedagogical and physical landscapes; an
assessment of pedagogical concerns in relation to the use of physical
space in classrooms; and the pedagogical underpinnings of a
costumed museum school program. In doing so, we engage issues of
research as playing an integral part in the development,
implementation and maintenance of academic engagements with
wider community issues.
Abstract: Through 1980s, management accounting researchers
described the increasing irrelevance of traditional control and
performance measurement systems. The Balanced Scorecard (BSC)
is a critical business tool for a lot of organizations. It is a
performance measurement system which translates mission and
strategy into objectives. Strategy map approach is a development
variant of BSC in which some necessary causal relations must be
established. To recognize these relations, experts usually use
experience. It is also possible to utilize regression for the same
purpose. Structural Equation Modeling (SEM), which is one of the
most powerful methods of multivariate data analysis, obtains more
appropriate results than traditional methods such as regression. In the
present paper, we propose SEM for the first time to identify the
relations between objectives in the strategy map, and a test to
measure the importance of relations. In SEM, factor analysis and test
of hypotheses are done in the same analysis. SEM is known to be
better than other techniques at supporting analysis and reporting. Our
approach provides a framework which permits the experts to design
the strategy map by applying a comprehensive and scientific method
together with their experience. Therefore this scheme is a more
reliable method in comparison with the previously established
methods.
Abstract: The objective of this work which is based on the
approach of simultaneous engineering is to contribute to the
development of a CIM tool for the synthesis of functional design
dimensions expressed by average values and tolerance intervals. In
this paper, the dispersions method known as the Δl method which
proved reliable in the simulation of manufacturing dimensions is
used to develop a methodology for the automation of the simulation.
This methodology is constructed around three procedures. The first
procedure executes the verification of the functional requirements by
automatically extracting the functional dimension chains in the
mechanical sub-assembly. Then a second procedure performs an
optimization of the dispersions on the basis of unknown variables.
The third procedure uses the optimized values of the dispersions to
compute the optimized average values and tolerances of the
functional dimensions in the chains. A statistical and cost based
approach is integrated in the methodology in order to take account of
the capabilities of the manufacturing processes and to distribute
optimal values among the individual components of the chains.
Abstract: We investigate an asymmetric connections model with a
dynamic network formation process, using an agent based simulation.
We permit heterogeneity of agents- value. Valuable persons seem
to have many links on real social networks. We focus on this
point of view, and examine whether valuable agents change the
structures of the terminal networks. Simulation reveals that valuable
agents diversify the terminal networks. We can not find evidence that
valuable agents increase the possibility that star networks survive the
dynamic process. We find that valuable agents disperse the degrees
of agents in each terminal network on an average.
Abstract: This paper puts forward one kind of air-fuel ratio
control method with PI controller. With the help of
MATLAB/SIMULINK software, the mathematical model of air-fuel
ratio control system for distributorless CNG engine is constructed.
The objective is to maintain cylinder-to-cylinder air-fuel ratio at a
prescribed set point, determined primarily by the state of the Three-
Way-Catalyst (TWC), so that the pollutants in the exhaust are
removed with the highest efficiency. The concurrent control of airfuel
under transient conditions could be implemented by Proportional
and Integral (PI) controller. The simulation result indicates that the
control methods can easily eliminate the air/fuel maldistribution and
maintain the air/fuel ratio at the stochiometry within minimum
engine events.