Abstract: With the growth of modern civilization and
industrialization in worldwide, the demand for energy is increasing
day by day. Majority of the world-s energy needs are met through
fossil fuels and natural gas. As a result the amount of fossil fuels is
on diminishing from year to year. Since the fossil fuel is nonrenewable,
so fuel price is gouging as a consequence of spiraling
demand and diminishing supply. At present the power generation of
our country is mainly depends on imported fossil fuels. To reduce the
dependency on imported fuel, the use of renewable sources has
become more popular. In Bangladesh coconut is widely growing tree.
Especially in the southern part of the country a large area will be
found where coconut tree is considered as natural asset. So, our
endeavor was to use the coconut oil as a renewable and alternative
fuel. This article shows the prospect of coconut oil as a renewable
and alternative fuel of diesel fuel. Since diesel engine has a versatile
uses including small electricity generation, an experimental set up is
then made to study the performance of a small diesel engine using
different blends of bio diesel converted from coconut oil. It is found
that bio diesel has slightly different properties than diesel. With
biodiesel the engine is capable of running without difficulty.
Different blends of bio diesel (i.e. B80, B60, and B 50 etc.) have
been used to avoid complicated modification of the engine or the fuel
supply system. Finally, a comparison of engine performance for
different blends of biodiesel has been carried out to determine the
optimum blend for different operating conditions.
Abstract: An analysis is made of the flow of an incompressible viscoelastic fluid (of small memory) over a porous plate subject to suction or blowing. It is found that velocity at a point increases with increase in the elasticity in the fluid. It is also shown that wall shear stress depends only on suction and is also independent of the material of fluids. No steady solution for velocity distribution exists when there is blowing at the plate. Temperature distribution in the boundary layer is determined and it is found that temperature at a point decreases with increase in the elasticity in the fluid.
Abstract: The present work deals with the stabilisation of
organic clay using hydrated lime. Artificial organic clays were
prepared by adding kaolin and different humic acid contents. Results
given by physical testing show that the presence of humic acid has a
drawback effect on the untreated organic clay. The decrease in
specific gravity value was accompanied by a decrease in dry density
and plasticity of clay at higher humic acid contents. Significant
increase in shear strength at 7 days of curing period is observed in the
lime-treated samples up to 5% lime content. However shear strength
of lime-treated organic clay decreases at longer curing periods. The
results given by laboratory testing is further verified by
microstructure analysis. Based on the results obtained in this study, it
can be concluded that the presence of more than 1.5% humic acid
reduces significantly the efficiency of lime stabilization in organic
clays.
Abstract: This paper addresses one important aspect of
combustion system analysis, the spray evaporation and
dispersion modeling. In this study we assume an empty
cylinder which is as a simulator for a ramjet engine and the
cylinder has been studied by cold flow. Four nozzles have the
duties of injection which are located in the entrance of
cylinder. The air flow comes into the cylinder from one side
and injection operation will be done. By changing injection
velocity and entrance air flow velocity, we have studied
droplet sizing and efficient mass fraction of fuel vapor near
and at the exit area. We named the mass of fuel vapor inside
the flammability limit as the efficient mass fraction. Further,
we decreased the initial temperature of fuel droplets and we
have repeated the investigating again. To fulfill the calculation
we used a modified version of KIVA-3V.
Abstract: The principal objective of a water treatment plant is to
produce water that satisfies a set of drinking water quality standards
at a reasonable price to the consumers. The gravel-bed flocculator
provide a simple and inexpensive design for flocculation in small
water treatment plants (less than 5000 m3/day capacity). The packed
bed of gravel provides ideal conditions for the formation of compact
settleable flocs because of continuous recontact provided by the
sinuous flow of water through the interstices formed by the gravel.
The field data which were obtained from the operation of the
water supply treatment unit cover the physical, chemical and
biological water qualities of the raw and settled water as obtained by
the operation of the treatment unit. The experiments were carried out
with the aim of assessing the efficiency of the gravel filter in
removing the turbidity, pathogenic bacteria, from the raw water. The
water treatment plant, which was constructed for the treatment of
river water, was in principle a rapid sand filter.
The results show that the average value of the turbidity level of
the settled water was 4.83 NTU with a standard deviation of turbidity
2.893 NTU. This indicated that the removal efficiency of the
sedimentation tank (gravel filter) was about 67.8 %. for pH values
fluctuated between 7.75 and 8.15, indicating the alkaline nature of
the raw water of the river Shatt Al-Hilla, as expected. Raw water pH
is depressed slightly following alum coagulation. The pH of the
settled water ranged from 7.75 to a maximum of 8.05.
The bacteriological tests which were carried out on the water
samples were: total coliform test, E-coli test, and the plate count test.
In each test the procedure used was as outlined in the Standard
Methods for the Examination of Water and Wastewater (APHA,
AWWA, and WPCF, 1985). The gravel filter exhibit a low
performance in removing bacterial load. The percentage bacterial
removal, which is maximum for total plate count (19%) and
minimum for total coliform (16.82%).
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: A frictionless contact problem for a two-layer orthotropic elastic medium loaded through a rigid flat stamp is considered. It is assumed that tensile tractions are not allowed and only compressive tractions can be transmitted across the interface. In the solution, effect of gravity is taken into consideration. If the external load on the rigid stamp is less than or equal to a critical value, continuous contact between the layers is maintained. The problem is expressed in terms of a singular integral equation by using the theory of elasticity and the Fourier transforms. Numerical results for initial separation point, critical separation load and contact stress distribution are presented.
Abstract: This research paper presents the CFD analysis of
oscillating airfoil during pitch cycle. Unsteady subsonic flow is
simulated for pitching airfoil at Mach number 0.283 and Reynolds
number 3.45 millions. Turbulent effects are also considered for this
study by using K-ω SST turbulent model. Two-dimensional unsteady
compressible Navier-Stokes code including two-equation turbulence
model and PISO pressure velocity coupling is used. Pressure based
implicit solver with first order implicit unsteady formulation is used.
The simulated pitch cycle results are compared with the available
experimental data. The results have a good agreement with the
experimental data. Aerodynamic characteristics during pitch cycles
have been studied and validated.
Abstract: In this paper, we address the problem of adaptive radio
resource allocation (RRA) and packet scheduling in the downlink of a
cellular OFDMA system, and propose a downlink multi-carrier
proportional fair (MPF) scheduler and its joint with adaptive RRA
algorithm to distribute radio resources among multiple users according
to their individual QoS requirements. The allocation and scheduling
objective is to maximize the total throughput, while at the same time
maintaining the fairness among users. The simulation results
demonstrate that the methods presented provide for user more explicit
fairness relative to RRA algorithm, but the joint scheme achieves the
higher sum-rate capacity with flexible parameters setting compared
with MPF scheduler.
Abstract: A numerical study on the influence of electroosmotic flow on analyte preconcentration by isotachophoresis ( ITP) is made. We consider that the double layer induced electroosmotic flow ( EOF) counterbalance the electrophoretic velocity and a stationary ITP stacked zones results. We solve the Navier-Stokes equations coupled with the Nernst-Planck equations to determine the local convective velocity and the preconcentration dynamics of ions. Our numerical algorithm is based on a finite volume method along with a secondorder upwind scheme. The present numerical algorithm can capture the the sharp boundaries of step-changes ( plateau mode) or zones of steep gradients ( peak mode) accurately. The convection of ions due to EOF reduces the resolution of the ITP transition zones and produces a dispersion in analyte zones. The role of the electrokinetic parameters which induces dispersion is analyzed. A one-dimensional model for the area-averaged concentrations based on the Taylor-Aristype effective diffusivity is found to be in good agreement with the computed solutions.
Abstract: The effects of different parameters on the
hydrodynamics of trickle bed reactors were discussed for Newtonian
and non-Newtonian foaming systems. The varying parameters are
varying liquid velocities, gas flow velocities and surface tension. The
range for gas velocity is particularly large, thanks to the use of dense
gas to simulate very high pressure conditions. This data bank has
been used to compare the prediction accuracy of the different
trendlines and transition points from the literature. More than 240
experimental points for the trickle flow (GCF) and foaming pulsing
flow (PF/FPF) regime were obtained for present study.
Hydrodynamic characteristics involving dynamic liquid saturation
significantly influenced by gas and liquid flow rates. For 15 and 30
ppm air-aqueous surfactant solutions, dynamic liquid saturation
decreases with higher liquid and gas flow rates considerably in high
interaction regime. With decrease in surface tension i.e. for 45 and 60
ppm air-aqueous surfactant systems, effect was more pronounced
with decreases dynamic liquid saturation very sharply during regime
transition significantly at both low liquid and gas flow rates.
Abstract: Self-propelled forage harvesters in the 850
horsepower range were tested over three years for fuel consumption,
throughput and quality of chop for corn silage. Cut length had a
significant effect on fuel consumption, throughput and some aspects
of chop quality. Measure cut length was often different than
theoretical length of cut. Where cut length was equivalent fuel
consumption and throughput were equivalent across brands.
Shortening cut length from 17 to 11mm increases fuel consumption
53 percent measured as Mg of silage harvested per gallon of fuel used
and a 42 percent decrease in capacity as tons of fresh material per
hour run time.
Abstract: Considering toxicity of heavy metals and their
accumulation in domestic wastes, immobilization of lead and
cadmium is envisaged inside glass-ceramics. We particularly
focused this work on calcium-rich phases embedded in a
glassy matrix.
Glass-ceramics were synthesized from glasses doped with
12 wt% and 16 wt% of PbO or CdO. They were observed and
analyzed by Electron MicroProbe Analysis (EMPA) and
Analytical Scanning Electron Microscopy (ASEM). Structural
characterization of the samples was performed by powder XRay
Diffraction.
Diopside crystals of CaMgSi2O6 composition are shown to
incorporate significant amounts of cadmium (up to 9 wt% of
CdO). Two new crystalline phases are observed with very
high Cd or Pb contents: about 40 wt% CdO for the cadmiumrich
phase and near 60 wt% PbO for the lead-rich phase. We
present complete chemical and structural characterization of
these phases. They represent a promising way for the
immobilization of toxic elements like Cd or Pb since glass
ceramics are known to propose a “double barrier" protection
(metal-rich crystals embedded in a glass matrix) against metal
release in the environment.
Abstract: The PAX6, a transcription factor, is essential for the morphogenesis of the eyes, brain, pituitary and pancreatic islets. In rodents, the loss of Pax6 function leads to central nervous system defects, anophthalmia, and nasal hypoplasia. The haplo-insufficiency of Pax6 causes microphthalmia, aggression and other behavioral abnormalities. It is also required in brain patterning and neuronal plasticity. In human, heterozygous mutation of Pax6 causes loss of iris [aniridia], mental retardation and glucose intolerance. The 3- deletion in Pax6 leads to autism and aniridia. The phenotypes are variable in peneterance and expressivity. However, mechanism of function and interaction of PAX6 with other proteins during development and associated disease are not clear. It is intended to explore interactors of PAX6 to elucidated biology of PAX6 function in the tissues where it is expressed and also in the central regulatory pathway. This report describes In-silico approaches to explore interacting proteins of PAX6. The models show several possible proteins interacting with PAX6 like MITF, SIX3, SOX2, SOX3, IPO13, TRIM, and OGT. Since the Pax6 is a critical transcriptional regulator and master control gene of eye and brain development it might be interacting with other protein involved in morphogenesis [TGIF, TGF, Ras etc]. It is also presumed that matricelluar proteins [SPARC, thrombospondin-1 and osteonectin etc] are likely to interact during transport and processing of PAX6 and are somewhere its cascade. The proteins involved in cell survival and cell proliferation can also not be ignored.
Abstract: Gas turbine air inlet cooling is a useful method for
increasing output for regions where significant power demand and
highest electricity prices occur during the warm months. Inlet air
cooling increases the power output by taking advantage of the gas
turbine-s feature of higher mass flow rate when the compressor inlet
temperature decreases. Different methods are available for reducing
gas turbine inlet temperature. There are two basic systems currently
available for inlet cooling. The first and most cost-effective system is
evaporative cooling. Evaporative coolers make use of the evaporation
of water to reduce the gas turbine-s inlet air temperature. The second
system employs various ways to chill the inlet air. In this method, the
cooling medium flows through a heat exchanger located in the inlet
duct to remove heat from the inlet air. However, the evaporative
cooling is limited by wet-bulb temperature while the chilling can cool
the inlet air to temperatures that are lower than the wet bulb
temperature. In the present work, a thermodynamic model of a gas
turbine is built to calculate heat rate, power output and thermal
efficiency at different inlet air temperature conditions. Computational
results are compared with ISO conditions herein called "base-case".
Therefore, the two cooling methods are implemented and solved for
different inlet conditions (inlet temperature and relative humidity).
Evaporative cooler and absorption chiller systems results show that
when the ambient temperature is extremely high with low relative
humidity (requiring a large temperature reduction) the chiller is the
more suitable cooling solution. The net increment in the power output
as a function of the temperature decrease for each cooling method is
also obtained.
Abstract: In recent years, tuned mass damper (TMD) control systems for civil engineering structures have attracted considerable attention. This paper emphasizes on the application of particle swarm application (PSO) to design and optimize the parameters of the TMD control scheme for achieving the best results in the reduction of the building response under earthquake excitations. The Integral of the Time multiplied Absolute value of the Error (ITAE) based on relative displacement of all floors in the building is taken as a performance index of the optimization criterion. The problem of robustly TMD controller design is formatted as an optimization problem based on the ITAE performance index to be solved using the PSO technique which has a story ability to find the most optimistic results. An 11- story realistic building, located in the city of Rasht, Iran is considered as a test system to demonstrate effectiveness of the proposed method. The results analysis through the time-domain simulation and some performance indices reveals that the designed PSO based TMD controller has an excellent capability in reduction of the seismically excited example building.
Abstract: Palm shell obtained from coastal part of southern
India was studied for the removal for the adsorption of Hg (II) ions.
Batch adsorption experiments were carried out as a function of pH,
concentration of Hg (II) ions, time, temperature and adsorbent dose.
Maximum removal was seen in the range pH 4.0- pH 7.0. The palm
shell powder used as adsorbent was characterized for its surface area,
SEM, PXRD, FTIR, ion exchange capacity, moisture content, and
bulk density, soluble content in water and acid and pH. The
experimental results were analyzed using Langmuir I, II, III, IV and
Freundlich adsorption isotherms. The batch sorption kinetics was
studied for the first order reversible reaction, pseudo first order;
pseudo second order reaction and the intra-particle diffusion reaction.
The biomass was successfully used for removal Hg (II) from
synthetic and industrial effluents and the technique appears
industrially applicable and viable.
Abstract: Natural disasters, including earthquake, kill many people around the world every year. Society rescue actions, which start after the earthquake and are called LAST in abbreviation, include locating, access, stabilization and transportation. In the present article, we have studied the process of local accessibility to the injured and transporting them to health care centers. With regard the heavy traffic load due to earthquake, the destruction of connecting roads and bridges and the heavy debris in alleys and street, which put the lives of the injured and the people buried under the debris in danger, accelerating the rescue actions and facilitating the accessibilities are of great importance, obviously. Tehran, the capital of Iran, is among the crowded cities in the world and is the center of extensive economic, political, cultural and social activities. Tehran has a population of about 9.5 millions and because of the immigration of people from the surrounding cities. Furthermore, considering the fact that Tehran is located on two important and large faults, a 6 Richter magnitude earthquake in this city could lead to the greatest catastrophe during the entire human history. The present study is a kind of review and a major part of the required information for it, has been obtained from libraries all of the rescue vehicles around the world, including rescue helicopters, ambulances, fire fighting vehicles and rescue boats, and their applied technology, and also the robots specifically designed for the rescue system and the advantages and disadvantages of them, have been investigated. The studies show that there is a significant relationship between the rescue team-s arrival time at the incident zone and the number of saved people; so that, if the duration of burial under debris 30 minutes, the probability of survival is %99.3, after a day is %81, after 2days is %19 and after 5days is %7.4. The exiting transport systems all have some defects. If these defects are removed, more people could be saved each hour and the preparedness against natural disasters is increased. In this study, transport system has been designed for the rescue team and the injured; which could carry the rescue team to the incident zone and the injured to the health care centers. In addition, this system is able to fly in the air and move on the earth as well; so that the destruction of roads and the heavy traffic load could not prevent the rescue team from arriving early at the incident zone. The system also has the equipment required firebird for debris removing, optimum transport of the injured and first aid.
Abstract: The methanolic extracts from seeds of tamarind
(Tamarindus indica) was prepared by Soxhlet apparatus extraction
and evaluated for total phenolic content by Folin-Ciocalteu method.
Then, methanolic extract was screened biological activities (In vitro)
for anti-melanogenic activity by tyrosinase inhibition test, antiinflammation
activity by cyclooxygenase 1 (COX-1) and
cyclooxygenase 2 (COX-2) inhibition test, and cytotoxic screening
test with Vero cells. The results showed that total phenolic content,
which contained in extract, was contained 27.72 mg of gallic acid
equivalent per g of dry weight. The ability to inhibit tyrosinase
enzyme, which exerted by Tamarind seed extracts (1 mg/ml) was
52.13 ± 0.42 %. The extract was not possessed inhibitory effect to
COX-1 and COX-2 enzymes and cytotoxic effect to Vero cells. The
finding is concludes that tested seed extract was possessed
antimelanogenic activity with non-toxic effects. However, there was
not exhibited anti-inflammatory activity. Further studies include the
use of advance biological models to confirm this biological activity,
as well as, the isolation and characterization of the purified
compounds that it was contained.
Abstract: Perturbed-Chain Statistical Association Fluid Theory (PC-SAFT) equation of state (EOS) is a modified SAFT EOS with three pure component specific parameters: segment number (m), diameter (σ) and energy (ε). These PC-SAFT parameters need to be determined for each component under the conditions of interest by fitting experimental data, such as vapor pressure, density or heat capacity. PC-SAFT parameters for propane, ethylene and hydrogen in supercritical region were successfully estimated by fitting experimental density data available in literature. The regressed PCSAFT parameters were compared with the literature values by means of estimating pure component density and calculating average absolute deviation between the estimated and experimental density values. PC-SAFT parameters available in literature especially for ethylene and hydrogen estimated density in supercritical region reasonably well. However, the regressed PC-SAFT parameters performed better in supercritical region than the PC-SAFT parameters from literature.