Abstract: Dill (Anethum graveolens L.) is a popular herb used in
many regions, including Baltic countries. Dill is widely used for
flavoring foods and beverages due to its pleasant spicy aroma. The
aim of this work was to determine the best blanching method for
processing of dill prior to microwave vacuum drying based on
sensory properties, color and volatile compounds in dried product.
Two blanching mediums were used – water and steam, and for part of
samples microwave pretreatment was additionally used. Evaluation of
dried dill volatile aroma compounds, color changes and sensory
attributes was performed. Results showed that blanching significantly
influences the quality of dried dill. After evaluation of volatile aroma
compounds, color and sensory properties of microwave vacuum dried
dill, as the best method for dill pretreatment was established
blanching at 90 °C for 30 s.
Abstract: We examined whether children ( < 18 years old) had risk of intra-thoracic trauma during 'one-handed' chest compressions through MDCT images. We measured the length of the lower half of the sternum (Stotal/2~X). We also measured the distance from the diaphragm to the midpoint of the sternum (Stotal/2~D) and half the width of an adult hand (Wtotal/2). All the 1 year-old children had Stotal/2~X and Stotal/2~D less than Wtotal/2. Among the children aged 2 years, 6 (60.0%) had Stotal/2~X and Stotal/2~D less than Wtotal/2. Among those aged 3 years, 4 (26.7%) had Stotal/2~X and Stotal/2~D less than Wtotal/2, and among those aged 4 years, 2 (13.3%) had Stotal/2~X and Stotal/2~D less than Wtotal/2. However, Stotal/2~X and Stotal/2~D were greater than Wtotal/2 in children aged 5 years or more. We knew that small children may be at an increased risk of intra-thoracic trauma during 'one-handed' chest compressions.
Abstract: This research was conducted in the Lower Ping River
Basin downstream of the Bhumibol Dam and the Lower Wang River
Basin in Tak Province, Thailand. Most of the tributary streams of the
Ping can be considered as ungauged catchments. There are 10-
pumping station installation at both river banks of the Ping in Tak
Province. Recently, most of them could not fully operate due to the
water amount in the river below the level that would be pumping,
even though included water from the natural river and released flow
from the Bhumibol Dam. The aim of this research was to increase the
performance of those pumping stations using weir projects in the
Ping. Therefore, the river analysis system model (HEC-RAS) was
applied to study the hydraulic behavior of water surface profiles in
the Ping River with both cases of existing conditions and proposed
weirs during the violent flood in 2011 and severe drought in 2013.
Moreover, the hydrologic modeling system (HMS) was applied to
simulate lateral streamflow hydrograph from ungauged catchments of
the Ping. The results of HEC-RAS model calibration with existing
conditions in 2011 showed best trial roughness coefficient for the
main channel of 0.026. The simulated water surface levels fitted to
observation data with R2 of 0.8175. The model was applied to 3
proposed cascade weirs with 2.35 m in height and found surcharge
water level only 0.27 m higher than the existing condition in 2011.
Moreover, those weirs could maintain river water levels and increase
of those pumping performances during less river flow in 2013.
Abstract: Rhizopus oligosporus was used in the present study
for the production of protease enzyme under SSF. Sunflower meal
was used as by-product of oil industry incorporated with organic salts
was employed for the production of protease enzyme. The main
purpose of the present was to study different parameters of protease
productivity, its yields and to optimize basal fermentation conditions.
The optimal conditions found for protease production using
sunflower meal as a substrate in the present study were inoculum size
(1%), substrate (Sunflower meal), substrate concentration (20 g), pH
(3), cultivation period (72 h), incubation temperature (35oC),
substrate to diluent-s ratio (1:2) and tween 81 (1 mL). The maximum
production of protease in the presence of cheaper substrate at low
concentration and stability at acidic pH, these characteristics make
the strain and its enzymes useful in different industry.
Abstract: In this study we propose a novel monitor hydraulic
automatic gauge control (HAGC) system based on fuzzy feedforward
controller. This is used in the development of cold rolling
mill automation system to improve the quality of cold strip. According to features/ properties of entry steel strip like its average
yield stress, width of strip, and desired exit thickness, this controller realizes the compensation for the exit thickness error. The traditional methods of adjusting the roller position, can-t tolerate the variance in
the entry steel strip. The proposed method uses a mathematical model
of the system together with the expert knowledge to perform this adjustment while minimizing the effect of the stated problem. In
order to improve the speed of the controller in rejecting disturbances
introduced by entry strip thickness variations, expert knowledge is added as a feed-forward term to the HAGC system. Simulation
results for the application of the proposed controller to a real cold mill show that the exit strip quality is highly improved.
Abstract: The paper investigates parallel channel instabilities of
natural circulation boiling water reactor. A thermal-hydraulic model
is developed to simulate two-phase flow behavior in the natural circulation boiling water reactor (NCBWR) with the incorporation of
ex-core components and recirculation loop such as steam separator, down-comer, lower-horizontal section and upper-horizontal section
and then, numerical analysis is carried out for parallel channel
instabilities of the reactor undergoing both in-phase and out-of-phase
modes of oscillations. To analyze the relative effect on stability of the reactor due to inclusion of various ex-core components and
recirculation loop, marginal stable point is obtained at a particular inlet enthalpy of the reactor core without the inclusion of ex-core
components and recirculation loop and then with the inclusion of the
same. Numerical simulations are also conducted to determine the
relative dominance between two modes of oscillations i.e. in-phase and out-of-phase. Simulations are also carried out when the channels
are subjected to asymmetric power distribution keeping the inlet enthalpy same.
Abstract: Combining energy efficiency with renewable energy
sources constitutes a key strategy for a sustainable future. The wind
power sector stands out as a fundamental element for the
achievement of the European renewable objectives and Portugal is no
exception to the increase of the wind energy for the electricity
generation. This work proposes an optimization model for the long
range electricity power planning in a system similar to the
Portuguese one, where the expected impacts of the increasing
installed wind power on the operating performance of thermal power
plants are taken into account. The main results indicate that the
increasing penetration of wind power in the electricity system will
have significant effects on the combined cycle gas power plants
operation and on the theoretically expected cost reduction and
environmental gains. This research demonstrated the need to address
the impact that energy sources with variable output may have, not
only on the short-term operational planning, but especially on the
medium to long range planning activities, in order to meet the
strategic objectives for the energy sector.
Abstract: Hazard rate estimation is one of the important topics
in forecasting earthquake occurrence. Forecasting earthquake
occurrence is a part of the statistical seismology where the main
subject is the point process. Generally, earthquake hazard rate is
estimated based on the point process likelihood equation called the
Hazard Rate Likelihood of Point Process (HRLPP). In this research,
we have developed estimation method, that is hazard rate single
decrement HRSD. This method was adapted from estimation method
in actuarial studies. Here, one individual associated with an
earthquake with inter event time is exponentially distributed. The
information of epicenter and time of earthquake occurrence are used
to estimate hazard rate. At the end, a case study of earthquake hazard
rate will be given. Furthermore, we compare the hazard rate between
HRLPP and HRSD method.
Abstract: This work describes a CACSD tool for automatic design of robust controllers for hydraulic turbines. The tool calculates the optimal controller using the MATLAB hinfopt function and it
serves as a practical and effective solution for the laborious task of
designing a different controller for each type of turbine and generator, and different parameters and conditions of the plant. Results of the simulation of a generating unit subject to parameters
variation show the accuracy and efficiency of the obtained robust
controllers.
Abstract: This paper presents the new results of energy plant –
rye and triticale at yellow ripeness and ripe, pre-treatment in high
pressure steam reactor and monosaccharide extraction. There were
investigated the influence of steam pressure (20 to 22 bar), retention
duration (180 to 240 s) and catalytic sulphuric acid concentration
strength (0 to 0.5 %) on the pre-treatment process, contents of
monosaccharides (glucose, arabinose, xylose, mannose) and
undesirable by-compounds (furfural and HMF) in the reactor. The
study has determined that the largest amount of monosaccharides
(37.2 % of glucose, 2.7 % of arabinose, 8.4 % of xylose, and 1.3 %
of mannose) was received in the rye at ripe, the samples of which
were mixed with 0.5 % concentration of catalytic sulphuric acid, and
hydrolysed in the reactor, where the pressure was 20 bar, whereas the
reaction time – 240 s.
Abstract: The river flow forecasting represents a crucial point to employ for improving a management policy addressed to the right use of water resources as well as for conjugating prevention and defense actions against environmental degradation. The difficulties occurring during the field activities encourage the development and implementation of operative computation and measuring methods addressed to time reduction for data acquisition and processing maintaining a good level of accuracy. Therefore, the aim of the present work is to test a new entropy based expeditive methodology for the evaluation of the rating curves on three gauged sections with different geometric and morphological characteristics. The methodology requires the choice of only three verticals along the measure section and the sampling of only the maximum velocity. The results underline how in most conditions the rating curves drawn can replace those built with classic methodologies, simplifying thus the procedures of data monitoring and calculation.
Abstract: Threedimensional numerical simulations are conducted on a full scale CANDU Moderator and Transient variations of the temperature and velocity distributions inside the tank are determined. The results show that the flow and temperature distributions inside the moderator tank are three dimensional and no symmetry plane can be identified.Competition between the upward moving buoyancy driven flows and the downward moving momentum driven flows, results in the formation of circulation zones. The moderator tank operates in the buoyancy driven mode and any small disturbances in the flow or temperature makes the system unstable and asymmetric. Different types of temperature fluctuations are noted inside the tank: (i) large amplitude are at the boundaries between the hot and cold (ii) low amplitude are in the core of the tank (iii) high frequency fluctuations are in the regions with high velocities and (iv) low frequency fluctuations are in the regions with lower velocities.
Abstract: Identifying protein coding regions in DNA sequences is a basic step in the location of genes. Several approaches based on signal processing tools have been applied to solve this problem, trying to achieve more accurate predictions. This paper presents a new predictor that improves the efficacy of three techniques that use the Fourier Transform to predict coding regions, and that could be computed using an algorithm that reduces the computation load. Some ideas about the combination of the predictor with other methods are discussed. ROC curves are used to demonstrate the efficacy of the proposed predictor, based on the computation of 25 DNA sequences from three different organisms.
Abstract: This paper seeks to give a general idea of the universe of project portfolio management, from its multidisciplinary nature, to the many challenges it raises, passing through the different techniques, models and tools used to solve the multiple problems known. It is intended to contribute to the clarification, with great depth, of the impacts and relationships involved in managing the projects- portfolio. It aims at proposing a technique for the project alignment with the organisational strategy, in order to select projects that later on will be considered in the analysis and selection of the portfolio. We consider the development of a methodology for assessing the project alignment index very relevant in the global market scenario. It can help organisations to gain a greater awareness of market dynamics, speed up the decision process and increase its consistency, thus enabling the strategic alignment and the improvement of the organisational performance.
Abstract: Today, money laundering (ML) poses a serious threat
not only to financial institutions but also to the nation. This criminal
activity is becoming more and more sophisticated and seems to have
moved from the cliché of drug trafficking to financing terrorism and
surely not forgetting personal gain. Most international financial
institutions have been implementing anti-money laundering solutions
(AML) to fight investment fraud. However, traditional investigative
techniques consume numerous man-hours. Recently, data mining
approaches have been developed and are considered as well-suited
techniques for detecting ML activities. Within the scope of a
collaboration project for the purpose of developing a new solution for
the AML Units in an international investment bank, we proposed a
data mining-based solution for AML. In this paper, we present a
heuristics approach to improve the performance for this solution. We
also show some preliminary results associated with this method on
analysing transaction datasets.
Abstract: In this report we present a rule-based approach to
detect anomalous telephone calls. The method described here uses
subscriber usage CDR (call detail record) data sampled over two
observation periods: study period and test period. The study period
contains call records of customers- non-anomalous behaviour.
Customers are first grouped according to their similar usage
behaviour (like, average number of local calls per week, etc). For
customers in each group, we develop a probabilistic model to describe
their usage. Next, we use maximum likelihood estimation (MLE) to
estimate the parameters of the calling behaviour. Then we determine
thresholds by calculating acceptable change within a group. MLE is
used on the data in the test period to estimate the parameters of the
calling behaviour. These parameters are compared against thresholds.
Any deviation beyond the threshold is used to raise an alarm. This
method has the advantage of identifying local anomalies as compared
to techniques which identify global anomalies. The method is tested
for 90 days of study data and 10 days of test data of telecom
customers. For medium to large deviations in the data in test window,
the method is able to identify 90% of anomalous usage with less than
1% false alarm rate.
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.
Abstract: In the meat processing industry the substitution of
meat with non-meat ingredients is considered an important strategy
for reducing overall production costs. The main purpose of the
current research was to evaluate differences in physical-chemical
composition of cooked sausage with different legumes additions.
Peas (Pisum sativum), beans (Phaseolus vulgaris) and lentil (Lens
culinaris) were used in preparation of sausages. The legumes at
proportion of 20% of the total weight of meat were added in
sausages. The whole ingredients were mixed, filled into casing,
compressed, cooked and cooled. After storage the samples were
sensory evaluated. The sensory evaluation was carried out using the
nine point hedonic scale and line scale. Sausages without legumes
flour was used as control sample. The main conclusion of the current
research the legumes flour can be successfully used for cooked
sausages production.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: In the present study, we aimed to design the
intrauterine and extrauterine exposure to 1800 MHz GSM-like RF
radiation and investigate its possible bio-effects on infant female
rabbits. Totally thirty-six New Zealand White female rabbits, onemonth
old, were randomly divided into four groups which are
composed of 9 rabbits; i. Group I [Intrauterine (IU) exposure(-);
Extrauterine (EU) exposure (-)], Group II [IU exposure (-); EU
exposure (+)], Group III [IU exposure(+);EU exposure(-)], Group IV
[IU exposure (+);EU exposure(+)]. The master regulatory enzymes
activities of pentose phosphate pathway (glucose-6-phosphate
dehydrogenase, G-6PD; 6-phosphogluconate dehydrogenase, 6-
PGDH) and glutathione-dependent metabolism (glutathione
peroxidase, GSH-Px; glutathione reductase, GR; glutathione Stransferase,
GST, thioredoxin reductase, TRx) were analyzed in liver
tissues of young female rabbits. Decreased G-6PD, 6-PGD, GSH-Px,
GR activities were found in Group III compared to Group I (p