Abstract: Three sulphonic acid-doped polyanilines were
synthesized through chemical oxidation at low temperature (0-5 oC)
and potential of these polymers as sensing agent for O2 gas detection
in terms of fluorescence quenching was studied. Sulphuric acid,
dodecylbenzene sulphonic acid (DBSA) and camphor sulphonic acid
(CSA) were used as doping agents. All polymers obtained were dark
green powder. Polymers obtained were characterized by Fourier
transform infrared spectroscopy, ultraviolet-visible absorption
spectroscopy, thermogravimetry analysis, elemental analysis,
differential scanning calorimeter and gel permeation
chromatography. Characterizations carried out showed that polymers
were successfully synthesized with mass recovery for sulphuric aciddoped
polyaniline (SPAN), DBSA-doped polyaniline (DBSA-doped
PANI) and CSA-doped polyaniline (CSA-doped PANI) of 71.40%,
75.00% and 39.96%, respectively. Doping level of SPAN, DBSAdoped
PANI and CSA-doped PANI were 32.86%, 33.13% and
53.96%, respectively as determined based on elemental analysis.
Sensing test was carried out on polymer sample in the form of
solution and film by using fluorescence spectrophotometer. Samples
of polymer solution and polymer film showed positive response
towards O2 exposure. All polymer solutions and films were fully
regenerated by using N2 gas within 1 hour period. Photostability
study showed that all samples of polymer solutions and films were
stable towards light when continuously exposed to xenon lamp for 9
hours. The relative standard deviation (RSD) values for SPAN
solution, DBSA-doped PANI solution and CSA-doped PANI
solution for repeatability were 0.23%, 0.64% and 0.76%,
respectively. Meanwhile RSD values for reproducibility were 2.36%,
6.98% and 1.27%, respectively. Results for SPAN film, DBSAdoped
PANI film and CSA-doped PANI film showed the same
pattern with RSD values for repeatability of 0.52%, 4.05% and
0.90%, respectively. Meanwhile RSD values for reproducibility were
2.91%, 10.05% and 7.42%, respectively. The study on effect of the
flow rate on response time was carried out using 3 different rates
which were 0.25 mL/s, 1.00 mL/s and 2.00 mL/s. Results obtained
showed that the higher the flow rate, the shorter the response time.
Abstract: This work contains information about the influence low-level optical irradiation on sperm motility of sturgeon fish. On the basis of given and earlier received data the following conclusion has been made. Among the photophysical processes of a resonant and not resonant nature (oriented action of light; action of gradient forces; dipole-dipole interaction; termooptical processes), which are capable to cause the photobiological effects depended on such laserspecific characteristics as polarization and coherency, determining influence belongs to oriented action of light and dipole-dipole interactions among the processes studied in the present work.
Abstract: This study was aimed to explain the influence of surface roughness of the drawbead on non-symmetry deep drawing cold rolled steel sheet to improve the drawability of cold rolled steel sheet. The variables used in this study included semi-circle drawbead with 3 levels of surface roughness which are 6.127 mm Ra, 0.963 mm Ra and 0.152 mm Ra and cold rolled steel sheet according to 3 grades of the JIS standards which are SPCC, SPCE and SPCD with the thickness of 1.0 mm and the blankholder force which is 50% of the drawing force and the depth of 50 mm. According to the test results, when there was the increase in the surface roughness of drawbead, there would be the increase in deep drawing force, especially the SPCC cold rolled steel sheet. This is similar to the increase in the equivalent strain and the wall thickness distribution when the surface roughness of the drawbead increased. It could be concluded that the surface roughness of drawbead has an influence on deep drawing cold rolled steel sheet, especially the drawing force, the equivalent strain and the wall thickness distribution.
Abstract: This study investigates the relationships between
Work Motivation, Work Stress, and Job Satisfaction toward
cross-strait employees. The target subjects are three
manufacturing firms in Mainland China and Taiwan. Out of 450
distributed surveys, 352 valid surveys were obtained with the
response rate of 78.22%.The findings have addressed three main
pull factors toward cross-strait employees in choosing jobs, which
are (1) high level of firm stability, (2) good firm image, and (3)
good employee benefits. In addition, various employee attributes
exert different impacts on Work Motivation, Work Stress, and
Job Satisfaction. The comparison between expected and actual
perceived Job Satisfaction toward cross-strait employees shows
that “salary" ranks highest regarding expected Job Satisfaction
whereas “co-worker relationship" ranks highest regarding actual
perceived Job Satisfaction, which implies actual perceived Job
Satisfaction do not match employee expectations. Therefore, this
research further concludes that there exists differences between
employees- expected and actual perceived Job Satisfaction.
Abstract: A four element prototype phased array surface probe
has been designed and constructed to improve clinical human
prostate spectroscopic data. The probe consists of two pairs of
adjacent rectangular coils with an optimum overlap to reduce the
mutual inductance. The two pairs are positioned on the anterior and
the posterior pelvic region and two couples of varactors at the input
of each coil undertake the procedures of tuning and matching. The
probe switches off and on automatically during the consecutive
phases of the MR experiment with the use of an analog switch that is
triggered by a microcontroller. Experimental tests that were carried
out resulted in high levels of tuning accuracy. Also, the switching
mechanism functions properly for various applied loads and pulse
sequence characteristics, producing only 10 μs of latency.
Abstract: This study examined the role of driving experience in hazard perception and categorization using traffic scene pictures. Specifically, young-inexperienced, moderately experienced and very experienced (taxi) drivers observed traffic scene pictures while connected to an eye tracking system and were asked to rate the level of hazardousness of each picture and to mention the three most prominent hazards in it. Target pictures included nine, nearly identical, pairs of pictures where one picture in each pair included an actual hazard as an additional element. Altogether, 22 areas of interest (AOIs) were predefined and included 13 potential hazards and 9 actual hazards. Data analysis included both verbal reports and eye scanning patterns of these AOIs. Generally, both experienced and taxi drivers noted a relatively larger number of potential hazards than young inexperienced drivers Thus, by relating to less salient potential hazards, experienced drivers have demonstrated a better situation model of the traffic environment.
Abstract: The sanitary sewerage connection rate becomes an
important indicator of advanced cities. Following the construction of
sanitary sewerages, the maintenance and management systems are
required for keeping pipelines and facilities functioning well. These
maintenance tasks often require sewer workers to enter the manholes
and the pipelines, which are confined spaces short of natural
ventilation and full of hazardous substances. Working in sewers could
be easily exposed to a risk of adverse health effects. This paper
proposes the use of Bayesian belief networks (BBN) as a higher level
of noncarcinogenic health risk assessment of sewer workers. On the
basis of the epidemiological studies, the actual hospital attendance
records and expert experiences, the BBN is capable of capturing the
probabilistic relationships between the hazardous substances in sewers
and their adverse health effects, and accordingly inferring the
morbidity and mortality of the adverse health effects. The provision of
the morbidity and mortality rates of the related diseases is more
informative and can alleviate the drawbacks of conventional methods.
Abstract: The security of power systems against malicious cyberphysical
data attacks becomes an important issue. The adversary
always attempts to manipulate the information structure of the power
system and inject malicious data to deviate state variables while
evading the existing detection techniques based on residual test. The
solutions proposed in the literature are capable of immunizing the
power system against false data injection but they might be too costly
and physically not practical in the expansive distribution network.
To this end, we define an algebraic condition for trustworthy power
system to evade malicious data injection. The proposed protection
scheme secures the power system by deterministically reconfiguring
the information structure and corresponding residual test. More
importantly, it does not require any physical effort in either microgrid
or network level. The identification scheme of finding meters being
attacked is proposed as well. Eventually, a well-known IEEE 30-bus
system is adopted to demonstrate the effectiveness of the proposed
schemes.
Abstract: The paper discusses complexity of component-based
development (CBD) of embedded systems. Although CBD has its
merits, it must be augmented with methods to control the complexities
that arise due to resource constraints, timeliness, and run-time deployment
of components in embedded system development. Software
component specification, system-level testing, and run-time reliability
measurement are some ways to control the complexity.
Abstract: This paper presents the experimental results of silicone rubber outdoor polymer insulators in salt fog ageing test based on IEC 61109. Specimens made ofHTV silicone rubber with ATH content having three different configurations, straight shedsalternated sheds, and incline and alternate sheds, were tested continuously 1000 hrs.in artificial salt fog chamber. Contamination level, reduction of hydrophobicity and hardness measurement were used as physical damaged inspection techniques to evaluate degree of surface deterioration. In addition, chemical changing of tested specimen surface was evaluated by ATR-FTIRto confirm physical damaged inspection. After 1000 hrs.of salt fog test, differences in degree of surface deterioration were observed on all tested specimens. Physical damaged inspection and chemical analysis results confirmed the experimental results as well.
Abstract: A long-term campaign for monitoring the
concentration of atmospheric Particulate Matter (PM) was conducted
at multiple sites located in the center and suburbs of the Tokyo
Metropolitan Area in Japan. The concentration of fine PM has shown a
declining trend over the last two decades. A positive matrix
factorization model elucidated that the contribution of combustion
sources was drastically reduced. In Japan, the regulations on vehicle
exhaust emissions were phased in and gradually tightened over the last
two decades, which has triggered a notable reduction in PM emissions
from automobiles and has contributed to the mitigation of the problem
of fine PM pollution.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Based on the fuzzy set theory this work develops two
adaptations of iterative methods that solve mathematical programming
problems with uncertainties in the objective function and in
the set of constraints. The first one uses the approach proposed by
Zimmermann to fuzzy linear programming problems as a basis and
the second one obtains cut levels and later maximizes the membership
function of fuzzy decision making using the bound search method.
We outline similarities between the two iterative methods studied.
Selected examples from the literature are presented to validate the
efficiency of the methods addressed.
Abstract: Breastfeeding has been receiving much attention of late. Prolonged sitting for breastfeeding often results in back pain of the mothers. This paper reports the findings of a study on the effect of some factors, especially lumbar support, on back pain of breastfeeding mothers. The results showed that the use of lumbar support can reduce back pain of breastfeeding mothers significantly. Back pain was found to increase with breastfeeding time and the rate of increase was lower when lumbar supports were used. When lumbar support thickness was increased gradually from zero (no support) to 11 cm., the degree of low back pain decreased; rapidly at first, then slowly, and leveled off when the thickness reached 9 cm. Younger mothers were less prone to back pain than older mothers. The implications of the findings are discussed.
Abstract: Till date, English as a Second Language (ESL) educators involved in teaching language and communication to engineering students face an uphill task in developing graduate communicative competency. This challenge is accentuated by the apparent lack of English for Specific Purposes (ESP) materials for engineering students in the engineering curriculum. As such, most ESL educators are forced to play multiple roles. They don tasks such as curriculum designers, material writers and teachers with limited knowledge of the disciplinary content. Previous research indicates that prospective professional engineers should possess some sub-sets of competency: technical, linguistic oral immediacy, meta-cognitive and rhetorical explanatory competence. Another study revealed that engineering students need to be equipped with technical and linguistic oral immediacy competence. However, little is known whether these competency needs are in line with the educators- perceptions of communicative competence. This paper examines the best mix of communicative competence subsets that create the magic for engineering students in technical oral presentations. For the purpose of this study, two groups of educators were interviewed. These educators were language and communication lecturers involved in teaching a speaking course and content experts who assess students- technical oral presentations at tertiary level. The findings indicate that these two groups differ in their perceptions
Abstract: Petrol Fuel Station (PFS) has potential hazards to the
people, asset, environment and reputation of an operating company.
Fire hazards, static electricity air pollution evoked by aliphatic and
aromatic organic compounds are major causes of accident/incident
occurrence at fuel station. Activities such as carelessness,
maintenance, housekeeping, slips trips and falls, transportation
hazard, major and minor injuries, robbery and snake bites has a
potential to create unsafe conditions. The level of risk of these
hazards varies according to location and country. The emphasis on
safety considerations by the government is variable all around the
world. Developed countries safety records are much better as
compared to developing countries safety statistics. There is no
significant approach available to highlight the unsafe acts and unsafe
conditions during operation and maintenance of fuel station. Fuel
station is the most commonly available facilities that contain
flammable and hazardous materials. Due to continuous operation of
fuel station they pose various hazards to people, environment and
assets of an organization. To control these hazards, there is a need for
specific approach. PFS operation is unique as compared to other
businesses. For smooth operations it demands an involvement of
operating company, contractor and operator group. This study will
focus to address hazard contributing factors that have a potential to
make PFS operation risky. One year data collected, 902 activities
analyzed, comparisons were made to highlight significant
contributing factors. The study will provide help and assistance to
PFS outlet marketing companies to make their fuel station operation
safer. It will help health safety and environment (HSE) professionals
to arrest the gap available related to safety matters at PFS.
Abstract: The validity of Herzberg-s Two-Factor Theory of
Motivation was tested empirically by surveying 2372 chemical fiber
employees in 2012. In the valid sample of 1875 respondents, the
degree of overall job satisfaction was more than moderate. The most
highly valued components of job satisfaction were: “corporate image,"
“collaborative working atmosphere," and “supervisor-s expertise";
whereas the lowest mean score was 34.65 for “job rotation and
promotion." The top three job retention options rated by the
participants were “good image of the enterprise," “good
compensation," and “workplace is close to my residence." The overall
evaluation of the level of thriving facilitation workplace reached
almost to “mostly agree." For those participants who chose at least
one motivator as their job retention options had significantly greater
job satisfaction than those who chose only hygiene factors as their
retention options. Therefore, Herzberg-s Two-Factor Theory of
Motivation was proven valid in this study.
Abstract: Most simple nonlinear thresholding rules for
wavelet- based denoising assume that the wavelet coefficients are independent. However, wavelet coefficients of natural images have significant dependencies. This paper attempts to give a recipe for selecting one of the popular image-denoising algorithms based
on VisuShrink, SureShrink, OracleShrink, BayesShrink and BiShrink and also this paper compares different Bivariate models used for image denoising applications. The first part of the paper
compares different Shrinkage functions used for image-denoising.
The second part of the paper compares different bivariate models
and the third part of this paper uses the Bivariate model with modified marginal variance which is based on Laplacian assumption. This paper gives an experimental comparison on six 512x512 commonly used images, Lenna, Barbara, Goldhill,
Clown, Boat and Stonehenge. The following noise powers 25dB,26dB, 27dB, 28dB and 29dB are added to the six standard images and the corresponding Peak Signal to Noise Ratio (PSNR) values
are calculated for each noise level.
Abstract: Logistics is part of the supply chain processes that
plans, implements, and controls the efficient and effective forward
and reverse flow and storage of goods, services, and related
information between the point of origin and the point of consumption
in order to meet customer requirements. This research aims to
investigate the current status and future direction of the use of
Information Technology (IT) for logistics, focusing on Supply Chain
Management (SCM) and E-Commerce adoption in Malaysia.
Therefore, this research stresses on the type of technology being
adopted, factors, benefits and barriers affecting the innovation in
SCM and E-Commerce technology adoption among Logistics
Service Providers (LSP). A mailed questionnaire survey was
conducted to collect data from 265 logistics companies in Johor. The
research revealed a high level of SCM technology adoption among
LSP as they had adopted SCM technology in various business
processes while they perceived a high level of benefits from SCM
adoption.
Abstract: Supply Chain Management (SCM) is the integration
between manufacturer, transporter and customer in order to form one
seamless chain that allows smooth flow of raw materials, information
and products throughout the entire network that help in minimizing
all related efforts and costs. The main objective of this paper is to
develop a model that can accept a specified number of spare-parts
within the supply chain, simulating its inventory operations
throughout all stages in order to minimize the inventory holding
costs, base-stock, safety-stock, and to find the optimum quantity of
inventory levels, thereby suggesting a way forward to adapt some
factors of Just-In-Time to minimizing the inventory costs throughout
the entire supply chain. The model has been developed using Micro-
Soft Excel & Visual Basic in order to study inventory allocations in
any network of the supply chain. The application and reproducibility
of this model were tested by comparing the actual system that was
implemented in the case study with the results of the developed
model. The findings showed that the total inventory costs of the
developed model are about 50% less than the actual costs of the
inventory items within the case study.