Abstract: DNA shuffling is a powerful method used for in vitro
evolute molecules with specific functions and has application in areas
such as, for example, pharmaceutical, medical and agricultural
research. The success of such experiments is dependent on a variety
of parameters and conditions that, sometimes, can not be properly
pre-established. Here, two computational models predicting DNA
shuffling results is presented and their use and results are evaluated
against an empirical experiment. The in silico and in vitro results
show agreement indicating the importance of these two models and
motivating the study and development of new models.
Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: The main goal of this paper is to study Statistical Process Control (SPC) with Exponentially Weighted Moving Average (EWMA) control chart when observations are serially-correlated. The characteristic of control chart is Average Run Length (ARL) which is the average number of samples taken before an action signal is given. Ideally, an acceptable ARL of in-control process should be enough large, so-called (ARL0). Otherwise it should be small when the process is out-of-control, so-called Average of Delay Time (ARL1) or a mean of true alarm. We find explicit formulas of ARL for EWMA control chart for Seasonal Autoregressive and Moving Average processes (SARMA) with Exponential white noise. The results of ARL obtained from explicit formula and Integral equation are in good agreement. In particular, this formulas for evaluating (ARL0) and (ARL1) be able to get a set of optimal parameters which depend on smoothing parameter (λ) and width of control limit (H) for designing EWMA chart with minimum of (ARL1).
Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: A systems approach model for prostate cancer in prostate duct, as a sub-system of the organism is developed. It is accomplished in two steps. First this research work starts with a nonlinear system of coupled Fokker-Plank equations which models continuous process of the system like motion of cells. Then extended to PDEs that include discontinuous processes like cell mutations, proliferation and deaths. The discontinuous processes is modeled by using intensity poisson processes. The model incorporates the features of the prostate duct. The system of PDEs spatial coordinate is along the proximal distal axis. Its parameters depend on features of the prostate duct. The movement of cells is biased towards distal region and mutations of prostate cancer cells is localized in the proximal region. Numerical solutions of the full system of equations are provided, and are exhibit traveling wave fronts phenomena. This motivates the use of the standard transformation to derive a canonically related system of ODEs for traveling wave solutions. The results obtained show persistence of prostate cancer by showing that the non-negative cone for the traveling wave system is time invariant. The traveling waves have a unique global attractor is proved also. Biologically, the global attractor verifies that evolution of prostate cancer stem cells exhibit the avascular tumor growth. These numerical solutions show that altering prostate stem cell movement or mutation of prostate cancer cells lead to avascular tumor. Conclusion with comments on clinical implications of the model is discussed.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: To evaluate the ability to predict xerostomia after
radiotherapy, we constructed and compared neural network and
logistic regression models. In this study, 61 patients who completed a
questionnaire about their quality of life (QoL) before and after a full
course of radiation therapy were included. Based on this questionnaire,
some statistical data about the condition of the patients’ salivary
glands were obtained, and these subjects were included as the inputs of
the neural network and logistic regression models in order to predict
the probability of xerostomia. Seven variables were then selected from
the statistical data according to Cramer’s V and point-biserial
correlation values and were trained by each model to obtain the
respective outputs which were 0.88 and 0.89 for AUC, 9.20 and 7.65
for SSE, and 13.7% and 19.0% for MAPE, respectively. These
parameters demonstrate that both neural network and logistic
regression methods are effective for predicting conditions of parotid
glands.
Abstract: In this study, active tendons with Proportional Integral
Derivation type controllers were applied to a SDOF and a MDOF
building model. Physical models of buildings were constituted with
virtual springs, dampers and rigid masses. After that, equations of
motion of all degrees of freedoms were obtained. Matlab Simulink
was utilized to obtain the block diagrams for these equations of
motion. Parameters for controller actions were found by using a trial
method. After earthquake acceleration data were applied to the
systems, building characteristics such as displacements, velocities,
accelerations and transfer functions were analyzed for all degrees of
freedoms. Comparisons on displacement vs. time, velocity vs. time,
acceleration vs. time and transfer function (Db) vs. frequency (Hz)
were made for uncontrolled and controlled buildings. The results
show that the method seems feasible.
Abstract: In this study thermodynamic performance analysis of a
combined organic Rankine cycle and ejector refrigeration cycle is
carried out for use of low-grade heat source in the form of sensible
energy. Special attention is paid to the effects of system parameters
including the turbine inlet temperature and turbine inlet pressure on the
characteristics of the system such as ratios of mass flow rate, net work
production, and refrigeration capacity as well as the coefficient of
performance and exergy efficiency of the system. Results show that
for a given source the coefficient of performance increases with
increasing of the turbine inlet pressure. However, the exergy
efficiency has an optimal condition with respect to the turbine inlet
pressure.
Abstract: Sputum smear conversion after one month of antituberculosis
therapy in new smear positive pulmonary tuberculosis
patients (PTB+) is a vital indicator towards treatment success. The
objective of this study is to determine the rate of sputum smear
conversion in new PTB+ patients after one month under treatment of
National Institute of Diseases of the Chest and Hospital (NIDCH).
Analysis of sputum smear conversion was done by re-clinical
examination with sputum smear microscopic test after one month.
Socio-demographic and hematological parameters were evaluated to
perceive the correlation with the disease status. Among all enrolled
patients only 33.33% were available for follow up diagnosis and of
them only 42.86% patients turned to smear negative. Probably this
consequence is due to non-coherence to the proper disease
management. 66.67% and 78.78% patients reported low haemoglobin
and packed cell volume level respectively whereas 80% and 93.33%
patients accounted accelerated platelet count and erythrocyte
sedimentation rate correspondingly.
Abstract: Camera calibration is an indispensable step for augmented
reality or image guided applications where quantitative information
should be derived from the images. Usually, a camera
calibration is obtained by taking images of a special calibration object
and extracting the image coordinates of projected calibration marks
enabling the calculation of the projection from the 3d world coordinates
to the 2d image coordinates. Thus such a procedure exhibits
typical steps, including feature point localization in the acquired
images, camera model fitting, correction of distortion introduced by
the optics and finally an optimization of the model-s parameters. In
this paper we propose to extend this list by further step concerning
the identification of the optimal subset of images yielding the smallest
overall calibration error. For this, we present a Monte Carlo based
algorithm along with a deterministic extension that automatically
determines the images yielding an optimal calibration. Finally, we
present results proving that the calibration can be significantly
improved by automated image selection.
Abstract: This paper deals with the conceptual design of the
new aeroelastic demonstrator for the whirl flutter simulation. The
paper gives a theoretical background of the whirl flutter phenomenon
and describes the events of the whirl flutter occurrence in the
aerospace practice. The second part is focused on the experimental
research of the whirl flutter on aeroelastic similar models. Finally the
concept of the new aeroelastic demonstrator is described. The
demonstrator represents the wing and engine of the twin turboprop
commuter aircraft including a driven propeller. It allows the changes
of the main structural parameters influencing the whirl flutter
stability characteristics. It is intended for the experimental
investigation of the whirl flutter in the wind tunnel. The results will
be utilized for validation of analytical methods and software tools.
Abstract: In present work, drying characteristics of fresh papaya (Carica papaya L.) was studied to understand the dehydration process and its behavior. Drying experiments were carried out by a laboratory scaled microwave-vacuum oven. The parameters affecting drying characteristics including operating modes (continuous, pulsed), microwave power (400 and 800 W), and vacuum pressure (20, 30, and 40 cmHg) were investigated. For pulsed mode, two levels of power-off time (60 and 120 s) were used while the power-on time was fixed at 60 s and the vacuum pressure was fixed at 40 cmHg. For both operating modes, the effects of drying conditions on drying time, drying rate, and effective diffusivity were investigated. The results showed high microwave power, high vacuum, and pulsed mode of 60 s-on/60 s-off favored drying rate as shown by the shorten drying time and increased effective diffusivity. The drying characteristics were then described by Page-s model, which showed a good agreement with experimental data.
Abstract: Based on the feature of model disturbances and uncertainty being compensated dynamically in auto – disturbances-rejection-controller (ADRC), a new method using ADRC is proposed for the decoupling control of dispenser longitudinal movement in big flight envelope. Developed from nonlinear model directly, ADRC is especially suitable for dynamic model that has big disturbances. Furthermore, without changing the structure and parameters of the controller in big flight envelope, this scheme can simplify the design of flight control system. The simulation results in big flight envelope show that the system achieves high dynamic performance, steady state performance and the controller has strong robustness.
Abstract: Fuel and oxidant gas delivery plate, or fuel cell
plate, is a key component of a Proton Exchange Membrane (PEM)
fuel cell. To manufacture low-cost and high performance fuel cell
plates, advanced computer modeling and finite element structure
analysis are used as virtual prototyping tools for the optimization
of the plates at the early design stage. The present study examines
thermal stress analysis of the fuel cell plates that are produced
using a patented, low-cost fuel cell plate production technique
based on screen-printing. Design optimization is applied to
minimize the maximum stress within the plate, subject to strain
constraint with both geometry and material parameters as design
variables. The study reveals the characteristics of the printed
plates, and provides guidelines for the structure and material design
of the fuel cell plate.
Abstract: The purpose of this study was to evaluate and
compare new indices based on the discrete wavelet transform
with another spectral parameters proposed in the literature as
mean average voltage, median frequency and ratios between
spectral moments applied to estimate acute exercise-induced
changes in power output, i.e., to assess peripheral muscle
fatigue during a dynamic fatiguing protocol. 15 trained
subjects performed 5 sets consisting of 10 leg press, with 2
minutes rest between sets. Surface electromyography was
recorded from vastus medialis (VM) muscle. Several surface
electromyographic parameters were compared to detect
peripheral muscle fatigue. These were: mean average voltage
(MAV), median spectral frequency (Fmed), Dimitrov spectral
index of muscle fatigue (FInsm5), as well as other five
parameters obtained from the discrete wavelet transform
(DWT) as ratios between different scales. The new wavelet
indices achieved the best results in Pearson correlation
coefficients with power output changes during acute dynamic
contractions. Their regressions were significantly different
from MAV and Fmed. On the other hand, they showed the
highest robustness in presence of additive white gaussian
noise for different signal to noise ratios (SNRs). Therefore,
peripheral impairments assessed by sEMG wavelet indices
may be a relevant factor involved in the loss of power output
after dynamic high-loading fatiguing task.
Abstract: Fuzzy logic control (FLC) systems have been tested in
many technical and industrial applications as a useful modeling tool
that can handle the uncertainties and nonlinearities of modern control
systems. The main drawback of the FLC methodologies in the
industrial environment is challenging for selecting the number of
optimum tuning parameters.
In this paper, a method has been proposed for finding the optimum
membership functions of a fuzzy system using particle swarm
optimization (PSO) algorithm. A synthetic algorithm combined from
fuzzy logic control and PSO algorithm is used to design a controller
for a continuous stirred tank reactor (CSTR) with the aim of
achieving the accurate and acceptable desired results. To exhibit the
effectiveness of proposed algorithm, it is used to optimize the
Gaussian membership functions of the fuzzy model of a nonlinear
CSTR system as a case study. It is clearly proved that the optimized
membership functions (MFs) provided better performance than a
fuzzy model for the same system, when the MFs were heuristically
defined.
Abstract: In this research, the diabetes conditions of people (healthy, prediabete and diabete) were tried to be identified with noninvasive palm perspiration measurements. Data clusters gathered from 200 subjects were used (1.Individual Attributes Cluster and 2. Palm Perspiration Attributes Cluster). To decrase the dimensions of these data clusters, Principal Component Analysis Method was used. Data clusters, prepared in that way, were classified with Support Vector Machines. Classifications with highest success were 82% for Glucose parameters and 84% for HbA1c parametres.
Abstract: The microbiological and physicochemical
characteristics of wetland soils in Eket Local Government Area were
studied between May 2001 and June 2003. Total heterotrophic
bacterial counts (THBC), total fungal counts (TFC), and total
actinomycetes counts (TAC) were determined from soil samples
taken from four locations at two depths in the wet and dry seasons.
Microbial isolates were characterized and identified. Particle size and
chemical parameters were also determined using standard methods.
THBC ranged from 5.2 (+0.17) x106 to 1.7 (+0.18) x107 cfu/g and
from 2.4 (+0.02) x106 to 1.4 (+0.04) x107cfu/g in the wet and dry
seasons, respectively. TFC ranged from 1.8 (+0.03) x106 to 6.6 (+
0.18) x106 cfu/g and from 1.0 (+0.04) x106 to 4.2 (+ 0.01) x106 cfu/g
in the wet and dry seasons, respectively .TAC ranged from 1.2
(+0.53) x106 to 6.0 (+0.05) x106 cfu/g and from 0.6 (+0.01) x106 to
3.2 (+ 0.12) x106 cfu/g in the wet and dry season, respectively.
Acinetobacter, Alcaligenes, Arthrobacter, Bacillus, Beijerinckja,
Enterobacter, Micrococcus, Flavobacterium, Serratia, Enterococcus,
and Pseudomonas species were predominant bacteria while
Aspergillus, Fusarium, Mucor, Penicillium, and Rhizopus were the
dominant fungal genera isolated. Streptomyces and Norcadia were
the actinomycetes genera isolated. The particle size analysis showed
high sand fraction but low silt and clay. The pH and % organic
matter were generally acidic and low, respectively at all locations.
Calcium dominated the exchangeable bases with low electrical
conductivity and micronutrients. These results provide the baseline
data of Eket wetland soils for its management for sustainable
agriculture.